Search Documents

By Robert Blair, David L. Fey, Stanley E. Church

Determination of the pre-mining geochemical baseline in bed sediments in watersheds impacted by historical mining activity is important in establishing watershed restoration goals. We have developed methods to solve this problem in the Animas River watershed, southwestern Colorado, using geomorphologic mapping to identify terraces that contain pre-mining sediments. Following a systematic evaluation of possible sites, we collected samples of pre-mining sediments in gravel deposits from 21 sites throughout the watershed. Geochemical analysis of individual layers has produced a chemical stratigraphy that can be tied to the historical record through geochronological and dendochronological studies. Analysis of geochemical data, when coupled with the historical record, clearly shows that there has been a major impact on the geochemistry in bed sediments in the active stream channel by past mining activities. Historical mining has resulted in a substantial increase in metals in the very fine sand to clay-sized component of the bed sediment of the upper Animas River, and Cement and Mineral Creeks, which are the major tributaries of the Animas River. Enrichment factors for metals in modem bed sediments, relative to the pre-mining sediments, range from 1 to 6 for arsenic, 1 to more than 10 for cadmium, 1 to about 15 for copper, 1 to more than 25 for lead, 1 to more than 10 for silver, and 1.6 to more than 12 for zinc. The pre-mining bed sediment geochemical baseline is high relative to average crustal abundance values of many metals. The Animas River watershed above Silverton, Colorado would be readily identified as a highly mineralized area suitable for mineral exploration if it were not disturbed by mining.

Jan 1, 2000

By R. V. Ramani

Minerals, together with agricultural and forestry products, are the primary source of wealth produced in the United States. Although the production of minerals requires only a small fraction of the state's total land surface, as compared with either agriculture or forestry (Table 1), mining activities generally are much more disruptive to the land surface, and rehabilitation is more complex and costly. The past 10 to 15 years have witnessed a sharp increase in mineral exploration and mining, particularly coal mining, which has brought with it an increase in conflict over land use and an increase in negotiations for purposes of mineral prospecting and mining. The general increase in the production and consumption of coal and the particular increase in the percentage of coal extracted by surface mining methods coupled with a growing nationwide environmental consciousness have created increased public concern and in some cases outrage over mining activities. Although there is ample evidence to indicate that it is possible to plan for and design mining activities in such a way that they are compatible with other activities and can thus be made a part of a sequential land-use plan, there is a general lack of knowledge regarding the importance of mining as the provider of basic and essential raw materials to supply society's constantly expanding and increasing mineral needs. This lack of knowledge extends to such matters as land and mineral rights negotiations, the character of mineral deposits and minerals, mineral economics, and land-use planning.

Jan 1, 1977

By Carl R. Christiansen

Underground sites have great potential for industrial plants, for warehouses, and for other purposes where above-surface locations are now employed. Subsurface locations have generally been over- looked by industrial planners even though they may offer many features of superiority over the conventional sites. There are many opportunities for industries or warehouses to go underground. New space can be excavated expressly for this purpose or openings in existing mines may be converted to useful space. Another possibility is the pre-planned mine-industrial site, in which a mineral product is mined and marketed as a commercial venture while utilizing a mining plan which will permit rapid conversion of the openings created into active industrial areas while mining continues in the adjacent ground. An underground plant located in chambers created by excavating space in solid rock has many advantages, including low construction costs, low heating-cooling costs, freedom from storm damage or other surface weather conditions, absence of traffic noise and vibration, fireproof construction, low insurance costs, excellent working conditions, easily controlled temperature and humidity, almost unlimited bearing capacity of floors, low maintenance costs, no effect upon surface.

Jan 1, 1973

By Adrian J. Mathias

For many years excavations were made in rock exclusively by conventional blasting methods, and without concern for damage to the rock surfaces which remained after the excavation was completed. Recently, however, there is an increasing awareness for the importance of making rock excavations with as little damage as possible to the remaining rock surfaces; consequently, several revolutionary new precision blasting techniques have been developed during the past few years. These techniques, variously known as cushion, smooth- wall, perimeter, pre-shear, and pre-split blasting, basically involve the creation of a fracture plane in the rock between a series of blasted holes. The variations in each of these techniques are largely due to the differences in hole diameters, hole spacings, methods of charging, and sequence of blasting used to achieve certain specific results. The development of these precision blasting techniques was initiated by Canadian Industries Limited in 1953 at the time the Sir Adam Beck No. 2 Hydro-electric Project was under construction by the Hydro-Electric Power Commission of Ontario. Since then, these techniques have been somewhat advanced, and they have been applied with varying degrees of success to a number of projects. These projects include railroad and high- way cuts, dam spillway channel excavations, canal excavations, tunnel driving, shaft sinking, and other underground applications.

Jan 1, 1965

By Calvin J. Konya

An investigation was performed to determine conditions which optimize fracture formation between blastholes used for purposes of pre-splitting. Experiments-involved high-speed photography in Plexiglas models and radiographs in sandstone models. Additionail data was obtained from full-scale pre-split blasts. Pre-split fractures between blastholes were found to form as a result of gas pressure and were affected little, if any, by stress wave interactions. Pre-splitting was effective with short period delays of 25 milliseconds or less, and did not require instantaneous initiation of blastholes. Significant reduction of ground vibration resulted with the use of delays

Jan 1, 1980

By Vojtech Gall

Pre-support measures for urban tunneling have seen a substantial development in the recent past. Ground improvement techniques, pipe-arch and spiling methods now allow for non-disruptive tunneling at very shallow depths under sensitive structures, rail tracks and roadways. The paper presents experience gained on national and international projects built over the past decade that represent case histories and therefore may be used as guidance for the development of similar solutions for future tunneling projects at shallow depths. Reference projects include tunnels for the Washington, DC Metro, London Underground, Dulles Inter-national Airport, Busway tunnels in Boston and the Ft. Canning Tunnel in Singapore.

Jan 1, 2008

By V. Adamek

The specific lithological conditions over the Pittsburgh coalbed, highly resistive limestone and sandstone units with relatively shallow overburden, prevent the use of any predictive method as developed for European conditions. This paper describes the development of a subsidence precalculation methodology suitable to the mining-geological conditions in the Northern Appalachian Coal Field. It has been found that due to lithological conditions over the Pittsburgh coalbed the subsidence coefficient varies within the area of the subsidence trough. This is different from the European conditions where the subsidence coefficient is considered to be a constant. The effects of lithology, in-the form of a variable subsidence coefficient, have been separated for each test site by introducing a correlation between hypothetically homogeneous overburden and existing lithological conditions, while providing for different mining conditions. Field data from eleven Bureau longwall panel studies were used in the regression analysis. For each panel the characteristics of the variability of the subsidence coefficient along individual profile lines were defined. Regression analysis of the subsidence coefficients from all test sites on the location relative to the edge of the panel has yielded a third degree polynomial equation with a coefficient of correlation of 0.9999. All sensitivity tests have shown good results.

Jan 1, 1985

By Kent C. Condie

Precambrian terranes in the Rocky Mountain region decrease progressively in age from the Archean Wyoming Province (> 2.5 b.y.) to the late Proterozoic in West Texas (figs. 1,2). Within the Wyoming Province, most dates fall near 2.7 b.y. although some are recorded at 2 3.8, 2.9, and 2.6 b.y. Although Penokean (- 1.8 b.y.) deformation and plutonism are recorded in southeastern Wyoming, most Precambrian rocks south of the Wyoming shear zone, which separates the Archean and Proterozoic provinces, are < 1.76 b. years in age. Supracrustal rocks in Colorado, western Arizona, and northern New Mexico fall in the range of 1.72-1.76 b.y., those in central New Mexico about 1.65 b.y., those in southeastern Arizona and southwestern New Mexico about 1.70 b.y., and those in West Texas 1.1-1.2 b.y. The Wyoming Province is comprised chiefly of 2.7 or 2.9 b.y. tonalitic gneiss terranes intruded by 2.6 b.y. granites in the central and southern parts of the province. Supracrustal rocks are minor and include greenstone belts comprised chiefly of pillow- ed tholeiites and graywackes and remnants of quartzite-shale successions. Metamorphic grade in greenstone-gneiss terranes ranges from upper greenschist to amphibolite facies and in quartzite-gneiss terranes from upper amphibolite to granulite facies.

Jan 1, 2013

By James W. Stewart, A. C. Colvine

Introduction Precambrian shield terrains the world over are experiencing an unprecedented level of concerted exploration for lode gold deposits. Reasons for this include: • The increase in the price of gold (following 40 years at $1.13/g or $35 per oz) has transformed targets that were once unattractive into viable exploration propositions. • The relatively suppressed market for other metals produced from shields (base metals, nickel, iron, and uranium) has further focused exploration attention on gold. • The preeminence of gold production from rocks of early Precambrian age, as shown in Fig. 1. • The relatively high grade of gold in these mines (averaging about 10 Wt or 0.29 oz per st) permits profitable extraction even under depressed gold prices. A number of these mines have been in continuous operation for more than 50 years. • The recent discovery of the major Hemlo deposit, in well exposed rocks adjacent to the Trans Canada Highway, has had a world-wide impact. This demonstrates that a major new deposit can be found even in an accessible, well exposed area of a shield; gold mineralization is susceptible to rational exploration; and new target types for gold exploration exist. This paper reviews exploration activity for gold in shield terrains worldwide (Fig. 2), excluding Early Proterozoic paleoplacers of the Witwatersrand type. Emphasis is on the Archean, which is traditionally the most productive part of the Precambrian shields. There is also an emphasis on the Canadian shield (Fig. 3) because of its vast areal extent and exceptionally broad range of mineralization styles. Geological Approach A basic problem exists in gold exploration when compared to exploration for base metal massive sulfides that predominated during the 1960s and 1970s. Gold concentrations cannot usually be detected by airborne geophysical instruments. The majority of massive sulfide deposits were detected using airborne electromagnetic detectors and magnetometers. A full 75% of Canadian gold discoveries can be credited to surface prospecting. The percentage is even higher in other countries. This observation allows for great optimism for two reasons: • Large areas of shield terrain are obscured by either surficial deposits (glacial tills, clays, and desert sands) or deep surface weathering. This makes them inaccessible to prospectors. Logic dictates that such obscured areas should have the same potential for gold concentration as has exposed bedrock. • The Hemlo style of mineralization, a roughly tabular ore body where gold is associated with disseminated sulfides, is different from the traditional prospecting target. The gold is hosted by discrete quartz veins. While it is true that limited discoveries were made at Hemlo more than 30 years ago, and this style of mineralization is present elsewhere, recent

Jan 12, 1984

By William R. Groseclose, Kenneth D. Schoeman

The Buckskin Mountains Tunnel is a key link in the Bureau of Reclamation&apos;s Central Arizona Project. The 22-foot (6.7-m) diameter tunnel is being bored in a north-northwesterly direction through volcanic rock near Lake Havasu in western Arizona. The 6.9-mile (11-km) conveyance tunnel will carry up to 3,000 cfs (85 cu m per sec) of water through the Buckskin Mountains as part of the Granite Reef Aqueduct. The water for the project will be drawn from Lake Havasu behind Parker Dam on the Colorado River and pumped some 800 feet (244 m) above the lake to the inlet portal of the free flow tunnel where it begins its 190-mile (300-km) journey to Phoenix, Arizona, and beyond into Orme Reservoir (figure 1). Precast concrete segments are being used as a single system initial support and final lining in the tunnel being excavated by a tunnel boring machine specially designed and built for the job by The Robbins Company. J. F. Shea Company, Inc., of Walnut, California, is constructing the tunnel for the Bureau of Reclamation.

Jan 1, 1976

By Henry R. Tiedemann, William H. Hansmire, Harvey W. Parker

Although the use of precast concrete segments for tunnel linings has been common for many years in Europe, acceptance of this type of lining has been slow in the United States. This paper explores the cost, design, and construction considerations of concrete segmental lining with a view to promoting its use in this country when favorable conditions exist. The different perspectives held by owners, designers, and contractors are discussed. In addition to cost, other considerations include previous design and construction experience, size, length and function of tunnel, watertightness, and liability. Cost comparisons are made to traditional ground support and lining. Under favorable conditions, the use of precast concrete segmental linings can be technically feasible and cost effective.

Jan 1, 1987

By Arthur P. Chase

The Tacubaya subway tunnels form a link in the Sistema de Transporte Colectivo (Mass Transit System) of the Federal District of Mexico. One tunnel 327 m long lies to the north of Tacubaya Station, the other 811 m long, to the south. The tunnels are designed to accommodate two subway trains, one inbound and one outbound, within the inside diameter of 8.5 m. The designers of the tunnel lining and tunnel driving equipment were faced with the problem of driving two subway tunnels 9.0 m outside diameter through water-bearing soil, directly beneath a high speed limited access highway, a main drainage sewer, structures including residences and office buildings, on an alignment curved for 67 per cent of tunnel length, and on grades as high as 7 per cent, within a limited budget, with minimum damage to property and disruption to the community. Planning The following decisions affecting tunnel design and construction were made at an early stage of planning: Shield. To enhance safety, a tunnel shield would be used for tunnel driving. Dewatering. The water-bearing soil could be effectively dewatered; consequently, tunnel driving could be performed in free air. Hand Mining. To minimize investment in equipment, hand mining would be used to excavate and support the face.

Jan 1, 1997

By Carlos Viramontes Aldana

Mining in Mexico is one of its post traditional activities, whose influence in the development of important cities and communications has been decisive. Precious metals and, to some extent, copper and tin were known and used before the Colonial period, but from the sixteenth century to tie end of the nineteenth century, mining and metallurgical industries were concentrated in the precious metals, mainly silver. This silver was exported to Spain and other countries under the Spanish. Rule, Mexican peso was known world wide since the end of the sixteenth century and Mexico ranked as the first silver producer since the eighteenth century.

Jan 1, 1985

By R. Flores V.

The Refugio Project is located in the Andes mountains of northern Chile, in the Maricunga Hineral Belt. The Verde, Pancho and Guanaco Au ore bodies have been recognized and are Early Miocene in age. Mineralization consists of fine-grained disseminated gold hosted by dacitic to dioritic subvolcanic porphyries. Alteration comprises massive to veinlet-controlled silicification overprinted on earlier potassic and propylitic alteration and surrounded by later argillic alteration. Geologic relationships suggest that the Refugio ore bodies occur within an Early Tertiary volcano overlying Paleozoic and Mesozoic basement rocks. Geologic reserves at Refugio are approximately 300 million grams (9.7 million ounces) of gold. The Verde deposit contains 185 million tonnes of mineable and leachable ore with an average grade of 0.90 glt Au and is currently in the pre-construction stage after a positive feasibility study. Proven and probable mining reserves at Verde deposit are 101 million tonnes at an average grade of 1.02 glt gold. Additional potential exists at to other deposits within the Refugio property (Pancho and Guanaco) but no reserves have yet been defined due to the limited drilling to date.

Jan 1, 1994

By Felix E. Mutschler

Alkaline rock-related precious metal deposits include: • orthomagmatic platinum group elements (PGE) ± gold (Au); • porphyry copper-silver-gold (Cu-Ag-Au, ±PGE); • epithermal Au-only, and Au-Ag-base metals; • submarine exhalative Kuroko-, Cyprus-, seamount- and Yellowjacket-type deposits; and • enigmatic deposits akin to Olympic Dam. Coeval epithermal deposits related to porphyry deposits suggest the two types represent separate immiscible fluids evolved in oxidized, CO2-rich alkaline magma chambers. Alkaline rock provinces develop above mantle hot-spots, but crustal structures control the final distribution of magmas and ore fluids. Prospecting guides for alkaline rock-related precious metal deposits include the presence of evolved alkaline rocks, pervasive K-metasomatic, redox and carbonatic alteration and low level Au (±Te, etc.) anomalies. Although alkaline igneous rocks crop out in less than 1 % of the area of the North American Cordillera and craton, alkaline rock-related ore deposits have produced nearly 13% of the total United States and Canadian lode gold production. Large (31-t or 1 million-oz) deposits are common (Fig. 1), and additional deposits and reserves are being discovered. New genetic models are evolving, making alkaline rock-related precious metal prospects attractive exploration targets.

Jan 1, 1991

By Steve Scherrer

power point slides

Jan 1, 2000

By G. Bee, Z. Gavelan, R. Espinel, Y. Roditis, X. Ochoa

In August 1996 Barrick Gold Corporation acquired the Pierina property, an advanced stage exploration project, high in the Andean Cordillera of Peru and in November 1998, in a record time of just over two years, poured the first gold. After more than three years of a very successful operation at some of the lowest operating costs in the world, this presentation serves to briefly describe the project through design, construction and start-up and in particular to spotlight some of the challenges that have been overcome in valley heap leaching in a high rainfall, alpine setting.

Jan 1, 2002

By R. D. Beard

Puerto Rico lies within the remnants of a deformed Cretaceous island arc system in the northeastern Caribbean. The Island can be divided into three broad geologic provinces: the Central Volcanic-Plutonic Province (Lower Cretaceous to middle Eocene), and the Northern and Southern Limestone Provinces (early Oligocene to middle Miocene). Known precious metal deposits are generally small and occur in veins and shear zones within Lower and Upper Cretaceous volcanic and plutonic rocks. Some Tertiary igneous rocks are also mineralized. Selected indications of disseminated lithology-controlled mineralization could represent larger deposits. Associated metals in some deposits include copper, zinc, and lead. At present, tax policies, population density, political outlook, and lack of proven significant precious metal deposits discourage the establishment of a metal mining industry.

Jan 1, 1993

By G. Myers, C. J. Wendt, W. H. Wilkinson, M. D. Dennis

Precious metal mineralization at Mt. Hamilton, NV is associated with a polymetallic, garnet-pyroxene skarn system developed in middle to upper Cambrian calcareous shale, limestone, and dolomite. The skarn is developed around the Cretaceous Seligman and Monte Cristo calc-alkaline stocks. Gold is associated with intense retrograde alteration. Later epithermal quartz veins contain gold, silver, base-metal sulfides, and sulfosalts cross-cut skarn alteration. Westmont Mining Inc. is currently developing two mineralized zones containing a geologic resource of about 7 Mt (7.7 million st) that averages 1.7 g/t (0.05 oz per st) gold and 17.2 g/t (0.5 oz per st) silver. The project will have an estimated mine life of seven years, with a planned annual production rate of I t (35,000 oz) of gold and 9.3 t (300,000 oz) of silver.

Jan 1, 1990

By M. D. Dennis

Precious metal mineralization at Mt. Hamilton" Nevada is associated with a poly-metallic, garnet-pyroxene skarn system developed in middle to upper Cambrian calcareous shales, limestones and dolomites. The skarn is developed around the Cretaceous Seligman and Monte cristo calc-alkaline stocks. Gold is associated with intense retrograde alteration. Later epithermal quartz veins containing gold, silver, base-metal sulfides, and sulfosalts cross-cut skarn alteration. Westmont Mining Inc. is currently developing two mineralized zones containing a geologic resource of approximately 7.7 M.T., which averages 0.05 OPT gold and 0.5 OPT silver. The project will have an estimated mine life of seven years, with a planned annual production rate of 35,000 ounces of gold and 300,000 ounces of silver.

Jan 1, 1989