Search Documents

By P. Rusin

A new bacterium, Thiobacillus cuprinus, can extract copper from chalcopyrite as rapidly as T. ferrooxidans. On solution with and without nutrient amendments and bacterial growth media were supplemented with T. ferrooxidans or T. cuprinus in shake flask studies. Both species extracted -42% of the copper using growth media. In one case, T. cuprinus solubilized approximately twice as much copper as T. ferrooxidans utilizing a seeded On solution. Thiobacillus prosperus also oxidizes chalcopyrite and tolerates high chloride concentrations. These sulfide-oxidizing bacteria are representatives of the mixed microbial community found in sulfide dumps. Rates of biological copper extraction from sulfide ores, using the native microbes, have been significantly enhanced by amending On solution with PGM.

Jan 1, 1994

By Noel C. Joughin, Orrie Fenn, Brian E. Protheroe

Work has shown that the use of high-pressure water jets enhances the performance of mechanical cutting in very hard rock. To assess the potential of this approach for use in conjunction with free rolling cutters, a series of tests has been conducted using both disc and button type cutters, to determine the relative effects, on cutter performance, of variations in relevant jet and cutting parameters. In these tests it was found that water jet assistance can result in reductions in the forces on a free rolling cutter typically of the order of 40%.

Jan 1, 1985

By Erik S. Bernard

"INTRODUCTION Reinforced Concrete (RC) members such as beams and columns are usually required to include stirrups to maintain post-crack shear capacity, and some may include stirrups that act as confining steel to maintain structural integrity during a seismic event (eg. NZS3101, ACI 318). To achieve seismic resistance, the spacing between stirrups is usually required to be much closer than is ordinarily prescribed for non-seismically resistant structures. Each stirrup must also fully enclose the longitudinal reinforcement with long end-hooks to ensure that the contained concrete is sufficiently restrained during reverse-cycle loading and the reinforcing bars are confined to prevent buckling. The close spacing between stirrups can lead to congestion of reinforcement within members, and can also be expensive to construct due to the labor-intensive nature of steel fixing. A possible alternative to closely-spaced stirrups is the use of fibers to provide restraint and confinement during a seismic event, although this is not yet recognized in codes. Previous experimental research (Jiuru et al, 1992; Filiatrault et al, 1995; Bayasi and Gebman, 2002; Billington and Yoon, 2004) has demonstrated that steel fibers are relatively effective in this application, but suffer the problem that their stiffness can make them difficult to consolidate within an already tight reinforcement cage, especially if they are relatively long (>40 mm). Moreover, steel fiber reinforced concrete (SFRC) is subject to embrittlement with the passage of time, leading to a steady loss of ductility beyond crack widths of 1-2 mm (Banthia and Trottier, 1994; Bernard and Hanke, 2002; Bernard, 2014; Bjontegaard et al, 2014; Bernard, 2015). Since cracks during seismic events are generally much larger than this, embrittlement may present a challenge to the long-term efficacy of SFRC during seismic events. An alternative to steel fibers for enhancement of seismic resistance is the use of macro-synthetic fibers. This type of fiber usually offers the advantage of being flexible so that consolidation is easier between reinforcing bars. They also offer superior durability compared to steel fibers and can reduce flexural crack widths (Bernard, 2016). Several recent small-scale investigations (Ma et al, 2012; Carnovale, 2012; Osorio et al, 2014) have indicated that macro-synthetic fibers can produce meaningful improvements in seismic resistance if used in combination with conventional steel reinforcing bars. The present investigation has extended research in this field by examining whether embossed macro-synthetic fibers can be used to increase the spacing between stirrups while maintaining seismic resistance."

Jan 1, 2016

By Rahul Singh, Sunil Kumar, Erich Dohm, Maoming Fan

The rapid increase of P2O5 use for food, biofuels, and LiFePO4 batteries etc. accelerates the depletion rate of phosphate reserves. In the phosphate industry, a significant amount of ultrafine phosphate has been discarded as slime tailing due to processing difficulties. The major problems associated with ultrafine particle flotation are low probability of bubble-particle collision and adhesion, and high probability of unwanted gangue particles entrainment. This paper investigates the enhanced ultrafine phosphate particle flotation probability by Eriez’ CavTube generated fine/ ultrafine bubbles and the improved flotation selectivity by wash water etc. Ultrafine phosphates with various gangue minerals of quartz/muscovite, calcite/dolomite, and iron/ silica were studied. Microscopic observations show that the entrained ultrafine gangue minerals can be minimized by using wash water in column flotation. A three-factor threelevel central composite experimental design was conducted for ultrafine phosphate flotation. For comparison, both benchtop mechanical cell and laboratory column flotation tests were performed at their optimal respective flotation conditions. Using Eriez CavTube column flotation technology for Industries Chimiques du Senegal (ICS) ultrafine slime tailings, a concentrate grade of 36.0% P2O5, was achieved at 89.4% P2O5 recovery. Improved flotation performance was achieved using column flotation as compared to benchtop mechanical cell flotation. The benefits of Eriez’ column flotation technology realized from this study include the high P2O5 grade and recovery.

Feb 1, 2024

By R. Hardy

LaModel is a boundary-element program capable of calculating the displacements and stresses in thin bedded deposits such as coal, salt, or potash. Throughout its history, it has continually been upgraded in order to expand analysis detail and stay current with the latest advances in computer technology. The most recent enhancements include: an increased grid size capability, a significant increase in the speed of the automatic grid generation using an AutoCAD visual interface, implementation of subsidence-based horizontal strain calculations for multiple-seam situations, and pillar safety factor calculations. To demonstrate these new features, a multiple-seam case study of a longwall panel undermining an active set of main entries is presented.

Jan 1, 2006

By D. F. Martin

Sustainability is typically understood as having three interrelated dimensions-environmental, economic, and social. However, far less attention has been paid to social sustainability than to the other two forms. The paper argues that one of the difficulties in giving substance to the concept of social sustainability is that it is inherently value-dependent and has major conceptual, definitional and therefore measurement issues. This is particularly the case in complex crosscultural environments such as those found in Australian mine hinterlands with significant Aboriginal populations. Nonetheless, a concept of social sustainability can provide an important counter to the usual focus on environmental and economic sustainability, and can productively guide the minerals industry in its engagement with the Aboriginal people of mine hinterlands. The paper outlines a set of principles for socially sustainable communities, and proposes means by which these principles can be implemented. It further suggests that these principles may have broader applicability than just in the case of Aboriginal people.

Jan 1, 2005

By Somia Gurunathan, Harry Castrantas

Hydrogen peroxide and calcium peroxide are used to improve the extraction of gold/silver and reduce cyanide consumption in heap leaching and mill leaching operations. FMC's standard grade H2O2 and FMC's Permeox™ solid peroxygen, a formulated product containing cao2, was used for the experimental work. It was found that the rates of release and the longevity of these peroxygens in ore-cyanide mixtures are significantly different. When choosing a peroxygen, one of the key factors is extrac­tion time, with the longer extraction times of heap leaching primarily favoring calcium peroxide and the shorter extraction times of mill leaching primarily favoring hydrogen peroxide. A series of laboratory leach tests showed the choice between H2O2 and CaO2 to be ore and process specific. H2O2 and/or Permeox™ improved the gold extraction in four out of five ores tested. (2 sulfide and 2 oxide). Mixtures of H2o2 and Permeox™ were also found to significantly increase the gold extraction rate. A fifth ore (sulfide) did not respond to peroxygen treatment. In addition, savings in NaCN consumption was obtained with Permeox™. Both peroxygens offer economic incentives to gold processing.

Jan 1, 1992

By Morgan M. Sears

The stability of gateroad pillars is crucial in deep-cover longwall mining, especially during transitions to wider panel layouts. This study evaluates the transition from a 700-foot to a 1,000-foot panel layout with an inter-panel barrier in a deep-cover longwall mine in Southwestern Virginia to identify a configuration that enhances stability and reduces operational risks. Using the LaModel program, three pillar configurations were simulated to assess their performance based on stress distributions and pillar safety factors. These included the previously used 4-Entry Yield-Abutment-Yield layout, the current 3-Entry Yield-Abutment layout with a 220-ft inter-panel barrier, and the proposed 3-Entry Yield-Yield layout with a 320-ft inter-panel barrier. The findings of this study suggest that the proposed 3-Entry Yield-Yield pillar layout is more effective in managing stresses in deep-cover mining environments. By optimizing pillar placement and improving load management, this layout could positively impact mineworker safety and health. The study underscores the importance of advanced simulation tools in developing innovative solutions to address the challenges of modern longwall mining operations.

Feb 1, 2025

By C. Patrick

Project scheduling is a deterministic technique utilizing single estimates of activity durations. In reality, activity durations are stochastic and can be better represented by probability distributions. This paper describes the development and utilization of a project scheduling simulation which combines analytical scheduling with stochastic activity durations. The purpose is to provide a method to analyze the sequencing of mining production processes and predict the effect of any planned changes. The simulation is demonstrated through realistic examples, such as longwall face-to-face transfer sequencing and the effect of varying advance rates on longwall development sections. Statistical data, to make more informed production decisions, are generated in the form of project activity/path criticality and project duration distributions.

Jan 1, 1995

By Akram Marseet, Andrew J. Petruska, Rik Banerjee

Underground mine roof bolting is a crucial operation for miners’ safety and mine sustainability. Since roof bolting is a manual or human-supervised operation, miners’ safety is at risk due to dust or rock falls. Traditional machine learning algorithms have shown limitations to detecting drillable areas, mainly due to harsh lighting conditions. The authors propose an adaptive deep-learning framework for autonomous roof bolting. The proposed framework is based on implementing a binary semantic segmentation algorithm on color images to classify pixels that belong to rock from those that belong to non-rock. Significantly, the proposed framework implements deep learning semantic segmentation on images from traditional and neuromorphic vision sensors in underground mines. The performance of the proposed model shows an impressive accuracy level of at least 98% at a low number of training epochs with smooth learning curves. The high accuracy enables the implementation of autonomous roof bolting, greatly improving miners’ safety and operational efficiency while reducing human exposure to safety hazards. This research will advance the use of deep learning in mining automation and has the potential to revolutionize the traditional mining industry.

Feb 1, 2024

By Justyna Swolkień, Nikodem Szlązak, Dariusz Obracaj

Polish coal mines are characterized by severe geological conditions and the co-occurrence of natural hazards. These hazards are associated with methane and dust emissions during mining processes which can provide methane, dust or methane-dust explosions. Besides, there are such natural hazards as gas and rock outbursts, rock bursts, spontaneous combustion of coal and environmental heat load. The mutual influences of various geological conditions, as well as the natural hazards, intensify the increase of the methane explosion hazard. The occurrence of methane explosions in the Polish mining industry between 2013 and 2108 are analyzed. Fatal accidents are compared with similar events in the global mining industry. The methods of preventing the explosion hazard as well as methane emission control in the Polish coal mining sector are presented. Methane hazard prevention should be adapted to levels and other natural hazards, especially those related to ventilation of underground mine. The methods of preventing methane emissions into mine excavations are often contrary to the means of preventing other ventilation-related hazards in the underground mine, e.g. the prevention of spontaneous combustion of coal in the goaf of longwall panel. Therefore, the design of longwall panels should be preceded by a detailed analysis of the results of both methane emission prediction and forecast of other ventilation-related hazards.

By Justyna Swolkień, Nikodem Szlązak, Dariusz Obracaj

Polish coal mines are characterized by severe geological conditions and the co-occurrence of natural hazards. These hazards are associated with methane and dust emissions during mining processes which can provide methane, dust or methane-dust explosions. Besides, there are such natural hazards as gas and rock outbursts, rock bursts, spontaneous combustion of coal and environmental heat load. The mutual influences of various geological conditions, as well as the natural hazards, intensify the increase of the methane explosion hazard. The occurrence of methane explosions in the Polish mining industry between 2013 and 2108 are analyzed. Fatal accidents are compared with similar events in the global mining industry. The methods of preventing the explosion hazard as well as methane emission control in the Polish coal mining sector are presented. Methane hazard prevention should be adapted to levels and other natural hazards, especially those related to ventilation of underground mine. The methods of preventing methane emissions into mine excavations are often contrary to the means of preventing other ventilation-related hazards in the underground mine, e.g. the prevention of spontaneous combustion of coal in the goaf of longwall panel. Therefore, the design of longwall panels should be preceded by a detailed analysis of the results of both methane emission prediction and forecast of other ventilation-related hazards.

By Galymzhan Karamyrzayev, Rashid Nadirov

Zinc ferrite ( ZnFe2O4) is a by-product of non-ferrous metal production and is considered a promising source of raw zinc. The most efficient way to extract zinc from its ferrite is via acidic extraction, specifically leaching by hydrochloric acid. A comparative study of synthetic zinc ferrite hydrochloric acid leaching in isopropanol, aqueous, and the mixed solvent was performed. Zinc ferrite was obtained by sintering a zinc and iron (III) oxide mixture. Crushed samples were subjected to leaching in 1 M HCl at 323, 333, and 353 K and pulp density of 1 g/100 mL. The dissolution of zinc and iron into solution in organic media reached 77% at 353 K, while in an aqueous environment this value was 65%. The activation energy of 70.0 kJ/ mol was found for the leaching process in an isopropanol environment, which is lower than that in an aqueous solution by 15%. The more efficient leaching effect of isopropanol is attributed to the lower dielectric constant of the alcohol which increases the affinity of chloride anions for zinc and iron cations at leaching.

Jun 5, 2022

By M. A. Barclay, D. Samson, A. M. Esteves

Several companies have adopted policies and standards aimed explicitly at increasing ‘local procurement’, recognising that local economic participation has benefits for companies and communities alike. From a corporate perspective, local economic participation is seen as one means of maintaining a social license to operate, as well as ensuring reliability of supply by having a supplier located nearby. From a community perspective, the participation of local businesses in the resource project is a means by which the benefits of resource development can flow into their communities. This paper is based on the research undertaken to produce a good practice guide for the mining, oil and gas sector. Our research revealed that the extent to which the local community will actually benefit from local procurement initiatives is dependent on the capacity of the community to supply goods and services to the project and, even more importantly, on its ability to adapt to the inevitable changes that accompany large-scale resource development. We provide guidance on adapting impact assessment tools to guide planning of procurement interventions.

Jan 1, 2011

By VASU GANGRADE, Marcia Harris, Kumar Vaibhav Raj, Jim Addis, Khaled Mohamed, Snigdha Sarkar

The National Institute for Occupational Safety and Health (NIOSH) conducted a ventilation assessment for a recently established underground room-and-pillar stone mine implementing split-mine ventilation. The primary objective was to examine the impact of the length of the in-place stone stoppings on face ventilation efficiency. These stone stoppings serve to separate the intake and exhaust entries and align with the mining direction. To achieve this, computational fluid dynamics (CFD) modeling was utilized. The appropriate turbulence model was selected, and a mesh convergence analysis was conducted for the CFD model. Following that, the CFD model was validated using the conducted ventilation surveys. Two configurations of in-place stone stoppings, designated as Layout-I and Layout-II, were simulated using the validated CFD models. Layout-I featured a shorter in-place stone stopping, while Layout-II had a longer one. The results obtained from the CFD models demonstrated that the increased length of the in-place stone stopping in Layout-II resulted in a notable enhancement in ventilation efficiency at the advanced faces (last stopping), elevating it from 4% in Layout-I to 8.4% in Layout-II. However, no significant impact of the in-place stopping layouts was observed at other faces. In general, Layout-II exhibited a greater circulation of air at the outby stoppings.

Feb 1, 2024

By Paul M. Godlewski, Gerry Millar, Harvey W. Parker

Recently, over 70 railroad tunnels in the western USA have been enlarged and rehabilitated "live track," utilizing modern excavation and lining methods, in most cases to clear the larger double-stack container cars. This paper presents the general conditions of the tunnels and the technical aspects and costs of the rehabilitation of approximately 40 kilometers of tunnels, which range in length from a few hundred meters to 13 kilometers. Concrete-lined tunnels were rehabilitated by grouting and rock bolting, while unlined or timber-supported tunnels were relined with shotcrete and rock bolts. High output lining methods were required because of limited track time. Enlargement has been accomplished primarily by carving notches out of the concrete linings with a roadheader, or occasionally with saws. Unlined tunnels were enlarged by drill-and-blast or roadheader excavation.

Jan 1, 1991

By J. J. Gusek, T. C. Richmond, R. W. Reisinger

A high-altitude (9,500-ft [2,900-m]) historic underground copper mine in Wyoming discharges neutral but copper-laden water into a pristine creek. Under a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) deferral agreement, the Wyoming Abandoned Mine Land Program performed site characterization and treatment studies in preparation for reclamation of the site. An integral part of the project included addressing the needs of a variety of interested and affected parties, including property owners, local populations, government agencies, and the media. This paper discusses an overall approach and specific methods employed to enlist public support for the project as well as some of the successes and failures experienced.

Jan 1, 2004

By Lana Alagha, Fardis Nakhaei, Jose L. Corchado-Albelo

Tellurium (Te), a critical mineral for solar energy technologies, faces supply risk challenges that drive the development of diversified and robust production routes. This research focused on improving Te enrichment from copper tailings (CT) produced from copper porphyry (CP) ores processing, addressing the loss of ~90% of Te minerals to tailings in the flotation process of CP ores. Gravity separation and froth flotation processes were used as possible enrichment routes of Te-bearing minerals (i.e., pyrite) in CT. In the froth flotation process, synergistic combinations of reagents were tested to achieve an acceptable enrichment ratio of Te minerals. Comprehensive characterization analyses showed significant Te enrichment in the flotation concentrates. Tellurium was recovered at 90%, while the grade of Te in the concentrates was 1.4 ppm using a xanthate collector and glycol frother compared to <0.5 ppm in the flotation feed. Findings showed that Te-minerals’ enrichment was also feasible in CT using the proposed combined concentrations routes (i.e., gravity separation followed by froth flotation) by looking at Fe, Cu, and S enrichment. This study also highlighted the importance of understanding the deportment of Te minerals in different process streams to develop and optimize efficient enrichment practices.

Feb 1, 2024

By S. K. Kawatra, T. C. Rao, J. P. Barnwal, Durga D. Patil

Coal macerals differ widely in their surface properties and in their hydrophobicities. Therefore, it is necessary to study the flotation time dependence of coal macerals using varying concentrations of various frothers and collectors. In the present study, froth flotation is used to explore the possibility of segregating coal macerals based on their relative rates of flotation. Petrographic analysis of the various macerals in the concentrate were carried out, and the results are expressed in terms of the recoveries of various maceral groups and mineral matter. Results show that it is possible to recover a good volume of the reactive macerals without mach loss of calorific value.

Jan 1, 2000

By Hazal Melis Aytac, Lana Alagha, Fardis Nakhaei

Gallium (Ga) and Germanium (Ge) are essential strategic elements that are extensively used as semiconductors in many technological fields. Owing to their essential uses and supply disruption, Ga and Ge are deemed critical by the U.S. They are typically found as substitutions or inclusions in zinc minerals. However, their distributions within zinc minerals are not well understood. To address this, trace element and mineralogy analyses of representative samples obtained from an old high-zinc-grade tailing were performed using various qualitative and quantitative techniques. These techniques included Inductively Coupled Plasma Mass Spectrometry (ICP-MS), Tescan Integrated Mineralogical Analysis (TIMA) with Scanning Electron Microscopy (SEM) and X-ray Diffraction (XRD). Moreover, bench-scale froth flotation tests were conducted to enrich zinc minerals, the major hosts of Ga and Ge, using PAX as a collector, Na2S as a sulfidizer, Pb(NO3)2 as an activator, and MIBC as a frother. Comprehensive characterization analyses of the flotation products showed significant enrichment of Zn, Ga and Ge in the flotation concentrates.

Feb 1, 2025