Search Documents

By J. LeRoy Peterson

This paper presents some of the theoretical aspects as well as some results of actual plant operation of the Ty-Hukki Classifier. Dual classification steps within a unit vessel are achieved by controlled separation of the sand product under turbulant flow conditions, followed by further classification under strictly laminar flow conditions. Plant operation has shown some of the benefits of the superior sharpness of classification to be reduction of circulating load in grinding circuits, prevention of overgrinding, increase in mill feed rate and consequent reduction in cost per ton of ore.

Jan 1, 1966

By T. McNulty

The author was privileged to find employment as a uranium mill chemist for The Anaconda Company while working his way through school in the mid-1950s. He then served Anaconda in various technical and management positions until 1980. This paper describes the prevalent technologies employed by uranium producers, briefly describes various mines and mills in the U. S., and memorializes a few of the thousands of men and women who contributed to the U. S. Uranium Boom. Following isolation of uranium as an element by M. H. Klaproth in 1789, uses of uranium were confined primarily to pigments, glass coloring agents, and ceramic glazes. In 1896, Antoine Becquerel found that uranium is radioactive, releasing particles and energy as it decays. In 1898, Pierre and Marie Curie isolated radium from uranium and learned that it can be an effective treatment for some types of cancer. In 1939, it was discovered that the isotope U235 is fissionable1 . Up to this point, nearly all uranium production was from pitchblende concentrates made in Bohemia, Canada, and the Belgian Congo. In 1938, only about 5 percent (23.85 short tons) of global output was produced from ores of the carnotite mineral that were being mined in the U.S. By the early-1950s, physicists in many countries had begun to recognize the potential for nuclear chain reactions. Ernest Rutherford (UK), Frederick Soddy (UK), and Leo Szilard (US) explained transmutation of elements and formulated the principle of “atom splitting”. In 1934, Marie Curie’s daughter, Irène, and her husband, Frédéric Joliot, identified uranium as the most viable source for this new form of energy. The basic fission process was unraveled by German scientists in December 1938. After Hitler’s army seized the uranium deposits in Czechoslovakia, many feared that Germany would build the first nuclear weapon.

Mar 2, 2022

By R. H. Moore, B. D. Breitenstein

INTRODUCTION The United States Uranium Registry (USUR) tissue program was funded in 1978 by the United States Department of Energy (DOE) through its Human Health and Assessments Division, and registrant enrollment began in 1980. It is operated by Hanford Environmental Health Foundation (HERF), Richland, Washington, with support provided by Pacific Northwest Laboratory (PNL).** The USUR tissue program is the first systematic effort to contact and gain assistance of workers occupationally exposed to uranium and to seek and study uranium deposition in human tissue. This paper describes the program objectives, populations selected for study, procedures for enrolling workers in the program, types of tissue to be studied, and analytical procedures to be used. PROGRAM OBJECTIVES The objectives of the USUR tissue program are to: 1) Determine the distribution and concentration of uranium, if any, in the tissues of occupationally exposed workers. 2) Compare bioassay measurements of exposed individuals with the results of analyses of tissues obtained at autopsy. 3) Seek evidence of histopathologic changes related to any uranium deposition that may be present. 4) Conduct analyses of whole bodies, when available, to obtain more precise data on the uranium burdens, if any, in the body and organs, and especially the distribution in parts of the body, such as the skeleton, that are not usually accessible for sampling. 5) Develop data that will assist in evaluating a) the accuracy of current in-vivo measurement techniques, b) the propriety of existing regulations, and c) the adequacy of current protection programs. SELECTION OF POPULATIONS FOR STUDY Selection of the populations for the USUR tissue program was based on studies of the United States Uranium Registry described elsewhere (0c81). Potential populations for study were quite varied because of occupational exposure to different chemical forms of uranium, different levels and eras of exposure, varying ability to identify populations exposed in the past, and the general interest and cooperativeness of the populations. Nevertheless, certain identifiable populations emerged that were both willing to participate in the study and likely to provide useful information. Among the targeted populations are individuals who were exposed to uranium prior to the existence of modern exposure standards. These individuals are presently being enrolled by the USUR. The reliability of concentration and distribution data and the demonstration of effects are more likely in such individuals than in those who have received less exposure. However, the targeted groups also include individuals who Have been exposed to permissible levels of uranium, and reference employees in uranium plants who have not worked with uranium. The lesser exposures are of immediate interest because of the rarity of heavy exposures under current standards. The sampling of potentially exposed individuals with negative in-vivo measurement results may serve to check the adequacy of in-vivo measurements in the detection of deposition. [ENROLLMENT PROCEDURE] The enrollment of participants follows three patterns. 1) Presently employed workers are enrolled by the cooperative efforts of USUR staff with the medical, industrial relations, and/or health physics personnel of the uranium facility. Volunteers may be enrolled by medical personnel at the time of their physical examination or by health physics personnel at the time of a bioassay or lung counting procedure. Follow-up after initial contacts with currently employed uranium workers is carried out by on-site personnel, but subsequent follow-up is the responsibility of the Registry. 2) Retired workers are contacted by mail, with a covering letter from their former employer supporting the principles of the study but leaving participation in the program on an entirely voluntary basis. 3) An alternate method of enrollment is to obtain a USUR autopsy consent after death from the next of kin. As part of enrollment in the program, permission is requested for access to the individual's medical and exposure data, and a short occupational history is filled out. The autopsy permission agreement signed by the individual is for an initial period of 5 years; the USUR ordinarily seeks renewal of the agreement upon its expiration. While this agreement provides

Jan 1, 1981

Cement in 1975 indeed did operate in an unfriendly environment. World recession, escalating costs, fuel crises, reduced product demand . . . . all led to market conditions detrimental to industry profit margins and investment re turns. During the year plant utilizations fell, break-even points were raised, and competitive moves introduced to move built up inventory levels. A number of cement plants were temporarily taken out of production to help alleviate specific situations. Meanwhile, under resultant financial pressure, several companies omitted dividend payments, changed their top executives, and reorganized and reduced staff overheads. It was a difficult year for cement, yet a much more ominous note was sounded in permanent plant closings. Four more cement operations were shut down in 1975; to date in 1976 we know for sure of three additional plant closings, while rumour has it that at least one more may not be in production by year-end. The somber feature is found within the descriptions of the closed facilities, and in the stated reasons for their being taken out of cement manufacture.

Jan 1, 1976

By Lawrence Pelham

The importance of fluorspar to the United States and the world and the role it plays in industry and society extend far beyond that which is suggested by its measured production and consumption quantities and declared value. Compared to many other industrial minerals, the annual worldwide consumption of 5 million short tons valued at less than $500 million are not impressive figures. Fluorspar is made special primarily because of its status as a critical and strategic commodity; it is essential for the processing of most steels and all aluminum. It also is the raw material for the production of elemental fluorine, which plays a part in uranium refining.

Jan 1, 1988

By Patrick Shea

Old mine workings are found throughout the Western United Sates on lands administered by the U.S. Bureau of Land Management, U.S. Forest Service and private lands. Some of these mine workings date back to the late 1800s. There may be as many as 100,000 sites on lands administered by the National Park Service, U.S. Forest Service and Bureau of Land Management. The U.S. Department of the Interior has worked with the U.S. Geological Survey, the U.S. Forest Service, the U.S. Environmental Protection Agency, and western state governments to identify and prioritize these sites on Bureau of Land Management, National Park Service and U.S. Forest Service administered lands. This presentation will discuss the accomplishments we have made to date to clean up inactive and abandoned mine sites, focusing primarily on lands administered by the Bureau of Land Management.

Jan 1, 2000

By Peter L. Hofmann

Significant quantities of nuclear wastes were first generated in 1944 as a byproduct of the national defense program. To establish the current inventories and future projections of nuclear waste products is not a simple task. The Oak Ridge National Laboratory recently issued a report which now constitutes the official basis for nuclear waste inventories and projections. Radioactive wastes originate from five major sources (U .S. Department of Energy, 1980b) : (1) From the commercial nuclear fuel cycle related to the production of electricity , (2) From defense related activities, (3) From institutions such as hospitals, universities, and research foundations, (4) From industrial uses of radioisotopes, and (5) From mining and milling of uranium ores.

Jan 1, 1981

By Z. Jin, D. DePaoli, P. Zhang

"Phosphate beneficiation in Florida generates more than one tonne of phosphatic clay, or slime, per tonne of phosphate rock produced. Since the start of the practice of large-scale washing and desliming for phosphate beneficiation, more than 2 Gt of slime has accumulated, containing approximately 600 Mt of phosphate rock, 600 kt of rare earth elements (REEs) and 80 million kilograms of uranium. The recovery of these valuable elements from the phosphatic clay is one of the most challenging endeavors in mineral processing, because the clay is extremely dilute, with an average solids concentration of 3 percent, and fine in size, with more than 50 percent having particle size smaller than 2 µm, and it contains nearly 50 percent clay minerals as well as large amounts of magnesium, iron and aluminum. With industry support and under funding from the Critical Materials Institute, the Florida Industrial and Phosphate Research Institute in conjunction with the Oak Ridge National Laboratory undertook the task to recover phosphorus, rare earths and uranium from Florida phosphatic clay. This paper presents the results from the preliminary testing of two approaches. The first approach involves three-stage cycloning using cyclones with diameters of 12.4 cm (5 in.), 5.08 cm (2 in.) and 2.54 cm (1 in.), respectively, to remove clay minerals followed by flotation and leaching. The second approach is a two-step leaching process. In the first step, selective leaching was conducted to remove magnesium, thus allowing the production of phosphoric acid suitable for the manufacture of diammonium phosphate (DAP) in the second leaching step. The results showed that multistage cycloning with small cyclones is necessary to remove clay minerals. Selective leaching at about pH 3.2 using sulfuric acid was found to be effective for removing more than 80 percent of magnesium from the feed with minimal loss of phosphorus.IntroductionFlorida phosphate ore, or “matrix,” as it is called locally, contains three different mineral groups that have to be separated from each other: (1) phosphate minerals, (2) clay minerals and (3) quartz, or sand. As mined, the phosphate and sand particles are embedded in compacted mud, or clay-balls. Before separation can begin, all of the particles must be liberated from the matrix of mud. The very first unit operation in the beneficiation process is to disaggregate the various particles. This actually starts while the matrix is flowing through the multimile pipeline from the mine to the beneficiation plant. While in the pipeline, the matrix is exposed to shear forces as it passes through the various centrifugal pumps along the pipeline. These intense shear forces cause a significant percentage of the sand and phosphate particles to be liberated from the clay-balls by the time they arrive at the plant. Once they reach the plant, the first goal is to finish disaggregating the clay, and follow that by making a size separation at 1 mm. This processing is conducted in the washer, consisting of a large rotating trammel screen and a few stages of log washer, screens and hydrocyclones. In all of the currently operating beneficiation plants, the washer is a large structure that receives the matrix, screens it and then discharges a pebble phosphate product sized larger than 1.0 mm and a slurry of liberated clay, sand and phosphate particles that are smaller than 1.0 mm."

Jan 1, 2017

By Boshou Bian

Air quantity is the primary parameter governing the working condition of a mine fan. In order to improve the fan performance and efficiency, reduce its energy consumption, and guarantee mine safety, it is very important to obtain an accurate value. However, generally speaking, the fan ducting or drift on surface is very short in distance and contains sharp bends. The air quantity of the mine is so concentrated in this way that the air velocity becomes very high, and the airflow, either in the fan drift before the fan impeller or at the downstream diffuser, is very turbulent. Therefore, no anemometer is satisfactory because there is too much difference between the measured value and the actual value of air quantity at the mine fan.

Jan 1, 1989

By Keith G. Wallace, K. M. (Chris) Chmura, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) performed a feasibility analysis for the purpose of either modifying, supplementing, or replacing its two main mine fans. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) fa¬cility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Since the centrifugal fans were installed in 1988, multiple op¬erational and performance concerns have been identified. A com¬prehensive engineering study was conducted in 1995 to: 1) Qualify and quantify operational concerns, 2) Evaluate possible alternatives, and 3) Recommend an optimum solution. Multiple system modification and/or replacement scenarios were evaluated with associated cost estimates developed. The study considered replacement with either centrifugal or axial fans. Multiple fan duties are required at the WIPP. Therefore, Variable Frequency Drives and Inlet Vane Controls (IVC) were investigated for centrifugal fans. In-flight adjustable blades were investigated for axial fans. The study indicated that replacing the existing system with two double-width, double-inlet centrifugal fans equipped with IVCs was the best choice. This alternative provided the most desirable combination of: 1) ensuring the required operational readiness, and 2) improving system performance. The WIPP is currently planning to replace the first fan in 1997.

Jan 1, 1997

By Richard E. Steffens

The underground portion of Duke Power Company's Bad Creek Pumped Storage Project in northwestern South Carolina consists of a powerhouse cavern (132 m. long, 23 m. wide, 50 m. high), 407 meters of shafts and approximately 3615 meters of tunnel, both lined and unlined, with diameters varying from 4.2 meters to 9.0 meters. A case history is presented, including the early pilot tunnel exploratory work and how this affected design, the design of the project, and the excavation, rock support and tunnel lining work. Problems and experiences encountered during the construction are given. The effects of high horizontal insitu stresses in the granitic gneiss are discussed along with solution taken.

Jan 1, 1989

By David J. Leeds

Increased interest in the utilization of the underground environment for water conveyance tunnels, vehicular tunnels, room and pillar type storage chambers, and military installations has focused attention on the possible effects of seismic activity on the stability of these types of structures. Earthquake experience has generally been related to the seismic stability on the surface of the earth. To establish aseismic design criteria, we attempt to predict the seismic exposure of a given site, both in terms of the spectrum of motion to which the structure must react favorably, and the recurrence rate of that motion. Experience gained from studying the effects of the Plowshare underground nuclear tests on existing tunnels and mines, coupled with the experience of the behavior of tunnels and mines in earthquake regions, provides us with an insight to predict the possible effects of earthquakes on underground openings and to establish design criteria. The type of damage ranges from minor fracturing and movements along pre-existing joints or faults through deformation of openings to collapse. The methods used to establish the seismic design criteria for an underground opening require modification of surface criteria to account for the difference in both amplitude and spectra underground. An aseismic evaluation should be performed on all important projects in areas exposed to possible earthquake motion. To perform this evaluation, information is required pertaining to the geometry and properties of structure and ground. Dynamic as well as static properties are required. A prediction of performance can be derived by exposing a model of the site, expressed in terms of its properties and geometry, to a design earthquake.

Jan 1, 1997

By A. J. Lynch

For over 30 years the JKMRC has been conducting research aimed at improving the understanding of comminution and classification processes. The result of this research has been the development of a range of comminution and classification models which has been successfully applied in numerous optimization and design studies throughout the Australian Minerals Processing Industry. This paper reviews the current status of our understanding of the mechanisms which govern comminution and classification processes. Outlines of mathematical models of these processes are described together with examples of their application in design and optimization studies.

Jan 1, 1992

By F. L. Kadey

A discussion of fillers would not be complete without allotting adequate time to that unique and different mineral material, diatomaceous silica. Historical references to its use challenge the aesthetic aspect of man's curiosity; whereas modern scientific tools have provided a dimension of measurement that has motivated many of its more recent applications. A brief review of what is already known is in order. The diatom is a unicellular, plant-like, microscopic organism, related to the algae1. Its natural function appears to be that of a food for other marine or lacustrine organisms, The diatom's "claim to fame" from an industrial viewpoint is dependent on the fact that it secretes an opaline siliceous skeleton that must survive, chemically and structurally, the geologic processes that caused its formation in the first place; its subsequent demise, burial, consolidation, and alteration; and finally, its ultimate exploitation by man--in somewhat that order. In addition to its siliceous nature, the skeletal structure of the diatom possesses a variety of shapes, patterns, and sizes that have not only been the intrigue of microscopists for decades, but have served to set diatomite apart as an industrial mineral; and have reserved for it applications that cannot be satisfied by any other material. Its chemical inertness, its intricate structure, and its intrinsic hardness-coupled with fineness and friability-- are generally known and have accounted for its application in a wide range of filtration and filler uses. The increasing use of the electron microscope has considerably expanded our knowledge of heretofore unseen secondary and tertiary structure of submicron dimension in the diatom valve. The development of electro-sensing methods of particle size measurement which seem to supersede sedimentation and microscopic techniques has portrayed size distribution in a more realistic light. Interest in the surface chemistry of these silica structures has further strengthened our understanding for certain uses. Thus, new tools and ideas have made possible the introduction of diatomite into such sophisticated technologies as that of chromatographic supports, its improved utility in paint applications for the control of gloss and sheen, and its usefulness in the entirely new concept of "Dry Acid Concentrates." Each of these applications has been discussed elsewhere before people particularly interested in analytical chemistry, in paint, and in liquid handling, respectively, where the diatom has been a means to an end. The emphasis here, before the mining fraternity, however is on diatomite as a raw material with reference to the uses mentioned above. It is therefore toward an awareness and understanding of diatomite properties pertinent to these newer filler applications that this paper is directed.

Jan 1, 1967

By Simon D. Handelsman

Technical co-operation activities of the Department of Technical Co-operation for Development of the United Nations Secretariat have included the introduction of electronic data processing techniques in mineral sector projects for several years; computers have been provided to countries in Africa, Asia and Latin America. Advisory services are provided to interested developing countries at their request concerning applications for various uses in mineral sector activities. They include advice on appropriate hardware and software depending upon the requirements of the particular Government. The Department's activities in this area are described. The input from a Group of Experts on this subject convened by the United Nations, and their conclusions and recommendations, are also discussed.

Jan 1, 1986

By Harvey Parker

This is part two of an article on the prominent role that the United States and its industry leaders have played on the International Tunnelling and Underground Space Association (ITA), which represents the underground construction and underground space industries worldwide. The U.S. is officially represented in ITA by UCA of SME. (Part one is in T&UC, June 2007, pp 39-42) Tunnel advances in 1960s and 1970s The 1960s and 1970s were active and productive times for the U.S. tunneling industry. During that time, federal programs, sponsored by the Federal Railroad Administration (FRA), the Office of High Speed Ground Transportation (OHSGT) and the Advanced Research Projects Administration (ARPA), stimulated tunnel research and development. Also, the American Society of Civil Engineers (ASCE) and SME collaborated to create the Underground Construction Research Council (UCRC) and the Rapid Excavation and Tunneling Conference (RETC) series.

Jan 1, 2007

By Harvey Parker

The International Tunnelling and Under-ground Space Association (ITA) is a nonprofit organization that represents all aspects of the tunneling and underground space industry worldwide. The United States has had a prominent role in ITA since its 1974 inception. ITA was formed as a result of a worldwide survey conducted in the early 1970s by the Organization for Economic Cooperation and Development (OECD). Bill Lucke was in charge of tunnels for the U.S. Federal Railroad Administration and was a member of the organizing committee that created ITA. He became a vice president of ITA. Jack Lemley served as President of ITA from 1983 to 1986. Dick Robbins was very active in ITA and served for many years both as a member of the Executive Council and as First Vice President. Harvey Parker has served as President of ITA for the last three years and will serve as Past President for the next three years. Moreover, there are many individuals and companies from the United States that have contributed significantly to the activities and the success of ITA. There have been several active Working Group Animateurs from the U.S. and there have been significant contributions from many individuals as well as companies from the U.S. Several engineers from the U.S. are currently serving ITA in a leadership role. The Underground Construction Association of SME (UCA of SME) is the official organization representing the U.S.. SME Executive. [ ] Director Dave Kanagy and UCA President Tom Peyton were instrumental in the U.S.?s role at ITA during the last few years. Peyton has been the official delegate to ITA. Henry Russell and Christian Ingerslev are both Animateurs of ITA working groups. This article will introduce ITA and its activities. A subsequent article will describe the ITA in more detail and will discuss the significant role the U.S. has played in the development and success of ITA.

Jan 1, 2007

By S. D. Abbott

Mines are filled with a mixture of gases, some of which are toxic, flammable, or explosive. Others serve as early reporters of impending problems. Mines monitor these gases in order to ensure the safe, efficient operation of the facility and avoid losses or disasters. Two different approaches to monitor these gases have historically been taken. One kind of device measures the amount of each gas present by using selective detectors (e.g. handhelds and spectrometers). Another kind separates the mixture of gases into the individual constituents, then measures the amount of each gas present (e.g. gas chromatographs). Handheld units are the most widely used, but gas chromatographs are the most powerful yet underutilized units available to enhance mining operations. There are many misconceptions about the nature, applicability and proper use of each type of device, and little data is available. Up to this point, many people had only the manufacturers? claims to guide them. This study was undertaken to clarify the range of applicability, important characteristics, and value in use of these units in real-world situations. An additional goal of the study was to provide ways to evaluate comparative data, and thus aid mining operations in choosing the most beneficial and reasonable ways to use such devices in various situations and contexts.

Feb 23, 2014

By Jennifer King, Julius Strid, Steve Brandon

The Upper Hidden Basin Diversion (UHBD) tunnel was driven approximately 1.2 miles by the drill-and-blast method primarily through massive granite bedrock geology for the Kodiak Electric Association, Inc. (KEA) in Kodiak, Alaska. The tunnel was driven from both portals with a constant 11-ft straight-leg horseshoe cross-section. The design and construction of the tunnel was driven by logistics and weather conditions due to its remote location and the rugged terrain of the project setting. This paper will discuss the successful completion of a challenging project over a ve-year period from preliminary planning through the design and construction phases.

Jun 23, 2024

By L. F. Ruppert, W. D. Watson, S. J. Tewalt, L. J. Bragg

The U.S. Geological Survey recently completed a digital coal resource assessment model of the Upper Pennsylvanian Pittsburgh coal bed which indicates that of the original 34 billion short tons [31 billion tonnes] of coal, 16 billion short tons [14 billion tonnes] remain after subtracting mined-out coal. When technical, environmental, and social restrictions are applied to the remaining Pittsburgh coal model, only12 billion short tons [11 billion tonnes] are available for mining. Our assessment models estimate that up to 0.61 billion short tons [0.55 billion tonnes], 2.7billion short tons [2.4 billion tonnes], and 8.5 billion short tons [7.7 billion tonnes] could be available for surface mining, continuous mining, and longwall mining, respectively. This analysis is an example of a second-generation regional coal availability study designed to model recoverability characteristics for all the major coal beds in the U.S.

Jan 1, 2000