Search Documents

By Tan Zhenxiang

INTRODUCTION Koolyanobbing is an open cut iron ore mine, which is located in Yilgarn region of Western Australia. To prevent the operators from suffering silicosis diseases and protect the air from being polluted, a series of dust control measures have been taken. These measures include ventilation and dust control system for sample preparation shed, dust collecting system for drill rig, dust suppression system for ore processing plant, dust control for haul road. The details related to individual dust control measure are dealt as follows. SAMPLE PREPARATION SHED DUST CONTROL The sample preparation is one of the major dust sources at Koolyanobbing. The activity is being carried out at the sample preparation shed. It typically needs to go through the following stages, that is, crushing, splitting, drying and pulverising. The amount of dust generated from crushing and splitting is mainly determined by the moisture content contained in the pre- pared sample. A significant amount of dust is generated at the sample pulverising stage due to cleaning sample bowl with com- pressed air. To protect the sample preparing personnel's health and make the dust level in the air meet the requirement from the health and safety authority, a central ventilation and dust control system has been installed at the sample preparation shed. As shown in Fig. l, the system consists of suction heads, suction lines, dust collector and vacuum fan. The fan creates vacuum environment in the system, therefore the dust is drawn into the dust collector through the suction heads and suction lines. The dust collector is of fabric filter. When the dusty air comes to the filter, the dust in the air is collected and retained on the surface of the filter while the clean air passes through and enters the atmosphere. The retained dust is blowed out by the pressured air pulses and deposits into the dust bin underneath the filter. A time relay device is used to control the cleaning time and the cleaning interval. DRILL RIG DUST CONTROL A hydraulic percussion drill is used to drill blast holes. To carry out the drilling operation properly and efficiently, the cut- tings are being flushed out of the hole by the compressed air. In order to prevent from the fine particles in the cuttings escaping to the air, a dust collector is attached to the drill. The collector mainly consists of suction head, cyclone and bag filter. Refer to Fig. 2. The suction head is installed at the lower end of the feed beams and is movable. The moving range is up to 250 mm. It is not only used to restrict the cuttings, but also used to prevent water from entering the filters when drilling wet hole. A 406 mm diameter primary cyclone is used to separate the heaviest particles in the cuttings. It is also used as blast holes sampling equipment. One part of the dust particles are collected by a sample bag through a splitter attached to the end of the cy- clone. The rest of the particles fall down to the ground through the closing rubber. The bag filter is driven by a hydraulic motor (1). It is used to collect the lighter particles in the cuttings. The filtering area is 16 m2 and the dust separation efficiency is up to 99.9%. The working principle of the filter is demonstrated in Fig. 3. When the rock drill (9) flushing is turned on, the pressurised air from the compressor is directed to the rock drill and to the pres- sure switch (10). The pressured air will open the pressure switch to de-energise and close the solenoid valve (4) The pressure affecting the cut-off cylinder (5) keeps the exhaust port flap open. When the flushing valve (8) is closed, the pressure affecting the cut-off cylinder disappears and the internal intake opening flap is closed by a spring. The pressure also ceases to affect the pressure switch and the spring switches the contact to the point 2. The time relay (11) is now activated and gives a 0.5 second current impulse to the solenoid valve and keeps the current cut off for approx 8 seconds. When the solenoid valve is live, it opens and lets an impulse of pressured air to the filters (2). These impulses will clean the filters.

Jan 1, 1997

By J. Davitt McAteer

Improvements in the control of coal mine dust have occurred over the past 25 years. Simultaneously, dramatic improvements in coal mine production technology have occurred, particularly at mines where longwall systems are in use. Production rates of longwall systems have quadrupled since 1978, and dust generation on these systems has significantly increased. However, technology to address control of the resulting increased levels of respirable dust has not kept pace, and many high-production longwall sections continue to experience problems with respirable dust control. This paper seeks to enlist the entire mining community in the effort to resolve the health problems presented by excessive levels of respirable coal mine dust, particularly on longwall systems. These systems are expected to increase in number and length, and to generate increasingly higher levels of dust as production rates of these systems continue to rise.

Jan 1, 1995

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with mediumsized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in the present study: a 15.2-cm (6-in.)-wide shelf; a 7.6-cm (3-in.)-wide shelf; and a 7.6-cm (3-in.)-wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1 and 1:1 were evaluated for the 15.2-cm (6-in.)-wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. IntroductionSurface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1 percent of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples).• 5.8 percent of rotary drillers were overexposed to respirable silica dust (nine out of 155 samples).• 7.3 percent of drill helpers were overexposed to respirable silica dust (three out of 41 samples).• 7.5 percent of blasters/shotfirers were overexposed to respirable silica dust (three out of 40 samples)."

Jan 5, 2018

By Welby G. Courtney

Recent field and laboratory results related to the use of water sprays and ventilation in the control of dust at the mine face are presented. Optimization of water sprays for impaction and collection of airborne dust is discussed and guidelines presented. Exhausting versus blowing primary ventilation, dust collectors, several secondary exhaust ventilation systems, and a "throw" technique he discussed.

Jan 1, 1980

By Michael F. Jeglic

Dust control methods are practiced throughout the mining industry in order to protect the health and safety of its workers, the integrity of the environment, and to guard against the loss of valuable product. The use of water is often the best and most economical method of controlling dust. Increasingly, chemical agents are being chosen over more traditional mechanical means of controlling dust. Some chemicals are used alone, and many are used to enhance the dust controlling properties of water. This paper describes the various types of chemicals available and their applicability to specific problems encountered by industry.

Jan 1, 1986

The Mine Safety and Health Administration (MSHA) has conducted studies to evaluate dust control technologies on deep cut continuous mining sections. These surveys have been conducted in different mines using various mining methods, face ventilation systems and dust control systems. The surveys typically consist of respirable dust sampling combined with a time study of mining activities. Measurements of dust control and operational parameters are also made. Critical elements identified for controlling respirable dust in deep cut mining systems include controlling intake dust, dust collector capacity, face ventilation quantities and velocities, positioning of workers, work practices and selection of equipment. This paper discusses how the dust surveys are conducted in deep cut mining sections and how these surveys are used to identify specific dust generating sources.

Jan 1, 1999

By R. A. Jankowski

The US Bureau of Mines (USBM) conducted a series of laboratory tests to investigate the effectiveness of using a flooded-bed scrubber with exhaust ventilation in deep-cut faces. An experimental test program to determine the impact on respirable dust levels resulting from changes in face airflow, curtain-setback distance, operator positioning and operating parameters of the external spray system on the miner was completed. Gravimetric sampling was conducted in the immediate return and at three sampling locations on the off-curtain side of the entry. Statistically significant differences in dust levels, on the order of 0.5 to 1.2 mg/m3, were observed between specific sampling locations and changes in several test parameters. Dust sampling results indicated that a flooded-bed scrubber and exhaust ventilation can be a viable dust-control system for extracting deep cuts up to 12.2 m (40 ft) in length. The impact on methane was not evaluated.

Jan 1, 1998

By R. A. Jankowski

The U.S. Bureau of Mines (USBM) conducted a series of laboratory tests to investigate the effectiveness of using a flooded-bed scrubber with exhaust ventilation in deep-cut faces of up to 12.2 m in length. An experimental test program to determine the impact on respirable dust levels resulting from changes in face airflow, curtain setback distance, operator positioning, and operating parameters of the external spray system on the miner was completed. Gravimetric sampling was conducted in the immediate return and at three sampling locations on the off-curtain side of the entry. Statistically significant differences in dust levels on the order of 0.5 to 1.2 mg/m3 were observed between specific sampling locations and changes in several test parameters. Dust sampling results indicated that a flooded-bed scrubber and exhaust ventilation can be a viable dust control system for extracting deep cuts up to 12.2 m in length. The impact on methane was not evaluated.

Feb 24, 1997

By Henning E. Soderberg, Robert Brien, O&apos

Coal may be the answer to US energy problems, but it also has its drawbacks. If it is crushed, screened, dumped, or moved, the environmental engineer is faced with a dust problem. To control coal dust, at both minimum initial cost and reasonable operating cost, demands a working knowledge of dust control equipment design, as well as the coal handling operation. Here are some guidelines to reduce air volume requirements and cut overall system costs.

Jan 10, 1981

By J. B. Webster

Health and Safety in the work place is of primary concern to the underground coal industry. Control of dust in the underground environment is of major importance in this concern. Utah Power and Light Mining Division has undertaken extensive studies to determine and control the various sources of respirable dust in underground high production sections. Determination of dust sources has been achieved by real-time aerosol sampling and standard gravimetric sampling on individuals and in various suspect locations. Some sources are diesel roadway dust, outby crushing, and handling equipment, face sloughing, water spray roll-back, and mining equipment. Once identified, the dust sources are suppressed or controlled and/or the workers are directed from areas of greatest potential exposure.

Jan 1, 1990

By L. Xu

Since the establishment of the standard dust concentration of 2 mg/m3, a strong effort has been made by mining engineers and researchers to provide better dust control equipment and procedures for underground coal mines. Particular areas of success have been control of dust generation by better coal-cutting strategy, better design of water sprays for dust suppression and air movement, use of scrubbers, and improved design of face ventilation systems. A drastic improvement occurred over time such that the average dust concentrations for continuous miner operators dropped from 6.5 mg/m3 in 1968 to 1.3 mg/m3 in 1980 and for auger, cutter, longwall, and roof bolter occupations from 2.7 mg/m3 in 1973 to 1.6 mg/m3 in 1980 (Niewiadomsky, 1983).

Jan 1, 1990

By Harry Elkin

Control of coal dust has long been an important aspect in the conventional mining of coal; the main reasons being from a health and disaster standpoint. With the advent, of mechanized longwall mining, the control of dust has required more attention due to the high extraction rate common to most longwall systems. The purpose of this paper will be to describe the dust abatement activities of the longwall operation at Sunnyside. Kaiser-Steel Corporation has three mires located at Sunnyside, Utah, with a total production averaging 6,800 tons of clean coal per day. Of this 6,800 tons, 71 % is mined with continuous miners, the remaining 29% coming from one longwall unit located in No. 3 Mine. Our first longwall panel was started in November, 1961. In October, 1966, we started mining our seventh panel. The present panel is located in the Upper Sunnyside Seam which averages five feet in thickness, but does get as low as 51 inches. The seam pitches 5.5% in this vicinity. The roof is generally good and is comprised of 10 inches of shale cap rocs overlain with sandy shale and sandstone. The floor is sandy shale and is quite undulating in nature. The present panel is 3,800 feet in length with a face of 670 feet. The major equipment employed on our longwall unit is a 125 H.F. Anderton Shearer-Loader, British Jeffrey Diamond armored conveyors and a Dowty self-advancing-roof support system. The Anderton Shearer in use on our longwall unit has a 60" diameter x 27" cutting drum. During the shearing cycle, it traverses the face at 20 feet per minute with a cutting rate of 7.5 tons/minute.

Jan 1, 1967

By Carl Heising

Longwall workings in the Federal Republic of Germany are situated in deep depths. Coal deposits are characterized by a sequence of many seams and manifold geological disturbances. Hence result special requirements on the layout of workings, the methods of coal getting, supports, mine ventilation and dust control. As for the application of dust control the large quantities of fresh air and, this, the high air velocity and the limited water contents in the run-of--mine coal must be taken into consideration. The principle of our methods of dust control is to avoid, if at all possible, the development of dust and, if this is not possible, to suppress the dust even during its development. In nearly all coal faces, the method of water infusion prescribed by our Mines Inspectorates is applied. Continuous water in- fusion is preferred. For water infusion in the coal face, intensive developments as to the process and as to the tools and apparates to be applied were done. The German coal mining industry differs between cutting coal getting and stripping coal getting. Water spraying to the tracks of coal ploughs as well as internal and external water feed to the loader required special activities of further development in past years. There are possibilities to still improve such methods in future. A new important field of applying dust control developed from the application of powered supports. In this field, water spraying prevails. Wet methods of dust control are prefered also in the conveying and loading of coal and at through-flow crushers, however, as far as possible, combined with a covering of the working points where dust develops. Devices for the collection and sedimentation of dust, so-called dust exhausters, are used also with crushers In advanced headings, dust control is performed solely by water. Gateroads kept on or behind the coal face line call for new methods of dust control which are at present under development.

Jan 1, 1980

By Y. P. Chugh

Additional field evaluations of a modified continuous miner using a new spray system and modified scrubbers have been conducted by the authors. In this demonstration, a comprehensive package for dust control on a continuous miner which included previously developed modifications to the scrubber, scrubber intakes and the innovative chassis spray system was demonstrated. Side-by-side comparisons of the modified miner and regular miner indicated that the miner operator with the modified miner was exposed to 62% less respirable dust. Ram car operators with the modified miner had 38% less respirable dust exposure and the return air on the modified miner had 19% less respirable dust. The mining conditions during side-by-side testing were very comparable. These results support the findings of the modified spray system studies conducted earlier at different mines in Illinois on four occasions and the modified scrubber system field evaluation studies.

Jan 1, 2009

By W Frint

An area in Southwestern Wyoming is rapidly becoming the soda ash capitol of the world. Starting only 20 years ago from a unique deposit of trona, the out-put has rapidly increased until now about half of the soda ash produced in the United States comes from this area. Chemically, soda ash is sodium carbonate, a large tonnage, widely used alkali. The largest single industrial use is in glass manufacture, where 25 tons of soda ash are used in producing 100 tons of glass. Other big users are the detergent and chemical industries. The trona deposits in the Green River basin of Wyoming, were formed about 75 million years ago as part of a geologic period when an ancient lake alternately went through periods of being a large fresh water or smaller brine lake. Today these deposits lie from 800 to 3000 feet below the surface in a semi-arid, almost desert region just west of the Rocky Mountain Continental Divide at an elevation of 6200 feet. In this area there is a prevailing westerly breeze and almost every afternoon the velocity reaches very windy conditions. Rainfall is minimal, being only 6-8 inches of moisture per year with an evaporation rate exceeding 24-inches. Most of the moisture comes in winter snows or summer thunderstorms. Temperatures are low with below zero weather dur¬ing most of the winter and early morning frost is not uncommon during the summer months. There are many trona beds varying in thickness from a few inches up to 15 feet. The deposits now being mined vary from 8 to 10 feet in thickness. The ore is mined by driving tunnels either via conventional explosives or with continuous boring machines. It is transported to the shafts via conveyor belts

Jan 1, 1972

By R. S. Ondrey

MSHA has prepared two pamphlets that provide guidelines for selecting dust control parameters for underground coal mining sections. These guidelines are based on research conducted by the Bureau of Mines and underground studies conducted by MSHA. One set of guidelines is specific for longwall mining operations. Another set of guidelines covers room-and-pillar operations. The guidelines contain a general discussion on the appropriate use of ventilation and water to optimize the control of dust.

Jan 1, 1995

By Jerry C. Tien

China?s remarkable levels of economic growth during the past three decades have lifted almost 300 million people out of poverty. This amazing achievement has placed an increasing demand on energy and minerals, especially coal, which supplies 68.7 percent of China?s energy (June 2011). It is estimated that China mined more than 3 Gt (3.3 billion st) of coal in 2010, three times as much when compared to merely 10 years earlier. Such an impressive achievement does not come without major costs ?? including concerns with mine safety and an increasing number of occupational illnesses due to fast growth. This article reports on one of the major safety concerns in China?s coal mining, dust and dust control practices, and known cases of caol worker?s pneumoconiosis affiliated with prolonged exposure to excessive coal dusts. The exact size of China?s mining industry is not known, but it is estimated the coal industry is at least five-million people strong, and the metal and nonmetals industry probably employs another three million people. To meet increasing energy demand, China mined more than 3.1 Gt (3.4 billion st) of coal in 2010 from its 15,000 plus coal operations1, most of which are small- to medium-sized operations with annual coal productions ranging from a few thousand tons to 300 kt (330,000 st). These small coal operations are typically in remote areas, inadequately engineered, poorly ventilated and still using rudimentary drilling and blasting mining methods employing antiquated mining equipment and, presenting safety concerns, i.e., methane and dust explosions.

Jan 1, 2011

By R. J. Hamilton

Considerable success has been achieved in recent years in reducing concentrations of respirable dust in UK coalmines; thankfully this has been reflected in significant improvements in pneumoconiosis statistics. However, continuous increases in mechanisation and in rates of working, accompanied by more stringent dust regulations, necessitate the introduction of improved and often more sophisticated methods of dust control. The increased application of exhaust ventilation and air cleaning techniques seems likely to be the most important step forward in dust control in coalmining during the next few years. A typical drivage in a UK mine is not more than 16 ft (5 m) wide and is supported by steel arches. In the past the majority of such roadways were driven by the conventional means of blasting and loading. Since the main purpose of ventilation was to clear blasting fumes and to provide adequate scouring of firedamp, not surprisingly it was usual to have 'forcing' ventilation. Present systems of operation are making increasing use of heading machines and it is not surprising that well over half of all drivages are now ventilated by exhausting methods. (1) The great majority of coal getting in the UK is from longwall faces, usually in seams of less than 6 ft (1.8 m) thickness. Although this method of min¬ing has many advantages in terms of safety and productivity, dust control is made more difficult because of the need for men and machines to work in the same ventilation stream. Much emphasis has been placed on improving the design and methods of opera¬tion of longwall machines to reduce dust production, and improved ventilation has provided greater dilution, and in consequence, reductions in dust concentration. On all machines water is now fed through internal galleries to the cutting elements. Unfortunately, one of the difficulties associated with mining thin seams is that there is some unavoidable cutting in the roof or floor and in many seams there are faults to be traversed and dirt bands which must be removed with the coal. Under these conditions it appears that the use of exhaust ventilation and air cleaning offers the most promising way of achieving satisfactory dust conditions.

Jan 1, 1980

By Walenty Frydel

The paper deals with highly efficient dust collecting systems of the 10-600 type which constitute new generation installations de- signed to eliminate dust hazard in headings driven with roadheaders. A vortex ventube controlling the air flow in the com- bined ventilation system by means of air vortex generated by the ventube drive unit is also presented. From the results of measurements of under-roof concentrations of methane it appears that the application of the vortex ventube makes it possible to decrease the under-roof accumulation of methane more than 10 times.

Jan 1, 1997

By R. Bhaskar

The results of an experimental and theoretical research study into the spatial and temporal behavior of dust in mine airways is summarized in the paper. Experiments were performed in mine airways under both controlled and normal operating conditions. The controlled experiments included the documentation of the concentration and deposition patterns for two types of dust under three different velocities. Real-time dust concentration data were obtained using Real-time Aerosol Monitors (RAM-I) to determine the dispersion coefficient in a mine airway. On the theoretical front, a convection-diffusion model of the dust flow phenomenon in mine airways was developed considering dominant mechanisms affecting dust transport and deposition in mine airways. Mechanisms modeled include turbulent and gravitational deposition, coagulation, and dispersion.

Jan 1, 1988