Search Documents

By John B. Wright

This paper describes laboratory techniques and subsequent results of Bureau of Mines research to produce chlorination-grade feedstock from an abundant, low-grade, domestic, rock ilmenite ore. The research is part of the Bureau-effort to devise technology that may help decrease U.S. dependence on imported raw materials. A rock ilmenite containing about 46 wt pct Ti02 was smelted in an electric arc furnace with coke, woodchips, and Na2C03 to separate most of the iron as pig iron and to form a low-iron, titanium-enriched slag. The slag was ground, pelletized, oxidized, and then sulfated with mixtures of SO2 and air in a continuous 4.5- to 9.1- kg/h apparatus at 1023 to 1223 K. The sulfated slag, containing 60 to 65 pct TiO2, was reground and leached in water at ambient temperature to decrease the combined levels of the troublesome Ca, Mg, and Mn impurities from 7.0 to 1.7 wt pct. At levels of more than 3 wt pct, these impurities contribute to operating and disposal problems, The final product was upgraded to about 84 wt pct TiO2. This material potentially is suitable for chlorination in a fluidized-bed reactor. The most favorable results were achieved with leached slag sulfated at a feedrate of 4.5 kg/h and at temperatures of 1073 to 1123 K.

Jan 1, 1984

By Håkan Stille, Jalaeddin Y. Rafi, Fredrik Johansson

"INTRODUCTIONIn tunneling projects, pre-grouting is performed with the purpose of establishing an impervious zone around the tunnel periphery. This is obtained by reducing the penetrability of the most conductive fractures in the rock mass. The main attention, besides economy of the project, is given to limiting the ingress of water into the tunnel to a certain amount during construction s well as operation period. Failure in pre-grouting process may, according to Bruce (2007), significantly affect the project in terms of safety, performance, cost and time. In this respect, determination of design parameters (pumping pressure, properties of the mix and stop criteria) affects these projects significantly. In current practices, depends on the geological conditions and requirements of the project these parameters differ widely. Weaver (1991) recommends selection of design parameters, specifically grout injection pressures, based on site specific factors and the conditions at each specific hole into which grout is to be injected (grout hole logging and water pressure test data). Houlsby (1990) correlated the allowable grouting pressure to the quality of the rock mass and the rock cover above the grouted fracture. In his methodology, grouting should be continued until the maximum pressure was attained. Later, Lombardi and Deere (1993) introduced the Grout Intensity Number (GIN), which limits the combination of injection pressure and injected grout volume in order to control the energy induced in the fracture i.e. avoid fracture jacking. Even though the GIN method was a step forward in understanding of the mechanism of the fracture deformation, there are ambiguities connected to this methodology, thus determination of the intensity number is challenging (see e.g., Rafi and Stille 2015)a.A main problem when no theoretical solution is practiced is that effects from the chosen injection pressure, such as possible increases of transmissivity and changes in total grouting time, remains hidden in the overall grouting process. The question is if a high or a low pressure should be used to fulfil the requirements of the projects at the lowest possible cost."

Jan 1, 2016

"INTRODUCTION Foam, unless intentionally created, in any industrial process presents operational problems, or at a minimum, is a nuisance. Some foam problems are unique to a given industry and others are common across many industries. A few problems foam presents to any particular industry are: (a) Poor Housekeeping, (b) Environmental impact, (c) Safety Hazards, (d) Slower Production Rates and, (e) Reduced quality of the end product. Defoamers address these issues. Sadly, the assumption in most industries is all defoamers are alike. In reality, a lot of chemistry is involved in the manufacture of even the simplest defoamer sold today and rarely are any two defoamers “just alike”. Today’s defoamers can include polymer chemistry, fatty esters, alkoxylated alcohols, silicone chemistry, silicone surfactants, ethoxylated and propoxylated block polymers, and a tremendous amount of emulsion chemistry just to name a few. This paper will discuss the various types of defoamers, defoaming mechanisms, the advantages and disadvantages of defoamer selections, and how to choose the proper defoamer for your application. Before a discussion of defoamer can be brought about, foam generation and composition must be discussed. WHAT IS FOAM? Foam is a colloidal suspension of a gas dispersed in a liquid. Most often foam consists of air dispersed in water. If a stream of air is introduced into a liquid, the bubbles produced assume a spherical shape. As the density of the bubble is less than the liquid the bubble rises. When the individual bubbles reach and pass through a surfactant free liquid they collapse. Air from the bubble dissipates and the liquid previously surrounding the bubble flows back.It should be noted a pure liquid will not foam. In the case of air dispersed in water a surfactant is necessary to make the water support a stable foam. A surfactant is a term used to describe a surface active agent; a compound with a hydrophilic end and a hydrophobic end on the same molecule."

Jan 1, 2016

By Mark William Johns

Carbon-in-pulp (CIP) is the preferred method of gold recovery om cyanided plp. However, other gold adsorbents (namely, ton-exchange resms) are being introduced to the industry as they are considered to have several advantages over carbon for the recoery of gold. A set of test methods have been developed by the industry to evaluate the quality of different carbons. owever, many ?f these tests are not applicable to evaluating ton-exchange resms. Hence, a need has arisen for a method to evaluate the different adsorbents. This paper introduces a philosophy to evaluate an adsorbent that results in an estimation of the capital cost and the operating cost associated with the adsorbent. Tests that have been devel­ oped to evaluate the ability of an adsorbent to adsorb gold (in­solutton . counter-current) and to evaluate the optimum adsorbent for a specific pulp (in-pulp batch) are introduced. A method of converting the test data into an economic dimension is present­ed. Case studies are presented to highlight the discussion.

Jan 1, 1996

By Hans Hamrin, Bruce Kennedy

Once an ore body has been probed and outlined, and sufficient information has been collected to warrant further analysis, the important process of selecting the most appropriate method or methods for mining can begin. At this stage, the selection is preliminary only, serving as the basis for a project layout and feasibility study. Later, it may be found necessary to revise the details, but the basic principles for the ore extraction should remain a part of the final layout. With respect to the basic principles employed, relatively few mining methods are used today. For the purposes of this presentation, the principles are classified as follows: 1) For naturally supported stopes, the available methods are room-and-pillar mining and sublevel stoping. 2) For artificially supported stopes, the available methods are shrinkage stoping, cut-and-fill mining, square-set mining, and longwall mining. 3) For caving methods, the available techniques are sublevel caving and block caving. Due to the uniqueness of each ore deposit, the variations on each of these methods are nearly limitless. It is impossible to include even the major variations in this chapter; the goal of this chapter is to present the principles as a guide to the mining engineer in adapting the general methods to specific needs. The selection process described herein is intended to supply the techniques by which the candidate methods available for a given ore body can be reduced to one or two feasible approaches. The feasible approaches then can be evaluated in detail, and the particular modifications can be investigated. In describing costs and economic factors, all values herein are expressed in terms of 1978 US dollars.

Jan 1, 1982

The main goal of this paper is to present readers with recommendations for choosing coaxial cables appropriate for mining applications of Time Domain Ref 1 ectometry (TDR) to monitor rock mass movements. Prior to discussing the recommendations, mining applications are illustrated with examples and the operating principle of TDR is discussed briefly. Items that affect the result of the monitoring system performance include the coaxial cable selected, the grouting material used, and the installation procedure.

Jan 1, 1986

By William Gleason

"There are signs that the commodity downturn that has battered the mining industry for the past five years is beginning to ease up. As the dust begins to settle and mining companies begin to take stock of the battle, Newmont Mining Corp. will be one that is standing strong with just a few scrapes and bruises thanks in large part to the leadership of president and chief executive officer Gary Goldberg and his right hand man and chief operating officer, Chris Robison.As he closes in on retirement (for a second time) Robison, a third-generation miner from Nevada, took time to speak with Mining Engineering about a 33-year career in which, among other things, he is credited with not just helping Newmont survive the turbulent times but with steering the company to a safer, more productive and more profitable heading.“I think we did it better than anyone else,” Robison said when asked how the company fared during the past five years. “We didn’t talk about it a lot, we just put together a strategy and we delivered.”What Newmont, the world’s second-largest gold mining company by production, delivered since Robison took the position of chief operating officer in 2013 are improvements in costs, porduction, projects and safety.Operating under the mantra of “live within your means,” Robison was pulled out of retirement from Rio Tinto and into a challenging situation at Newmont. The price of gold was in a nose dive from a high of nearly $58/g ($1,800/oz) and heading to levels closer to $38.60/g ($1,200 oz).“Newmont is a big ship that can’t be turned, but has to be steered,” said Robison. “We recognized that we had to set a new course. The direction the ship was going was great for $1,600 to $1,800/oz gold but we were chasing ounces.”Like the rest of the gold mining sector before the falling gold prices, Newmont was focused on volume and was looking for gold wherever it could be found. The slogan at Newmont in 2011 was “7 million ounces a year by 2017.”When Robison came on board it was a different reality.“We had to begin focusing on value over volume as the cornerstone of Newmont going forward,” he said."

Aug 1, 2016

By John F. Papp

Chromite is used both as a metallic and nonmetallic mineral. Chromite ore is used as the source of chromium by the metals industry and is used, without chemical alteration, in the refractory and foundry industries. Chromite ore is also the source of chromium for the chemical industry. On average worldwide far more chromite ore is used by the metallurgical industry than by any other industry. Thus, although the primary purpose of this chapter is to describe the nonmetallic uses of chromite, the metallurgical uses must also be discussed in order to provide a complete description of this commodity.

Jan 1, 1994

By A. Acar, E. T. Tuzcu, Y. O. Vural

"In order to sustain the operations in chromite processing plants, due to concentrate selling cost, plants are in need of optimization in terms of capacity and recovery increase. In this study, DAMA Engineering carried out a methodological study for the purpose after a detailed sampling campaign in a plant which is situated in one the main chromite zones in Turkey; 1 The current status of the plant was investigated quantitatively with the bottlenecks, Plant overall efficiency in terms of recovery, Efficiencies of the particular equipment (mill, screen, gravity circuit), 2 A new circuit was proposed with the available equipment, 3 The new circuit that is product of modeling and experimental effort, was evaluated quantitatively as if it is a running plant, After 4-5 months continuous effort, the capacity of the plant was almost doubled (37 tph to 70 tph) and the plant overall recovery was increased from 48% to 63% by grinding adjustments and additional shaking tables theoretically. It was shown that the plant may move into profit with the minimum amount investment using readily available system. INTRODUCTION TO THE CURRENT PLANT The objective of the study is to increase the capacity and recovery of the chromite plant owned by Kurmel Group, Akmetal Inc. The complete study is given elsewhere (DAMA, 2016). The plant is situated in one of the main chromite zones in Turkey; Aladag. The current capacity of the plant is around 35 tph and the overall recovery declared by plant engineer is around 47 %. The chromite plant mainly has 3 units; crushing, grinding and gravitational circuits. The crushing circuit has 3 stages; a jaw crusher, a secondary cone crusher and a tertiary cone crusher operating in closed circuit with a vibrating screen with the aperture size of 15mm. In grinding circuit, a rod mill (2.44 6m x 3.6) and a ball mill (2.13 x 2.3m) are used for primary and secondary grinding, respectively. Derrick screens are used for the size separation. Additionally, for the size classification of the system, hydrosizers are used and each size fraction is sent to the shaking table sets. The middling product of the tables is subjected to re-grinding with a ball mill with the dimensions of 2.1 x 2.9 m. The capacity and the recovery are affected by several bottle necks; hydrosizers’ pure classification, primary/secondary mill power vs capacity problems, re-grinding product’s high slime content and so on. These combined factors made the plant to run in low recovery and capacity. Hence, DAMA was asked to make a study to investigate current status of the plant and propose a new solution to increase capacity and recovery of the plant. The conceptual flowsheet of the circuit is given in Figure 1 below."

Jan 1, 2017

By Charles J. Johnson

The United States is totally dependent on imports for all primary chromite and most ferrochrome supplies. Although the United States imports chromite and ferrochrome from a number of countries, the long-term future of chromite supplies appears to lie in southern Africa (Republic of South Africa and Zimbabwe) where 88 percent of known world reserves exist. Floreover, low mining costs and the availability of low-cost electricity for ferrochrome production gives South Africa a comparative advantage over most other chromite and ferrochrome-producing nations. A well-known problem faced by the United States is that when viewed from a longer-term perspective, the major sources of supply of metallurgical grade chromite and ferrochrome may be subject to disruption. The three countries that have caused the greatest concern have been the Republic of South Africa, the Soviet Union, and Zimbabwe. South Africa presents a particularly difficult problem because it may be subject to internal political unrest and/or U. N, economic sanctions. South Africa has increased its share of world chromium production from about 30 percent in 1968 to 62 percent in 1978.1

Jan 1, 1982

By D. W. Tuckwiller

Electroplating is a widely utilized but little understood process. The fact that the average person is in contact with dozens of plated items daily without even being aware that they are electroplated is evidence of the success of the process. Although a complete explanation of electrodeposition involves thermodynamics and modern theories of bonding and catalytic reactions, in its simplest form the process conforms to the following description. A metal salt dissolved in water partially dissociates into negatively charged and positively charged ions. In the case of nickel sulfate dissolved in water, for example, a portion of the salt dissociates into positively charged nickel ions and negatively charged sulfate ions. If an electrical potential is applied between two electrodes in this solution, the nickel ions migrate toward the cathode and the sulfate ions toward the anode. The negatively charged cathode has a high concentration of electrons, which combine with the positively charged metal ions to form neutral metal atoms with a stable electron configuration. These insoluble atoms thus form a deposit on the cathode.

Jan 1, 1970

The residues produced during the incineration of leather scraps contain significant amount of chromium which can be recovered and reused in the tanning industry. The objective of this study is to develop a cost effective method for chromium recovery from leather ashes produced during the incineration of leather scraps using a fluidized bed incinerator. The entire process investigated involves fusion of leather ash with sodium carbonate in air to oxidise chromium to sodium chromate, leaching with distilled water to dissolve chromates, and chromium reduction from the hexavalent to trivalent state by sodium thiosulphate solution. The main factors affecting chromium extraction, such as temperature, reaction time, and sodium carbonate to leather ash ratio, were investigated. Based on the results obtained, almost 100% Cr extraction can be obtained at 700°C fusion temperature, sodium carbonate to ash weight ratio equal to 3 and retention time longer than 50 min.

Jan 1, 2006

Train services through the Channel Tunnel linking Britain and France where scheduled to be fully restored in February 2009 following several months of repairs after a major fire in the tunnel on Sept. 11, 2008. A lorry caught fire on a shuttle train carrying heavy goods vehicles bound for France through the 50-km- (31-mile-) long northern tunnel. The fire, that spread to other vehicles, raged for about 16 hours. The extreme temperatures of up to 1,000º C (1,832° F) caused extensive damage to about 600 m (2,000 ft) of the 7.6-m- (25-ft-) diameter tunnel?s concrete lining, approximately 11 km (7 miles) in from the French entrance. The Channel Tunnel operator, Eurotunnel, awarded the repair con-tract, estimated to be between ?50 to 60 million, to a consortium of Freyssinet, Eurovia Travaux Ferroviaires (ETF) and Vinci Energies. Freyssinet was appointed to look after the civil engineering works, while ETF would be responsible for track and overhead wire restoration and Vinci Energies responsible for other equipment. The technique of hydrodemolition, which uses high-pressure water jets to remove concrete from various structures, was specified as the method to remove the fire damaged concrete. Freyssinet subcontracted the concrete removal to the specialist hydrodemolition and industrial cleaning contractor Philip Lasserat.

Jan 1, 2009

By Juan H. Rojas

The Chuquicamata mining and metallurgical complex is the main division of CODELCO-CHILE. Its comparative advantage in the world of primary copper producers had deteriorated severely and, consequently, its top management launched an extensive modernization plan. This paper shows how Chuquicamata recovered its position as a low-cost copper producer and is now well positioned to face the end of this century, as far as competitiveness is concerned. It also shows the company's vision for the )(XI century. Given the volume of its ore reserves, one possibility is expanding the sulfide production line capacity, while in the case of the oxide production line, ore reserves are limited so that there is a need to maximize the effectiveness of both organization and technology use. A final consideration has to do with the balance of supply and demand. Most observers of the copper market agree that supply is growing faster than demand. On the other hand, copper is facing severe environmental problems, especially in the piping business, plus the usual threat of substitution. Nevertheless, copper producers are making very weak efforts to defend the market and increase copper consumption through the promotion of new uses of the metal. This issue is crucial and must be considered if copper producers want to maintain a profitable market.

Jan 1, 1998

By Steve Kral

The mining industry has had three difficult years. Commodity prices have remained low and investor confidence in the industry has been shaken. And even though the Asian economy appears to be improving, it will be some time before this improvement will translate into better commodity price conditions for mining. In addition, increased environmental and social restrictions that have been placed on the industry in developed and developing countries have made mining a more difficult proposition. And, if that is not enough, the global mining industry has found itself in fierce competition with Internet businesses for investor capital. Despite that gloomy picture, more than 10,500 mining industry professionals from about 70 countries gathered in Toronto, Ontario March 5-10, 2000 for the Mining Millennium 2000 conference. This meeting was a joint effort between the Canadian Institute of Mining, Metallurgy and Petroleum(CIM) and the Prospectors and Developers Association of Canada (PDAC).The joint meeting also featured two trade exhibitions and more than 150speakers. PDAC’s trade show attracted about 400 exhibitors and an additional 200 in the concurrent Investors’ Exchange. CIM’s exhibition attracted about 600 equipment and service companies.

Jan 1, 2000

The 2003 SME Annual Meeting and Exhibit will take place Feb. 24-26 in Cincinnati, OH. The meeting will feature a host of special symposia and programming geared toward the industrial minerals and aggregate industry sectors. This programming focus is particularly relevant for this annual meeting, as it will be hosted in the center of America’s transportation hub and industrial mineral center. Cincinnati, located on the Ohio River, is key to the movement of America’s supplies and construction material needs.

Jan 1, 2003

By M. J. Virnig, Christopher A. Fleming

THE CIP PROCESS "IN THE RIGHT PLACE AT THE RIGHT TIME? After its tentative introduction to the precious metals mining industry in the earlier part of this century, the carbon in pulp (CIP) process has now come of age, and is the process of choice on all new gold mills. Well over 50 percent of all gold that is mined each year is recovered by adsorption on activated carbon, and the percentage will increase in the years ahead, when old mills using Merrill Crowe technology come to the end of their lives, and as the proportion of world gold production from low-grade resources increases. The pioneering process development work in this field, which was mainly concerned with carbon elution, was carried out by Zadra and his colleagues at the United States Bureau of Mines in the early 1950's (Zadra et al., 1950, 1952), and led to the commissioning of the first large-scale, industrial CIP plant, at the Homestake Mine in South Dakota, in 1973 (Hall et al., 1974). From there, the process spread rapidly, firstly in South Africa in the late 1970's. and then throughout the rest of the gold producing world in the 1980's. There were several factors that led to the meteoric (by gold industry standards) acceptance and successful implementation of this new technology into gold processing operations worldwide. Firstly, and perhaps most fortuitously, the development of the technology closely paralleled the 1968 release of the gold price from the rigid constraints of the $35/oz. gold standard. With the value of the metal allowed, for the first time in modern history, to fluctuate in response to free market supply and demand forces, the gold industry witnessed an unprecedented boom as the price of their commodity increased ten-fold in a remarkably short period of time. This had several important spin-offs as far as new process developments were concerned: The profits realized by established gold-mining companies increased enormously and, consequently, there was more to spend on research and development and exploration for new deposits.

Jan 1, 1993

By Jim Avraamides

The properties of activated carbon which are important for gold recovery applications include activity, capacity, wear resistance, particle size distribution and bulk density. There are experimental difficulties in attempting to simulate the plant environment in the laboratory in order to measure the above properties. However, standard tests can be set up to compare the characteristics of different carbons and to assist in monitoring the performance of carbon in CIP operations. These laboratory tests are critically evaluated and data are presented on the performance of carbon from a number of CIP plants.

Jan 1, 1989

By P. Ollivier

The ore-processing plant of the Soremib mine Pour a (Burkina Faso) has now been in uninterrupted operation for 3 years. Ores from the oxidized and non-oxidized zones of the deposit are processed together in one flotation unit. About 60% of the gold is free and is recovered in a gravity processing unit. The residual gold in the flotation concentrate is processed on the spot by cyanidation and carbon-in-pulp.

Jan 1, 1998

By Markku Virtanen, Pertti Koivistoinen

From the perspective of a large mining company the comminution circuit design is worth keeping within the boundaries of the organisation. The correct circuit design begins from the understanding of the role of grinding. Grinding is a link only in the long "comminution chain," starting from solid rock and ending at the concentrating stage. The final target in comminution is to take a part in the maximization of Net Smelter Return, which goal provides the simultaneous considering of capital costs, operating costs and the economic effect of process results. As a general rule there will be a single crushing stage only, ahead of the grinding process. Grinding does not use any metallic grinding media at all, and there will be fine crushing for critical material in the grinding circuit. Grinding has a minimum two stages, besides, at many concentrators middling products and quite often also tailings are reground.

Jan 1, 1997