Search Documents

By Thomas Gleason

Wet scrubbing of fine coal from Thermal dryers poses a number of problems in adapting the gas cleaning equipment for required clean-up of the fine particulate matter. Among then are: 1. The dust In the gases leaving the Thermal dryer cyclone-s is often extremely fine with high percentages of the total dust loading less than one (1) micron in size. 2, The flue gas entering the scrubber is corrosive since the coal fired in the thermal dryer furnace is in the range of 0.7% by weight sulphur or higher. Therefore comparatively high cost stainless steel alloys or corrosion resistant linings are required for a satisfactory service life. 3. Requirements for residual coal loadings leaving the gas e scrubber are continually being lowered while modern coal preparation operation is imposing heavier burdens on the collection system through introduction into the Thermal dryer system of very fine coal previously not recovered. The advent of flotation systems in increasing numbers is typical of this trend 4. The installation of a scrubbing system on Thermal dryers is made primarily to reduce air pollution and product recovery value is of little or no value. Therefore the operating costs, that is, of gas pressure drop and water requirements must be held to a minimum.

Jan 1, 1962

By W. C. Dailey

National Steel Pellet Co. operates eight 8.2-m diameter by 5.5-m long (87- x 18-ft) SAG mills to grind 15.24 Mt (15 million It) of taconite ore per year. Improvements to increase mill throughput, lower steel consumption, lower power consumption, and increase grinding efficiency will be discussed.

Jan 1, 1987

By B. Hearn, Malcolm J. McPhersqn

Since 1993 Inco Ltd. has been using wet shotcrete at Stobie Mine. Through an evolving process the mine has reduced the thickness and fiber content of its steel fiber reinforced (sfr) shotcrete. However, the shotcrete support is used without any other type of ground support. A process referred to as bolt less shotcrete. Boltless shotcrete is used as the primary ground support method in development headings when the sub level caving front passes through the development drifts which now serve as migrating ore draw points. Although there are references of drifts and tunnels supported by shortcrete only, written accounts are rare. The empirical nature of most underground support designs makes them of limited value in a boltless environment. Considerable amounts of material testing and insitu trials have been completed in order to estimate material property strengths. Material testing, for adhesion, flexural strengths and compressive strength along with observational insitu data have been used to evaluate the performance of shotcrete. Punch tests on panels have also been undertaken in order to gain insights on the limitations of the two dimensional testing common to the laboratory. All these design aspects have been successfully utilized to design an efficient ground support process.

Jan 1, 1998

By Georges E. Vaillant

Air pollution control in primary aluminum smelter . Various processes are known for air pollution in electrolysis plants. Mainly two systems have to be taken into consideration: -Treatment of concentrated gases collected directly from hooded pots. This is normally achieved by either dry or wet process. This is not the object of this paper as these processes have been already described. -Treatment of low concentrated fumes. A certain amount of gaseous and solid fluoride (35 % of total fluor pollution) goes out of the hooded pot. Gases commonly called secondary fumes are generally treated by wet process. The object of 'this paper is to describe two plants with specific treatment for secondary fumes. 1/ A plant in operation in Vlissingen (Netherlands) for PECHINEY. 2/ Presentation of tests carried out by a specialized Company. The results of such tests have been used for the design of the scrubbers presently under construction for ALUMINIO ESPANOL San Ciprian (Spain).

Jan 1, 1978

By Stephen Stone, Kerby Dobbs, G. Richard Whittecar, W. Lee Daniels, Zach Agioutantis, Tess Thompson

A common result of Environmental Impact Assessments associated with mining projects is the construction of new wetlands in areas disturbed by mining operations. Where appropriate, this mitigation may be considered an integral part of the mine reclamation process under the principles of sustainable development in the minerals industry. Wetbud is a new tool for estimating wetland water budgets using available weather data and site-specific topographic, soil and geohydrologic data, coupled with mass balance mathematics. Wetbud is primarily intended as a planning tool for use in the design of created wetlands, but it can also be applied to native wetlands or wetland restoration sites where the required input parameters can be specified. Wetbud can be run in its basic form where wetland topography, soil parameters and groundwater flux are simplified, or in the advanced form, where these parameters are included in a more complex approach via integration of the MODFLOW package, a free 3D program that was developed by the United States Geological Survey. Both versions can also include overbank flow hydrology sources and the advanced form can also model sloping and irregular topography. The program downloads weather data from the nearest applicable station and selects appropriate wet-normal-dry (W-N-D) years following a modest user data clean-up step. Wetbud also has the ability to utilize existing short-term (e.g. 6 to 9 months) groundwater data from an up-gradient well to simulate longer-term groundwater level inputs for the selected W-N-D years. In addition, Wetbud features a “Wizard” version that comes pre-loaded with 14 pre-selected weather data sets for all areas of Virginia that can develop a simple monthly water budget in less than 15 minutes – a feature that could be expanded anywhere geographically with historic weather data.

Jan 1, 2017

By L. E. Mercando

The proposed Flambeau Mining Project is based on a high grade copper deposit located approximately one mile southwest of Ladysmith, Wisconsin. The project involves only the mining, crushing, and shipping of ore to facilities outside of Wisconsin for processing. The Wisconsin environmental regulations include provisions for identifying wetlands, the requirements for minimizing the disturbance of wetlands, and the need to establish new wet-lands to replace any wetlands which have to be disturbed.

Jan 1, 1991

By Kent D. Gastreich

As the number of prime surface coal mining sites diminishes with time and with the potential for increased coal demand, areas that were previously not mined because of their difficult mining conditions, marginal economics, and controversial environmental nature, will have to be considered if surface coal mining is to continue in the future. Such sites include areas near major rivers, streams, and lakes. The name most commonly given to these areas by regulatory agencies is "wetlands". The exact definition(s) to the term "wetland" will be discussed later in this paper. Most coal operators are now more than familiar with permitting requirements under the Surface Mining Control and Reclamation Act of 1977 (SMCRA). The SMCRA permanent regulatory program recognizes the fact that coal mining operations will periodically encounter streams, wetlands, etc. Although discussed in various sections of the permanent program regulations, the relationship of coal mining operations to wetlands is particularly evident in the performance standards regarding hydrologic balance and protection of fish, wildlife and related environmental values.

Jan 1, 1980

By X. Yin

Surface force measurements based on atomic force microscopy (AFM) are used to describe the wettability of surfaces, specifically kaolinite basal plane surfaces at a high resolution. The kaolinite particles (~500 nm) were ordered with either the silica tetrahedral face exposed or the alumina octahedral face exposed, and surface force measurements were made between a hydrophobic diamond-like-carbon (DLC) tip and the kaolinite faces at pH 4, which is around the isoelectric point of the DLC tip. Under these conditions, the effect of electrostatic interaction should be eliminated and only van der Waals interactions and hydrophobic-hydrophobic interactions are expected to contribute to the surface force. The wettabilities of the surfaces were determined from the magnitude of the surface force. Wettabilities of the kaolinite basal planes thus determined were compared with the corresponding wettabilities of talc and mica surfaces, which are well-known to be naturally hydrophobic, and hydrophilic surfaces, respectively. The results reveal that the silica tetrahedral face of kaolinte has a modest level of hydrophobicity, which may be due to the lack of hydrogen bonding sites. In contrast, the alumina octahedral face showed no hydrophobicity, since a layer of surface hydroxyl groups is present at the alumina face, resulting in a relatively strong interaction between this surface and water molecules. It is expected that, with a better understanding of the surface properties of kaolinite, further improvements in flotation separations and dewatering may be achieved.

Feb 1, 2012

By W. H. Jang

Although surface chemistry fundamentals of semi-soluble minerals have been studied by many researchers, detailed understanding of these systems is still incomplete. In-situ FT-IR/IRS techniques have recently been used to successfully describe the adsorption of carboxylates at semi-soluble mineral surfaces. However, the wetting characteristics of these adsorbed films require further consideration. In this regard, the hydrophobicity and stability of transferred Langmuir-Blodgett (LB) monolayers of fatty acids at fluorite and calcite surfaces has been studied by contact angle measurements with polar and apolar liquids. Generally, it was found that the transferred LB monolayers of fatty acids at a calcite surface are unstable whereas such monolayers transferred at a fluorite surface are stable, as revealed from advancing and receding contact angle measurements. These results are believed to be due to the incomplete reaction of fatty acid monolayer at the calcite surface. In addition it was found that a closely packed well-ordered stearate monolayer with good hydrophobicity, equivalent to that of a transferred LB monolayer, can be formed at fluorite surfaces by spontaneous adsorption and self-assembly from aqueous solutions.

Jan 1, 1995

Water contact angles in the air/water/francolite, fuel oil/water/francolite and fuel oil/water/quartz systems were measured to describe the wetting characteristics of these minerals. It was found that white francolite is more hydrophilic than black and tan francolite both in the absence and presence of fatty acid addition. The contact angle measurement results do not correlate very well with the flotation response and it appears that kinetic aspects of the bubble attachment process play an important role in the francolite-fatty acid flotation system.

Jan 1, 1997

By J. Drelich

The highly-efficient and economically-feasible technology for bitumen recovery from US oil sands using a water extraction approach was developed at the end of the last century. This water-based bitumen extraction process has been optimized based on observations and analysis of microscopic mechanisms of bitumen release from oil sands and the bitumen transfer to a froth product as well as measurements of interfacial properties of bitumen. The wetting mechanisms that occur in the diluent-assisted water-based processing of US oil sands include bitumen film rupture and recession on sand grains and bitumen transfer to nucleated and injected gas bubbles. These mechanisms are reviewed in this contribution.

Jan 1, 2007

By J. -G. Swanson

Dust control in longwall coal mining depends primarily on the prevention of dust at the source and secondarily on the suppression of airborne dust. One of the primary methods for the prevention of dust is the wetting of the coal face prior to extraction, which can be achieved with water spray systems installed on the shield supports. The spray droplets must travel across the airway to the longwall face, where high ventilation air speeds can entrain water droplets and prevent them from reaching the face thus minimizing the dust control at the source. Through an evaluation of spray plume characteristics in a wind tunnel, the droplet size and droplet drift behavior was determined. This drift behavior was examined by evaluating the spray plume concentration drop and the droplet size shift near the nozzle exit at varying air speeds. Based on these evaluations, CFD modeling was applied to simulate the spray behavior for varying geometries. These results led to the selection of appropriate spray nozzles capable of carrying water droplets to the face at higher air speeds, resulting in an adequate wetting of the coal face and reduced dust generation.

Jan 1, 2012

By Terry M. Hertel

The chemistry of waters processed by Acid Rock Drainage water treatment plants can affect the Total Suspended Solids quality of the plant effluents. The sulfate ions in the ARD water will combine with the calcium ions from the lime that is used to adjust pH to form calcium sulfate. When the sulfate content of the waters to be treated is greater than about 1400 parts per mil­lion, the resulting calcium sulfate concentration will be approx­imately 2100 parts per million. This concentration is above the saturation point for calcium sulfate, and the salt will drop out of solution until the concentration falls below the saturation point. This "salting" phenomenon affects the total suspended solids of the treatment plant effluents by virtue of the fact that the salts will report to the filtration apparatus used for the analy­sis. This scenario is exacerbated as an effluent sample ages. Zortman Mining's water treatment plant effluent was being affected by "salting" during the spring and summer of 1995, and it seemed as though the effluents were exceeding the TSS lim­its; for no obvious reason. A testing program was initiated to verify an observation that "salting' was taking place. Treatment plant samples were collected and allowed to age, with TSS analyses being performed every day that the samples aged. Synthetic solutions were also prepared to study the "salting" phenomenon.

Jan 1, 1996

By E. Sehner, G. Van Weert

Metal chloride pyrohydrolysis is a fifty year old technology, operating satisfactory in many plants around the world, mainly on ferrous chloride, The capabilities and costs of its two equipment options (spray roaster and fluid bed pyrohydrolysis) are well known. Why is the technology not more widely used in mineral processing, beyond the production of MgO and upgraded TiO2slag? After briefly reviewing chloride vs. sulphate process characteristics and existing plant operations, this paper will discuss pyrohydrolysis options for the mine developer using the processing of ilmenite, siliceous zinc oxides and oxidic nickel / cobalt ores as examples.

Jan 1, 2003

By S. D. Rosenthal

"This paper will share my ‘shift in career direction’ journey from corporate mine engineer, with 31 years of mining various commodities with a wide range of responsibilities in a variety of countries, to the world of academia. There are times in one’s career that a change is required, albeit perhaps not as drastic of a change as moving to teaching. This paper will share how the transition arose, the decision to make the change, the challenges of the first year in academia, and the journey within academia going into the second year. INTRODUCTION As a graduate of the Montana College of Mineral Science and Technology (Montana Tech) with a B.S. Mining Engineering degree in May of 1982, my first job with Utah International in the Farmington area took me back to my home state of New Mexico. Some of you will remember that the early 1980’s was not a period of prolific opportunities for mining engineers; given low commodity prices, especially for copper (for example, Anaconda Company had been taken over by Arco and was in the midst of closing down its Butte operations). Coal was good and the learning opportunities abounded with Utah (which became BHP and then BHP Billiton). Gold was taking off in the mid to late 1980’s thanks to use of cyanide and heap leaching technology improvements, coupled with deregulation of the gold price, so I ventured off to work in the gold industry with a (then) junior Canadian company called Barrick at a new acquisition of theirs known as Goldstrike. That same gold surge was causing a shortage of iron ore mining engineers in Australia so after a few years in Nevada, I uprooted the family and left for a little town in the Pilbara of West Australia, known as Newman, to work in the iron ore industry with BHP Iron Ore. An initial short overseas posting turned into six plus years before transferring to BHP’s Indonesian steam coal mines in Kalimantan on the island of Borneo. BHP was going through a rough period following some ill-fated projects (Magma copper purchase, Beanup and HBI) and was reviewing assets and staffing so internal opportunities became scarce. Employees were encouraged to ‘leave the company and find work elsewhere.’ So, off I go to Argentina to try copper mining in the Andes with Minera Alumbrera. This short stint in South America was followed by a move to another mining town, Morenci, Arizona, and a posting with Phelps Dodge (now Freeport McMoran). After 12+ years without living close to snow we moved to the Denver area in a new position with Newmont Mining Corporation. Along the way I became a Professional Engineer (Nevada) and completed a Masters in Project Engineering and Management. After 11 years with Newmont, I moved to Butte, Montana where I accepted a position as Assistant Professor of Mining Engineering."

Jan 1, 2015

By S. D. Rosenthal

"This article will share my ‘shift in career direction’ journey from corporate mine engineer, with 31 years of mining various commodities with a wide range of responsibilities in a variety of countries, to the world of academia. There are times in one’s career that a change is required, albeit perhaps not as drastic of a change as moving to teaching. This paper will share how the transition arose, the decision to make the change, the challenges of the first year in academia and the journey within academia going into the second year.As a graduate of the Montana College of Mineral Science and Technology (Montana Tech) with a B.S. mining engineering degree in May of 1982, my first job with Utah International in the Farmington, NM area took me back to my home state of New Mexico. Some of you will remember that the early 1980s was not a period of prolific opportunities for mining engineers, given low commodity prices, especially for copper (for example, Anaconda Co. had been taken over by Arco and was in the midst of closing down its Butte operations). Coal was good and the learning opportunities abounded with Utah (which became BHP and then BHP Billiton).Gold was taking off in the mid to late 1980s thanks to use of cyanide and heap leaching technology improvements, coupled with deregulation of the gold price, so I ventured off to work in the gold industry with a (then) junior Canadian company called Barrick at a new acquisition of theirs known as Goldstrike. That same gold surge was causing a shortage of iron ore mining engineers in Australia. So after a few years in Nevada, I uprooted the family and left for a little town in the Pilbara of West Australia, known as Newman, to work in the iron ore industry with BHP Iron Ore. An initial short overseas posting turned into six plus years before transferring to BHP’s Indonesian steam coal mines in Kalimantan on the island of Borneo. BHP was going through a rough period following some ill-fated projects (Magma Copper purchase, Beanup and HBI) and was reviewing assets and staffing, so internal opportunities became scarce. Employees were encouraged to “leave the company and find work elsewhere.” So, off I went to Argentina to try copper mining in the Andes with Minera Alumbrera. This short stint in South America was followed by a move to another mining town, Morenci, AZ, and a posting with Phelps Dodge (now Freeport- McMoRan). After 12-plus years without living close to snow, we moved to the Denver, CO area in a new position with Newmont Mining Corp. Along the way I became a professional engineer (Nevada) and completed a masters in project engineering and management. After 11 years with Newmont, I moved to Butte, MT where I accepted a position as assistant professor of mining engineering."

Jan 1, 2015

By Robert L. Major

The expanded role which coal has been assigned in the energy future of the United States has raised numerous policy questions. The very complexity of these questions makes them suitable to analysis by econometric models. However, as the Wall Street Journal indicated in its recent article, business' success with such models have been mixed. I have been asked to present my views as to how coal producers can use such models and in what ways the industry is likely to be impacted by such models. I do not presume to speak for the whole coal industry, but only to share with you the personal observations of one who has worked "both sides of the street", having been employed' both by government and a consulting firm prior to joining the coal industry. In my opinion, the use of econometric models to analyze the coal industry will impact the coal producers in two main ways. First, their use by government will have a profound impact on future government policies related to the mining, transportation and utilization of coal. Second, such models, when properly calibrated and refined, may become useful tools for the coal producers in doing market research and long-range planning. While the former has already begun to impact on the operating environment or the coal industry, the latter is still in the embryo stage.

Jan 1, 1977

By T. Reed Scollon

Before we can attempt to answer the question of what can be expected from coal research, let us examine why research is done in other fields and what others expect for the money they spend on research and development. Up to 1900 almost all organized research was carried out at universities. Most of the support came from the university, and by present standards the amount of research was extremely small. The motivation for university research was basically discovery of new phenomena, with the objective of advancing knowledge. Side by, side with this organized effort was that of individual inventors who were primarily responsible for applying this new-found knowledge to useful purposes. During this period inventors were rarely supported by anyone, and experimentation was carried out either in their spare time or at the expense of earning a living. Men like Edison, I believe, were the first to demonstrate on a large scale that one could systematically apply newly discovered scientific principles to inventions that would serve useful purposes and would return a profit to those engaged in the effort. The tremendous expansion in research therefore began with the realization and demonstration that the scientific discovered could be applied in such a way as to return a' handsome profit to those who invested in it. The motivation of many of the research personnel however, remained the satisfaction associated with new discoveries, The money to support their efforts came from those interested in a return on their investments. Since the First World War and a rapidly accelerating rate since the Second World War another important motive for supporting research has appeared--the needs associated with national defense; this type of research has been supported almost exclusively by the Government.

Jan 1, 1959

By Jim V. Rouse

The decision to hold parallel conferences dealing with hazardous waste and mining waste grew out of the conviction that there were advantages to having personnel serving the two groups talk to each other, as both groups develop cost-effective and environmentally-protective solutions to present and future waste-disposal problems. There has been a certain amount of "reinventing the wheel" which could have been avoided by a better dialog between the two groups. The intent of holding the two parallel conferences is to allow for networking, to minimize future needless redundant effort. The opening session panel speakers represent expertise from both industries; I feel honored to speak as one with a history of serving both groups as a specialist in the subsurface behavior of heavy metals.

Jan 1, 1991

By Simon J. D. Cox, Nicholas J. Archibald, Steve Nichols, Peter B. Ketelaar, Donelle C. Davies, William L. Power

In the mining industry, there is a critical need to communicate complex, three dimensional information about the geology, ore reserves and development plans for mining operations. This information has to be communicated to a diverse audience, the members of which may not be trained in all of the disciplines required to create, utilise, or interpret the information. Software developed to support World Wide Web (WWW) activities has the potential to improve and change the way exploration and mining data and in- formation is organised, presented, and processed. In this paper, we discuss the creation of interactive displays of complex three dimensional data for the mining industry.

Jan 1, 1996