Search Documents

By J. C. Schneider, G. Van Weert

Hydrochem Developments Ltd. has developed and put into full scale operation a novel type of vertical flotation column incorporating a multiplicity of mechanically agitated stages. Characteristics of this flotation column include a low height to diameter ratio, high upgrading factors and the possibility of modifying geometry and operation to specific flotation requirements. A commercial unit is currently handling up to 100 tpd rougher concentrate at Dickenson Mines Limited, Balmertown, Ontario. Design parameters and plant performance will be discussed.

Jan 1, 1988

By Per H. Fahlstrom

The story of the Aitik mine begins in the early thirties. At that time blocks of low grade chalcopyrite impregnations were found in Swedish Lapland not far from the present mine, some 40 miles north of the arctic circle in the vicinity of the iron ore field at Gällivare. The ore prospect was viewed upon several times. By means of geophysical studies and an extensive diamond drilling programme during the end of the fifties and the beginning of the sixties a huge low grade ore body was discovered under the muskeg overburden. In 1965 55 million tons of ore with 0.5 % Cu was known to a depth of 160 ft. In 1970 the ore reserves had increased to 165 million tons with 0.40 g, Cu at a depth of 400 ft. Decision to develop the mine and to start production at an annual production of 2,2 million tons was made in 1965. A mine and concentrating plant, the A section, went on stream in 1968. In 1970 decision was made to expand the production with 3,3 million tons pr year. A second section of the plant, the B section, went on stream during the end of 1972 and the beginning of 1973 The production in the initial plant has been increased to 3,1 million tons pr year and during 1974 the combined A and B sections are expected to treat' about 7,2 million tons of ore. The two sections will treat 10,000 and 13,000 tons per day.

Jan 1, 1974

By J. Astier

The idea of using only one strand for both sintering and cooling of the sinter is not new. In 1952, in the U.S.A. a sintering plant was built at Benson Mine (Star Lake, N.Y.), including : - 68 m2 or 735 sqft (8 wind boxes) for sintering, - 22 m2 or 237 sqft (3 wind boxes) for cooling. In the USSR, a large number of machines have been built allowing for cooling of the sinter on the strand, especially the 4 m (about 13 ft) machines, with : 252 m2 sintering grate area 60 m2 cooling grate area 312 m2 total grate area. However, such ventures did not prove very successful, and the IRSID embarked many years ago on a research program to discover : - what are the problems associated with cooling on a sintering strand ; - what are the possible solutions for industrial plants.

Jan 1, 1974

By M. A. S. Martins, J. C. Guillaneau

Steady-state simulation has been proving its usefulness and efficiency in process design and optimization for many years. Steady-state simulation is a very effective approach for plant design since it enables a great number of hypotheses to be considered regarding flowsheet, equipment etc., the processing equipment and material handling equipment to be sized, and the configuration of almost optimal industrial plant to be attained in a very short time. This paper will present the basic principles of mineral process simulation methodology and some real case applications of their capabilities in several complex ores in Brazil.

Jan 1, 1998

By D. Royston, D. Denlay

Pulp lifters are used to discharge ground pulp from non-overflow grinding mills. In straight-radial channel pulp lifters, discharge is often incomplete and back-flow down the pulp lifter can occur. Leading-curve channel pulp lifters can be used to ensure complete discharge, especially at high mill rotational speeds. The complex motion of solid materials in pulp lifters has been modelled mathematically for both straight-radial and curved pulp lifters in order to make comparisons between the two types. The model is supported by practical observations of the performance of curved pulp-lifters in a commercial 24ftSAG Mill as well as observations of the discharge from several commercial straight-radial pulp-lifter AG/SAG Mills.

Jan 1, 1999

By E. F. Draskovich

In 1984 a high temperature heat recuperation system was installed in the pellet plant of the National Steel Pellet Company located in Keewatin, Minnesota. The system is similar to those of Cleveland Cliffs Empire and U.S. Steel's Minntac operations. It recovers hot process air from the cooler by induced flow, and directs it to an intermediate zone between the drying and preheat zones on the grate machine. This system recently underwent further modifications in April 1985, following initial operation in 1984. The M. A. Hanna Company, which manages the property, developed the design criteria and made the subsequent recommendations for modification through its research facility in Nashwauk, Minnesota.

Jan 1, 1986

By L. Sletmoen, P. Rocque, E. DeSouza

Plans for achieving planned production rates at the Red Lake Mine High Grade Ore Zone required that the mine ventilation system be upgraded. Time constraints required that only a site assessment of the mine ventilation system be performed followed by recommendations for providing adequate ventilation conditions at the production zone. This paper describes the engineering assessment, design and commissioning of the ventilation system upgrade for achieving increased flows at the high grade ore zone. The work was successfully achieved with minimal capital expenditures and disruption to the mining cycle.

Jan 1, 2003

By Alfredo Valdivia, Dominic Reda, Vojtech Gall

The design and planning for the construction of a new passageway to improve access and circulation to better accommodate anticipated increased passenger flow within Grand Central—42nd Street Station. The passageway includes the break-in of an over 100-year-old station cavern with an innovative design implementing a protective structure above the existing track to allow for safe train operations and passenger circulation during construction. Construction of the new passageway follows the Sequential Excavation Method. This paper will present the innovative solutions that went into the preliminary design and planning considering construction access, site logistics, risk management, structural retrofitting, instrumentation and monitoring, and impact assessments.

Jun 13, 2023

By L. Gertsch, R. Gustafson, J. Rostami, C. Swope

Development of a permanent human base on the moon for exploration requires a self-sustaining system. Such a system entails the production and processing of limited amounts of raw material on the moon. Any mining and construction activities on the moon can only be performed by a robust excavation machine that can excavate a variety of material, from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, a limited amount of information on lunar regolith is available to develop and optimize a machine for lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe, PA. This paper discusses the results of initial material characterization, as well as full-scale tests of a prototype cutterhead in relevant material. A brief review of anticipated production rates under various assumed ground conditions is also presented.

Jan 1, 2010

Development of a permanent human base on the Moon for exploration requires a self sustaining system. This entails production and processing of limited amounts of raw material on the Moon. Any mining and construction activities on the Moon can only be performed by a robust excavation machine that can excavate a variety of material from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, limited amount of information on lunar regolith is available to develop and optimize a machine for given lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe PA A. This paper discusses the results of initial material characterization as well as full scale tests of a prototype cutterhead inrelevent material. A brief review of anticipated production rates under various assumed ground conditions will also be presented.

Jan 1, 2009

By Joseph Gildner, Donald J. Phelps, Jürgen Laubbichler, Christopher Tattersall, David McAllister

The Beacon Hill Station and Tunnels portion of the Sound Transit Central Link Project consists of one mile of twin rapid transit tunnels, an underground station, portals and ancillary works constructed in an urban environment. Presently under construction, the station will set a number of North American firsts including deepest soft ground excavation carried out using the Sequential Excavation Method (SEM).Located in highly variable glacial soil deposits ranging from soft, water bearing sands to stiff, slickensided clays, the station complex and running tunnels proved to be technically challenging during design. Meeting these challenges necessitated an extensive geotechnical investigation, a trial shaft, and state-of-the-art numerical analyses to develop ground conditioning, pre-support, excavation support and structural design. A comprehensive risk identification and mitigation program, and innovative procurement strategy were incorporated into the design and contract bid documents.

Jan 1, 2005

By AJIT SWAIN, SUNATI MOHANTY

The ability to predict the dewatering performance of an industrial hydrocyclone from a laboratory-model hydrocyclone is of great importance. In this study, laboratory-scale hydrocyclone experiments were conducted using silica sand samples at 10 percent solid concentration for dewatering with Mozley hydrocyclones with diameters of 2 in. and 4 in. The objective is to predict the design parameters for an industrial dewatering cyclone to achieve higher solid concentration in the underflow. A model was developed based on the Nageswararao hydrocyclone model with the help of a commercial simulator for a hydrocyclone operating at 100 t/h and 20 percent solid concentration to achieve 80 percent solid recovery at 45 percent solid concentration in the underflow.

Mar 1, 2023

By AJIT SWAIN, SUNATI MOHANTY

The abstract discusses the importance of predicting the dewatering performance of industrial hydrocyclones from laboratory models. It highlights the challenge of scaling up design and operating parameters for efficiency estimation. The paper describes experiments with a 2-inch and 4-inch hydrocyclone using silica sand. It details the development of a model using the Nageswararao hydrocyclone model and a simulator to estimate model parameters. The model is validated with experimental data, and a new model is developed using 4-inch hydrocyclone data. The technique is then extended to predict dimensions for a full-scale dewatering cyclone operating at higher throughput and solid concentration.

Mar 30, 2022

By Robert H. Merrill

7.1-STABILITY OF SLOPES IN SOIL AND ROCK ROBERT H. MERRILL 7.1.1-DESIGN ANALYSIS APPROACHES The analyses of slopes in soil or rock can be made through application of soil- or rock-mechanics principles. In most cases, the material in the slope wall can easily be identified as either a soil or a rock. However, there will be instances where, because of unique characteristics, the soil may behave as a rock structure, or vice versa. By necessity, these unique cases must be identified through experience or critical observation by the engineer, because there are no definitive rules clearly establishing the differences. The most important step in a solution to a slope problem is to define it. Normally, once the problem is identified, a solution usually can be found or a reasonable estimate obtained. The design analysis of a slope wall implies an evaluation of the stresses or forces in the wall, and of the ability of the material in the wall to withstand them. Therefore, the factors influencing a design analysis can be divided into two categories: those which influence stresses, and those which influence the ability of the wall to withstand stress. For simplification, the latter is termed the strength of the soil or rock. Perhaps the basic difference between analyses for soils and those for rock is in the identification of the failure surface. Soils generally do not have an identifiable failure plane. However, some soil layers in a slope wall may have different strengths. A soil slope wall may consist of a thin layer of topsoil overlying a thick, uniform clay, or a topsoil over a gravel or other materials. Therefore, the soil generally does not have a potential plane of weakness that can be identified through observation. On the other hand, rocks normally contain planes of weakness in the form of fractures, faults, joints, bedding planes or other discontinuities weaker than the intact rock, which can be found through observation and/or tests upon rock samples. If the failure surface cannot be identified, the principles of soil mechanics should apply because, in soil mechanics, the failure surface usually is assumed. If it can be identified, then the principles of rock mechanics should apply. 7.1.2-ANALYSES OF STRESSES OR FORCES IN SLOPES All existing methods of soil-slope analysis are based upon interpetations of the Coulomb and Coulomb-Navier failure criteria, commonly termed the total-stress 2nd the effective-stress criteria (Sec. 6.1). The total-stress criterion may be illustrated by the diagram in Fig. 7-lA, which relates the total stress, S, to the cohesion, c: the normal stress, u, and the angle of internal friction, 9, by the expression

Jan 1, 1973

By R. N. Powell

The Pipeline ore body was discovered in March 1991. The construction of the new mine and mill did not start until early March of 1996. Upon completion of permitting and corporate project approval, the 289 million USD project was “fast tracked”. The commissioning began 11 months after start of construction and the project ended 40 million USD under the budget figure. The objective of this paper is to review and highlight the Pipeline Project history from discovery, design, lawsuits, permitting, and re-design through to current - 1998operating practices. Particular emphasis will review the process design, design mistakes, and design successes. The paper will review project history, feasibility, design concepts, operator training, construction, financial and the current operation. Additional discussion will review what design features worked and which did not work within the process plant.

Jan 1, 1999

By Randy N. Powell

The Pipeline gold ore body was discovered in Lander County, NV in March 1991. Construction of the new mine and mill did not start until early March 1996. The $289-million project was placed on a fast-track development schedule upon completion of permitting and corporate approval. The mine and mill were commissioned 11 months after the start of construction and the project ended up $40 million under budget. Project design and construction management were provided by Placer Dome Project Development Division (PDD). History The Cortez Joint Venture has operated in northeast Lander County since the late 1960s. The business structure is comprised of 60% Placer Dome and 40%Kennecott Exploration. Throughout the years, production has been from several small open-pit deposits— Cortez, Horse Canyon, Gold Acres and now Pipeline.

Jan 1, 1999

By Terry O. Arney

This paper is a description of the digital Data Acquisition and control System that is installed at Cities Service's Pinto Valley Concentrator. Pinto Valley Concentrator ? The Pinto Valley Concentrator (5, 41 is located approximately seven miles west of the town of Miami, Arizona. The Concentrator is situated south of the open pit mine and was designed to process 40,000 tons of ore per day with an average grade of .45% copper. The comminution process consists of primary, secondary, and tertiary crushing, and single-stage closed-circuit grinding 161. Concentration of the copper sulfides is by means of froth flotation. Concentrates are transferred to the Inspiration Consolidated Copper Company smelter in Miami, Arizona through a slurry pipeline.

Jan 1, 1976

By John F. Beesley

INTRODUCTION This paper discusses the design of the subsurface nuclear waste repository at Yucca Mountain, Nevada; and possible concepts for construction of the subsurface facility. Subsurface construction at Yucca Mountain is planned to last for 20 or more years, and may be accomplished using tunnel boring machines (TBM), drill and blast methods, raise bore machines, and roadheaders. The design of the subsurface facility includes approximately 107 km (66 miles) of tunnels and drifts. The vast majority of the repository will be excavated with TBMs. Design and construction concepts for the subsurface repository discussed in this paper are based on the License Application that was submitted to the U.S. Nuclear Regulatory Commission (NRC) by the U.S. Department of Energy (DOE) on June 3, 2008. The License Application was subsequently docketed by the NRC in September 2008. When a Construction Authorization is received from the NRC, notices to proceed with subsurface construction at Yucca Mountain will be issued by DOE. The Yucca Mountain site is located in the Mojave Desert approximately 150 km (90 miles) northwest of Las Vegas, Nevada. The site is on federal land in southern Nevada and is shown in Figure 1. Yucca Mountain is a ridge of volcanic rocks com-posed primarily of solidified volcanic ash. Previous underground construction work at Yucca Mountain included excavation of two tunnels using two different TBMs. The first tunnel, the Exploratory Studies Facility (ESF), is a 7.62 m (25 ft) diameter tunnel that is 7,877 m (25,843 ft) long and was described by Morris and Hansmire at the Rapid Excavation and Tunneling Conference (RETC) in 1995. The second tunnel, known as the Enhanced Characterization of the Repository Block (ECRB), was a TBM drive of 5.0 m (16 ft, 5 in.) in diameter and 2,681 m (8,796 ft) long. The second tunnel was excavated in 1998 and was described by Fulcher, Eastlund and Copeland at RETC 1999 and is named the East?West Cross Drift in that paper. (These previously excavated tunnels are shown in Figure 2.) In the volcanic rock formation where the vast majority of the planned repository will be con-structed, previous tunneling conditions were generally very good.

By E. C. Westman, F. J. Shreve

This paper presents the design and construction of a multi-channel geophone array that improves tomographic imaging capabilities in both surface and underground mines. Especially important in the design of the array is sensor placement. Three issues related to sensor placement are addressed in this paper: 1) sensor placement in long, horizontal boreholes, 2) development of simple, robust, MSHA-acceptable clamping unit, and 3) orientation of the geophones within the borehole. Improved imaging capabilities will produce energy, environmental, and economic benefits by increasing exploration accuracy and reducing operating costs.

Jan 1, 2002

By Belinda F. Arbogast

Reclaimed mine sites have been evaluated so that the public, industry, and land planners may recognize there are innovative designs available for consideration and use. People tend to see cropland, range, and road cuts as a necessary part of their everyday life, not as disturbed areas despite their high visibility. Mining also generates a disturbed landscape, unfortunately one that many consider waste until reclaimed by human beings. The development of mining provides an economic base and use of a natural resource to improve the quality of human life. Equally important is a sensitivity to the geologic origin and natural pattern of the land. Wisely shaping our environment requires a design plan and product that responds to a site's physiography, ecology, function, artistic form, and public perception. An examination of selected sites for their landscape design suggested nine approaches for mining reclamation. The oldest design approach around is nature itself. Humans may sometimes do more damage going into an area in the attempt to repair it. Given enough geologic time, a small-site area, and stable adjacent ecosystems, disturbed areas recover without mankind's input. Visual screens and buffer zones conceal the facility in a camouflage approach. Typically, earth berms, fences, and plantings are used to disguise the mining facility. Restoration approaches the best land use as restoring to its original condition. Rehabilitation targets social or economic benefits by reusing the site for public amenities, most often in urban centers with large populations. A mitigation approach attempts to protect the environment and return mined areas to use with scientific input. The reuse of cement, building rubble, and macadam meets only about 10% of the demand for aggregate. Recognizing the limited supply of mineral resources and encouraging recycling efforts are steps in a renewable resource approach. An educative design approach effectively communicates mining information through outreach, land stewardship, and community service. Mine sites used for art show a celebration of beauty and experience-abstract geology. The last design approach combines art and science in a human-nature ecosystem termed integration. With environmental concerns, an operating or reclaimed mine site can no longer be considered isolated from its surroundings. Site analysis of mine works needs to go beyond site-specific information and relate to the regional context of the greater landscape. Understanding design approach can turn undesirable features (mines and pits) into something perceived as desirable by the public.

Jan 1, 1999