Search Documents

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results from the investigation of the application of thermal fragmentation in Australian hard rock underground narrow-vein mining. Two geologically similar samples from an underground narrow-vein hard rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method. Particle size distribution showed a higher generation of fine product, − 2 mm, by thermal fragmentation compared with selective blasting by 31%. The Bond work index for thermal ore (12.62 kWh/t) is half to that of the blasted ore value (25.32 kWh/t). The average grindability obtained for the thermal ore sample was greater than the blasted sample by a factor of 2.44, a higher value indicating a decrease in the energy required to grind. The thermal fragmentation method generates product with higher dissolution of gold in cyanide, by 14% for the − 9.5 + 2 mm size fraction samples. Additionally, the thermal fragmentation results in higher production of − 9.5 + 2 mm material by 15 % compared with selective blasting.

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results of an investigation of the application of thermal fragmentation in Australian hard-rock, underground, narrow-vein mining. Two geologically similar samples from an underground, narrow-vein, hard-rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method.

Thermal pretreatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The effect of pretreatment using conventional and dielectric heating followed by quenching on the fracture properties of a number single and multiphase brittle materials has been investigated. The reduction in the impact fracture energies and particle strengths with and without pretreatment has been measured in precise single-particle experiments using the Ultrafast Load Cell. Variations in the fragmentation pattern caused by different pretreatments were assessed by measurements of the progeny size distributions. The differences in the effect of thermal treatment on single and multiphase materials are discussed based on the experimental results.

Jan 1, 1995

By William M. Turner

Thermonics is a methodology of ground-water flow system analysis based upon the distribution of heat within the subsurface as influenced by moving ground water. Thermonics is based upon the Stallman Equation 1 (1) which describes the simultaneous transfer of heat through a porous medium which contains moving ground water. The Stallman Equation is:

Jan 1, 1980

By Liyan Ren, Huayang Dai, Yingcheng Li, Enquan Wang

"Three-dimensional geological modelling of coal mines is critical to the sustainable development of the mining industry. On the basis of comprehensively analyzing 3D geological modelling methods, according to the available data of mine such as geological terrain maps, cross-sections and boreholes, we present a 3D modelling method by integrating ArcGIS and 3D GeoModeller. Our motivation is to integrate the advantages of both software modules in processing, converting, integrating and transferring geological information. Special attention has been given to the data structure and processing flow. We build a 3D geological model of the Xieqiao coal mine and successfully extract the geological framework of the strata in the 11118 workface, which is consistent with that of the actual explored geology.Introduction/Background Pertinent impediments such as a lower information degree, the out-of-date information infrastructure and the low level of information management and decision-making make it critical for there to be improvements in mines. Modern exploration technologies favour the construction of digital mine. Digital mine promotes the transformation of the mining industry by integrating information, automation and intelligence to build safe, efficient, high-yield, green and sustainable mines. Three-dimensional geological modelling and visualization of mines are at the core of digital mine. Compared with traditional 2D geological data, 3D models express the various geological phenomena completely, as well as reproduce the spatial distribution of geological units quickly, allowing for the prediction of mining subsidence, better decision-making and improved geological analysis. Modelling methods such as multi-DEM, tetrahedral grid and the generalized tri-prism that are based on borehole estimation and interpolation data are used to construct 3D models of mine geology (Chen 1995,Wang et al 2003, Wu 2004a); nevertheless, these methods cannot fully use multi-source mining data, whereas multi-source integration methods can be used to build 3D models (Kaufmann and Martin 2008, Zhao et al 2009) but require user interaction in model construction and low automation in model updates. During coal production, a plethora of geological data is accumulated. The organisation of discreteinformation under dynamic conditions and the extraction of meaningful information to better service for three-dimensional modelling is a meaningful work (Wu et al 2004b)."

Jan 1, 2017

By D. W. Park

Longwall mining is popular in underground coal production in the United States due to higher production rates and safety concerns. Because of the extreme complexity, it is necessary to plan an adequate design to achieve a safe and efficient working place. The proper sizes of yield and abutment pillars and panels can be determined by simulation using numerical modeling techniques. By means of three-dimensional modeling, stresses to be imposed on the pillars, panels, gob, and powered supports can be analyzed. In this study, an initial three-dimensional finite element model was developed and then modified into four different models. Using these models, the numerical outputs of distributed stresses on three different sizes of yield pillars, three different sizes of panels, and two different sizes of abutment pillars were compared and analyzed to determine the most adequate pillar and panel sizes. Progressive failure theory based on the Hoek and Brown failure criterion was used to determine redistribution of stresses in the yielded and failed areas in the longwall mine.

Jan 1, 1992

By R. D. Hammett

This paper describes an investigation that MS carried out using the three-dimensional, stress analysis computer program "NFOLD" to assess pillar stability in relation to existing mining conditions and the proposed layout of future stopes. The stress analyses were designed to assess the present stability of the mine (particularly the pillars adjacent to the shaft), the change in pillar stresses as mining proceeds, and the optimum stope geometry to minimize ground control problems. The existing conditions were modelled first, and rock mass strengths were adjusted until a good agreement between the predicted and observed conditions was obtained. Analyses of alternative mining layouts, based on the calibrated rock mass strengths, were then compared. The paper describes the results and the conclusions of the study.

Jan 1, 1983

In underground coal mining, one of the biggest challenges is spontaneous combustion, which will not only present safety hazards but result in reserve losses as a result of burnt coal. The released heat coupled with other combustible gases commonly encountered underground will significantly increase the risk of explosion. In this paper, three-phase foam as an environment-friendly fire fighting agent composed of nitrogen, water and fly ash is introduced. The nitrogen facilitates inertization of the fire zone; the water helps cool down the fire and the fly ash can closely cover the coal to isolate the oxygen. What's more, the fly ash and the foaming agent are good free radical absorption. The comprehensive merits mentioned above make three-phase foam quite effective in quenching spontaneous combustion. Experiments indicate that three-phase foam can significantly slow down the temperature rise of coal during oxidation. The comparison between slurry and three-phase foam shows that the latter one is capable of flowing upward in the porous media so as to extinguish the high-point fire and concealed fire.

Jan 1, 2011

By Thomas J. Crocker, Douglas B. Uthus

Tunnel Boring Machines (TBM) have gained worldwide acceptance in the construction field and are being employed in ever increasing numbers to drive underground transit lines, drainage systems, etc. However, TBM utilization in the mining industry, and more specifically coal mining, has been very limited. This paper reviews past and present applications of TBMs to coal mining and examines the needs of the industry in an attempt to offer some insight as to what a TBM system must provide if the excavation potential demonstrated in civil works projects is to be realized in coal operations. EUROPEAN EXPERIENCE Germany The Germans recognized long ago the potential of mechanized drivage for coal mine entry development. Early in the 1960's experimental runs were made with a full-face Wohlmyer roadheader at the Westerholt Mine and trials were conducted on a roller bit armed full-face Bade roadheader. But because of problems with penetrating the various carboniferous strata occurring in changing sequence and hardness, these first attempts were soon terminated. After viewing later successes in the construction industry with improved TBMs, new attempts were initiated by the German mining industry in 1971 to mechanize drivage of their development entries. Four TBMs of two different types were placed in operation.

Jan 1, 1976

By J. Franko, M. S. Klima

Wet-drum magnetic separators are used extensively for upgrading iron ore and for magnetite recovery in dense-medium separation circuits. In this study, the performance of a continuous, laboratory wet-drum magnetic separator was evaluated both with and without the application of ultrasonic energy when processing dense medium slurries. Test variables included magnetic-to-nonmagnetic ratio, solids concentration and nonmagnetic material. The results indicate that, under certain conditions, the purity of the magnetic material increased after ultrasonic treatment. Key words: Ultrasonics, Wet-drum magnetic separation, Iron ore

Jan 1, 2003

By L. Franko, S. Klima

Wet-drum magnetic separators are used extensively for upgrading iron ore and for magnetite recovery in dense-medium circuits. In this study the performance of a continuous, laboratory wet-drum magnetic separator was evaluated with and without the application of ultrasonic energy when processing dense medium slurries. Test variables included magnetic-to-nonmagnetic ratio, solids concentration, and nonmagnetic materials. The results indicate that under certain conditions, the purity of the magnetic material increased after ultrasonic treatment.

Jan 1, 2001

By N. Akbulut, A. Anani

From the initial planning phases to the closing of a mine, mining is an industry where high attention, care, and sensitivity are needed in every step of the mine life. Since mining projects have a long-life span, exceeding a decade sometimes, managing a whole mine project is challenging, especially when challenges faced due to generational differences are considered, such as tracking and logging data, or the usage of different engineering solutions change over time. Along with the overall hardship caused by the time put into a mining project, the present-time operations are very costly where each minute counts. In present-time operations, every decision made, and every minute used during planning and operations has an impact on the efficiency, safety, and economics of the project. Having extremely harsh conditions in both the excavation and mineral processing operations not only slows down the processes but creates very dangerous environments that need to be handled with precise safety measurements. To support the already established processes, we could implement new technologies and use them to our advantage. Virtual reality (VR) is one of these technologies that we could implement in the mining industry. VR is a technology that emerged in the 1960s creating virtual environments and platforms. The user experiences these virtual environments from head- mounted headsets to rooms with 360 screens, all with different levels of immersion. These higher levels of immersion, create a higher level of presencemaking the users more engaged in the activity they are trying to accomplish. These two factors of immersion and presence are what make VR unique and beneficial. VR has some applications and case studies in the industry along with some research being conducted in universities. Unfortunately, there has not been a comprehensive literature review or analysis regarding only VR and its implementations for the mining industry in the last 5 years. This paper aims to describe what VR is and its relation to the mining industry, in the most recent years. The paper first gives a brief background on what VR is and its key concepts. Secondly, it will give information on how the initial stages of the literature review were conducted and the findings along with discussions. The paper will finish with the conclusion drawn from the discussion and potential future work.

Feb 1, 2023

By Ian M. Loomis, Malcolm J. McPherson

A fuel-rich fire exists when the quantity of fuel exceeds the oxygen available to support complete combustion. The transition of a mine fire from Oxygen- rich to Fuel-rich combustion, at this time, represents a point-of-no-return in the fire fighting efforts. Once the transition has been made to fuel-rich the fire can spread at a rate 6 to 10 times as fast as in the oxygen-rich state. Utilizing available technology the fire fighters are left to seal the fuel-rich fie as the only technique to extinguish it. In order to minimize the devastating effects of a fuel- rich fire it is important to understand the means by which the fire becomes fuel-rich and by what means the fire may be returned to an oxygen-rich state. This paper covers: the development mechanism of a fuel- rich fire in a coal mine entry and the physical and chemical effects of applying water to a fire. Experiments concerning these matters have been conducted in a 30 cm square wind tunnel constructed at the Virginia Polytechnic Institute and State University as a model coal mine entry. This paper also addresses the results obtained in testing application of a water mist to fuel-rich fires in this model. These tests have centered on the development profile of a fuel-rich fire in a duct and demonstrate a means of regaining control of a fuel-rich fire by returning it to an oxygen-rich state.

Jan 1, 1995

By Huayang Luo, Hui Li, Wei Zhou, Gang Chen, Scott Huang

The beach and offshore gold resources demonstrated at Nome, Alaska are some of the richest found in Alaska. They contain potentially significant resources that may be exploited in the future. Several companies have contributed to the exploration and reserve estimation in Nome offshore gold deposits. More than 3,000 holes were drilled and over 10,000 offshore samples were analyzed in the Nome offshore areas of approximately 40 km2. Those 3,000 plus drill hole logs were converted into digital formats comparable with ArcGIS software. Considerable amounts of mineral resources data were processed and visualized using ArcGIS 8.3 and its geostatistic, 3D analysis, and spatial analysis components. In this study, based on the data processing and visualization results of ArcGIS, a user-friendly website for mineral resource management and utilization is developed using ArcIMS 4.0.1. ArcIMS is a GIS solution to build and deliver maps, data, and tools over the Internet. The Nome offshore mineral resources website presents the geostatistic and GIS analysis information. This site allows clients to access the information and perform ArcGIS analysis, such as interactive data query, and map layers display of the gold resource distribution, average grade, gold reserve, and relative mineral resource estimation via remote computers. With linkage to other related mining web sites, this web site allows users to search for related publications and more flexibly manage the information. A few other appropriate customized tools are also being developed to assist interactions between the server and clients for data analysis and management.

Jan 1, 2005

By Tim Wolf

The paper "Weld Notch Affects on Pulley and Belt Conveyor Reliability" has done an excellent job of describing theoretical fatigue and fracture mechanics methods used in modern weld design. From this foundation, we intend to further detail areas previously discussed and present new research in the application of these principles to pulley weldment life prediction. Affects of changes in alternating stress range, mean stress, and residual stress have been investigated using controlled laboratory fatigue tests on a pulley weldment. Comparisons between these results, weld codes, and theoretical fatigue predictions will be made and discussed.

Jan 1, 1998

By D. Bogh

Wound rotor motors are used in difficult mining applications where there is a need to start high inertia, hard starting loads while limiting inrush current They are recognized as robust and simple to control. This paper will cover the performance, specification, and important issues to be considered when applying medium voltage wound rotor motors in mining applications. Medium voltage grinding, crusher, and conveyor applications will be discussed. Specifically covered are motor efficiency, speed range, and rotor control. Crane motors often have wound rotor construction, but their load cycle and ratings are outside the scope of this paper.

Jan 1, 2011

By Bruce W. Cavender

In an effort to lower production costs and improve profitability, mining companies have adopted a variety of management practices emphasizing productivity and cost containment. One set of practices that has been used successfully in the manufacturing and electronics industries is "world-class manufacturing" (WCM). It is applicable to mining as well. World-class manufacturing is based on the twin concepts of "just-in-time" inventory practices and total quality control. A few mining companies have implemented quality control programs that are similar to WCM in some ways and substantially different in others. This article considers the use of WCM in the processing environment, although the techniques are applicable throughout a mining operation. The article is also mindful of the variety of customers to whom mineral products are sold. Industrial minerals producers may sell brand-name products to specific customers with exacting requirements, while metals producers often sell their fungible output on a faceless commodity market. Customer requirements are emphasized in WCM, and so the range of these requirements must be recognized. World-class manufacturing In any milling process, specific goals are set for product and process characteristics - concentrate grades, minimum daily throughput, moisture content, etc. WCM has two overriding objectives: the reduction of deviation from these standards, and the reduction of variability in all aspects of the process and product. By definition, reduction of deviation also includes minimizing plant downtime for repairs or process changes. WCM plants use just-in-time inventory practices and total quality control. WCM plants use these techniques to simultaneously improve productivity and reduce costs.

Jan 1, 1993

By T. Negeri

The simultaneous use of two or more families of collectors can sometimes improve one or more key flotation performance indicators, especially if the ore under consideration contains several minerals bearing the same metal. The maximum amount of collectors that can be used is limited by the need to maintain a high concentrate grade and selectivity. Therefore, when more than one collector is required, an experimental design that allows variations of both the proportions and the amounts with respect to other process factors has to be selected to find the optimum dosage. This type of design is known as "process factors in mixture amount experiment". It is a powerful design suitable for discovering the existence and evaluating the magnitude of the interactive effects between various flotation parameters. This paper elaborates the principles on which such a design is based, and demonstrates its usefulness with a case study.

Jan 1, 2003

By David J. Kruse

The proper modeling of granular flow using discontinuum mechanics has the potential to be one of the most significant scientific advancements in the mining industry today. This paper will examine the status of discrete element technology, specifically focusing on current and future applications. The fundamentals of the Discrete Element Method (DEM) will be briefly introduced, as well as relevant design parameters. Various types of granular flow problems currently being solved using the DEM methodology will be presented. The results and potential benefits of these cases will also be discussed. All simulation results and figures used throughout this paper are from studies and designs preformed by the DEM group at Conveyor Dynamics, Inc. (CDI).

Jan 1, 2000

By G. L. Ploetz

The lanthanon compounds are becoming increasingly more important for ceramic and allied applications. As the supply increases and the cost decreases, further development of these interesting materials will undoubtedly lead to new applications and an increased demand. Recent improvements in separation processes have lead to high purity in the individual lanthanon oxides. This report includes short discussions on the mineralogy of the ores as raw materials, and on the separation processes required to produce the pure individual lanthanon oxides in useful quantities. To discuss the presently known applications of lanthanon oxides, this general review is divided into the following categories: A. Glasses, Glazes, and Porcelain Enamels. B. Refractories and Abrasives. C. Electronic Ceramics. D. Nuclear Ceramics.

Jan 1, 1960