Search Documents

By Pierre Longtin

"Replacing the aging roadway access to the iconic Golden Gate Bridge, thereby ensuring traffic safety and robustness in case of seismic occurrences, provided an opportunity for major design improvements as well as the development of a parkway that would include the construction of four new tunnels. With an eye to the future, the Doyle Drive replacement project aimed to meet the highest standards for environmental stewardship beyond regulatory requirements. Understanding that lighting equipment is the tunnel‘s subsystem that uses the most energy, the operator was looking for a sustainable solution to light the tunnels. An Intelligent Lighting Control System (ILCS), designed specifically for road tunnels, was acquired to individually control the almost 2000 luminaires lighting the four tunnels. This paper will show the results in terms of energy and operational savings generated over the nine months of operation between the commissioning and the conference in April 2016. INTRODUCTION Electrical & mechanical (E&M) equipment represents an average of 10 % of a tunnel total construction cost. Once the civil infrastructure completed, E&M equipment drives the main part of the expense during a tunnel useful life. Table 1 below describes the impact of various types of energy consumption and their cost impact in tunnels of less than 500 m. It is clear that lighting is the sub-system that requires the most energy. A good lighting strategy is the key to reducing energy consumption due to lighting and a viable solution that will bring important savings in tunnel operations.With a price of $0.14/kWh in California and a planned increase between 3% and 6% per year during the period 2013-2040, the tunnel operators could not afford to overlit the tunnels—particularly when they have to operate it for the next 30 years. However, they also need to maintain the right lighting level to ensure driver safety all the time. The Presidio Parkway project includes the Battery tunnels, which are 240 m (790 feet) and 230 m (750 feet) in length, and the Main Post tunnels, which are 280 m (920 feet) and 315 m (1030 feet) in length."

Jan 1, 2016

By D. Baker

Alternative material handling methods are allowing material handling operations to be performed with increased cost savings. This allows for higher production levels with better returns. RAHCO International Inc.'s Continuous Mining Excavator (CME) has recently received a lot of attention due in part to its operating efficiency, flexibility, and associated low operating costs. The CME is designed to perform three primary functions. These include material excavation, sizing and loading operations. In many applications, a drilling and blasting process can be eliminated. The CME was developed originally in 1985 for open pit coal mining. See figure I. Since this time, it has been proven an effective system for excavating many other types of materials including friable and sticky materials. It has also been shown to suitably handle hard rock in certain site conditions.

Jan 1, 1998

By L. D. Ellison

The ventilation of a bituminous coal mine by means t of a Forced and, or, Exhaust system of ventilation is certainly not new to the mining industry, however, we know from experience that the ventilation of every coal mine presents a variety of problems which are in some instances approached by different methods or means, As in every such problem, there is some difference of opinion as to the advantages and disadvantages of s Exhaust versus Forced ventilation, particularly with regard to safe and effective ventilation of an active pillar area in a gaseous coal mine. We at Island Creek, certainly concede that it is possible to safely ventilate a coal mine by means of Forced ventilation, However, following many years experience in operating a coal mine in an extremely gaseous coal seam, we prefer using an Exhaust system, that is, to reduce the inside mine pressure to a minus atmospheric pressure by means of a mechanically operated fan. This method assures that the return air moving through established airways toward the fan will continue to move in that same direction for a limited time should the fan stop for any reason, also assuring that in the event of a large area fall, the air from the abandoned workings will move directly to the suction side or to the return airways.

Jan 1, 1960

By S. A. Richards

Business planning in the coal' industry revolves around the production and quality forecast. It is difficult to accurately estimate costs and revenues until the production forecast is made. At mines where production comes from multiple sections, quality is tied to each section's production. Blending becomes a part of the planning process. In order to respond to rapidly changing business climate, a reliable program is needed to accurately forecast the effects of changes in key parameters affecting the production. This paper discusses an efficient, intuitive, and economical approach to underground coal mine planning program which uses a PC-based relational database as the programming platform to forecast production and quality. The program was developed at a major coal company. The relational nature of the production planning data, the programming algorithm, and the underlying principles are discussed in this paper.

Jan 1, 1994

By Normand Tassé

Reactive barriers, which consume oxygen, are prospective though unconventional alternatives to physical barriers for Acid Mine Drainage prevention. However, a reactive barrier implies a problem of duration. Pore gases were analysed in several wood waste piles in order to understand the factors which control wood degradation and help to determine the effective life span of such a cover. Long term efficiency seems to strongly depend on the degree of water saturation at the bottom of the pile, likely because the development of a microbial biomass in such an environment helps to keep the amounts of nutriments and readily metabolizable organic substrates at a high level, which in turn promotes oxygen consumption.

Jan 1, 2000

By Zhiyuan Ma, Yong Liu, Xianjin Lyu, Jianfang Lyu, Jikui Zhou

A stable and continuous leaching process for niobium and tantalum extraction from ferrocolumbium tantalum (FT) was developed. The effects of initial concentration of HF and H2SO4, grinding fineness, leaching time, and temperature on the leaching rate of Ta, Nb, Fe, and Si were studied. Experimental results show that the leaching rates of Ta, Nb, Fe, and Si were enhanced by the increase of acid concentrate, fineness, leaching time, and leaching temperature. The optimum process conditions are HF initial concentration of 5 mol/L, H2SO4 initial concentration of 2.5 mol/L, − 74 μm percentage of 65%, leaching time of 20 min, and leaching temperature of 25 °C. Continuous leaching of FT was carried out by feeding ore and acid every 20 min. By leaching with HF − H2SO4 for 4 h, then adding appropriate amount of HNO3 into the solution and keeping for another 1 h, a high Nb extraction rate of 99.8% was achieved. The established method provides a promising technique for the high-efficiency separation of niobium and tantalum from FT.

Jun 5, 2022

By Yi Yang, CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU

Steel slag is an industrial byproduct of steelmaking that is mainly composed of calcium, iron, silicon and magnesium. In addition, depending on the different raw materials entering the furnace, steel slag contains a certain amount of vanadium that is the main source of vanadium production, accounting for 69 percent of the species of the total vanadium raw material [1]. From experience, the production of one ton of steel will generate 1.0 to 1.5 tons of steel slag [2]. However, the utilization efficiency of steel slag is less than 30 percent, and a large amount of steel slag is identified as waste and stacked in tailings. The random stacking of steel slag not only wastes large amounts of limited steel and land resources but also exerts pressure on the environment [3], making it imperative to research the effective utilization of steel slag and recycling of metal resources.

By Yi Yang, CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU

This study presents a method for recovering valuable metals and synthesizing anhydrite from steel slag using sulfuric acid leaching and solvent extraction. The process achieved high leaching efficiencies for V, Ti, Fe, and Mg, and produced anhydrite with 93.09% purity. The leachate was further processed to separate and recover V, Ti, Fe, and Mg using selective stripping and precipitation methods, offering a sustainable approach to steel slag utilization.

Jan 22, 2022

By Xun Zhang, Hang Qiu, Andrea R. Gerson4, Shaomin Lei, Yubiao Li, Yu Meng, Zhenyu Pei, Min Lin

Efficient separation of trace muscovite from the surface/interface of quartz grains was accomplished during oxidizing calcination and catalytic pressure leaching of the hydrothermal quartz. Experimental results suggest that 98.97% or more of the muscovite was separated when quartz sand was calcined at 900 °C for 5 h and then leached by hydrochloric acid and ammonium chloride solutions as substitutes for leaching agents containing fluorides. The chemical processing techniques show high selectivity in purifying quartz sand by transforming mineral muscovite into active structures during oxidizing calcination, and then dissolving the active substances during catalytic pressure leaching

By W. Ghyoot, J. Boonstra, H. Dijkman, C. Buisman, M. Picavet

Paques and Umicore have demonstrated the feasibility of biological treatment of the highly complex Hoboken wastewaters in a1 m3/h pilot plant at Umicore Precious Metals, Hoboken, Belgium. In the first step arsenic was precipitated from copper smelter effluent as As2S3using biogenic produced H2S. Other metals such as copper, lead and cadmium were also removed as MeS to concentrations well below the discharge levels. Subsequently, sulfate and nitrate were removed to low concentrations (<300 mg/l and < 5 mg/l respectively) in high rate engineered bioreactors. Sulfide produced in the sulfate reduction process was recycled to step 1 for metals precipitation. Selenite/selenate was partly removed in the sulfide precipitation step, whereas the excess was biologically reduced and removed as selenium to concentrations <0.2 mg/l.

Jan 1, 2003

By L. W. Saperstein, MJ. Carlson

With the goal of improving the strength characteristics of pneumatically emplaced material used for localized subsidence control, the binding additives fly ash, bentonite, and portland cement were examined for their effect on the support capabilities of coal refuse. It was found that, within certain concentration ranges, all three offered some increase in the ultimate strength of the backfilling mixture. However, portland cement gave the greatest percentage increases. Selection of the appropriate backfilling mixture will allow for the most economical and efficient subsidence control when pneumatic stowing is employed.

Jan 1, 1990

By M. J. Carlson

With the goal of improving the strength characteristics of pneumatically emplaced material used for localized subsidence control, the binding additives: fly ash, bentonite, and Portland Cement, were examined for their effect on the support capabilities of coal refuse. It was found that, within certain concentration ranges, all three of them offered some increase in the ultimate strength of the backfilling mixture; however, Portland Cement gave the greatest percentage increases. Selection of the appropriate backfilling mixture will allow for the most economical and efficient subsidence control when pneumatic stowing is employed.

Jan 1, 1987

By Ernest A. Draeger, James W. Collins

Water only cyclones, sometimes referred to as hydrocyclones, are one of the newest types of coal processing equipment. These devices have achieved wide acceptance as fine coal cleaners in the past decade. Many metallurgical coal plants employ water only cyclones to process 0.5 mm x 0 size coal. Some of these plants have as many as 40 to 50 305-mm-diam units with each unit receiving as much as 9 t/h of raw feed. The growth in the utilization of hydrocyclones is due partly to the energy shortage, partly to the general increase in over-all coal preparation, and also because of a need for a simplified fine coal (0.5 mm x 0 size) gravimetric separator. Large diameter water only cyclones are also available and in use to process feed sizes up to 32 mm in size. However, the size normally employed for cleaning 0.5 mm x 0 coal are 356 mm or 305-mm-diam for single-stage circuits. In two-stage circuits, the secondary units are normally the same diameter as the primary units or smaller, such as 203-mm-diam. By using the small diameter cyclones and treating a closely sized feed, 0.5 mm x 0 only, it has been found that the probable error or imperfection of the water only cyclones is comparable to that obtained on the same size fraction treated in a large 610-mm-diam heavy media cyclone washing 38 mm x 0. The water only cyclone can approach the efficiency of a heavy media cyclone when cleaning fine solids because it creates its own dense media by accumulating high specific gravity particles in the wide angle conical section of the cyclone. A cut-away cross sectional view of a water only cyclone is shown in Fig. 1. It is also true that when treating a wide range of sizes (38 mm x 0) in heavy media cyclones, the smaller size particles (0.5 mm x 0) separate in proportion to the split of the media through the cyclone rather than by particle density.

Jan 8, 1980

By LeRoy D. Loy

Would you believe me if I told you the constant battle between Government regulatory agencies and industry could be won by both sides? No, I&apos;m not crazy, nor have I been soaking up any of that fine Kentucky whitelightning. But I have recently been a participant in a battle where both sides won. Actually, I&apos;m using the term "battle" loosely because, in reality, it wasn&apos;t a battle at all - despite the fact that all the ingredients were there for a monumental struggle; i.e.. government, industry, special interest groups and a controversial issue - the development of effluent limitations. I&apos;d like to tell you about it. Historically, on one side of the battle, government has always been ac¬cused of adopting regulations with limited evaluation of existing technologies; and then with seemingly no regard for the economic consequences. On the other side, industry gets punished by government&apos;s harsh actions because of their past "do-nothing" attitude toward pollution control. Recently, this battle seems to be losing steam, because both government and industry are beginning to realize that, ultimately, they both will lose. Even more important is the fact that both sides are, or should be, working for industrial expansion compatible with environmental protection.

Jan 1, 1977

By G. Aggistalis, N. Kazilis, C. Rawlings, N. Rachaniotis, S. Raptopoulos, M. Knights, R. Game

The Egnatia Odos (Odos meaning road) is one of Greece’s largest ever highway construction projects and one of Europe’s most important. The Highway will assist in the connection of the Greek Ionian/Adriatic Coast with Turkey and the Black Sea reviving an historic Roman alignment “Via Egnatia” connecting Rome to Constantinople (now Istanbul). There are 74 twin tunnels (60 bored and 14 cut-and-cover) with lengths ranging from 160 m (175 yd) to 4,600 m (5,031 yd) and 100 m (109 yd) to 270 m (295 yd),respectively. The complex geology and resulting physical geography have had a major influence on both the design and construction of these tunnels. This paper describes the management, design and construction challenges of these numerous tunnels.

Jan 1, 2005

By Ahmed M. Nofal

This article reviews some important characteristics of the known Egyptian phosphate deposits, such as mining conditions, transport criteria, quality of products affecting their export markets and utilisation in fertilizers industry. Special attention will be given to the newly discovered large deposit of Abu-Tartur with some billion tons of ore reserves. A big project is now under implementation on Abu-Tartur deposit where the long-wall method of underground mining will be applied and a flow sheet of beneficiation will be in operation including a particular feature nontraditional in phosphate processing: high-intensity magnetic separation to eliminate dolomite impurities. Comparison with some international phosphates will be tried in order to trace the situation of Egyptian phosphates in the world market.

Jan 1, 1993

By C. Cassios

EIA is a procedure aiming the elimination of adverse impacts to the environment from undertaken projects. Historically, it starts in 1969 when NEPA (Nat.Env.Prot.Agency) in the US initiated the EIA ? EIStatement. The EIA procedure was adapted by the European Union with the directive 337/85 and in Greece the Common Ministerial Decision 69269/90 enforced it to the Greek legislation. However, mining enterprises in Greece long before the implementation of the European Directive and in accordance to the legislation of the Public Law 998/79 for the protection of the forested lands were obliged to submit EIA?s and get an approval in order to operate in forested areas. The submitted and approved EIA?s and their implementation by the mining companies were among the positive aspects of the EIA procedures. This paper is examining the impacts of EIA?s in the Greek mining industry its positive aspects as well as their difficulties and their role for the reclamation procedure. The technical and procedural aspects which EIA presents for the mining industry are commented, while proposals, for a more flexible EIA implementation for the Greek Environment are also presented.

Jan 1, 2002

By John L. Stauffer, Allan Lipton, Kim Leitzel, Lesley Gaydos, Laurence M. Demers, Douglas C. Kuhn

Eicosanoids and cytokines produced by the alveolar macrophage (AM) are key mediators of pulmonary inflammation and fibrosis resulting from occupational exposure to mineral dust. In order to determine if eicosanoid and cytokine production are altered by chronic inhalation of coal dust, we compared the production of prostaglandin E2 (PGE2), thromboxane A2 (TxA2), leukotriene B4 (LTB4), interleukin 1 (IL-1), tumor necrosis factor (TNF) and platelet-derived growth factor (PDGF) by cultured AM from non-smoking normal human volunteers and coal miners. Inhibitors of eicosanoid biosynthesis were administered to AM from coal miners in order to determine if a link between eicosanoid and cytokine production exists in these cells. Basal PGE2, TxA2, TNF and IL-1 production by AM from active miners was increased compared to AM from normal volunteers. However, the production of these eicosanoids and cytokines by AM from former coal miners was reduced compared to control AM. Administration of the cyclooxygenase inhibitor, suprofen, and the lipoxygenase inhibitor, nordihydroguaiaretic acid, reduced PGE2 and TxA2 production in miners&apos; AM but had no effect on LTB4, IL-1 or PDGF production. Specific inhibition of thromboxane synthase by UK38,485 was associated with a significant reduction in TNF production in active miners&apos; AM but had no effect on PGE2, LTB4 or IL-1 production. The prostacyclin analogue ZK96,480 also specifically inhibited TxA2 production in active miners&apos; AM. The results of these studies suggest that coal dust exposure is associated with alterations in AM eicosanoid and cytokine production which may be relevant to the development of pulmonary inflammation and fibrosis. In addition, the lack of effect of inhibitors of PGE2 biosynthesis on IL1 production in miners&apos; AM suggests the production of these intercellular messengers may not be linked in AM chronically exposed to coal dust.

Jan 1, 1991

By Laurence M. Demers, Douglas C. Kuhn

It has been suggested that radicals on the surface of dust particles are key chemical factors in the pathophysiology which results from the occupational inhalation of coal and silica dust. In addition, oxygenated derivatives of arachidonic acid (eicosanoids) have been implicated as important biochemical mediators of mineral dust-induced lung disease through their role in bronchial and vascular smooth muscle reactivity, inflammation, and fibrosis. Therefore, we assessed eicosanoid production by the rat alveolar macrophage (AM) exposed in vitro to mineral dusts with varying surface chemical characteristics in order to determine if radicals associated with the mineral dub1 could influence the production of pro-inflammatory mediators in the lung environment. Rat AM were exposed to freshly fractured or "stale" bituminous coal dust, as well as untreated silica or silica calcined to 500°C and 1100°C. Prostaglandin E2 (PGE2) and thromboxane B2 (TxB2) levels in incubation medium were determined by specific radioimmunoassay. When AM were exposed to freshly fractured coal dust, PGE2 and TxB2 production were markedly increased. In contrast, exposure of AM to "stale" dust significantly reduced PGE2 and TxB2 production. In vitro exposure of AM to untreated silica resulted in a significant increase in PGE2 and TxB2 production compared to control. However, exposure of AM to silica calcined to 1100°C resulted in eicosanoid levels which were not significantly different from control. These findings suggest that radicals associated with respirable coal and silica particles may play a key role in the ability of mineral dust to activate AM eicosanoid production.

Jan 1, 1991

By John H. N. Yen, James M. Marquardt, Larry H. Heflin

INTRODUCTION On February 17, 1995, WMATA Contractor J.F. Shea holed through the last segment of rock tunnels of the planned 103-Mile Rapid Transit System for the Washington Metropolitan Area Transit Authority. Through the joined efforts and cooperation between the owner and the contractor, the project was completed on time and within budget. The Glenmont extension is on schedule to open in Mid-1998. The complete 103-mile system is scheduled to open in 2001. WMATA’s earlier 19 miles of rock tunnels had been done since 1976 ? By drill and blast with heavy horseshoe steel sets, sets with shotcreting over wire-fabric by TBM and NATM. All rock tunnels were primarily in metamorphic gneiss and schist, part of an east coast lithology that outcrops in a band running from below Richmond, Va. To above New York City. The 5,400 ft. long twin six meter tunnels of the Glenmont line had been earlier de-signed in 1979 by URS of NYC using Jenny Engineering of Pittsburgh, Pa., as a tunnel design specialist sub consultant. Jenny had provided two alternative designs, one conventional drill and blast horseshoe and one for Tunnel Boring Machine. Funding considerations had put the design on the shelf and it was clear that the state of the art had led to improved design methods in the intervening years. Before URS was tasked to update their design in1992, the Authority reviewed its earlier hard-rock experiences in light of the funding mandate to complete each segment on a limited budget and an expedited schedule. Many factors considered and many opinions were in leading to a final decision to drop the earlier designs and redesign for a single designated means of tunneling. That method was the New Austrian Tunneling Method. The NATM had been used earlier on WMATA for both soft-ground and rock tunnels. In the public’s eyes the NATM had become inextricably linked with the use of PVC’s and filter material enveloping or partially enveloping the underground structures to give the holy grail of tunnels, a water-tight structure. Although this link of waterproofing methods with excavation and support methods was essentially severed, a general feeling of their interdependence no doubt helped lead to acceptance of the NATM decision because of the waterproofing design that accompanied it. The Authority decided to drop the TBM and conventional options and provide bid documents for NATM only. URS asked LAW Engineering of Atlanta to provide the NATM design of the tunnels and associated shafts.

Jan 1, 1997