Search Documents

By P K. Kaiser, D A. Malovichko

Highly stressed excavations in hard brittle rock may fail by self-initiated, triggered or dynamically loaded strainbursts (Moss and Kaiser 2021). The low-frequency part of seismic radiation associated with strainbursts is described by a crush-type seismic source mechanism with a significant negative (implosive) isotropic component and a ‘pancake-shape’ CLVD deviatoric component. The seismic source is co-located with the excavation damage site. For such strainbursts, the ejection velocity is primarily related to the depth of strainbursting, the rock mass bulking characteristics, the duration of the bulking process, and the effectiveness of the support system. For dynamically loaded strainbursts, the displacement and energy demand may be augmented by the impact of the stress wave from a distant seismic event. This article describes the failure process and factors contributing to rock deformation and energy demands for support design. Case examples are used to demonstrate the dependence of rock displacements, rock ejection and energy demand on the factors described above. A seismic source model is proposed to assess the depth of strainbursting and the duration of the related bulking process by using seismic monitoring data. The implications for support design are briefly discussed.

Apr 26, 2022

By Earl Cook

A high-energy economy based on fossil fuels is in fundamental conflict with an ideal of clean air, clean water, undisturbed scenery, and maintenance of fragile ecosystems. There is an inevitable trade-off between the material standard of living of a modern society and the conservation of its environment. During the past four years, some of the costs of environmental protection have been internalized in the energy-flow system of the United States. The cost of bituminous coal and fuel oil usable under new air-quality standards has doubled or more. The cost of mining coal underground has risen because of a 20-30 percent reduction in productivity resulting from new environmental health and safety legislation; the economic impact of proposed surface-mine regulation may be equally severe. The cost of producing electric power has been rising at a 12 percent annual rate because of environmental costs, and would be climbing still more steeply were it not for the continued forced subsidy of natural-gas consumers by natural-gas producers. The efficiency of the automobile, already a monument to the triumph of self- indulgence over economy, is being further decreased by addition of anti-pollution devices. Part of the recent sharp rise in agricultural costs stems from the fact that five energy units of fossil fuel go into U.S. agriculture for every energy unit of raw food that leaves the farm; further large injections of fossil-fuel energy occur in the transport, processing, and refrigeration of farm products.

Jan 1, 1974

By K. Kavouridis

The energy and climate protection policy of European Union (EU), and its Member States adopted in 2007 bridges security of supply, environmental protection and competitiveness. The objectives of the EU energy and environmental strategy cover the foreseeable period till 2020. It assumes all sources of energy will be needed. The objectives for renewable and improved efficiency are ambitious; it must be established if they are also realistic. Coal can continue to make valuable contribution to the security of supply and low price of electricity, only with technologies allowing for drastic reduction of the CO2 emitted of its combustion. The aimed at -20% reduction of green-house gases (GHG) of EU-27 by 2020 is an objective limited in time and content. Europe produces less than 15% of global CO2 and this will be reduced to 10% in 2030. Emissions Trading (ET) is to remain the central instrument for CO2 management, especially in the power sector. ET scheme (ETS) or other mechanisms need designing to create an incentive for investment in higher efficiency and technologies and to Carbon Capture & Storage (CCS). The ETS as the climate protection instrument of the EU can become a heavy burden (high fuel and electricity prices, less security of supply) or it can create a climate for modernization of fossil fuel power plants. The suggestion in this paper of fuel-specific benchmark system for CO2 allocation after 2012 can combine the emission levels to be reached with a strong drive to invest, the necessary investment security, transparency and the principle of proportionality. A Benchmark System as recommended by coal industry could adapt to the different circumstances in the long term and comply with EU energy and environmental policy objectives.

Jan 1, 2008

By W. G. Prast

Investments in fuel minerals and non-fuel minerals by petroleum companies are not a new phenomena. During the past 25 years, oil firms have entered mining via the acquisition route as well as by the direct development of grassroots mines. In the early 1980s, the "merger mania" in the natural resource industries came to a head. Oil company takeovers of mining firms, as well as other mergers between oil producers, captured headlines repeatedly, and speculation ran wild as to who would next acquire whom. Table 1 summarizes leading mining company mergers in the past two decades. There are some special features to the latest round of minerals investments undertaken by oil companies. First, direct takeovers of mining companies have become the preferred means of entry into minerals, with entry from scratch being relegated to the sidelines. This was not always the case. While there are instances of oil firms buying coal and copper companies dating back to the 1950s and 1960s, most of the early minerals work by petroleum firms was from internally generated projects. When the oil companies first became involved in uranium, for example, the uranium mining industry was in its infancy. There was not much market structure to buy, and it was relatively easy for everyone to get into uranium on the ground floor.

Jan 1, 1983

By Michael Markels

The United States Environmental Protection Agency (EPA) is charged under the Federal Water Pollution Control Act Amendments of 1972 with establishing effluent limitations which must be achieved by point sources of discharge into the navigable water of the United States. Section 301 (b) of the Act requires the achievement by not later than July 1, 1977, of effluent limitations for point sources, other than publicly owned treatment works, which are based on the application of the best practicable control technology currently available as defined by the Administrator pursuant to Section 304(b) of the Act. Section 301(b) also requires the achievement by not later than July 1, 1983, of effluent limitations for point sources, other than publicly owned treatment works which are based on the application of the best available technology economically achievable which will result in reasonable further progress toward the national goal of eliminating the discharge of all pollutants, as determined in accordance with regulations issued by the Administrator pursuant to Section 304(b) to the Act. Section 306 of the Act requires the achievement by new sources of a Federal standard of performance providing for the control of the discharge of pollutants which reflects the greatest degree of effluent reduction which the Administrator determines to be achievable through the application of the best available demonstrated control technology, processes, operating methods, or other alternatives, including, where practicable, a standard permitting no discharge of pollutants.

Jan 1, 1975

By I. Longson

Maintaining control over underground environmental conditions in the United Kingdom is increasingly dependent on the contribution of underground booster fans. Given the recent trends of higher rates of production from a fewer number of coal faces with higher levels of mechanization and higher power consumption, the effect has been to place a greater load on the mine ventilation system. This has increased the scale of potential problems that may arise should any of the main ventilation control devices not perform at the required full duty. This is particularly true for underground booster fans. Major changes occur in the main ventilation parameters on the stoppage or restart of a booster fan which results in a temporary loss of environmental control. This paper analyzes the impact of such events and details a mathematical model thar has been developed for a single-mesh circuit containing a main and a booster fan. Predictions based on this simple model are presented and discussed with particular reference to the energy changes occurring within the ventilation system immediately following a booster fan stop or restart

Jan 1, 1995

By E. Poeck, R. Garvey, U. Ozbay, K. Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the mine-scale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures which most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps. INTRODUCTION The analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but for deep cover and squat pillar geometries, less accuracy has been achieved in predicting pillar performance (Mark 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs. This paper presents a study of pillar stability through the back analysis of the Crandall Canyon Mine collapse, which occurred in August of 2007. Pillar-scale models are utilized for the calibration of material properties and assessment of potential instability under varying conditions, and mine-scale models are constructed in an attempt to reproduce widespread failure and correlate with observations at the mine. Special consideration is given to the properties of the coal and the coal/rock interface, and kinetic energy is calculated throughout the course of the simulations to gauge the level of instability when pillar failure occurs. Models were constructed using the Universal Distinct Element Code (UDEC) (Itasca, 2014)."

Jan 1, 2016

By Thomas P. Bligh

Underground and earth covered construction offers a real and significant opportunity for saving energy, reducing building costs, and preserving valuable land resources. These methods lend themselves to mass production techniques without the adverse effects of endless visible repetition and can effect an energy savings of 75% or more.

Jan 1, 1976

By Hoke M. Garrett

The domestic cement industry demands about 550 trillion Btu annually, at a time when reduced fuel use has become a necessity due to the energy shortage. In terms of the overall power picture, that 550 trillion Btu, which includes both fossil and electrical energy, means about 0. 870 of all energy consumed in the U. S. The various factors influencing reduction of this energy consumption are the subject of this paper. Nationally, the energy shortage is being tackled on two fronts--increasing supply and reducing demand. Making cement consumes energy; therefore, the industry cannot join the effort to increase the energy supply except indirectly as noted later. Demand can also be attacked on two fronts--by reducing cement consumption or by reducing the amount of energy required to make cement. The following discussions on reducing cement industry energy consumption center briefly on the prospect of reducing cement consumption followed by a broad evaluation of the potentials for improving cement-making thermal efficiency.

Jan 1, 1974

By T. Cienski

The paper presents and discusses the results of a detailed study conducted on the subject of energy consumption in the comminution of industrial minerals. The study was based on pilot circuit testing, plant operating data collection, detailed equipment data and literature research. The areas covered by investigations include: high efficiency classification; air classifiers for cement grinding circuits; grinding aids in dry grinding: dry grinding circuit, control based on particle size measurement. Results obtained indicate a large potential for the reduction of energy consumption, in particular in the traditionally high cement clinker grinding circuits. Better classification techniques and correct application of grinding additives can significantly reduce power used per ton of product and also substantially increase grinding circuit output.

Jan 1, 1990

By O. V. Bush

Most governments recognize that energy efficiency represents a partial solution to reducing global capital shortages and environmental crises that threaten to seriously impede economic growth. Much of the United States and many foreign countries are embracing the concept of Integrated Resource Planning (IRP) which incorporates Supply Side Management (SSM) and Demand Side Management (DSM). Since SSM comes at twice to three times the cost of DSM, it makes economic sense to employ the energy conservation techniques of DSM. This paper will explain these concepts and some of the incentives being put forward by governments and utilities to promote DSM.

Jan 1, 1995

By Noel Jarrett

Energy consumption and distribution in aluminum production, conservation accomplishments, and future goals are presented. Electrolysis and electrode manufacture show the greatest promise for major improvements. Means are proposed for reducing waste heat generation in smelting and for conserving energy in anode manufacture by furnace design and substitution of other materials for petroleum coke. Hall-Heroult Process modifications, alternative designs, and the Alcoa Smelting Process are discussed as energy savers. Scrap recycling, more use of aluminum in transportation, and the installation of offshore smelters in less developed countries are shown to be additional means of coping with possible energy dislocations.

Jan 1, 1981

By George K. McCord

It is a pleasure to participate in this Fall meeting of the Society of Mining Engineers to discuss energy conservation trends in the cement industry. Energy is the "life blood" of American industry, and the ability to use available energy resources efficiently may well determine the future of our nation and of its industries. The Federal Energy Administration has classified cement manufacture as one of several energy-intensive industries in the U.S. and has selected the Portland Cement Association to make a detailed study of possible energy conservation measures. Member companies of the Portland Cement Association represent about 85% of the cement producing capacity of the United States and 100% of Canadian capacity. Stated briefly, the purpose of the Association is to extend the uses of portland cement and concrete through research and development, market promotion, education, and public affairs work. PCA's general offices and research laboratories are located in Skokie, Illinois. Our staff of engineers, scientists, and research personnel make the PCA uniquely qualified to perform an energy conservation study of the kind requested by FEA.

Jan 1, 1975

By James A. Commins

Accurate engineering predictions of energy needs for pollution control equipment used in surface mining operations is critically important to sound management selection of control alternatives. This paper will describe a procedure for evaluating two control alternatives with different energy needs. Three steps are involved: an analysis of the pertinent regulations, a determination of the size distribution of the particles being emitted, a calculation of the energy needs and costs of the candidate control systems as a function of these regulations and emission characteristics. The principal air pollutant to be controlled in surface mining operations is particulates, or dust, some of which is already on the material introduced into the primary crusher and other dust which is generated by the various steps in the subsequent processes. The requirement for control stems both from regulations concerning workers at the operating site, and the community surrounding the operations. In order to speak quantitatively about the need for control we will use regulations that pertain in Pennsylvania although it must be borne in mind that such regulations vary according to juristiction.

Jan 1, 1975

By P. T. Kane, O&apos

Capital and energy are the dominant cost factors in nickel production from laterites. Since the 1973 energy crisis, pyrometallurgical developments have been oriented towards lower cost sources of energy and higher grade ores and hydrometallurgy towards higher recoveries and greater flexibility in types of ores treated. Energy recuperation offers some potential, but at a price. 'The lower energy acid leaching process is indicated to have the greatest potential, particularly with its inherently high cobalt recovery.

Jan 1, 1979

By E. Forssberg, Y. Zeng

Fine crushing and rod grinding have been investigated using a laboratory-scale jaw crusher and a rod mill. The net energy consumption in both crushing and grinding was evaluated from torque measurements. An empirical relationship was established between energy consumption, particle size and operating parameters. When the mill feed size is reduced, through fine crushing, to about 80% passing 3 mm, the energy consumption will be minimized in a comminution chain of fine crushing and coarse rod grinding. The results in fine crushing were compared with a large-scale test.

Jan 1, 1993

By Dan Nilsson

Open pit mining is the strong sector of the American mining industry. In the middle of the 60's. 17-18% of the ore in metal mines was mined with underground methods. From the middle of the 60's to 1980 the production in open pit metallic mines increased from about 400 to close to 600 million short tons while at the same time the underground mine production decreased a little, from about 90 to about 80 million tons. Less than 15% of the ore prodction now come from underground mines. Large amounts of waste rock were also handled in the open pits. In the middle of the 60's about 600 milion tons were handled, in 1980 1,200 million tons were moved. This means that the average stripping ratio increased from about 1.5 to over 2.0 tons of waste rock per ton of ore, figure 1.

Jan 1, 1983

By Wenkai Wan, Charlie C. Li

Strain burst can occur in underground hard rock excavation when the in-situ stresses are high enough. The prerequisite for rock burst is that the total energy released from the rock mass is higher than the energy needed for rock fracture. The total released energy is contributed by both the burst rock and the surrounding rock. The part of the energy from the burst rock is constant per unit volume of the rock, but the part from the surrounding rock is associated with the burst volume. A greater amount of energy will be released from the surrounding rock in the case of a larger volume of burst rock. The postulation for the energy conversion in strain burst is verified through a FLAC3D model in the paper. It is assumed that the strain burst occurs in a circular tunnel that is located in the hydrostatically loaded rock mass in the model. Six pairs of notches with different depths are created in the opposite walls of the tunnel to simulate the bursts. The energies released from the notch rocks and from the surrounding rock are calculated during the burst. The simulation results show that the percentage of the energy released from the surrounding rock in the total released energy increases with the notch depth. The numerical modelling confirms the postulation that the surrounding rock contributes more energy than the burst rock itself in large-scale strain bursts

Apr 26, 2022

By R. Leithner

The need/wish to sequestrate CO2is based on the assumption of the International Panel of Climate Change (IPCC), that CO2 maybe the major driver in climatic changes, i.e. especially the anthropogenic CO2emissions due to the combustion of fossil fuels like coal, oil and natural gas will increase the atmospheric CO2-content, which will lead to higher temperatures in the atmosphere. The 0.03% CO2in the atmosphere have a 22% share of the natural greenhouse gas effect of 33 K necessary for life on earth. The main share of 62% has the water vapour in the atmosphere. Only if one concentrates on the greenhouse gas effect of the gases beside water vapour, CO2 becomes most important with 58% influence. In addition there are other influences on the climate like: • Eccentricity of earth’s orbit, precession of orbital plane, obliquity and precession of earth’s rotation axis (Milankovitch’s theory) • Sunspots and magnetic field of the sun • Changing streams in the ocean • Volcanic activities • Distribution of continents on the surface of the earth • Impact of meteorites • Change of insulation by interplanetary dust [Muller, R.A. 2000] etc. To answer the question, if the CO2-content in the atmosphere has an important or exclusive influence on the earth atmospheric mean surface temperature, one should look into history. Figure 1shows the mean temperature of the atmosphere and the atmospheric CO2-content time histories 1 billion years back; no correlation can be found between them. Nevertheless a lot of countries have committed themselves to reduce their CO2-emissions.

Jan 1, 2004

By Jonathan G. Price

The 2011 report titled ?Energy Critical Elements: Securing Materials for Emerging Technologies? by the American Physical Society?s Panel on Public Affairs and the Materials Research Society surveys potential constraints on the availability of these elements and identifies five specific areas of potential action by the United States to ensure their availability: 1) federal agency coordination; 2) information collection, analysis and dissemination; 3) research, development and workforce enhancement; 4) efficient use of materials and 5) market interventions. Energy-critical elements (ECEs) are a class of chemical elements that currently are critical to one or more new energy-related technologies. A shortage of these elements would significantly inhibit large-scale deployment, which could otherwise be capable of transforming the way in which energy is produced, transmitted, stored or conserved. The report addresses elements that have not been widely extracted, traded or used in the past, and therefore are not the focus of well-established and relatively stable markets (such as carbon in coal or uranium as fuels, copper, aluminum, nickel and iron, all of which are clearly vital in energy applications).

Jan 1, 2011