Search Documents

The global tunneling industry has many challenges, both technically and financially, with the latter likely to be a significant feature over the next few years. Many industries have ad-opted standard practices in order to overcome specific technical challenges, from which standard out-comes are anticipated. In tunneling, however, every project is unique so standardized practice is not easy. This requires original thinking and being open to adopting new techniques and technologies as they emerge. Sprayed waterproofing is a hot industry topic and a paper recently presented at the North American Tunneling conference not only discussed this methodology for achieving a dry tunnel but also how it can reduce build costs and construction time. Despite their being relatively few ?universal truths? throughout the tunneling industry, there is one opinion that appears to be shared by most in the sector, ?all tunnels leak.?

Jan 1, 2010

By A. D. Davis, C. J. Webb, T. V. Durkin

This project took a watershed approach in the evaluation of water-quality impacts from past mining activities and current restoration projects in the Bear Butte Creek basin, a small and well-defined drainage in a heavily mined area of the northern Black Hills. The basin contains numerous inactive and abandoned mines, as well as a heap-leach surface gold mine. Bear Butte Creek normally loses all of its discharge to sinkholes in the Madison Limestone aquifer. Thus, it can affect the water quality of this regionally important water resource. Water-quality data were analyzed, stream surveys were conducted and two abandoned-mine restoration projects were monitored to evaluate the effectiveness of the watershed approach and to identify practical remediation techniques that could be applied to other watersheds. A geographic information system (GIS) was developed to organize information on stream quality, abandoned mine locations, and other geologic and hydrologic data. The watershed approach toward assessing and reclaiming abandoned mines appears to be effective when compared to a point-source approach that might improve water quality at specific sites but not result in significant overall improvement to the watershed because of adjacent sources.

Jan 1, 2000

By James R. Boulton

Fire detection using Carbon Monoxide sensors is based on the assumption that a rise in the level of Carbon Monoxide in the atmosphere over a fixed, predetermined ambient level is indicative of a fire. The method is simple, reliable, and effective in those mines where the only source of CO is from undesired combustion. Ambience for this purpose is defined as that level of the gas that is present on a day to day basis whose source is not a fire. In a diesel powered mine the level of CO can and does vary so widely from hour to hour and minute to minute that the selection of a predetermined, fixed level represents a compromise between sensitivity and reliability. The compromise is a best of both and worst of both situations and the computer system often resembles the little boy who cried wolf instead of a state of the art early fire monitoring and detection system. Cyprus Coal personnel have developed method of determining the ambient level of CO in the atmosphere on a real time basis and using that dynamic ambient level to determine whether or not a fire exists in the mine. The method has been given the name of Wave Trend Crossing.

Jan 1, 1991

By K. V. Raj, A. T. Weakley, A. L. Miller, D. A. Parks

Diesel particulate matter (DPM) is a common and well-known health hazard in the mining environment. The current approved method for monitoring both the organic and elemental carbon (OC, EC) portions of DPM is a laboratory method with a turnaround time of approximately one week. In order to evaluate exposure levels and take corrective action before overexposures occur, a portable real-time device capable of quantifying both OC and EC is needed. To that end, researchers from the National Institute for Occupational Safety and Health (NIOSH) designed and tested a device based on narrow bandpass optical filters that is capable of targeting infrared absorbance bands associated with DPM. Five optical bandpass filters were chosen based on previous work quantifying DPM using Fourier-transform infrared (FT-IR) spectrometry. The resulting device, referred to as a filtometer, is optimized to exclusively determine DPM and could serve as a cost-effective, field-portable alternative to laboratory-grade FT-IR analysis and instrumentation. The performance of the filtometer was investigated by calibrating FT-IR data from DPM (dependent variable) to the filtometer spectra (predictor variables) using a partial leastsquares (PLS) and ordinary least squares (OLS) approach. The square of the correlation coefficient and root-mean-square error of cross validation m

Mar 2, 2022

By K. Tabra

In a mine operation, the proper strategy to handle residues is one of the main concerns, in particular when dealing with mine/plant liquid effluents. Most active water treatment systems at metal mines rely on standard alkali-addition procedures. However, the increase of mineral prices, stricter environmental standards and high metal content in some effluents, has led to the development of alternative treatment techniques for their removal and/or recovery. This article presents a roadmap to face mine wastewater treatment requirement, with focus on two active treatment strategies: 1) conventional lime-based technology and 2) the use of NaSH or Fe(OH)3 for metal precipitation and separation, including possible valuable elements recovery. The Roadmap consists of 1) Approach to effluent treatment 2) Characterization 3) Precipitation tests 4) Solid/liquid separation tests and 5) Economic analysis.

Feb 27, 2013

By S. Z. Galiyev

In this paper the basic approach to the present planning and quality management of open-pit ore streams is presented. This is accomplished within the framework of a unified system of information management for the administration of a geotechnological complex on open-pit development of mineral deposits.

Jan 1, 2003

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

The paper addresses heat stress in underground coal mines, which poses significant threats to miners’ health, safety, and productivity. It involves a comprehensive ventilation survey in three deep and mechanized underground coal mines in India. Using VentSim software, 3D simulation models were developed to predict heat stress conditions and explore the application of auxiliary ventilation and spot coolers to reduce heat stress.

Oct 1, 2023

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress in underground coal mines is a major threat to the health and safety of the miners. Hence, managing heat and prediction of heat stress in advance is essential for maintaining a safe, healthy, and productive underground mine environment. In this study, an extensive ventilation survey has been carried out in three different deep and mechanized underground coal mines. The ventilation survey data are used to develop 3D simulation models with the VentSim™ software to predict the conditions that could cause heat stress in underground mine workings. The developed 3D models predicted well the wet-bulb globe temperature (WBGT), a recognized indicator of potential heat stress, with a coefficient of determination (R2) of 0.986, 0.994, and 0.993 for Mine-A, Mine-B, and Mine-C, respectively. Moreover, through 3D modelling, the applications of auxiliary ventilation and spot coolers to reduce the wet-bulb globe temperature (WBGT) for improving the underground workplace environment have been explored. The study demonstrated that auxiliary ventilation and spot coolers can help in significant reduction of heat stress conditions in an underground mine environment. By application of auxiliary ventilation, to increase air volumes, and spot coolers, the WBGT index in mining faces is reduced by 1.2–1.4 °C and 3.9–5.4 °C, respectively. Therefore, it is concluded that the spot coolers are more effective in reducing the heat stress conditions in hot and humid underground mine environments in comparison with auxiliary fan that is used to increase the air volume and velocity. This study opens up a new horizon of 3D simulations for heat stress management in underground mines. The outcome of this study will be useful for the researchers, mine operators, and environmentalists understanding the heat stress contributors and their control in underground mine environment.

May 10, 2023

By Jim Armbrust

JAMIE DAVIS: Our next speaker is Jim Armbrust, maintenance manager at Phelps Dodge, Morenci. Jim's presentation is titled "We Need More Training-How to Get the Biggest Bang for the Buck." We've talked a lot about preventative maintenance and we've heard several people talk about training. How do we train to use all these systems? How do we educate people? This will be a nice little wrap-up for us. JIM ARMBRUST: One common theme from this morning's talk is that we need more training. That's exactly what we'll be talking about for the next few minutes.

Jan 1, 1998

By Janusz S. Laskowski

Studies carried out over the last 10 years reveal that precipitating particles which may appear in alkaline solutions of long-chain amines and in acidic solutions of fatty acids exhibit clear isoelectric points around pH 10.6-1 1 for dodecylamine and around pH 2.5-3 for fatty acids. These colloidal species can accumulate at solid/liquid and liquid/gas interfaces and affect flotation. While the precipitate in solutions of fatty acids apparently can chemically interact with the mineral surfaces and is flotation-active if sufficiently long conditioning time is available, the cationic flotation of quartz in alkaline solutions is depressed by the colloidal precipitate. The experimental data available in literature on the adsorption, electrokinetic, contact angle and surface forces measurements in the solutions of the weak electrolyte collectors are analyzed and the role played by the precipitate is discussed. It is shown that these concepts allow for an explanation of the selective flotation of sylvite from halite with long-chain amines in potash ore flotation.

Jan 1, 1999

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By William R. Yernberg

The Society of Economic Geologists (SEG) held its biennial conference May 14 through 16, 2006, in Keystone, CO. SEG is an international organization with about 3,500 individual members with interests in economic geology. The 2006 SEG conference theme was “Wealth creation in the minerals industry — integrating science, business and education.” The conference exceeded expectations with 705 participants, including 102 students, from 44 countries. The conference featured 30 oral presentations, 24 professional posters and more than 70 student posters. The conference also included a trade show with 50 vendors, numerous field trips, workshops and social activities.

Jan 1, 2006

By J. W. Jang, J. J. Moore, I. Iwasaki

The wear behaviors of grinding media with different chemical composition and microstructures in wet grinding of a quartz-pyrrhotite mixture were investigated under various environments. The marked ball wear tests showed that the wear rate could be minimized by a suitable combination of martensite and ferrite within the same ball. A ball composed solely of hard martensite exhibited increased wear under an oxygen environment, while balls composed of both soft ferrite together with hard martensite exhibited decreased wear due presumably to the difference in their passivation behaviors. The galvanic interaction between the two phases as well as among these phases and an electroactive mineral were investigated through electrochemical measurements under abrasive condition in a slurry. The rates of formation of passive film controlled the corrosion currents of the high chromium steel media. Corrosive wear and its effect on flotation are discussed using the passivation kinetics model thereby developed.

Jan 1, 1990

By J. W. Jang

The wear behaviors of grinding media with different chemical compositions and microstructures in wet grinding of a quartz-pyrrhotite mixture was investigated under various environments. The marked ball wear tests showed that the wear rate could be minimized by a suitable combination of martensite and ferrite within the same ball. A ball composed solely of hard martensite exhibited increased wear under an oxygen environment, while balls composed of both soft ferrite together with hard martensite exhibited decreased wear due presumably to the difference in their passivation? behaviors. The galvanic interactions between the two phases as well as among these phases and an electroactive mineral were investigated through electrochemical measurements under abrasive conditions in a slurry. The rates of formation of passive films controlled the corrosion currents of the high chromium steel media. Corrosive wear and its effect on flotation are discussed using the passivation kinetics model thereby developed.

Jan 1, 1989

By Jr. Chilson

This paper addresses the slurry pump industry as it exists today by touching on the business aspects, and by discussing research and development for material metallurgy and hydrodynamics for wear improvement which reduce operating and maintenance cost for the customer. It demonstrates why OEM parts give better value for cost.

Jan 1, 1996

By J. H. Tylczak, R. Blickensderfer, D. J. Singleton

As part of its research on wear of mining and mineral processing equipment, the US Bureau of Mines evaluated the erosion-corrosion characteristics of 12 alloys in phosphoric acid waste water. Tests were conducted on 2- and 5-cm-diam specimen8 in 12- and 60-cm-diam ball mills by grinding phosphate rock in gypsum pond water with an initial pH of 1.6. For comparison, grinding tests also were conducted in tap water. Static corrosion tests in gypsum pond water also were carried out. For all alloys tested, the wear by erosion-corrosion was greater than the sum of erosion plus static corrosion. A low-alloy, high-carbon steel and a high-manganese, nitrided stainless steel were the most cost-effective materials

Jan 1, 1987

By M. J. Meulendyke, J. D. Purdue

Within the mineral processing industry, a range of grinding conditions exists which include semiautogenous grinding (SAG),rod milling, and conventional ball milling. Each of these mill environments presents a unique environment for grinding media, requiring the application of specific physical and chemical properties for optimum grinding media performance. The environments are characterized by varying degrees and combinations of abrasive, corrosive, and impact wear. An extensive test program has been conducted to determine the extent wear rates vary between these different applications. Test results are related to production results, ball size, and mill operating conditions.

Jan 1, 1990

By M. J. Meulendyke

Within the mineral processing Industry. a range of grinding conditions exists which include semi-autogenous grinding (SAG), rod milling. and conventional ball milling. Each of these mill environments presents a unique environment for grinding media, requiring the application of specific physical and chemical properties for optimum grinding media performance. The environments are characterized by varying degrees and combinations of abrasive, corrosive, and impact wear. An extensive test program has been conducted to determine the extent wear rates vary between these different applications. Test results are related to production results, ball size, and mill operating conditions.

Jan 1, 1989

By C. Frenzel

Tunnel boring machines (TBM) utilize disc cutters as the primary means for excavating hard rock. Depending on rock excavatability and rock abrasivity disc cutters can exhibit significant wear. A detailed analysis has been carried out to characterize failure modes and wear patterns of disc cutters. The relationship between rock properties, op-eration of the TBM, and failure modes of cutting tools is clearly high-lighted. On that basis a prediction tool for disc cutter consumption has been developed that allows to estimate not only gross cutter life, but accounts for cutterhead design, premature cutter changes, and disc cutter repair costs.

Jan 1, 2011

By S. Constantinescu

The alloys mainly used for short (or segmented) chip material cutting (cast iron, porcelain, etc) are alloys of the WC-Co type; in some cases with small additions of other carbons. The same alloys but of different granulometric classes are also used for pieces exposed to wear (wire drawing, moulds) The higher performance of the WC-Co alloys in chip machining applications is accounted for by their very good heat conductivity, which is 2-3 times higher than that of fast steels. The hard-alloys producers can resort to a wide range of possibilities to achieve variation of properties of a WC-Co composition and thus they can adapt their products to the particular type of tools they may choose to manufacture. The present metallography technique allows for a correct identification and evaluation of hard sintered carbons structures. The metallography approach is an indispensable method of investigation and control in the industry.

Jan 1, 2008