Search Documents

By Mark Van Dyke, Ted Klemetti, Jake Beale, Zoheir Khademian, Joe Wickline

In 2016, a 3.7-ML magnitude event caused by mining activity occurred at a longwall mine in southwestern Virginia which was recorded by the United States Geological Survey (USGS) and felt by local residents. The event was the largest of its kind since a global mine design change by the operator was instituted in 2008 following three large events in 2005, 2006, and 2007 (3.4, 4.3, and 3.4 Moment Magnitude (Mw), respectively). Two of the three pre-2008 events (2005 and 2007) damaged ventilation controls in the mine which fueled a mine fire. In 2016, the mine’s management requested researchers from the National Institute for Occupational Safety and Health (NIOSH) to access geological data and determine what parameters could possibly lead to events of a magnitude of 1.0 ML or greater. Evaluation of 2152 geological data points and modeling revealed three major geological factors in common with the majority of the 181 recorded +1.0 ML events from 2009 through 2016. Three levels of seismic potential were identified as follows:

Aug 4, 2023

By I. Ehie, Y. P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15% to a maximum depth of 46 m (150 ft). Pit orientations along the true dip (dipline), along the strike (strikeline), and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas and also to furnish data for the computer simulation models. A dragline microsimulation, a shovel/truck simulation, and a surface mine cost analysis models were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and seam pitch. The productivity (m3/h) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity. Larger size trucks were preferable to smaller size trucks in the pit con¬figuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip for the mining condition studied.

Jan 1, 1987

By C. D. Litton, I. E. Perera

This report presents the results of experiments to evaluate different types of mine fire sensors in an underground mine environment using a commercially available atmospheric monitoring system. To determine how well carbon monoxide (CO) and smoke sensors respond for purposes of fire detection, experiments were conducted using test fires of different mine combustibles and for both flaming and nonflaming combustion. The experiments were designed to assess the response of fire sensors to different contaminants and different contaminant levels produced from the test fires. The experiments were performed in the Safety Research Coal Mine at the U.S. National Institute for Occupational Safety and Health’s Bruceton Research Facility in the presence of an average ventilating air velocity of 1.6 m/s (315 fpm). Five fire sensor stations were located downstream of the test fire at fixed locations, with each sensor station consisting of four sensors: a CO fire sensor and three different smoke sensors, of which two were evaluated by the Mine Safety and Health Administration (MSHA) for intrinsic safety and the third was used extensively in underground mines overseas but not evaluated by MSHA for intrinsic safety. All four sensors were mounted near the center of the entry and in the upper onethird of the entry height. A UL-listed combination ionization and photoelectric smoke sensor was mounted near the roof at the first sensor station and its responses were compared against the responses of the four CO and smoke fire sensors. Sensor response data, contaminant travel times, and the impact of fire on the existing ventilation flow are discussed as they apply to earlywarning fire detection. Of significance in the analysis is the need for performance standards for mine fire sensors in order to provide for consistent and timely early warning of developing fires.

Jan 1, 2014

By Lynn Salvati, Colin LaVassar, Loic Galisson, Joel Theodore, Lynette Sla

"Sound Transit’s University Link and Northgate Link projects will add 6.75 miles (10.9 km) of twin-bored tunnel to Seattle’s light rail system, extending the route north from downtown Seattle. The tunnels are being constructed primarily in glacial soils using pressurized-face tunnel boring machines. Cover over the tunnel alignment varied from 13 feet to over 300 feet (4–91 m). Since the tunnels are located in densely populated urban areas, controlling ground movements and monitoring settlement were essential to success of these projects. Hundreds of geotechnical instruments, including extensometers, surface settlement points, and near-surface settlement points, were used in both projects to monitor settlement. The observed data were compared to settlement predictions made prior to tunneling, and analyses performed to update empirical factors to better estimate settlements. Recommendations for designing efficient and cost-effective settlement monitoring programs are provided based on the review of the monitoring data and analyses.INTRODUCTIONThe paper includes data from Sound Transit’s University Link and Northgate Link projects. These projects will add 6.75 miles of twin-bored tunnel to Seattle’s light rail system. The tunneling for University Link will extend the light rail system from downtown Seattle to the University of Washington. Tunneling from downtown Seattle to the Capitol Hill Station was completed under the U230 contract, and tunneling from the Capitol Hill Station to the University of Washington Station was completed under the U220 contract. The Northgate Link extension will extend the light rail line north of the University of Washington, including approximately 3.5 miles (5.6 km) of twin tunnels between the University of Washington Station and the Maple Leaf Portal and two stations, U District Station and Roosevelt Station. Tunneling for the Northgate Link project is still underway as part of the N125 project. At the time of writing, tunneling from the Maple Leaf Portal to Roosevelt Station has been completed. Therefore data labeled as N125 in this paper only include the portion of the alignment from the Maple Leaf Portal to Roosevelt Station."

Jan 1, 2016

By S. S. Peng

Since the introduction of shield supports in 1975, safety and production in U.S. longwall faces have improved considerably. Many faces had a daily production of up to 8,000-10,000 tons and productivity reached 600 tons per man-shift. But a longwall face requires expensive equipment which slows down the growth rate of the percentage of longwall production. Among the equipment cost the shield support accounts for 50-60%, a very large proportion. Therefore, it will have a large impact on the growth of longwall mining in the U.S. to reduce the support cost (1).

Jan 1, 1988

By O. A. Orumwense

The liberation of intimately disseminated impurities from the coal matrix often demands that the material be ground to a high degree of fineness. Similarly, some technologies for coal utilization require superfine particles (i.e., sizes less than ten microns). This implies additional costs for coal preparation plants due to the high energy and media costs associated with fine grinding operations. Besides, there are problems such as sever product contaminations due to media wear and impairment of the quality of coal. Hence, proper choice of grinding media type is important from the viewpoints of cost reduction and product quality.

Jan 1, 1993

By William E. Mead

The process of selecting a building site for a major structure is a complex procedure involving the consideration of a multitude of factors. The approximate geographic location for a structure is usually fixed by its intended function, though often there may be several site alternatives. Socio-economic, logistic, marketing and political factors are the primary site determinants. Also critical in site planning, however, are the environmental factors, both natural and man-made. These factors will influence the precise siting location within the limits allowed by the primary determinants and will dictate some of the basic design criteria. This paper discusses environmental factors, principally those which are natural conditions, that must be analyzed for five different groups of structures. The importance of thorough site environmental analysis based upon the principles of applied earth science is described. Significant elements to be considered in an appraisal of the geology, hydrology, seismology and meteorology are outlined.

Jan 1, 1968

By I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke, and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale Fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL) in Fairchance, PA, using Ponderosa Pine, Red Oak, Douglas-fir, high and low volatile coals, PVC and SBR conveyor belt, No. 2 diesel fuel, and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector, and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations, and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (1). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters? Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2012

By C. D. Litton, I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory in Fairchance, PA, using ponderosa pine, red oak, Douglas fir, high and low volatile coals, polyvinyl chloride (PVC) and styrene butadiene rubber (SBR) conveyor belts, No. 2 diesel fuel and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters, producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (Litton et al., 1991). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters’ Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2014

By C. D. Litton

Laboratory experiments were conducted to determine the responses of a prototype smoke detector and a commercially available photoelectric smoke detector to smoke particles generated from various combustion sources. The prototype smoke detector combines optical scattering measurements with ionization chamber measurements in order to reduce/eliminate nuisance alarms due to the presence of airborne dusts or diesel exhaust particles. The commercially available smoke detector is designed for use in harsh environments where airborne dust represents a major problem due both to nuisance alarms and detector contamination. In the experiments, the responses of the two detectors were measured when exposed to smoke particles from the exhaust of a diesel engine and from a variety of fire sources, including wood, coal, styrene butadiene rubber, and No. 2 diesel fuel. For the solid fuels, data were obtained for both smoldering and flaming combustion. This report describes the experiments, their results, and the use of these results as they apply to early-warning fire sensors capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by either airborne dust or the products produced from diesel engines. Subsequent to these laboratory experiments, six smoke detectors were installed in an underground limestone mine for further testing and evaluation. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Scott Thayer, Michael Murphy, Natalie Cope, Gabriel Esterhuizen, Anthony Iannacchione, Tim Miller, Brent Slaker

"The Subtropolis room-and-pillar mine extracts the Vanport Limestone (Allegheny Formation, Pennsylvanian System) near Petersburg, Ohio. Strata instability problems associated with excessive concentrations of lateral stress caused the mine operator to implement a change in layout design. This mining method has been identified as a stress control layout, which has been used by other underground stone mines in the past with varying degrees of success. Practical experience has shown that entry headings advance in the direction of the principal lateral stress, producing lower stress concentrations with better mining conditions. It is important to minimize stress concentrations along the mining front, so an arrow-shaped advance is recommended. This technique advances more developments (headings) in a “good” direction and reduces developments (crosscuts) in a “bad” direction. As is expected, the stress control layout enhances the potential for shear failures in crosscuts. It is, therefore, important to focus crosscut engineering interventions that either: (a) lower stress concentrations (for example, an arched roof) or (b) enhance strength of the strata containing the shears (for example, rock reinforcement). This study focuses on observing strata conditions on a regular basis and monitoring the response of this strata to changing geologic and mining conditions through 3D Dynamic LiDAR scans.INTRODUCTIONProject AimsThe Subtropolis Mine is extracting the Vanport Limestone in northeastern Ohio. Since the start of mining in 2006, ground conditions have been significantly affected by excessive lateral stress condition. In some other mining districts with this hazard, certain mine layouts have been shown to lessen the potential for unstable ground conditions. The term “lessen” is used to state the realization that stress concentrations are not eliminated but instead occur in less frequency and intensity, and their locations can be projected.The stress-control mine layout, specifically for large-opening room-and-pillar stone mines, naturally evolved at mines suffering from excessive lateral stress problems. These mines will typically experiment with methods to mitigate adverse impacts, thus developing best practices for their conditions. These practices have evolved into a basic framework for the stress control mine layout. For example, Jack Parker was able to write about personal experiences at the White Pine Mine in Michigan (Parker, 1966, 1973). Various researchers at the U.S. Bureau of Mines (USBM), the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and Health (NIOSH) have studied the effectiveness of stress-control mine layouts over a wide range of geologic conditions (Emery, 1964; Mark and Mucho, 1994; Iannacchione et al., 2003). While the stress control layout design approach has proven successful in many categories, it can be difficult to implement. For example, excessive stress conditions in crosscuts can put the ground control focused intervention at odds with ventilation and haulage constraints, thus limiting optimal crosscut size, shape, and location. Therefore, more information on the effectiveness of this approach is needed."

Jan 1, 2019

By A. B. Szwilski

The mineability and coal processing costs are influenced largely by the structural and physical properties of the coal seam. The mining process involves coal cutting, pillar support, crushing, and floating. A correlation between the rank, ash content, and coal strength/stiffness is discussed. The coefficient of variability of rebound tests on the face of various coal seams are compared with those of laboratory compressive strength tests by other investigators.

Jan 1, 1988

By Tony Szwilski

A correlation between the rank, ash content and coal seam discontinuities and coal strength/stiffness is discussed. Rebound hammers were used to evaluate the strength properties of two coal seams. The coefficient of variability of the rebound tests are compared with those of laboratory compressive strength tests by other investigators.

Jan 1, 1985

By Dennis Z. Mraz

Subsidence profiles over Saskatchewan potash mines exhibit forms which cannot be explained by existing subsidence models. The subsidence is affected by bridging of competent rocks. A modification of the theory can explain the observed displacement of subsidence profiles due to bridging. An unusual shallow secondary subsidence trough has been observed extending two to three kilometers outside the primary subsidence. The secondary subsidence is explained as an elastic compression inresponse to a drop in pore water pressure in the vicinity of the caving zone. The concept of pore water pressure may lead to a safe extraction limit for Saskatchewan mines.

Jan 1, 1986

By M. Nehdi

Deficient surface disposal systems of sulfidic mine waste often cause severe contamination of surface streams and groundwater reservoirs due to the oxidation of sulfide phases. The subsequent generation of leachates characterized by high acidity and elevated concentrations of toxic elements (commonly known as acid mine drainage) jeopardize the health of contiguous ecosystem. Stabilization/solidification (S/S) is recognized as a promising solution for treating such wastes. S/S processes generally mobilize alkaline and/or cementing materials/additives that act as neutralizing and/or binding agents. In the present research, industrial byproducts, namely, cement kiln dust (CKD) and Class C fly ash (FAC) have been used as candidate materials along with the partial addition of sulfate-resistant cement (SRC) in the S/S of polymetallic sulfidic mine tailings (MT). The effectiveness of S/S was assessed by comparing laboratory experimental values obtained from unconfined compressive strength, hydraulic conductivity and leaching propensity tests of S/S samples with regulatory standards for safe surface disposal of such wastes. Despite general regulatory compliance of compressive strength and hydraulic conductivity, some solidified/stabilized-cured matrices were found unable to provide the required immobilization of pollutants. Solidified/stabilized and 90-day cured mine tailings specimens made with composite binders containing (10% CKD + 10% FAC), (5% SRC + 15% FAC) and (5% SRC + 5% CKD + 10% FAC) significantly impaired the solubility of all contaminants investigated and proved successful in fixing metals within the matrix, in addition to achieving adequate unconfined compressive strength and hydraulic conductivity values, thus satisfying U.S. EPA regulations. Laboratory investigations revealed that, for polymetallic mining waste, leachate concentrations are the most critical factor in assessing the effectiveness of S/S technology.

Jan 1, 2008

By M. S. Safarzadeh

Over the last fifty years, the treatment of enargite concentrates has not received much attention primarily because of the availability of other clean concentrates suitable for processing with existing smelting and/or leaching technologies. As traditional copper ores have become scarcer, copper-arsenic ore deposits have garnered more interest. Arsenic release is a significant concern during the treatment of enargite by pyro or hydrometallurgical methods. Enargite is also very refractive in standard leaching procedures. Thus, economical treatment options for enargite concentrates are needed. Preliminary experiments have shown that the acid-bake leach process could be adapted and used for the treatment of enargite concentrates. In this study, low-temperature (100-400 ºC) sulfuric acid baking of an enargite concentrate followed by water-leaching has been evaluated. The results indicate the thermal transformation of enargite to copper sulfate during sulfuric acid baking, with most of the arsenic being released from the concentrate into the gas phase for baking at 400 ºC. The condition for maximum copper extraction (~100%) from the concentrate was found to be 400 ºC, sulfuric acid amount of 0.5 mL/g of concentrate, and 2 h baking time. Part of the arsenic was captured in the form of arsenopyrite (FeAsS). XRD analysis proved the presence of some arsenic in the form of claudetite (As2O3) in the baked concentrate. Acid baking of pure enargite behaved in similar fashion.

Jan 1, 2012

By M. S. Safarzadeh

Over the last fifty years, the treatment of enargite concentrates has not received much attention, primarily because of the availability of other clean concentrates suitable for processing with existing smelting and/or leaching technologies. As traditional copper ores have become scarcer, copper-arsenic ore deposits have garnered more interest. Arsenic release is a significant concern during the treatment of enargite concentrates by pyro or hydrometallurgical methods. Enargite is also very refractive in standard leaching procedures. Thus, economical treatment options for enargite concentrates are needed. Preliminary experiments have shown that the acid bake-leach process could be adapted and used for the treatment of enargite concentrates. In this study, low-temperature (100-400º C) sulfuric acid baking of an enargite concentrate followed by water leaching has been evaluated. The results indicate the thermal transformation of enargite to copper sulfate happens during sulfuric acid baking, with most of the arsenic being released from the concentrate into the gas phase when baking at 400º C. The condition for maximum copper extraction (~100%) from the concentrate was found to be 400º C, a sulfuric acid concentration of 0.5 mL/g and two hours baking time. Part of the arsenic was captured in the form of arsenopyrite (FeAsS). X-ray diffraction (XRD) analysis proved the presence of some arsenic in the form of claudetite (As2O3) in the baked concentrate. Acid baking of pure enargite behaved in a similar fashion.

Nov 1, 2011

By R. N. Chakravorty

It is well established that coal can react with oxygen in air at ambient temperature and as a result heat is produced. If the heat is not fully dissipated the temperature of the coal mass will increase, thereby enhancing the rate of oxidation with a greater production of heat. If this phenomena continues, the coal mass can ignite under favourable heat accumulation conditions. A number of mine fires are caused each year due to this phenomena, commonly known as spontaneous combustion. The early detection of spontaneous combustion is of prime importance to mining engineers since any fire which could be detected at an early stage may save the mine from considerable damage and subsequent loss of production. Obviously, there is no single general criteria by which one can assess whether the under- ground mining of a coal seam will result in liability to spontaneous combustion. This has made it imperative to develop systems for the early detection of heating and to follow its development. In recent years considerable advances have been made in the design and development of methods for the early detection of spontaneous combustion. The Mining Research Laboratories (CANMET) is presently investigating the problem of spontaneous combustion in coal mines with Kaiser Resources Ltd. at their hydraulic mine at Sparwood, B.C. on a co-operative basis, and some of the work was described earlier in the Canadian Institute of Mining & Metallurgy Bulletin (1,Z). This paper summarizes and updates the work done by CANMET on the detection of spontaneous combustion in coal mines.

Jan 1, 1980

By Dennis Dolinar

Improperly designed support systems have led to unplanned roof falls in longwall tailgates. To prevent such falls requires appropriate support and adequately designed support systems. The National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. To design the support system with this methodology requires a quantitative assessment of the ground and support interaction, which is developed from instrumented test sites installed in longwall tailgates. To compliment and expand the field data results and to optimize the support design, numerical modeling is also conducted. The models are calibrated from the test site data. In the present study, data was obtained from a longwall tailgate in the Illinois basin. The test site was located in the Herrin No. 6 coal seam at a depth of 500 ft. At the site, the immediate roof was a weak shale overlain by a competent limestone. Above the limestone, sandstone formed the intermediate roof. The floor consisted of a weak underclay. In the study, the performance and interaction with the surrounding rock mass of two different standing supports, an engineered crib and a conventional 4-point wood crib were monitored. The two cribs have similar load-displacement characteristics at least through 6 in of displacement. Beyond 6 in, the engineered crib becomes unstable and begins to strain soften and shed load. The measurements and developed ground reaction curves indicated that the tailgate at the mine was a low convergence environment until well inby the face. Because the convergence was well below their capacity, both supports provide more than adequate levels of support to the tailgate. Significant convergence and support loading did not occur until 90 to 100 ft inby the face. The results of this study were also compared with results from similar studies conducted in the Pittsburgh seam to further advance the development of the ?ground reaction curve? based support system design.

Jan 1, 2009

Instabilities occurred as a result of climate changes caused to investigate the rock behavior dependency to temperature changes, in this paper. In the natural earth condition, the phase transition of pore water has known to be the most effective factor causing different rocks mechanical properties due to temperature changes. So, the temperature range of [-30, 30]°C is selected in laboratory tests of this study. P-wave velocity, unconfined compressive strength (UCS) and elasticity modulus of rocks at different temperatures are studied by developing a temperature adjusting apparatus. The tests were performed on three rock types. The results show that firstly, the temperature reduction and pore fluid freezing improves these rock?s mechanical properties. Secondly, the dependency of rock properties to climate changes depends on the type and shape of its porosity as well as porosity percent. The improvement of rock mechanical properties in jointed rocks exceeds rocks with spherical pores. Finally, maximum changes in rock?s properties occur at [-10, 0]°C, which includes the phase transition of pore fluid. Keywords: Temperature; Rock Mechanical Properties; Pore Fluid; Porosity.

Feb 27, 2013