Search Documents

By A. S. Murphy, E. V. Manlapig, C. Green, J. W. Parkinson

Historically in Australia and the United States many coal mines deposited raw wash plant fines into large slurry impoundments. At the time the technology and market economics did not exist to make it viable to recover coal from these tailings. Today better technology exist to dredge and clean the tailings and there are circumstances where government regulations and market forces have come together to make coal recovery from these old tailings impoundments economically viable. This paper discusses the processes and equipment being used in tailings impoundment reclamation operations in Australia and the United States, and discusses the economic forces driving these operations.

Jan 1, 2001

By R. C. Emmett

The industrial practice of concentration of solids and production of clear solution by gravity sedimentation is an old technology. Through the years, many devices have been designed and built to aid this process. One of the more significant developments was a revolving rake mechanism to convey settled material to a central discharge point of a circular tank, patented in 1907(1). In recent years, clarification systems employing parallel inclined plates have appeared on the market; the original device utilizing this principle was patented in 1886(2). Numerous other methods have been invented, tested, discarded and sometimes re-invented, all with the specific intention of improving the capacity of a particular settling area. Sedimentation theory, as expressed in Stokes' Law, shows that the rate of settling of a particle is directly proportional to the difference in density between the particle and the surrounding liquid and, more significantly, proportional to the square of the particle diameter. Anything that can increase the latter will greatly assist sedimentation and, as a result, flocculation always has been an integral part of sedimentation. Most materials suspended in aqueous media are naturally flocculent to some degree and, hence, are readily concentrated by sedimentation, although sometimes very slowly.

Jan 1, 1978

By Dennis A. Swyt

In current post-industrial America, U.S. manufacturing is undergoing major changes both in the technology of its production and in the size and composition of its workforce. At the same time that computers and robotics move the shop floor toward becoming the unmanned "factory of the future" [1], they increase the need within the overall production enterprise for new types of technicians and engineering professionals [2]. Based on previous works which examined, first, the evolution of the technology of manufacturing toward the flexibly-automated factory of the future and, second, the technical- professionalization of U.S. manufacturing sectors [1,3], this paper looks briefly at the workforce of the U.S. metals industry.

Jan 1, 1989

By W. L. Hollinshead, Alwin Poltinger

GENERAL Tunneling by hand digging is as old as the history of humans. Mechanized tunneling did not begin to replace manual methods until around the beginning of the 19th century(Brunel patent, 1818). It brought with it a higher degree of safety for the workers and a much higher rate of boring. But for any kind of tunneling, an accurate and feasible method of survey must be accomplished during mining. That means, that for each tunnel project the most efficient survey method must be devised. The method to be defined depends on the spatial curve, diameter, speed of tunneling method, purpose of tunnel and contractual accuracy. The final accuracy of a finished tunnel is heavily dependent upon three critical elements: 1. Quality of the above ground survey 2. Tunnel traverse and directional transfer from above ground 3. Guidance for the mining job. Combining The Survey And The Guidance System Since the guidance system (GS) is one of the critical factors in the determination of the tunnel final accuracy, it is necessary to analyze how the directional control and tunnel traverse measurements can be effectively integrated into a GS. Any guidance system, whether manual or high technology, must continually detect and compensate for movement of its theodoliteor laser station standpoint. Movement beyond a preset allowable amount must generate a warning or error message to the user. Additionally, optical refraction can interfere with the results. Refraction will have an effect on any kind of optical GS. Therefore, careful selection of target and standpoint locations can minimize, but not completely eliminate, the influence of refraction. Some GS technologies, such as Gyro-based systems, are immune to the effects of refraction, but have other, methodical errors which will be described later in this paper. GUIDANCE Overview Why is a guidance system necessary? A GS, whether manual or automatic, compares the design direction and slope of a tunnel with the current position of the mining

Jan 1, 1997

By P. M. Solozhenkin

The proposed technology of antimony calcine processing includes ferrochloride leaching of calcine, reducing solutions, hydrolysis of hydrochloride solutions with antimony oxochloride isolation, synthesis of antimony trioxide by SbOCl neutralization and its drying, regeneration of hydrolysis solutions. The optimum parameters of separate stage of process has been determined and the chemical character of process has been given. During the leaching of calcine we succeeded to transfer 92.16- 95.66% antimony to solution. On the worked out sheme we attained recovery of antimony to antimony trioxide near 90 .5% Antimony triozide contains 99.5% Sb2O3. The composition of sinter burdens for pigments preparation "Naples Yellow" different colours from brightly-yellow, yellow and lightly yellow has been proposed. Three-sulfuretted antimony-antimonic cinnabar have been prepared by precipitation of antimony solutions by potassium sulfur-bearing solution. The prepared compounds correspond to inorganic pigments for artistic paint. The amorphous antimony-ferrous black we prepared by aluminium cementation of hydrochloric antimony solutions. The ferrous black were used as artistic paints and for coating of metals by antimony.

Jan 1, 1995

By Ralph B. Peck

Exploration The technology of underground construction and particularly of tunneling, both now and in the future, starts with knowledge of the properties of the medium surrounding the tunnel. Although we are trying to develop machines that can excavate tunnels independently of the properties of the medium, and although we may achieve some success in this direction, we seem always to be brought up short by a paradox: With increasing sophistication of machines and with increasing complexity of construction jobs, our methods are likely to become more sensitive rather than less sensitive to changes in the medium. I suspect that the need for more precise knowledge of subsurface conditions in advance of construction will increase rather than decrease as time goes by. In the recent anniversary issue of Engineering News Record, Probing the Future, Senior Editor Bill Jacobus prophesies highly sophisticated devices to probe the unknowns of the earth's soil and rock materials. He envisions that "drill holes to obtain borings will give way to rock-melting coring devices". He may be right; it is hard to argue the accuracy of predictions of the future. It seems to me more likely, however, that the rock-melting probe will be simply one more in

Jan 1, 1974

By Edwin G. Johnsen

Underground mining is relatively safe today, but no technique or equipment is completely fool proof and 100% reliable. The only sure way to prevent accidental death or injury to underground workers is to remove them completely from the hazardous environment. This alternate approach to underground work is now feasible. Tunnelling and mining systems can be built that could be remotely controlled by men operating consoles in a surface control room. This concept, called a teleminer, would use recently developed remote control technology to remove man from underground work but still give him the capability to remotely operate mining and excavating equipment as if he were actually in the working area. It is appropriate to present this concept in the session "Environmental Controls" because the rationale for environmental control in underground areas can be significantly modified if man is excluded from the underground operation. The development of teleminers cannot only reduce or eliminate most of the requirements for conventional environmental control, but it can also create new and powerful techniques for rapid tunnelling and excavation. TELEMINER CONCEPT The concept of remotely controlled mining machines is neither new nor untried.(1)(2) Conventional remotely controlled mining equipment employs the standard techniques of extending the controls of the equipment to a remote console. For example, the rotary cutters on a remotely controlled tunnelling machine are started or stopped by a human operator turning a switch on the remote control console.

Jan 1, 1997

By P. J. Miranda, C. G. Anderson, L. G. Twidwell

Titanium is a metal of increasing worldwide strategic importance. The Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech of the University of Montana is currently directing two titanium research initiatives. The first program, Titanium Extraction Mining and Process Engineering Initiative (TEMPER), is focused on producing low cost titanium through the identification and development of new mining, beneficiation and extraction technologies which will significantly reduce the cost of titanium production. This will directly benefit worldwide commercial applications. Secondly, CAMP is evaluating new technologies for fabrication of titanium utilizing the Free Form Titanium Fabrication (FFTF) initiative. These technologies may drastically reduce the cost and time to manufacture titanium components. Because of the high strength to weight ratio of titanium coupled with its superior corrosion characteristics, these programs will be of vital importance to expanding the commercial and strategic applications of titanium. An overview of these two new titanium initiatives will be presented in this paper.

Jan 1, 2005

By L. Neuman

Reclamation and permit applications for mines tend to be very detailed and complicated documents. Depending on its complexity, the application may have to be reviewed in detail for water quality, water quantity, wetland and upland habitat, wildlife issues, waste disposal, historical and archeological significance, other environmental factors, and financial surety sufficiency. To reduce review time and cut costs to the applicant, this paper identifies the most common mistakes that can lead to delays in the application process.

Jan 1, 2004

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of X-ray backscatter, iron K, fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1993

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of x-ray backscatter, iron Ka fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1992

By Peter T. Luckie

Up until the past couple of years, thermal coal dryers were only used to dry midwest and eastern United States bituminous coals. These dryers were primarily installed at coal preparation plants to freeze proof the coal and lower the transportation costs per BTU. Today thermal coal dryers are being specified to dry western sub-bituminous and lignite coals for these and other reasons brought about by the intense interest in coal gasification and liquefaction. One reason for drying western coals ahead of a coal gasification plant is the elimination of surface moisture which would prevent efficient sizing of the coal, since feed material size consist is very important in most commercial coal gasification processes. Thermal dryers are being proposed for liquefaction processes because of the need for a feed material containing approximately 4% or less total moisture Future coal gasification processes may also need to reduce feed material moisture content.

Jan 1, 1975

By C. J. Hall

The simplest natural ventilation cycle is similar to a Joule or Brayton cycle. This comprises two reversible adiabatic processes in the shafts and constant pressure processes underground and on surface. The thermal efficiency of such a cycle is given by the temperature increase in the downcast shaft divided by the absolute temperature of the air at the bottom of the downcast shaft, and is independent of the temperature increase underground. This efficiency is comparable to the Carnot efficiency, which is the greatest possible value between constant temperature reservoirs, source and sink. Two variations of the Joule cycle are investigated, using numerous work examples. In the first, dry air is used as the working substance, a fan is provided at the top of the upcast shaft, and various mass rates of flow are used with frictionless shafts and a constant resistance value in the horizontal mine workings. The lost work less the fan work gives the natural ventilation work, and this divided by the enthalpy increase in the workings gives the thermal efficiency. The thermal efficiency increases dramatically with mass rate of flow, although the enthalpy increase remains constant. This appears to violate the second law of thermodynamics, since the frictionless case has a Carnot efficiency. When the lost work is added to the enthalpy increase, however, the efficiency decreases slightly from the Carnot value, to conform with the second law. This increase in efficiency with mass rate of flow is often referred to as the reheat effect, although the air is not heated. The second investigation is similar to the first, except that the air entering the downcast shaft contains a small amount of water vapor, and there is evaporation in the mine workings only, until the air entering the upcast shaft is saturated. There is, of course, condensation in the upcast shaft. In this case, it is not possible to calculate the Carnot efficiency, but the thermal efficiency is 20 to 40% of the similar dry air values. This decrease is much more than can be accounted for by the larger value of specific heat for water vapor. In addition, the natural ventilation work is almost constant with increased mass rate of flow, and the thermal efficiency based on heat addition tends to decrease. The thermal efficiency based on heat and lost work decreases in conformity with the second law. The reasons for the differences in behavior between dry and moist air are not readily apparent.

Jan 1, 1991

By T. Yegulalp, K. S. Lackner

Zero emission coal plants capture their own CO2 emissions. Since they have no smoke stack, they emit no pollutants to the air. Zero emission plants circulate a gas stream, to which fresh fuel is added and from which spent fuel and impurities are removed as solids or liquids. Coal is gasified via hydrogenation, steam reforming or CO2 gasification (Boudouard reaction). The gas is oxidized in a fuel cell and the resultant water and CO2 are partially removed before returning the remaining gas to the gasifier. The high conversion efficiency of zero emission power plants, which exceeds 70% even in realistic designs, stems from combining fuel cells with careful heat management. The paper generalizes the concepts and outlines the thermodynamic basis of zero emission power plants.

Jan 1, 2004

By Joseph G. Selmeczi

Lime and limestone-based SO2 scrubbing processes have demonstrated reasonably good success in removing low concentrations of SO2 from flue gases. While most of the operating problems experienced in the early days of scrubbing have been worked out, problems usually increase and removal efficiency drops with increased amounts of SO2 present in the gas stream. In order to overcome these difficulties, yet still taking advantage of lime and limestone as the lowest cost neutralizing agents, a host of so-called double- alkali systems were developed. These processes take advantage of cations such as Na+ and NH4+ capable of forming highly water soluble bases or basic salts, such as hydroxide, carbonate or sulfite, which having been neutralized or acidified by the absorbed SO2 can be regenerated with a lower cost base such as lime.

Jan 1, 1974

By Irving Hoch

INTRODUCTION The demand for tunnelling can be related to urban population size and density; often, tunnelling occurs when a certain city size and density threshold is reached, and increases thereafter as a function of those population characteristics. Subways for rail mass transit are the most notable example, of course, but tunnels for water supply and perhaps for sewerage can also be related to size and density. As cities grow large they sometimes outgrow their local water supply and have to import water from distant places via tunnels; witness New York City, Los Angeles and San Francisco. And it has been suggested that Chicago use deep tunnels for storm water storage because tertiary treatment to meet water quality standards will require treating storm water runoff.(1) Other uses of underground space also increase with urban density, e.g., underground parking, concourses and shopping centers such as Rockefeller Center in New York City and the Place Ville-Marie in Montreal. These examples can be viewed as illustrative of the central point of urban land economics. As the number of people locating in a place increase, they bid up land values and make the more intensive use of land economic, with land defined to embrace the space both above and below the surface. Hence, we are led to think about the city, and of urban land use, in three dimensions. Now, if we accept the relation of underground space use to urban size and density, recent demographic trends seem anything but hopeful for future tunnelling demand: urban density is declining, population growth is slowing down generally, and there

Jan 1, 1974

By C. O. Brawner

Approximately 7 billion tons of soil, rock and ore are currently being excavated in open pit mines and quarries on the North American continent at the present time. As the depth of excavation increases and the grade of ore being mined reduces, the safety and economy of the stability of the pit slopes becomes increasingly important. The magnitude of the potential influence on economics can be appreciated from the results of recent full scale field studies by Kennecott Copper Corporation at the Kimbley pit near Ely Nevada (Merrill, 1968). This pit was originally excavated with an average wall slope of 45°. Based on detailed studies it appeared that a slope of 610 would be stable. Subsequent excavation to this slope proved the original pit could have been steepened by 16° during production.

Jan 1, 1968

By Eugene F. Casey

The next ten to fifteen years will be exciting ones for the construction industry because three city agencies alone have started or will start, on tremendous expansion programs, the cost of which will exceed a total of four billion dollars. The major portion of this work will be done by the use of tunnelling methods. *Tunnelling is construction by any method of a covered cavity of predesigned geometry whose final location and use under the surface, whose cross-sectional area is greater than two sq. meters. The New York City Transit Authority's expansion program will provide for approximately 52 miles of new subways. The Board of Water Supply has already started on City Tunnel No. 3 which, when completed will provide the City with enough water until the year 2000, and the Board of Water Resources has embarked on a tremendous program to clean up the surrounding waters. Yes, these will be exciting years, particularly when one reads about the new novel exotic methods of rock breaking and disintegration, coupled with the new methods of soft ground tunnelling.

Jan 1, 1997

By TOMI GIORGIO DE, Ricardo Tichauer

Mineral exploration is a key factor for success in the mining industry. However, exploration best practices are often ignored in small-scale mining. This works presents the Tichauer-DeTomi Matrix, a methodology that measures the level of compliance of exploration programs in small-scale mining with the industry best practices. The matrix has been applied to three projects in Brazil: an artisanal gold mine in the state of Pará, a small-scale manganese project in the state of Bahia, and a small-scale manganese project in the state of São Paulo. The application of the matrix resulted in indexes that represent the level of maturity of the exploration program in each project and indicate priority actions for reduction of the geological uncertainty. Therefore, the Tichauer-DeTomi Matrix has shown potential to be a useful tool for assessment of geological uncertainty in small-scale mining. As a risk indicator, it may contribute to promoting investment in small-scale mining and development for communities that depend on this activity around the world.

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.