Search Documents

By Boris V. Vlasenko, Vadim P. Potapov, Gennady I. Gritsko

In this paper we consider the elements of an information geomechanic monitoring system which is used in computerized mine planning and mining operations control. The automated sys tem is a technical means of geomechanic monitoring, as a complex system of regulated observations, estimation and prediction of changes in geomechanic state of rock mass and workings during underground mining of coal deposits. Geomechanic monitoring at coal mines and the automated system execute data collection, analysis and calculations of geomechanic situation in the panel during planning, development and carrying-out of mining operations for ensuring geotechnical stability of underground mining.

Jan 1, 1996

By D. D. Snyder, J. D. Bode, F. T. King

INTRODUCTION Only in recent years have the environmental hazards associated with mining and tunneling operations been fully acknowledged and determined remedial action undertaken. The nature of these excavation operations leads to a wide diversity of hazards spanning mechanical, electrical, chemical, environmental, and physiological. The most insidious of these are unquestionably the environmental ones which have the greatest long-term effect and are the most difficult to pinpoint and monitor. It is the atmospheric contaminants that lead to a significantly greater illness and mortality rate among miners. Dust is the most prevalent, hence most important of the atmospheric contaminants. Respirable particles lead to diseases characteristic of many mining operations: coal workers pneumoconiosis, asbestiosis, silicosis, talcosis, anthrocosis, etc. But toxic and suffocating gases can be equally insidious and the most innocuous pollutant, methane, leads to the most imminently disastrous results of all - explosion and fire. This means that truly effective monitoring of the environmental hazards in tunneling cannot be limited to a few simple standard check measurements. It must include the most precise measurements we can make for specific, documented hazards and even for factors, such as noise and heat stress, not immediately obvious as hazards. The Federal Metal and Nonmetallic Mine Safety Act and more recent Occupational Safety and Health Administration standards are clearly designed to match such effective monitoring. We must, therefore, consider not only presently available monitoring instruments and those currently under develop-

Jan 1, 1997

By Allan Gebhard

The purpose of this paper is to summarize the role of water resource monitoring in mining activities and to discuss the considerations that go into designing and implementing a monitoring program. The design of a monitoring program is invariably based on sound engineering and scientific judgement since no design formulas exist that can be universlly applied to the monitoring of all activities. As discussed in this paper, however, a methodology of designing a water resource monitoring program does exist. In order to cost-effectively monitor the water resource impacts of mining activities, the following three monitoring related items should be understood: 1. the role of water resource monitoring in the planning, construction, and operational stages of mine development, 2. the available water resources monitoring methods and the proper role of each method in the various scages of mine development, and 3. the strategies that should be followed in designing and implementing a water resource monitoring program.

Jan 1, 1976

By A. Probst, N. Moores, J. A. Finch

In 1994, McGill University and INCO Ltd. (Sudbury operation) initiated the transfer of technology originally developed to detect levels in equipment ranging from flotation columns to thickeners. A conductivity probe was installed in a concentrate thickener to monitor the mud line and the solids load. The probe consisted of a vertical tube with 32 equally spaced electrode rings connected in pairs to give 31 conductivity cells. Conductivity was measured as a function of depth to produce a conductivity profile. From the conductivity profile, the mud line and the percent solids can be inferred. The probe was installed in October 1994, and it has been successfully detecting profiles since then. This paper includes a description of the incidents that occurred and the experiences gained during this technology-transfer process. Discussed is probe installation and startup; software modifications to accommodate both operating conditions and the needs of the operators; and calibration procedures to adjust to changes in performance as a consequence of long-term use. Also included are preliminary observations of the still-in-progress last stage, i.e., signal interpretation and use to facilitate operation, particularly by providing early reaction to upstream disturbances.

Jan 1, 1999

By M. Perolo, A. Contini, E. Ramelli, G. Borgonovo, L. Locatelli

This paper presents the ground settlement monitoring system used during the construction of two tunnels bored by two EPB TBMs, beneath the existing and active railway embankment in Bologna (Italy). The tunnels run close to large buildings and beneath bridges and other infrastructure. Data are collected from remote total stations and from electro levels installed directly on the railway tracks. The automated monitoring system acquires and analyses data then sounds an alarm in the event that there is a problem. Alarms are sent out in case of excessive tilt or settlement. Data is provided through a dedicated web application for multiple-party access, to gather, manage and store monitoring data.

Jan 1, 2007

By M. F. Werneke

Flotation of the carbonate, oxide and silicate minerals of copper (malachite, azurite, chrysocolla) has been the subject of much research in recent years, but few effective solutions to this problem have been found. With decreasing reserves of sulfide minerals, the economic recovery of these "oxides" appears to be an important source of copper for the future. Xanthates have been known for many years to be malachite collectors (1), but only at very high dosages, or at lower dosages following activation of the mineral by sulfide ion. Dewitt and Batchelder (2, 3) found that chelating agents such as certain oximes were collectors for malachite and azurite, but also required high reagent dosages. Fuerstenau (4) has suggested, for example, that potassium octylhydroxamate may be an effective collector for malachite, On the other hand, Balberyszski (5) has found that oxide minerals may be completely sulfidized at high temperatures with gaseous sulfur or H2S, and then floated with conventional collectors. None of the above approaches appear to offer an economically effective method for the direct flotation of these oxide minerals.

Jan 1, 1977

By Don Muraoka

Soda ash, anhydrous sodium carbonate, is produced from underground trona deposits occurring in the Green River Sasin of Southwestern Wyoming. Stauffer Chemical Company of Wyoming, a jointly owned subsidiary of Stauffer Chemical Company and Rocky Mountain Energy Company mines the trona and processes it into high-purity soda ash. Stauffer Wyoming has been in operation since 1962 with a current production capacity of approximately 2.2 million tonnes (2 million short tons) per year of soda ash. The Refinery has five parallel operating trains utilizing the monohydrate process which is a series of chemical processing unit operations described below. Screening and Crushing the Trona The mined trona is brought to the surface in two counterbalancing ore skips. The ore is initially screened with Refinery feed, less than peagravel size material, entering the process while the oversize is conveyed to an outdoor stockpile.

Jan 1, 1984

By Vinton A. Garbesi

INTRODUCTION The placing of the monolithic concrete lining of the Bi-County water tunnel illustrates the state of the art in the materials, equipment, methods and productivity available to the industry for this type of construction. This paper describes the management and engineering rationale used by Clevecon, Inc., a subsidiary of S & M Constructors, Inc., Solon, Ohio, in developing the concrete mix designs, the design of the specialized equipment, and the methods used in the manufacture, transport, and placing of the lining. Also discussed are the changes to the reinforcing steel design instigated to facilitate its handling and placing, as well as to enhance the quality of the lining. The intent is to bring to the attention of designers the effects certain design aspects have on the construction of reinforced concrete tunnel linings, as well as indicate the areas where research and development effort should be expended to further reduce costs for this type of construction. GENERAL DESCRIPTION The Bi-County Water Tunnel West is a water transmission main owned by the Washington Suburban Sanitary Commission of Hyattsville, Maryland. The facility was designed by A. A. Mathews Division (formerly STRAAM Engineers, Inc.) CRS Group Engineers Inc., Rockville, Maryland. It is to be utilized as the central feeder of potable water for the northern suburbs of Washington, DC, extending some 4,597 meters from a riser shaft at its western terminus to the eastern interface, with a similar tunnel which extends eastward about 5,180 meters; the majority of its length being under Interstate Highway 1-495. The excavated and finished diameters are 3.8 and 3.05 meters respectively. The reinforced concrete

Jan 1, 1981

By R. McCulloch

Exploration activity in metallic minerals continued to decline in Montana in 1992 as companies either reduced budgets or left the state. The number of active projects dropped another 50% from 1991. Expenditures were 3% to 6% of 1989's 28.6 million. Many of the major mining companies closed offices in Montana. Although depressed commodity prices have hurried the exodus, continuous changes in environmental regulations, as well as the Mining Law of 1872, without regard to economic effect have had the most serious impact. Many companies indicate that Third World countries present a more stable business environment than the United States. Grassroots projects are nearly non-existent, while late-stage programs continue cautiously. Exploration activity continued at the following projects: Garnet, Pegasus Gold; Southern Cross, Asarco; Elkhorn, Goldfields; 7-Up-Pete, Phelps Dodge and Canyon Resources; Miller Mountain, Pegasus Gold; Sheep Creek, Cominco American Resources; Checkerboard, Kennecott and BHP Utah International; Emigrant Creek, Pegasus Gold; and Crevise, American Copper and Nickel. All mineral activity, whether on private, state or federal land, is regulated by the Montana Department of State Lands under three classes of permits - Small Miner Exclusion Statements (SMES), Exploration Licenses and Operating Permits. A total of 230 Exploration Licenses are active in the state with 26 of those being new. However, there are only 433 projects current in Montana, with many of those in the reclaiming stage. The majority of exploration projects consist of individuals expending time rather than money on properties. The number of mines functioning under operating plans declined by one when W.R. Grace closed its Zonolite operation.

Jan 1, 1993

By R. B. Berg

Montana sapphires were first discovered in alluvial deposits in the Helena area in 1865 and subsequently were discovered in other alluvial deposits in southwestern Montana and also in a lamprophyre dike at Yogo in central Montana. From about 1900 until the late 1930?s, when synthetic sapphire began to come into widespread industrial use, Montana sapphire mines produced large quantities mainly for watch bearings with lesser production for the gemstone market. The Yogo deposit is now mined for the gemstone market and two of the alluvial deposits are mined to produce sapphires for the fee-sieving of sapphire-bearing gravel and for the direct sale of gemstones. The generally pale-colored sapphires from the alluvial deposits in southwestern Montana are heated to enhance their colors whereas the generally blue sapphires from the Yogo deposit require no treatment. Markets for sapphires from both the alluvial deposits and the Yogo deposit are strong. In spite of reported historic production in excess of 70 tonnes, mineable resources appear to remain at most major deposits. Also abundant untested lamprophyre dikes in central Montana may host sapphires similar to those at the Yogo deposit.

Jan 1, 2009

By Frank W. Pereira

The Montana Talc ore body was discovered in 1983 in Montana's Gravelly Range, about 40 km (25 miles) south of Ennis. Initial drilling indicated a 910-kt (1-million st) ore body of high purity talc. Preliminary analyses on ore cuttings included chemical analysis, brightness measurements, and microscopic evaluations of the structure of the talc. Results indicated it was similar to talc currently being marketed from Montana and it would probably have good commercial value. Based on the positive test results, a test pit was made and a 180-t (200-st) sample of ore was mined. A portion of the ore was ground to various particle sizes and evaluated to determine its strengths, weaknesses, and other characteristics. The deposit is located close to the Cyprus Yellowstone deposit. It was therefore believed that Montana Talc ore may possess many of the same characteristics. Testing and analyses showed the talc to have a high purity and an extremely large surface area, even for Montanatype tales. The ore was also situated in a massive deposit, indicating low cost mining. While the lab analyses were encouraging, the true evidence would be obtained from commercial tests in the marketplace. About 91 t (100 st) of ore were ground to product specifications for pitch control, paint filler, and plastics filler. Consumers were contacted and requested to evaluate the sample talc products. A major trial for the talc as a pitch control agent was arranged at a Northeast paper mill. The trial indicated the new Montana Talc product performed as well or better than the current standard in the industry. In fact, due to a minor modification in the compaction process to make the transport of the talc easier, the product had substantially less dust than the currently used product. The operating people at the paper mill requested that management purchase this talc. Trials were also run at paint plants for use as a pigment filler. And the talc was fabricated into a number of plastics compounds. The initial product tests were largely positive and provided encouragement to proceed with the project. Different grinding mills were used and their performance evaluated. Significant data were generated by the custom grinders. They indicated how the Montana Talc ore ground and the particle size distributions produced at different grinding settings. Encouraged by the positive marketing tests, a prefeasibility study was commissioned. A talc grinding plant and mine plans were designed and capital and operating costs estimated. Initial economics showed an attractive return. The operating costs were among the lowest in the industry. The positive economics, along with the excellent results by the products in the marketing tests to the paper, paint, and plastics industries, led to the recommendation to proceed with the project. Plant construction began in June of 1985. The Montana Talc Co. (MTC) analyzed the data from the commercial tests. Based on the product's outstanding performance and the uniqueness of its high purity and platy structure, a strategy was developed to position the company as a premium talc supplier.

Jan 1, 1989

By P. Knudsen, S. Rosenthal

INTRODUCTION In 2010, Montana Tech was gifted 65 acres of land immediately west of the campus. The parcel of land included an old silver mine called the Orphan Boy Mine. The Orphan Boy and its sister, Orphan Girl, were developed about1895 and operated until 1956. In addition to the gift of land, a significant industry gift was obtained to develop a first class training facility, which we call the Underground Mine Education Center (UMEC). The UMEC has been funded primarily by industry through donations of dollars, equipment, and supplies. The UMEC is a unique hands-on, educational environment for today’s students who are being trained to find, develop and process the worlds' natural resources. The center complements courses in mining engineering, geological engineering, environmental engineering, metallurgical engineering and occupational safety and health. It also serves as a as research facility utilized by students and faculty, and other organizations interested in doing research a hard rock underground mine. LOCATION The Orphan Boy and Orphan Girl Mine are located approximately 700 feet (ft.) apart and the Orphan Girl Mine is part of the World Museum of Mining. Underground they are connected on various levels and all levels below the 100 ft. level are currently flooded. The Orphan Boy mine was 804 ft. deep and Orphan Girl was 3200 ft. deep. The surface locations of the two mines and some of the underground workings on the 100 ft. level are shown on Figure 1 (2015). CONSTRUCTION Land ownership was gifted from BP/ARCO in 2010 and planning started immediately. In June of 2011, site development for the decline to the 100 ft. Level of the Orphan Boy began with a satisfactory portal site developed (Figure 2). We hoped to be able to start driving the decline in July. However, the portal was sited approximately 125 ft. away from a natural gas line that bisected the Montana Tech campus. While outside the right of way for the line, Northwestern Energy requested that no blasting be performed near the gas line until such time as the gas line was abandoned in the fall so decline development was put on hold. The gas line was officially abandoned in January of 2012.

Jan 1, 2019

By Daniel J. Turk, William R. Banning, John Paterson, Thomas J. Weitz, Michael L. Clark

Introduction Pegasus Gold's Montana Tunnels mine is a large surface gold, silver, lead, and zinc mine located 37 km (23 miles) south of Helena in southwestern Montana. Milling operations commenced in late March 1987. The concentrator achieved full production in May that year after undergo¬ing several modifications and improvements. Production for 1988 is projected to be 2.48 t ,80,000 oz) of gold, 34.2 t (1.1 million oz) of silver, along with 8.5 kt (9400 st) of lead, and 22.6 kt (25,000 st) of zinc from lead and zinc concentrates. Mill throughput currently averages 11.7 kt/d (12,900 stpd), compared to the origi¬nally designed capacity of 11.3 kt/d (12,500 stpd). Cash production costs, net of bypro¬duct revenues for the third quarter 1988, were below $3.20/g ($100 per oz). The introduction of ore to the concen¬trator marked the culmination of 12 years ex¬ploration, evaluation, and development. Initial milling operations encountered diffi¬culties with the circuit as designed. As a result, several modifications and improve¬ments were made to the plant. This article is intended to assist other companies developing projects of this type and complexity. It discusses the mine's de¬velopment from feasibility and construction through start-up. The operation, as it exists today, is reviewed including the modifica¬tions and improvements made since start-up. History The mine is situated in Jefferson County, MT within the historic Corbin-Wickes min¬ing district. Underground mining began in 1864 and flourished until the early 1900s. Between 1864 and 1900 the vein deposits in the district produced about $41 million dol¬lars worth of lead and silver ores containing subordinate amounts of zinc, copper, and gold. At various times, three smelters were operated in the area.

Jan 1, 1989

By K. Verghese

Neutron capture prompt gamma-ray analysis provides the best method for on-line analysis of the elemental composition of large volumes of bulk material. This paper summarizes the Monte Carlo models which simulate the radiation transport within two such analyzer systems; namely, the borehole configuration and the conveyor belt configuration. The models are useful in the design optimization of the analyzer systems, in minimizing the amount of experimental calibration data for calibrating these analyzers, and in investigating the detection sensitivity for different elements. The computational scheme in these models is made extremely efficient by the use of various powerful variance reduction methods and by efficient data management. Experimental verifications of the two models carried out in the laboratory indicate very good agreement with the Monte Carlo results.

Jan 1, 1984

By B. A. Ridolfi, S. M. Alvarez

The Moon Creek Reclamation Project provides a case study in the development of creative cleanup solutions for an abandoned lead and zinc mine and mill site located in northern Idaho. Innovative design features include construction of a 88,000cubic yard combined waste containment facility on soft in-situ tailings, water-balance cap, limestone gravel drains, a geocell mattress for stability, and a below-grade scour protection berm. The stream, including a wetlands buffer, will be relocated within an existing road alignment and rehabilitated to provide trout habitat. These elements allow for the integration of reclamation and stabilization measures into an effective site design.

Jan 1, 1999

By S. M. Alvarez

The Moon Creek Reclamation Project provides a case study in the development of creative cleanup solutions for an abandoned lead and zinc mine and mill site located in northern Idaho. Innovative design features include construction of a 88,000 cubic yard combined waste containment facility on soft in-situ tailings, water-balance cap, limestone gravel drains, a geocell mattress for stability, and a below-grade scour protection berm. The stream, including a wetlands buffer, will be relocated within an existing road alignment and rehabilitated to provide trout habitat. These elements allow for the integration of reclamation and stabilization measures into an effective site design.

Jan 1, 1999

By Edmond O’Donovan

Mooranbah North is a new greenfield project in Australia's Bowen Basin that is projected to produce 4 mtpa of hard coking coal from a single longwall. Located in Central Queensland in Australia's northeast, this is one of Australia's main coal producing regions. From the outset, Mooranbah North's approach to equipment selection has differed markedly from that usually taken in the mining industry, and the conveyor industry in particular. Until recently, no performance requirements have been placed on conveyor equipment suppliers. This arose from a practice of purchasing components in an ad-hoc manner from a variety of sources, and the mine then configuring the system. More recently, single source supply has been adopted as a means of obtaining some performance guarantee, usually expressed in terms of system availability. Unfortunately, the term "availability" has a multitude of definitions, particularly in the underground coal sector. A conveyor availability of 98% is a common goal but this rarely means the conveyor must operate 165 hours/week, 52 weeks/year. There are mines that have one maintenance shift for each production shift and claim availability of 100%. What is meant is that no down time is logged to the conveyor during the hours that it is wanted. This "generous" definition of availability would not be tolerated in many industries and nor should it. Unfortunately, a true definition of availability, such as is applied to steam turbines in the power generation industry, is not particularly helpful. Five day/ week operations would immediately face a 28% penalty against 7 day rosters, and there would be no sensible manner in which weekend maintenance could be incorporated into the availability formula. The approach adopted by Mooranbah North was to specify a period of "Failure Free Operation," which would be followed by a maintenance period. This

Jan 1, 1998

By Fred C. Bond

Any improvement in the accuracy of commercial comminution calculations under the Third Theory must be accomplished either by increased precision in energy input measurements, or by a better evaluation of the total new crack length produced, as indicated by the feed and product size distributions. Since at the present time feed and product sizes are approximated solely by the microns 80% passes, the most promising opportunity for increased accuracy lies in consideration of their plotted size distribution characteristics. This paper shows how more accuracy can be obtained over an increased range of feed and product sizes from size distribution studies.

Jan 1, 1962

By J. Harrison Daniel

More stringent dust standards, because of quartz in coal, have become a major compliance problem for the coal industry. Reducing quartz levels has become the major focus of the Bureau of Mines dust control research program. Results to date have identified hath the sources of quartz and prospective control technology. Control techniques are being developed for both room-and-pillar and longwall mining underground operations. Techniques include changes in face ventilation, mining cycle modifications, and better roof bolting dust control.

Jan 1, 1985

By Georgene Renner, William R. Yernberg, Steve Kral

Allmand exhibited its LSC 100Light Sequence Commander, the mining industry’s first automatic lighting and command control system. The system is available with all of Allmand’s portable light towers. The LSC100 uses a preset photocell sensor that allows the light tower to be automatically turned on or off. At dusk, the sensor engages the power unit and then activates the light. At dawn, the sensor automatically shuts off the light. The unit also features an eight-event digital timer that allows eight separate sequences daily. The LSC100’s sequenced light control ensures that the engine is started before the lights are turned on or off. This prevents possible generator damage that can occur if the unit is powered down under load. Also, a low-fuel shutdown sequence helps protect the generator from damage by automatically shutting down the unit when the fuel level reaches 10 percent. And the LSC100’s smart circuitry senses engine water temperature during startup, determines the glow-plug time requirement and schedules repeat intervals, if necessary, to start the diesel engine.

Jan 1, 2004