Search Documents

By R. R. Dorfler

The existing regrind circuit at the Climax Operations uses sodium cyanide and Nokes reagent to reject pyrite, copper, and lead minerals. Laboratory flotation studies were performed using feed to flotation following first-stage regrinding. The effects of conditioning time, pH, and the concentration of depressants such as Nokes reagent and sodium cyanide on the rejection of pyrite, lead, and copper minerals were investigated. The metallurgical results indicate that, in the presence of depressants, the rejection of copper is strongly dependent on the pH. Preliminary mill testing confirmed the finding. The rejection of impurities is also dependent on conditioning time. The recovery of molybdenite is independent of the variables investigated.

Jan 1, 1981

By David E. Thompson, Andrew F. McKown, Herbert H. Einstein, Amr S. Azzouz

INTRODUCTION Design of supports for underground chambers in rock has undergone considerable development. This becomes evident when comparing support dimensions of subway station caverns built in the U.S. over the past fifteen years. The Porter Square Station cavern, which is a part of the Massachusetts Bay Transportation Authority (MBTA) Red Line extension, is the latest in this series. It is approximately 168 m (550 ft) long, 21 m (70 ft) wide, and 14 m (45 ft) high, and has a permanent support of light steel ribs imbedded in a 0.4 m nominal (15 in) shotcrete lining. An extensive construction control instrumentation program made it possible to evaluate the performance of the cavern and its support. This evaluation, which is presented in this paper, was the objective of a research project sponsored by the Urban Mass Transportation Administration (UMTA) and jointly conducted by Haley and Aldrich, and MIT. The actually used design procedure was compared with other approaches, notably procedures based on Finite Element analyses and empirical rock mass classification methods. Support dimensions predicted with all these approaches were compared to the actual support and its performance.

Jan 1, 1983

By J. H. Rowland, R. A. Thomas, III, C. D. Litton

Atmospheric monitoring systems (AMS) are required when using air from conveyor belt entries to ventilate working sections in U.S. underground coal mines. AMS technology has the potential to increase fire safety mine-wide, but research is needed to determine the detection and response times for fires of a variety of combustible materials. To evaluate the potential of an AMS for fire detection in other areas of a coal mine, a series of full-scale fire experiments were conducted to determine detection and response times from fires of different combustible materials that are found in U.S. underground coal mines, including high- and low-volatility coals, conveyor belts, brattice materials, different types of wood, diesel fuel, and a foam sealant. These experiments were conducted in the Safety Research Coal Mine (SRCM) of the U.S. National Institute for Occupational Safety and Health (NIOSH) located in Pittsburgh, PA, using a commercially available AMS that is typical of current technology. The results showed that through proper selection of sensors and their locations, a mine-wide AMS can provide sufficient early fire warning times and improve the health and safety of miners.

Jan 1, 2016

The Department of Health and Human Services (HHS), National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), with the assistance of cooperating underground mining operations and state agencies, has conducted research exploring devices and technologies that could be used to assist miners navigating through smoke and dust resulting from a fire or explosion. Recent events in mines confirm that smoke and dust can enter and contaminate mine escapeways creating an atmosphere with severely reduced visibility. This reduced visibility results in substantially increased escape times, possible disorientation or confusion, and increased stress levels, and may prevent evacuation altogether. Tools or devices that assist miners in navigating through smoke-filled areas void of lifelines could make the difference in successful escape from the mine. This paper presents the results of OMSHR research to identify and evaluate tools and devices that could provide meaningful information to evacuating miners in areas with limited visibility and without the benefit of a lifeline.

Jan 1, 2011

By C. J. Slaughter, S. P. Harteis, L. L. Chasko, D. W. Alexander

The Department of Health and Human Services (HHS), National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), with the assistance of cooperating underground mining operations and state agencies, has conducted research exploring devices and technologies that could be used to assist miners navigating through smoke and dust resulting from a fire or explosion. Recent events in mines confirm that smoke and dust can enter and contaminate mine escapeways, creating an atmosphere with severely reduced visibility. This reduced visibility results in substantially increased escape times, possible disorientation or confusion, and increased stress levels, and may prevent evacuation altogether. Tools or devices that assist miners in navigating through smoke-filled areas void of lifelines could make the difference in successful escape from the mine. This paper presents the results of OMSHR research to identify and evaluate tools and devices that could provide meaningful information to evacuating miners in areas with limited visibility and without the benefit of a lifeline.

Jan 1, 2011

By Robert A. Haney, Scott G. Vail, Kenneth G. Fields

The Mine Safety and Health Administration, in cooperation with IMC Global Operations, Inc., conducted a joint study to determine the effectiveness of the technology currently in use at the mine to control diesel particulate exposures. IMC Global operates an underground potash mine using diesel-powered equipment to extract minerals. IMC uses a variety of technologies to control worker exposures to diesel particulate. These technologies include: ventilation, low sulfur fuel, oxidation catalytic converters (OCC), maintenance and work practices. The study was conducted over a two-week period, two shifts per day. During the first week (six shifts), baseline data on exposures and diesel particulate emissions were obtained. New OCC's were installed over the weekend on all equipment on the test section. During the second week (six shifts), data were collected to assess the effectiveness of the new OCC devices. In addition to exposure and diesel particulate emissions data, mine ventilation, engine exhaust temperatures and mine operational data were obtained. The primary means of determining diesel particulate concentrations was the respirable combustible dust (RCD) method. Gas concentrations carbon monoxide (CO), carbon dioxide (CO,), and nitrogen dioxide (NO,) were measured using passive dosimeter badges and gas bottles. Results of measurements of diesel particulate, gases, and air- flows were analyzed to determine the effectiveness of airflow and oxidation catalytic converters for controlling diesel particulate exposures. The use of oxidation catalytic converters resulted in reductions of both workers' exposures and diesel emissions.

Jan 1, 1997

By S. Mischler, J. Noll, G. Schnakenberg, A. Bugarski, M. Crum

Diesel particulate filter (DPF) systems and biodiesel fuels are two of the most promising technologies available to the mining industry to reduce the exposure of underground miners to diesel particulate matter (DPM). A study has been conducted to estimate the potential of DPF systems and biodiesel blends to reduce DPM emissions from production vehicles. Results of testing three DPF systems in an isolated zone showed 88% to 99% reductions in elemental carbon concentrations. The test results also show that biodiesel blends, B20 and B50, reduced the elemental carbon concentrations in the mine air by 26 and 48 percent, respectively.

Jan 1, 2004

By L. Yuan, J. H. Rowland, R. A. Thomas

"Hydrogen (H2) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system (AMS). In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, constant H2 concentrations in the airflow, from 100 to 500 ppm, pass through sensors. While in the full-scale experiments, increasing H2 concentrations generated as a byproduct from charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to ensure the safeguard of underground miners. INTRODUCTION As many types of battery-powered mining equipment such as scoops and shield haulers are used in underground mining operations, charging stations are required to charge the equipment batteries. These batteries are of lead acid chemistry. A safety issue exists with the battery charging stations as all lead acid batteries produce flammable H2 gas during the normal charging process. Overcharging or excessive heat can quickly cause batteries to produce even more H2. If H2 is not appropriately diluted or dispersed, it builds up, and the risk of fire and explosion increases. Mine Safety and Health Administration (MSHA) regulation (30 CFR Part 75.340) requires that battery charging stations should be housed in noncombustible structures or be equipped with a fire suppression system. When a fire suppression system is used, the battery charging stations must be ventilated with intake air that is directed into a return air course or ventilated with intake air that is monitored for CO or smoke using an AMS. The monitoring of intake air ventilating battery charging stations should be done with sensors that are not affected by H2."

Jan 1, 2018

By L. Yuan, J. H. Rowland, R. A. Thomas

Hydrogen (H2 ) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system. In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, H2 concentrations in the airflow are constant, while in the full-scale experiments, increasing H2 concentrations generated as a byproduct of charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to safeguard underground miners.

By Richard A. Thomas, Liming Yuan, Lihong Zhou, James H. Rowland

Hydrogen (H2) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system (AMS). In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, constant H2 concentrations in the airflow, from 100 to 500 ppm, pass through sensors. While in the full-scale experiments, increasing H2 concentrations generated as a byproduct from charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to ensure the safeguard of underground miners.

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By S. R. LaBrooy, J. Avraamides

Thermal reactivation of eluted carbon is an essential part of most carbon-in-pulp gold recovery plants. The effectiveness of the reactivation procedure depends on the nature and level of contaminants adsorbed on the carbon, the efficiency of the elution and the temperature, residence time and atmosphere within the kiln. The most commonly used kilns are evaluated in terms of their operating parameters and performance. Data obtained both in the laboratory and in the field emphasize the importance of carbon feed moisture content, kiln atmosphere and carbon conditioning on the activity of the kiln product.

Jan 1, 1998

By J. Noll, C. DeGennaro, C. Zhou, J. Srednicki

"The personal dust monitor (PDM) (model PDM3700), as well as other electronic devices, can cause electromagnetic interference (EMI) which can disrupt the operation of some proximity detection systems (PDSs). A 15 cm (6 inch) minimum separation distance between the miner-wearable component (MWC) of the PDS and the electronic device usually avoids these disruptions, but due to the amount of equipment on a miner’s belt and the method of wearing the PDM in some situations, this distance can be difficult to always reliably maintain. Another method of reducing EMI effects is utilizing magnetic field shielding. The shielding capability of several different materials was investigated by surrounding the PDM with the material and quantifying the EMI. A copper mesh pouch reduced the EMI from a PDM3700, allowing a minimum separation distance of 10 cm (4 inches) instead of 15 cm (6 inches) as shown in a previous study for an unshielded PDM. A MU-metal box had a better shielding effectiveness, as it further reduced the minimum separation distance to less than 7 cm (2.8 inches). Shielding reduced the EMI of the PDM with MU-metal providing better results than the copper mesh. These materials may be beneficial for shielding individual components of the PDM or for constructing a shielded pouch. However, before the advantages of a shielded pouch can be determined, the effects of just the shielding material (metal) on the PDS needs to be quantified. INTRODUCTION According to statistics from the Mine Safety and Health Administration (MSHA), 43 miners have been fatally struck or pinned by a continuous mining machine (CMM) since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems (PDSs) have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (MSHA, 2015)."

Jan 1, 2018

By Robert A. Haney, David J. Atchison, Kenneth G. Fields

Mining systems with greater than a 20-foot face advance (deep cut) have become popular due to their increased productivity and safety. The face dust collection system used in many of the mines employing the deep cut systems, incorporates a machine mounted dust collector with either a blowing or exhausting line brattice and a remote control operated continuous miner. In order to characterize and quantify the parameters used to control dust with these systems, the Dust Division conducted studies on four mining sections using continuous miners with deep cut mining systems. On each section, the dust control system incorporated line brattice with a machine mounted dust collector. The remote control made it possible for the continuous mining machine to advance further while permitting the operator to remain under supported roof and away from dust generated during mining. The purpose of these studies was to evaluate the effectiveness of deep cut mining systems using dust collectors to control respirable dust exposure. This paper summarizes the results of the studies conducted. At each mine face workers were sampled to determine their full-shift dust exposure. Additionally, fixed point dust samples were collected at various locations to determine relative concentrations of dust generated from mining. Air quantities were measured at each working place to determine the amount of air delivered to the face area. Evaluations were made by comparing worker exposures to respirable dust samples taken at appropriate locations upstream and downstream of the coal faced being mined. An estimate of the amount of the respirable dust being generated at the face during mining and the amount of respirable dust being removed by the dust collectors was made by balancing the air quantities and the dust concentrations immediately upstream and downstream of the coal face. Results of the studies showed that the dust control systems, were effective for controlling workers exposure to respirable dust. Dust collector efficiencies were determined to be approximately 85 percent. While the dust collectors were effective in removing respirable dust, the success of the systems with line brattice greater than twenty feet from the face, was dependent on the use of the remote control which permitted the continuous miner operator to remain out of the high concentration dust cloud in the working face. Dilution from intake air, combined with the dust collector efficiency, maintained exposure of other section workers below applicable standards.

Jan 1, 1991

By T. W. Beck

Overexposure to respirable dust remains a widespread health hazard to roof bolter occupations in underground coal mines. Recently implemented mist drilling technology was evaluated for its effectiveness in controlling respirable dust exposures for roof bolting personnel. This work presents the findings from NIOSH field and laboratory studies comparing respirable dust levels on mist drilling roof bolter machines to dust levels measured on machines using a conventional vacuum drilling system. Gravimetric and instantaneous respirable dust samples were collected for multiple drilling cycles. These dust measurements were used to assess the potential dust control capabilities relative to conventional drilling. Controlled laboratory tests found 0.3 mg/m3 more respirable dust with mist drilling than with the conventional vacuum method. A separate field investigation of the two techniques observed higher dust levels around the mist bolting machine.

Jan 1, 2008

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau ofMines (USBM) have given a significant effort over the past four decades in researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers performing manual bagging and palletizing of 50- to 100-pound bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper will provide an overview of available dust control technologies for bagging operations and present the findings of a recent case study that was conducted at four different industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation will also be performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

Apr 3, 2020

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The U.S. National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau of Mines (USBM) have put significant effort over the past four decades into researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers who perform the manual bagging and palletizing of 50- to 100-lb bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper provides an overview of available dust control technologies for bagging operations and presents the findings of a recent case study conducted at four industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation is also performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

By Dennis A. Beiter, Kenneth G. Fields, Richard T. Stoltz

Section 56.5001 Title 30, [Code of Federal Regulations1], establishes requirements for respirable dust exposure in Metal and Nonmetal Mines based on the Threshold Limit Values (TLV's) adopted by the American Conference of Governmental Industrial Hygienists. Respirable dust samples collected by Mine Safety and Health Administration (MSHA) inspectors at a sandstone quarry showed certain workers were exposed to excessive concentrations during development of a "coyote tunnel" that was ventilated with a blowing system. Because exhausting face ventilation systems are known to control dust more effectively than blowing face systems, a change was proposed to improve worker respirable dust exposures. This paper describes the evaluation of the proposed exhausting ventilation system in the quarry's "coyote tunnel" and compares the respirable dust exposures with those measured by the MSHA inspectors with the blowing system. Results showed the proposed exhausting ventilation system reduced respirable dust exposures to less than 20 percent of those measured by MSHA inspectors when the blowing system was used.

Jan 1, 1993

'IM existing predictive methods were chosen for evaluation; an influence function (Bals Theory) and a profile function (hyperbolic). These ere applied to several field measured subsidence profiles over United States coal mines. The effect of homogeneous versus non-homogeneous overburden on surface subsidence is demonstrated and the utilization of Bals Theory as a subsidence predictive method for both types of overburden is examined. The major factor affecting subsidence profile characteristics is the migration of the inflection point toward the centerline of the longwall panel. A computer program was written to aid in the analysis.

Jan 1, 1982