Search Documents

By K. Nielsen

The Norwegian tunnelling industry has made remarkable improvements both with regard to productivity and cost efficiency over the last 30-40 years. This development has been made possible by continuous improvement driven by innovation. Based on a generic description of the innovation process and the innovation system, the paper has used the development of modern tunnel drilling in the Norwegian tunnelling industry to discuss the characteristics of its innovation system with a focus on human capital issues and knowledge management.

Jan 1, 2006

By S. Ash

Murray mine was one of the first Mechanized cut and fill underground gold operations in Northern Nevada. At the end of 2002 mine production began to decline and Murray entered a phase of remnant mining and began preparations to close down. The remaining mining took place along the ore waste boundary, in previously condemned areas, and in highly challenging ground conditions. To remain economically viable new techniques were implemented in operations, geology, engineering, and rock mechanics. These improvements pushed the edge of known and accepted mining practices and have allowed Murray to remain in operation today. History The Murray mine is located on the Jerritt Canyon property, which is located 45 miles north of Elko, NV in the Independence mountain range. Mining operations started at Jerritt Canyon in 1980 out of several open pits. In 1993 underground mining began in conjunction with a decline of surface mining operations. The transition from surface mining to underground mining moved the property into a new era. At the time there were limited examples of successful underground operations in the area from which to draw experience. Several mining methods were attempted with varying degrees of success and underhand cut and fill proved to be the most effective method. To date Murray has mined 1.2 million ounces at an average grade of .335 OPT utilizing this mining method.

Jan 1, 2006

By M. Di Tommaso

Acid Mine Drainage (AMD) is a quite diffuse environmental problem in dismissed sulphur mine districts. AMD is related to sulphur oxidation of abandoned tailings, generating heavy metal-bearing streams with high iron and sulphate contents and low pH. Treatments of AMD aim firstly to increase the pH to reduce its leaching power causing the further release and mobilization of heavy metals through soil solution and groundwaters. Increasing the pH also allows the precipitation of iron (III) (involved in sulphur oxidation and then in AMD generation) and the partial removal of other toxic components such as arsenic. pH adjustment and the reduction of the high concentration of iron are also necessary for the successive biological treatment in permeable reactive barriers (PRB) with sulphate reducing bacteria (SRB) (II step, biologically mediated precipitaton/biosorption) to avoid the rapid plugging of the barrier (for the large amounts of iron precipitates) and to ensure neutral pH conditions for SRB growth. In this work the first step (chemical precipitation) of a combined chemical and biological treatment of AMD is presented. Experimental data from column tests using carbonate stones to remove iron and increase pH were reported. Toxicity tests have been carried out on the treated wastewaters by Lepidium sativum.

Jan 1, 2006

By Louis W. Cope

Mongolia is known in western countries as the location of rich dinosaur fossil fields. However, the country is even richer in mineral resources. The Ministry of Industry and Trade reports 6,000 mineral occurrences of 80 metals and minerals. Mongolia has already attracted much foreign investment in the mining sector. Mining is the country’s largest industry. It is responsible for 17 percent of the gross domestic product, 65 percent of industrial output and 57 percent of export earnings.

Jan 1, 2006

By W. G. Pariseau

Introduction Caverns of 50 m in linear dimension at depths below 2300 m with a life of more than 25 years are proposed for the next generation of water-filled neutrino detectors. Little precedent exists for excavations in such an extreme environment, although some guidance is available from mining experience at great depths, for example, in South Africa, in Canada and at the former Homestake Mine in the U.S.A. Unlike mining for ore, there are choices available in the construction of such caverns that may mean the difference between success and failure. These choices should be informed by rock engineering principles. Recently proposed guidelines for orientation of brick-shaped caverns where the long dimension is a small multiple of the short dimension indicate that the most favorable orientation is with the long and short dimensions parallel to major and minor preexcavation principal stresses (Pariseau, 2005). Numerical analyses at reduced strength indicate some yielding at cavern walls should be expected but that an equilibrium state is quite possible and is aided by arching the back into a spherical dome when the cavern is an empty cylinder (Tesarik and others, 2002). The same indications of stability occur with brick-shaped caverns. However, the most dangerous situation occurs during the excavation sequence to final cavern dimensions. There are any number of excavation sequences that lead to the same final cavern shape, so there is an opportunity to partially optimize the sequence with construction guidelines that minimize peak stress concentrations during construction. This contribution discusses three practical excavation sequences that lead to the same brick-shaped cavern in the strong, massive Yates formation at the Homestake Mine where considerable rock mechanics data has accumulated through the years(e.g., Pariseau, 1985, Pariseau and others, 1995) and where actual mining on the 8000 Level indicates a strong possibility of successful investment in the next generation of large, deep neutrino detectors. The main results are: (1) a favorable brick-shape is one with dimensions in the same proportion as the preexcavation principal stresses (compressionpositive), and (2) favorable orientation of the most extreme but temporary shape of excavation is also best for the construction sequence. Analysis results from a mix of Homestake Mine data and possible excavation geometry illustrate the advantages of these guidelines.

Jan 1, 2006

Your assessment of the minerals business. I would first like to express our profound sadness and sincere condolences to the families of the miners who lost their lives in recent mine mishaps particularly in West Virginia, and other locations. Any loss is unacceptable. It is time to review and, if required, re-establish a rigorous health and safety agenda in the mines. It must involve a review of health and safety regulations. And innovative training methods for sensing, awareness and mitigation of health and safety hazards must be developed. As far as the minerals business is concerned, I am excited about the outlook for mining. Over the last 20 years, global demand for minerals has closely mirrored the growth of the gross domestic product. Minerals re-main a major part of the world’s economic foundation. And that will continue to be the case. It is no surprise that the fortunes of the mining industry rise and fall with general economic trends. Globally, mining has been strong — thanks to the explosive economic growth in Asia. The U.S. mining industry has performed reasonably well, with notable strength in the metals, coal and construction and aggregate areas and with some softness in the industrial minerals sector.

Jan 1, 2006

By G. Adel, J. M. Richardson

Mine-to-mill optimization is a holistic approach to the optimization of mining and processing operations. Developed at the Julius Kruttschnitt Mineral Research Centre, it attempts to minimize energy consumption through the optimization of the particle size reduction process. The approach involves sampling and modeling of blasting and processing, computer simulation to optimize the operation and develop alternatives, implementation of the most promising alternatives, and sampling to quantify energy savings. The primary objective of the present effort is to adapt mine-to-mill technology to the aggregates industry. This paper presents an update of work being conducted at quarries operated by the Luck Stone Corporation of Richmond, Virginia.

Jan 1, 2006

By M. Galetakis

This paper proposes a new approach for calibration of dual gamma-energy transmission (DU-ET) ash analyser for improved online analysis of run-of-mine lignite. An adaptive neuro-fuzzy inference system (ANFIS) was developed to model the relationship between the intensities measured by the scintillation counter of the analyzer and the measured ash. Samples collected from Megalopolis lignite mines were measured for their ash content by using standard laboratory methods as well as by DUET. Obtained data was divided into training, testing and validation sets. A first order Sugeno type ANFIS was used in conjunction with early stop training. The calibration performance obtained by this approach was significantly better compared with that obtained by standard calibration methods based on multiple linear regression analysis.

Jan 1, 2006

By Leigh Freeman

This article provides an overview for a series of leadership development workshops offered through the SME Young Leaders Program. The first of these workshops, “Accelerated Development Plan,” will be held at the upcoming SME Annual Meeting in St. Louis, MO on Sunday, March 26. How does a foundation of technical competencies relate to the development of social competencies necessary for management and leadership roles in the resource sectors? Technical competencies provide the foundation for a successful career. Social competencies provide the framework on that foundation. Successful leaders will be those who develop competencies in all areas.

Jan 1, 2006

By A. Exikis

Simulating a ventilation network of an underground mine can help in solving complex ventilation systems with many features, selecting proper fan specifications, location and settings. Early computer systems running simple network simulations were able to provide solutions to the most common and immediate problems regarding underground mine airflow. The more advanced systems available today can perform more sophisticated modeling and simulation of a mine?s ventilation network and present their results in a more understandable and easy to communicate form. This paper presents a ventilation network case study from an underground mine. All aspects of mine ventilation network modeling and simulation are discussed as well as the results from the simulation process. The algorithms and techniques used are thoroughly explained. Some useful guidelines for the application of ventilation network software are also provided in the text.

Jan 1, 2006

By D. X. Tang, G. Wilson, S. S. Peng

Design and implementation of a roof bolting plan requires reliable geotechnical information of strata, such as rock strength, and locations of interfaces and voids/fractures. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way to gather information on the geological structure within the bolted horizon. The purpose of this research project is to develop a method for identifying the geological features in the mine roof strata based on drilling parameters of roof bolter. The criterion for void/fracture prediction has been developed and proven valid. This paper focuses on the estimation of the strength of roof strata by using drilling parameters. Based on the results of a series of underground and laboratory tests, feed pressure is found to be the most sensitive parameter when the strength of roof strata changes. Moreover, it was also found that both penetration rate and rotation rate have obvious impact on the magnitude of feed pressure. Based on these findings, the criterion for the estimation of roof strata strength has been developed using the relationship among feed pressure, penetration rate and rotation rate and implemented in MRGIS.

Jan 1, 2006

By K. Kavouridis

The competitiveness of power production from lignite depends on the ability of coal industry to meet CO2 emissions limits, as specified by the Kyoto protocol. According to the National Allocation plan issued by EC, power plants should reduce CO2 emissions to a certain level, other-wise they will be obliged to cover the difference buying CO2 certificates through the Emission Trading Scheme. These charges will increase the operating cost of current units, as well as the investment cost for new units. To predict the increase in the marginal cost of electric power produced from the current plants of Western Macedonia, an emissions factor (CO2 t/MWh) for various units has been computed. Based on the algorithm used, this factor depends on the calorific value of the lignite, the efficiency of the power plant and the oxidation factor of the unit. For lignite plants with efficiency ~37%, CO2 emissions factor ranged from 1.19 t/MWh to 1.32 t/MWh. The increase in the marginal cost of kWh, as compared to the values of CO2 certificates, is higher in units fed with low quality lignite and worsens if the efficiency of the unit is low too. Also the presence of calcareous minerals in lignite increases the CO2 emissions and consequently the cost of power generation.

Jan 1, 2006

By A. E. Foscolos

British Petroleum (BP, 2005), indicates that world reserves for oil to be 1198 billion barrels, for natural gas the equivalent of 1156 billion barrels of oil and for coal the equivalent of 3219 billion barrels of oil. If we take into consideration the mean aver-age annual increase in demand of the last three years for oil, 2.6%, for natural gas, 3.9%, and for coal, 6.6%, then their respective reserves? lifespan are calculated to be 27, 34 and 38 years. Without taking into account their annual increase in demand, lifespan increases to 38, 67 and 161 years respectively. Since zero increase or perpetual increase in energy demands on finite resources is unrealistic the selection of the most suitable energy commodity for power generation rests upon the law of supply and demand of each commodity. This defines its price hence its selection for the production of cheap electricity. When the ratio of supply to demand is less than one, peak production is achieved. Any further increase in demand results in price increase to quench its demand. The Association for Oil and Gas Peak (ASPO) has calculated that when oil demand exceeds 84 million barrels/day, Peak Oil Production will be attained thus prices will start to increase in order to even demand with supply. Correspondingly, Gas Peak Production is expected to take place when demand exceeds 9.1 or 10.2 billion cubic meters/day. Peak Oil production has been calculated to take place in the current year, 2006, while Gas Peak production is estimated to take place between 2020 and 2025 provided that gas will not cover the energy deficit created from the lack of oil otherwise Gas Peak production could arrive as early as 2010. The use of coal for power generation is considered a better alternative than oil and gas if new combustion technologies with an energy efficiency of 43%, Germany, and 47%, Denmark, are adopted. These not only extend the lifespan of coal reserves but reduce also CO2 emissions by 25% and 31%, respectively. In the very near future CO2 sequestration and fixation in deep geological strata will eliminate its emissions thus rendering the use of coal the cheapest feedstock for power generation.

Jan 1, 2006

By W. M. Hart

Business Process Improvement (“BPI”) Change to Survive “It is not the strongest of species that survive, nor the most intelligent, but the one most responsive to change.” [Charles Darwin] “If you want to understand something, try to change it.” [Kurt Lewin, social scientist] Many companies have tried one or more process management initiatives. Each effort may help develop a culture that is more receptive to change. Executive Management needs to be unwavering in support of change with systems and structures, staffing, development of people, measures, with incentives and rewards. General Electric developed principles for quality change management that are necessary for effective, continuing Business Process Improvement (BPI). Change Acceleration Process (“CAP”) One of the tools General Electric developed has been used successfully by companies around the world in a wide variety of industries. This tool, named Change Acceleration Process (“CAP”), is designed to improve acceptance of change. Acceptance is the method by which the creative energies of the workforce can be fully tapped. Over time, every employee receives CAP training at least once, and in many instances three (3) or four (4) times, and will work on one or more High Performance Teams. Thus, BPI can achieve and maintain its goals. The CAP tool focuses on: • Leading Change • Creating a Shared Need • Shaping a Vision • Mobilizing Communication • Making Change Last • Monitoring Progress • Changing Systems and Structures

Jan 1, 2006

By William R. Yernberg

The combined 79th Annual Minnesota Section of SME Meeting and 67th Annual University of Minnesota Mining Symposium was held April 11 and 12, 2006, in Duluth, MN. About 300 mining professionals attended, including engineers, executives, mining managers and suppliers, from throughout the United States and Canada. This year’s theme was “Success in the New World of Mining.” The SME Minnesota Section meeting included a keynote session, a special projects update, a general managers update and technical paper presentations. The University of Minnesota Mining Symposium program featured a panel discussion on Minnesota’s relationship with China. The combined meeting included a trade-show consisting of 64 booth spaces. Tradeshow demand exceeded expectations, and an additional 10 booth spaces were added in the registration lobby. Also included were an SME short course on pump basics and social events.

Jan 1, 2006

By N. S. Tombs

This paper presents the experimental results of an ongoing investigation into various properties related to the performance and durability of concretes made using existing and new cement replacements. The process of cement and concrete production is investigated focusing on product performance and environmental performance. The overriding factor for the progression of a material will be product performance however; each material selected will have many intrinsic environmental benefits. The study combines Ordinary Portland Cement (OPC) with each cement replacement candidate using the most common replacement percentages, 10, 20, 25, 30 and 50 percent. A 35N/mm2 concrete is then prepared and analysed in the fresh and hardened state. In addition, a chemical and physical analysis of each replacement material has been performed and results compared to the control samples containing OPC only and Ground Granulated Blast Furnace Slag (GGBS) as a replacement. The results show that in their present form the replacements used in this research do not compare with the strengths achieved by the controls. The right balance of chemical composition and particle grading needs to be achieved to produce a realistic replacement material. The processes required to achieve this must strike a balance between monetary and environmental cost.

Jan 1, 2006

By J. Loredo

Wastes related to abandoned mine sites can constitute important potential pollution sources, depending on their mineralogical and geochemical characteristics and volume. Mine waste disposal sites contain a diverse variety of wastes including overburden material and waste rocks, the ore which cannot be economically removed and wastes from the smelting processes when they are accomplished at the mine site. These materials are usually heterogeneous in size, mineralogy and metal concentrations. Asturias, in northern Spain, has an extensive mining history and, in consequence, there are abundant unreclaimed and derelict mine sites with abandoned mines and spoil heaps of different age, morphology, content and dimensions. In these spoil heaps, waste materials are subjected to the intense action of a humid environment, so the instability of sulphides and sulpharsenides results in the production of acid and metal-rich leachates, which are incorporated to surface water or infiltrated through the land reaching groundwater bodies. The mineralogical and geochemical characteristics of the stored materials are key data to evaluate if they represent an environmental risk. Mineralogy and geochemistry of wastes and the particular specific environmental conditions of each site affect the rate of weathering and therefore the metal release. The characterisation of mine wastes is a necessary step in order to establish suitable assessment strategies with the aim of reducing the leaching, transport and widespread of ecotoxic elements from mining wastes to the environment (surface water, sediments, soils and air). As a consequence of the weathering of As-rich mineral phases, high arsenic contents are commonly detected in effluents from mine voids and spoil heap leachates.

Jan 1, 2006

By S. Triantafyllidis

The tailings produced from the Kirki (Agios Filippos) high sulfidation epithermal deposit processing plant are laminated, weakly cemented and their particle size ranges from fine sand to fine silt. They are mainly composed of milling residues of gangue (quartz, dickite/kaolinite, pyrophyllite, illite); sulfides and secondary minerals (jarosite group minerals, butlerite, anglesite, beudantite and gypsum) are present to a lesser extent. They have high Pb and Zn (average 0.75 % and 0.57 % respectively) and low S (1.04 to 2.92 %), Cu, As, Cd, Ni and Sb content (average 248, 163, 59, 27, 20 g/t respectively). Stagnant waters forming small ponds on the surface of the impoundments exhibit low pH and high heavy metal and sulfate concentrations. Negative Net Neutralization Potential (NNP) characterizes the tailings, indicating moderate to high potential for acid generation. Application of the TCLP test revealed that the tailings are characterized as toxic because of the increased solubility of Pb and Cd. On the other hand, As TCLP solubility is very low.

Jan 1, 2006

By Paul D. Tomlingson

World class performance is the ultimate objective of many maintenance organizations. It marks the organization as a leader in its industry and sets it apart as the ultimate achiever. But what is a “world class” standard and how can it be achieved? Is there a yardstick by which an industrial organization can measure the relative performance of its maintenance activity and compare it with performance levels that universally identify “world class” status? Are there financial formulas, achievements, evaluation techniques or indices that provide this yardstick?

Jan 1, 2006

By William R. Yernberg

The 2006 North American Tunneling (NAT) Conference was held June 10-15, 2006, in Chicago, IL. The biennial conference was the first NAT conference by the newly formed Underground Construction Association of SME (UCA of SME). The UCA of SME was formed earlier this year at the request of members of the American Underground Association (AUA) (ME, April 2006, page 75). The conference included a keynote session, technical programs, workshops, a trade show and social activities. The conference exceeded expectations with 570 attendees. They included engineers, equipment manufacturers, representatives from government agencies and other interested individuals in the underground construction industry. The trade show was also a success with more than 86 booth spaces sold. Vendors included the biggest names in the underground construction and tunneling industry and included equipment manufactures, construction contractors and engineering companies. The trade exhibition provided a forum for interested parties in the tunneling industry to meet and discuss services, equipment and techniques.

Jan 1, 2006