Search Documents

By Chee Theng

"So many talks, so little time.One of the toughest challenges associated with attending the SME Annual Conference and Expo is deciding how to allocate one’s resources. After accounting for keynote and plenary sessions, committee meetings, networking events, luncheons and exhibits, attending even one of the 109 technical sessions and more than 600 technical paper presentations can be a labor of love. Many, however, managed to make it to many of the sessions, including the mineral and metallurgical processing technical session on solvent extraction, ion exchange and electrowinning.At one point, that room was seated to near capacity, with a considerable number of the audience members standing by the walls at the back. Brittany Valera of Freeport-McMoRan Inc. was one who came early and enjoyed the session in its entirety. "Everything was pretty exciting," she said. "I really liked the modular plants. I think the future of mining, just like what we talked about in there, lies in thinking about things like remote locations, lifetimes of plants, anything that would be reusable and sustainable; and lower-cost and user-friendly would be really beneficial."Michael Moats, associate professor of metallurgical engineering at Missouri University of Science and Technology, started off the session by presenting on behalf of post-doctoral student Alex Luyima, who, like many before him, had been snapped up by industry and is now working for a secondary-metals refining company in Texas. Their team studied the nucleation and growth mechanism of copper on stainless steel from synthetic acidified copper sulfate in the absence and presence of chloride ions and three commercial organic additives: Hydrostar 4208, DXG-F7 and Cyquest N-900. Currenttime data were analyzed using known models, with reference to scanning electron microscope images. Good agreement was achieved between the models and SEM micrographs of deposits at a commercially relevant current density of 30 mA/ cm2. The addition of 20 mg/L chloride was found to increase the size and reduce the number of nuclei. The addition of 2.5 mg/L of each additive did not change the mechanism, but all three reduced the size and increased the number of nuclei, leading to more uniform coverage of the substrate with smoother deposits produced in twohour electrowinning experiments. N-900 had the best deposition coverage while DXG-7 was the easiest to dissolve."

Jan 1, 2014

By William Gleason

"During the past nine years the number of cellular phones connected to a network has increased from 34 percent of the world’s population in 2005 to 93 percent in 2014. These phones are powered by a combination of materials including elements such as gold, silver, copper and rare earths. And, as more parts of the world become connected to networks, the number of phones being produced, and the elements they will need, will continue to increase. The demand comes as prices for these commodities are slumping and access to the commodities is getting more difficult, technically and socially.These mobile devices have connected people around the world in ways that could not have been imagined two decades before, and, ironically, this communication has strengthened opposition to the development of the mines that produce the very materials they need to operate.In his keynote address to the 2014 SME Arizona Conference at the JW Starr Pass Resort in Tucson, AZ, on Dec. 8, 2014, John O. Marsden, SME President and president of Metallurgium, spoke to more than 500 attendees about the challenge to produce the materials that society needs while at the same time challenging the general public’s perception of mining that is often inaccurate and less than favorable.Marsden highlighted the amount of raw materials that will be needed not just for phones, but also for things such as automobiles, including electric cars, as a way to illustrate the importance of mining. Even so-called green products such as Tesla cars, which require about 317 kg (700 lbs) of aluminum, 13 kg (30 lbs) of copper and 36 kg (80 lbs) of cobalt for their eco-friendly batteries, will need materials mining provides.These are some of the numbers that the general public is often unaware of. They are part of the necessary things that mining provides for society but are rarely reported on. Instead, it is the accidents like the tailings spill at the Mount Polley Mine in British Columbia and at the Buena Vista Mine (Sonora, Mexico) that grab headlines and stick in the minds of the public, adding more challenges to an industry that already has its own complex technical challenges to deal with."

Jan 1, 2014

By P. I. James, M. R. Baker

This paper examines new copper production from waste-grade ore using Blue Planet Strategies’ DEMET™ (Dynamic Electrode Mining Effluent Treatment) technology, which aims to bridge the practical weak pregnant leach solution (PLS) processing gap in heap leach-solvent extraction/electrowinning (SX/EW) operations by electrochemically removing metals from weak streams and generating product streams strengthened in target metals in a functional analog to SX. Weak PLS treatment was studied and used to estimate the economic and production impacts for a representative hypothetical brownfield copper heap leaching and DEMET-augmented SX/ EW operation to utilize "waste ore." Copper removal at 86% plating efficiency to below 0.1 g/L copper with power consumption of 0.55 kWh/lb copper and product strengths of over 10 g/L copper are presented. Modeling yielded approximately $2/lb total copper production and = $1/lb treatment costs with an immediate operation gross margin increase of 12% for the augmented brownfield. Potential mine life extension with an average 38% gross margin on "waste ore" augmented production at copper values of $3.25/lb was also indicated.

Jan 1, 2014

By Feng Junfa, Du Feng, Li Huamin, Syd S. Peng

"The Ordos coal field is located in the northern midwestern part of China (Fig. 1). Since the mid- 1980s, it has been developed into one of the major coal fields in the world, producing approximately 833 Mt (918 million st) of raw coal in 2013. There were once more than 400 coal mines operating in the region. However, due to the combination of market conditions and implementation of government consolidation policies, the number of coal mines operating in recent years has been reduced considerably, with increasing output.The surface of the Ordos coal field is covered with loess and alluvium layers of varying thicknesses. In many areas, their combined thickness may amount to as much as 100 m (328 ft) underlain by thin bedrock. Many loess and alluvium are aquifers receiving water from rainfalls. There are also gullies of varying depths crossing the coal field. Figure 2 is a typical stratigraphic column highlighting the coal seams and roof and floor rocks of interest.In conjunction with the development of highproductivity coal mines, numerous ground control instrumentation tests have been conducted in the operating longwall panels. Analyses of the results of those tests offer the opportunity to understand the effect of wide-ranging mining and geological factors on the overburden movement. For this reason, trips were made to coal mines of interest to interview mine management and collect their unpublished internal research reports on ground control instrumentation. In addition, literature searches on published thesis/dissertations and papers in the professional journals were performed. Finally, data from a total of 95 fully mechanized longwall panels were collected. The instrumentation involved primarily the monitoring of hydraulic pressures of longwall shields, from which the first roof weighting and first roof caving interval and periodic roof weighting and periodic roof weighting interval were identified and determined. Some panels also included measurements of roofto- floor convergence at the face, roof strata bed separation, longwall face sloughage and the height of caving and fractured zones in the overburden. Those 95 panels were located in 20 coal mines (Fig. 1) congregated along both sides of the Wulunmulun River with the following mining and geological conditions. All together those 20 mines produced more than 224 Mt (246 million st) in 2013, accounting for approximately 27 percent of the total coal production in the Ordos coal field:1. Period of mining: 1991-2013.2. Mining methods: All panels employed the one slice, full-seam natural-caving longwall mining method like those practiced in the United States. All panels were developed with a twoentry system with a single-row of chain pillars measuring 20- x 20-m (65.6- x 98.4-ft) wide.3. Coal seams (Fig. 3): Coal in Ordos coal field is high-quality steam coal, that is very low in sulfur, potassium and ash, but high in Btu. Data were collected in panels mined in a total of 10 seams with 82 panels in four seams and the remaining 13 panels in six seams. The first six seams (1-2, 2-2, 3-1, 3-2, 4-2, 5-2) were mined by the Shenhua Coal Group (the world’s largest coal company) and the #4-2, 5-2, 6R, 62, and 62R seams were mined by both the Shenhua and Yitai Coal groups. In each coal group, the sequence of mining was in descending order. For example, in Shenhua Group, the top seam 1-2 was mined first, followed by the 2-2, 3-1, 3-2, and 4-2 seam in that descending order. In Fig. 3, the top-down sequence of coal seams is listed from left to right in each coal mine group. All seams were near horizontal with dip angles less than 3°."

Jan 1, 2014

By John J. Sammarco

"The mining industry has made great strides in making mining safer and reducing the occurrence of mine disasters. Nevertheless, sometimes miners encounter smoke while trying to escape from a mine. Underground miners use different visual cues to help them escape from a smoke-filled environment. Foremost, miners look for primary and secondary escapeways that are typically indicated with reflective markers of various colors, with at least 11 colors available from manufacturers. Federal regulations require that escapeways be marked, but they do not specify the colors to be used. Thus, no standard color code exists and some colors can be more difficult to see in a smoke-filled mine.Researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) tackled this problem by taking a human-centered approach to provide miners with better visual information that would improve their ability to see escapeway markers in smoke, thus enhancing their ability to self-escape. What marker colors does your mine use?Does your mine use blue retro-reflective markers to indicate primary or secondary escapeways? Is your mine ready to purchase new or replacement retro-reflective markers? Color is important and blue had the poorest visibility as determined by OMSHR’s recent research investigating the visibility of markers in smoke. OMSHR researchers are not alone in their interest to improve a miner’s ability to escape - specifically when their efforts are hampered by smoke. For instance, there is a LinkedIn Mining Safety subgroup called "Standardized Color Code for Escape Ways and Returns in Underground Mines," and a recent National Academy of Sciences report recommended the development of humancentered technologies to enhance self-escape from underground mines. The mining industry has a common goal of helping improve miner safety, especially when it can be done by way of a simple and relatively low-cost solution of using escapeway colors that are more visible."

Jan 1, 2014

By Michael Roach

"There’s a bit of confusion and misinformation in the tunneling and underground construction industry regarding contractor joint ventures. If it was all so clear I would not have been "asked" to write this article. For those of us on the contractors’ side of the fence, joint venture business relationships have been a part of life for a long time. But even for contractors, there can be a bit of confusion, and it normally begins on bid day.How often have you received bid results and wondered (out loud, usually), "Who the hell are the Lake Mead Intake Constructors"? or the "Regional Connector Constructors"? Once you get past the name, you see that there is nothing behind Oz’s curtain other than a couple of contractors bidding and building work in an attempt to make a profit. So take a few minutes to read the rest of this, and I’ll do my best to dispel a few mythWhat is a joint venture?In some form or fashion, joint ventures are as old as industry itself. In the United States, some of the earliest (and largest) joint ventures involved the railroads and oil companies in the late 1800s. In the United States’ underground construction industry, joint venture names such as, Healy-Greenfield, Green and Winston, Gates & Fox and Walsh, Shea-Ball, Kenny-Paschen and S&M-Traylor bring back memories of successful joint ventures that operated over many projects.There are nearly as many definitions for joint ventures (JVs) as there are attorneys. A short and simple definition is, "an association of two or more companies engaged in a singular, for-profit business enterprise without actual partnership or incorporation." That’s it. Two or more contractors decide to partner up for one or more projects. One benefit of the JV relationship is that the partners typically do not need to file incorporation documents, or articles of organization within the state where they intend to operate. So it is a relatively easy business arrangement to pull together. Other benefits of the JV arrangement include: • Oportunities to gain new expertise and capacity.• The ability for firms to move into new geographic markets.• JV agreements are not long-term commitments.• Sharing of financial support for a project.• Sharing of financial risks within a project. between the partners.• Can complicate dispute resolutions with the owner and between partners"

Jan 1, 2014

By Staff

"In 2014, the estimated value of total mine production of nonfuel minerals in the United States increased. The quantity of production increased for most mineral commodities mined in the United States, as did prices. Notable exceptions were the declines in prices for most precious metals. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Following the reduction in construction activity associated with the 2008- 2009 recession that continued through 2011, the construction industry continued to expand in 2014, with increased production and consumption of cement, construction sand and gravel, crushed stone and gypsum, mineral commodities that are used almost exclusively in construction. Other segments of the nonfuel minerals industries increased as well. Trends in other sectors of the domestic economy were similar to those for industrial mineral production (Table 1).Discussion of mine production is frequently segmented according to the type of materials produced within the broad categories of metals and industrial minerals. Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. The materials with the highest unit values, usually metals, tend to have very low production rates compared with those of many low-valued materials, such as crushed stone or construction sand and gravel. Therefore, for discussion and analysis of the performance of the minerals industry in general, the value of production is used rather than tonnage produced. Although the value of metals and industrial minerals mined in the United States are similar, if tonnages are compared, construction aggregates dominate, dwarfing the production of all other minerals combined.Mineral industry performanceThe estimated value of nonfuel mineral raw materials, including metals and industrial minerals, produced at mines in the United States in 2014 was $77.6 billion, a 3.5-percent increase from $75 billion in 2013 (Table 2). Net exports of mineral raw materials and old scrap were $15 billion (Fig. 2). Domestic raw materials, along with domestically recycled materials, were used to process mineral materials worth $697 billion. These mineral materials, including aluminum, brick, copper, fertilizers and steel, and net imports of processed materials (worth about $41 billion) were, in turn, consumed by downstream industries with a value added estimated to be $2,530 billion in 2014.In the United States in 2014, mine production of each of 14 mineral commodities was worth more than $1 billion. These were, in decreasing order of value, crushed stone, copper, gold, cement, construction sand and gravel, iron ore (shipped), industrial sand and gravel, molybdenum concentrates, phosphate rock, lime, salt, zinc, soda ash and clays (all types)."

Jan 1, 2014

By Jake Gibson

"As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action toward decreasing greenhouse gas (GHG) and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel, accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery-powered ac systems and diesel-fired heaters, going noidle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, standalone mobile equipment HVAC.The history of GHGs and climate changeIn 1896, Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960s, Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Fig.1).In 1988, the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgment of a rising global annual temperature. The IPCC consists of more than 2,500 scientific and technical experts from more than 60 countries. Because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998, requiring all participating countries to reduce their GHG emissions by at least 5 percent from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States). In 2002, the Bush administration announced a policy for climate change relying on domestic, voluntary actions to reduce the "greenhouse gas intensity" of the United States economy by 18 percent by 2012. The U.S. still attends the Kyoto conference of parties (COPs) but does not participate in negotiations, as it is not bound by its terms."

Jan 1, 2014

By Y. Luo

In designing and operating underground room-and-pillar coal mines, it is always difficult to achieve a good balance between preventing surface subsidence and achieving high recovery ratio. In this paper, a design methodology applying the pressure arch theory is proposed, and the principles and mathematical models involved are detailed. A computer program was developed to carry out the design optimization process and was applied to the examination of a documented case in which a massive cascading pillar failure had occurred over a large area in a shallow coal mine. The results indicate that the proposed design method can be applied to prevent subsidence while achieving reasonably high recovery ratio for roomand- pillar mining operations.

Jan 1, 2014

By J. Morris, R. Sellaro

Petro-diesel is a common collector for coal flotation, but the partitioning of diesel range organics (DROs) in process streams has not been widely studied. Preliminary research suggested that under normal dosing schemes total residual DRO contents in process waters should be limited to the sub-ppm water-soluble fraction (WSF). Further, polycyclic aromatic hydrocarbons (PAHs) should partition proportionately with DROs. The purpose of this study was to confirm these findings in laboratory flotation tests. Total DRO and specific PAH contents were measured in the waters associated with the concentrate and tailings streams. The results show that concentrate waters consistently had higher amounts of DROs than tailing waters. Moreover, the DRO contents in both streams generally increased with increasing diesel dosage. In line with preliminary research, DROs appeared to be limited to the WSF, and PAHs tended to partition proportionately with DROs. Under typical operating conditions, it appears that residual DROs should not present an environmental concern, but conditions should be avoided that allow significant overdosing of diesel.

Jan 1, 2014

By B. Waterman, D. Ramey, L. Schlink

"Water is a primary commodity for most industrial processes. It has become a global focus in light of climate change and population growth. Reuse of process water has two major benefits - minimize the amount of fresh water added now and minimize the amount of discharge water that requires treatment later.Mining and mine product processing has its share of reused water. For example, reclaim water from a tailings impoundment, overflow from thickeners and leach solution to raffinate and back again all demonstrate the use and reuse of water in mining circuits. Eventually, a mine reduces production or ceases operations completely, eliminating the option to reuse the impacted water and, thus, requires treatment of the remaining water.Current methods of water treatment remove the impacts, providing clean water for discharge, but leaves behind a concentrated waste that requires further treatment or disposal of a hazardous waste. Freeport- McMoRan is currently testing three water treatment technologies specific for sulfate and/or metal removal from mine impacted water with the approach of transformation not concentration. These technologies provide clean water for alternative use while creating byproducts that could be marketable, or disposed as a nonhazardous material, thereby reducing the cost and longterm liability of disposal.The selection of a water treatment process is site-specific. The volume of water, contaminant to be removed, disposal options, length of time for treatment, location of plant and reagents and discharge requirements are some of the factors that need to be considered when selecting a water treatment process. Common water treatment technologies for mine impacted water consist of low- or high-density sludge (LDS/ HDS), reverse osmosis (RO) and evaporative technologies. In addition to operating costs, these processes require additional handling of the concentrated sludge or brine. Advanced water treatment technologies include ion exchange, solvent extraction and metals precipitation with or without the aid of a biological system. Some of the more complex systems have a series of unit operations to achieve required discharge regulations."

Jan 1, 2014

Gaby Copper Mining?s Gabriela Mistral property is located in the Antofagasta region of northern Chile, at an altitude of 2,660 m (8,727 ft) above sea level. The reserve contains an estimated 562 Mt (620 million st) of oxide ore with an average grade of 0.41 percent total copper. The mine went into production in 2008. Gaby Copper faced the problem of having no reliable way to measure the solids level. This is a challenge that exists throughout the mining industry, where dust in the air and accumulation of solids on a sensor make accurate measurements difficult in areas such as transfer chutes, the rock box underneath crushers, silos and anywhere else that information is needed on the level of solids. The next-generation technology in the Sitrans LR560 radar from Siemens addresses this challenge. With a frequency of 78 GHz ? higher than previous generations of radar ? it provides a more robust signal for measuring in areas where there are high levels of dust accumulation. The Sitrans LR560 provides a signal beam angle of four degrees, significantly narrower than any other product on the market can offer.

Jan 1, 2014

By Jeffrey A. Yonkey, Timothy J. Lutz, Jacob L. Carr, Christopher C. Jobes

"Since 1984, there have been 39 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM). In January 2015, the U.S. Mine Safety and Health Administration (MSHA) finalized a regulation to require proximity detection systems on all continuous mining machines except full-face machines (MSHA, 2015). Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHAapproved proximity detection systems are commercially available.NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system (Schiffbauer, 2002) and have recently conducted research intended to develop more advanced proximity detection technology for CMMs (DuCarme et al. 2013; Jobes et al. 2012; Carr, DuCarme et al. 2013 and Carr, Li et al. 2013). In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate (Li, Carr et al. 2013 and Li, Jobes et al. 2012) and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators (Carr et al. 2010 and Jobes, et al. 2012).To evaluate the performance of proximity detection systems implemented in industry, NIOSH researchers conducted tests in 2013 on three systems installed on CMMs at three underground mines in Illinois and West Virginia. The results of these tests indicated that, while generally consistent performance was observed, there were opportunities for improving performance. These results were presented at the 2014 SME Annual Meeting (Carr, Lutz, et al. 2014). Since that time, second-generation systems have become available to the industry and are becoming more commonly used.Beginning in early 2014, NIOSH researchers conducted underground testing of these secondgeneration proximity detection systems installed on CMMs. Five tests were conducted on four installations of second-generation proximity detection systems, with one installation being tested twice. The tests were conducted at mines located in Illinois, Virginia and Kentucky with seam heights ranging from 137 cm (54 in.) to 213 cm (84 in.). These tests were conducted using the same test protocol used during first-generation testing, which is summarized in the following section."

Jan 1, 2014

By M. Westendorf, T. Banerjee, S. Kaushik, D. Tinney

"Cyclones are one of the most extensively used pieces of equipment within the mineral processing industry because of their simplistic operating and maintenance philosophies. They are commonly used as classifiers within the comminution circuit to control the grinding product particle size for satisfactory performance of downstream operations.Cyclones are a key contributor to the effective operation of the plant and have a significant impact on the mineral processing plant operations. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput. Similarly, an inefficient cyclone operation may also lead to low or high recirculating loads that impact the efficiency of the comminution circuit. This highlights the importance of having proper stability in cyclone operation while implementing any plant-wide optimization strategy.One of the key challenges in cyclone operation is that cyclones are highly sensitive to changes in operating conditions and are affected by process fluctuations such as feed pressure, solids concentration and flow rates. Fluctuations in cyclone feed characteristics lead to unstable cyclone performance which affects mineral liberation. For such an impactful unit operation, cyclones have historically been under-instrumented in an otherwise highly instrumented process plant. Traditionally, mill operators have relied on visual observations of the apex discharge to determine the operating state of the cyclones. Visual cues corresponding to the different cyclone operating conditions have been discussed by Neesse et al. (2004) as shown in Fig. 1."

Jan 1, 2014

By W. G. Pariseau

"The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to the start of mining in the south barrier pillar. Subsequent loss of ground control in August 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterward three rescue team members. A U.S. Mine Safety and Health Administration (MSHA)report describes the events in detail (MSHA, 2008).An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools and selecting the right tool for the job is essential. In this regard, minimum program requirements include capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses.The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two-dimensional finite element analysis indicated pillar safety was by no means assured (MSHA, 2008; Pariseau, 2008; Pariseau, 2011). Geometry of barrier pillar mining is limited in two dimensions for example, crosscuts are not seen in vertical cross sections. While three-dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three dimensions. This technique involves a dual node - dual mesh concept. Both have been used separately in much earlier work, but are only now used in combination. It is possible to have an estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale (Pariseau, 2014). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2014

By J. Seiter, S. Cox, E. Kim

Mining has always been among the most hazardous of occupations, and with the increasing demand for coal and minerals, safety in mines assumes even greater importance. Worldwide, underground miners are being exposed to noise and respirable dust hazards associated with roof bolt drilling. These hazards are now being understood to cause irreparable damage to the health of miners. The objective of this research was to discover if a polycrystalline diamond compact (PDC) drill bit generates less respirable dust and hazardous noise than a competing tungsten carbide (WC) bit in dry vacuum drilling. In order to control the drill parameters the drilling tests were conducted in a laboratory setting. The results were obtained by determining the quantities of dust and noise generated using each drill bit and analyzing those levels, using monitoring devices and software to collect the data. This paper includes information on the experimental setup, equipment used, drilling parameters, and data collected. Our results indicate that PDC bits produce significantly less noise and dust than WC bits. Our findings can contribute to improving the working conditions of rock bolter operators by reducing noise and dust generation.

Jan 1, 2014

By L. A. Alcorn, H. E. Camargo, G. Gwaltney

"Una de las enfermedades más extendidas en la industria minera es la pérdida de audición inducida por el ruido. La exposición de los mineros a niveles de ruido superiores a los niveles de exposición permisibles resulta en la pérdida de audición de aproximadamente el 80% de los mineros del carbón a la edad de jubilarse. En este contexto, el Instituto Nacional para la Seguridad y Salud Ocupacional (NIOSH, por sus siglas en inglés) está realizando investigaciones para desarrollar controles de ruido aplicados a los sistemas de minado de tajeos largos. Este método de minado es usado para extraer la mitad de la producción nacional de carbón subterránea. A partir de las mediciones en campo, se determinó en investigaciones anteriores que los componentes dominantes que generan sonido en el cizallador de un sistema de tajeos largos son los dos tambores de corte utilizados para extraer el carbón. Debido a las dimensiones y complejidad de los sistemas de minado de tajeos largos, el proyecto NIOSH desarrolló un modelo de elementos finitos validado del tambor de corte para utilizarlo en la predicción del sonido generado por este debido a las fuerzas de excitación experimentadas en las operaciones subterráneas. Este mismo modelo se utilizará para desarrollar controles de ingeniería para el ruido del tambor. Las fuerzas de excitación surgen de la interacción de la broca de corte y el carbón, y se transmiten al tambor de corte a través de los sujetadores de brocas. Debido a las condiciones adversas en el frente y la falta de instrumentación aprobada para uso subterráneo, las fuerzas operativas de corte de carbón no han sido evaluadas anteriormente. Para este fin, NIOSH, en colaboración con la Universidad Tecnológica de Michigan, desarrolló una broca instrumentada autónoma con seguridad intrínseca para medir estas fuerzas. Este artículo describe el desarrollo de la broca instrumentada y la medición de las fuerzas operativas de corte de carbón en tres minas. Las mediciones revelaron que las fuerzas tienen un espectro plano, algo característico de la naturaleza del impacto de estas fuerzas, hasta alrededor de 100 Hz. Por encima de esta frecuencia "cutoff", la magnitud de la fuerza disminuye a una razón proporcional al cuadrado de la inversa de la frecuencia."

Jan 1, 2014

By Sean Masse

New Gold?s New Afton Mine, located 8 km (5 miles) west of Kamloops, British Columbia, is a 4.5-Mt/a (5-million stpy) block cave mine, making it the highest tonnage underground hard rock mine in Canada. The reserve is estimated at 52.5 Mt (55.9 million st) with grades of 0.65 g/t (0.02 oz/st) gold and 0.93 percent copper (2012). Commercial production was achieved in July 2012 and nameplate production was achieved ahead of schedule in September 2012, with the cave breaching to surface in 2013. The mill has a SAG and a ball mill with a froth flotation circuit.

Jan 1, 2014

By K. W. Harris, K. A. Perry

Reserve depletion in Central Appalachia is continuously creating unique ground conditions for underground coal mines with many of these difficult environments directly attributable to multiple seam mining and/or deeper overburdens. While many empirical studies have been performed in an effort to improve understanding of these problems along with potentially improving safety and extraction, many of the difficulties encountered lie outside of the normal realm of expected behavior. This is often the case when mining in bump prone ground, where additional concerns are introduced and design buffers are warranted. The boundary element software LaModel was used to study three bump events in a deep-cover, multiple-seam reserve located in Harlan county in the Kentucky region of Central Appalachia. This region is notoriously bump prone due to significant areas of deep cover, the presence of strong to massive lithology (such as sandstone), and an extensive history of underground mining that increases the probability of multiple seam interactions. Multiple seam interactions are best understood with respect to site-specific parameters, including both the geological and geometrical components of interburden, overburden and mine workings. Initially, empirical-based approaches (ARMPS/AMSS) were used when attempting to back-analyze the bump events. However, it was recognized that a more detailed investigation was necessary to understand the fundamental causes/conditions associated with the bump events. Consequently, the LaModel study resulted in a mine-specific calibration method for the reserve. With this method in place, enhanced bump prediction throughout the reserve is expected, such that the stability, recovery and safety of future mining may be improved.

Jan 1, 2014

By A. H. Farazi, C. Quamruzzaman

The freezing and subsequent solidifying of unstable, weak (sands, silts and clays) and/or wet soil to form a desired-shape frozen barrier around a construction area are possibly the main features of the freezing method for shaft sinking. The barrier, along with strengthening the soil, provides a dry environment to ensure sustainable subsurface construction work before placing a permanent lining. The freezing method requires the installation of freezing pipes in boreholes around the construction area and the circulation of chilled salt water through these pipes and has long been a proven technique for dry shaft sinking through unstable and water-bearing seam around the world. As removing heat from the ground is the main feature of the method, an efficient thermal design of the freezing process is mandatory to ensure success of the shaft sinking operation. This applies to both the sustainability and economy of the intended structure. The design presented in this paper is aimed at figuring out the heat-removing ability and operating time of the refrigerative equipment using some simple formulae. The authors adopted a theoretical approach to determine the quantity of heat to be removed from the ground. The amount of energy for the equipment was found to be greater than that for freezing, which proved the validity of the design. The active freezing period was calculated to be 121 days. The authors followed the structural design of the freezing process they proposed in their previous work (Farazi and Quamruzzaman, 2013). Though the first coal seam in the coalfield was encountered at a depth of approximately 352 m in the subsurface, the target depth for cooling and freezing was decided to be 162 m. The formation demands extra care to nullify its risk of the temporary structure collapsing and water rushing in (Farazi et al., 2012). Discussion on the determination of refrigerative equipment parameters was excluded from the scope of this work.

Jan 1, 2014