Search Documents

By D. Royston

A novel low-cost technology is described that treats excavation waters in estuarine environments where water coloration due to humic material is present, along with acidity, turbidity, sediment and salinity. The process treats all the components in the water to produce a clear (color-free) water stream that meets requirements for direct discharge to local estuarine waterways.

Jan 1, 2003

By K. S. Mortensen

The softwall mining system is a novel, new method of mining mineral deposits in soft, shallow, nonrock ground conditions. This method can mine the ore layer without substantially disturbing the existing overburden. The softwall mining system consists of machinery that is hydraulically controlled and powered, that can be buried (or used on the surface) to extract the ore or mineral from a layered deposit. The method is essentially an application of the longwall mining concept, modified for loose overburden and ore conditions, combined with hydraulic mining.

Jan 1, 2003

By W. Petruk

Imaging is a fundamental requirement when characterizing minerals, ores and related products. Images are used for presentation, texture analysis, characterization, image analysis, identification, etc. The image mode that is utilized is dependent on the application, mineral properties and available instruments. Different instruments produce images that display different features. In order of increasing complexity they are: hand specimens, a non-polarizing microscope, polarizing optical microscope, scanning electron microscope (SEM), low vacuum SEM, microprobe, secondary ion mass spectrometer, staining, cathodoluminescence, tomography and others. Image analysis uses images produced with either an optical microscope or a SEM, but the SEM images are superior in this application. Key words: Mineralogy, Imaging, Mineral characteristics, Scanning electron microscopy, Optical microscopy, Cathodoluminescence

Jan 1, 2003

By Jakub Nalaskowski, Robert Aranowski, Jan D. Miller, Jan Hupka

The polyolefins, mainly polyethylene and polypropylene particles, are used as an active filler material in polymer-polymer blends and are being used for the modification of asphalts to pro- vide for high-load, low-maintenance road construction. The stability of prepared blends depends on the interaction forces between polyolefinfiller and the matrix and/or between two polyolefin filler surfaces in the polymeric matrix. Various additives, especially surfactants, can be used to modify these interactions and improve the stability of polymer blends. In current research, direct force measurements between polyethylene (PE) surfaces in n-tetradecane, a nonaqueous solvent imitating the polymer matrix, were performed in the presence of lauric acid and dodecylamine using the AFM colloidal probe technique. Additionally, the zeta potential of polyethylene particles in the presence of surfactants in n-tetradecane was measured. The interac- tion forces between the polyethylene surfaces can be described as a combination of electrical double layer repulsion and steric repulsion between polymer chains extending into the n-tetradecane sol- vent. The addition of surfactant to the n-tetradecane was found to increase the repulsive force between the PE surfaces. The strongest repulsion was observed for dodecylamine. Additionally, the temperature efect on the interactions in n-tetradecane was studied. It was found that steric repulsion between the PE surfaces increases with an increase in temperature.

Jan 1, 2003

Published by ?MILOS CONFERENCE CENTER ? GEORGE ELIOPOULOS? Editor Professor Z. AGIOUTANTIS Editorial Coordinator HELIOTOPOS ? PROFESSIONAL CONGRESS ORGANIZERS Layout IRINI KALOGIRU Production PALLAS Co Cover PANAYOTIS PAPASTAMATIS HELIOTOPOS - PROFESSIONAL CONGRESS ORGANIZERS

Jan 1, 2003

By D. R. Babich, E. R. Bauer

Noise induced hearing loss (NIHL) continues to be a problem in the mining industry. New noise standards (Part 62) promulgated by the Mine Safety and Health Administration (MSHA) are aimed at reducing NIHL in the mining industry. The National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of noise sources and worker noise exposures to address NIHL in mining. Noise surveys, including full-shift worker noise exposure and equipment noise profiling, have been completed in several surface coal mines, with an emphasis on draglines. The results of these studies are reported, their implications concerning worker NIHL are addressed, and their application to administrative and engineering controls is discussed.

Jan 1, 2003

By W. Ripmeester

Canada is committed to the development of indicators to measure the contribution of its minerals and metals sector to sustainable development. The Minerals and Metals Indicators (MMI) Initiative is described, including drivers for the development of indicators, the MMI theoretical framework, the multi-stakeholder consultation process utilized in the development of indicators, and possible policy and business implications of MMI.

Jan 1, 2003

By L. F. Ruppert, R. C. Milici

Coalbed methane (CBM) is currently being produced from a relatively small area in the Dunkard and Pocahontas basins, in the northern and central parts of the Appalachian Basin, respectively. In general, much of the production occurs where the coal beds are beneath 500 feet or more of overburden, where the rank of the coal is high-volatile B or greater (%Ro >0.8), and where the natural fracture system is enhanced by structural deformation. It is anticipated that near-term CBM development will continue within these areas and will expand in the Appalachian basin as technology improves and as the price of gas rises.

Jan 1, 2003

By Richard Switalski, Mark R. Kritzer, Boro J. Lukajic, Robert Pintabona

Ground freezing was chosen as an initial support method during construction of two deep shafts at the Mill Creek project. The Mill Creek, Phase 2 tunnel (MCT-2) is utilized to convey and store combined storm and sanitary sewage collected from the member communities in the greater Cleveland area. The main objective of groundfreezing was to provide a strong support structure to resist soil and groundwater pressures. This was achieved by creating a watertight, frozen-ground barrier around the shaft perimeter. The paper will provide an overview of ground freezing techniques applied during the construction of two shafts, each 250-feet deep.

Jan 1, 2003

By J. Loredo

Asturias, in Northwestern Spain, has an extensive mining history. As a result of these historical mine activities where operations have been usually developed with little control on effluents or emissions (environmental regulation of mining activity has only been introduced recently), pollution has been severe in some areas, specially in Hg abandoned mine sites, which constitute one of the major environmental problems related to mining. In many of these sites, materials stocked in spoil heaps can be considered as hazardous wastes because of their chemistry, content on ecotoxic elements and potentiality to spread these to the environment. In the humid climatological conditions of the region, water and wind eroded spoils are dispersed through the environment by different pathways and occasionally surrounding soils and waters are intensively affected by pollution. According to the environmental risks that these unreclaimed mine sites suppose for human beings and ecosystems, remedial options must be considered.

Jan 1, 2003

By L. E. Allen, J. F. Abel, D. R. Morgan

The Waste Isolation Pilot Plant (WIPP) is a geologic repository for disposal of transuranic waste and is operated by the U.S. Department of Energy (DOE). The repository is located at a depth of 655 m in the Permian age salt beds of the Salado Formation, 40 km east of Carlsbad, NM. A key component in the design of the WIPP repository is the installation of concrete structures as panel seals in the intake and exhaust drifts after a panel has been filled with waste containers. The DOE has proposed several panel closure design modifications to the EPA. EPA approval of the changes is required since the details of the designs are specified in EPA’s final rule as a condition for WIPP certification. The Environmental Evaluation Group, in its role of providing technical oversight on the WIPP project, has evaluated the proposed modifications. An analysis of this evaluation is discussed.

Jan 1, 2003

By M. H. Weinecke, B. P. Faulkner

This paper discusses the process for making lightweight aggregate, the waste materials that make good lightweight aggregate, the chemistry of making lightweight aggregate and the commercial prospects for making lightweight aggregate from wastes. Svedala Industries has been making lightweight aggregate (LWA) from waste materials for the last 10 years. Many claylike materials, such as coal fired boiler ash and washings from a granite quarry, can be used alone or with additional waste materials to produce commercially salable LWA.

Jan 1, 2003

By W. K. Utt, C. C. Woodward, W. L. Howie, G. G. Miller

The process of roof drilling and bolting is one of the most dangerous jobs in underground mining. In the United States, roof drilling and bolting results in about 1,000 accidents with injuries each year. Researchers, from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are studying the feasibility of using a drill-monitoring system to estimate the strength of successive layers of rock and assess the integrity of a mine roof. Such a system would allow roof drill operators to be warned when a weak layer is being drilled. Using measurements taken during drilling, a neural network can classify mine roof strata in terms of relative strength. The concept has been proven in principle. This research project was undertaken to increase the safety of underground miners, especially those involved in roof bolting. The system should be applicable to the mobile drills now used in underground mines, and the system would likely find wider application as well.

Jan 1, 2003

By A. B. Seal, C. J. Bise

Excessive noise has long been a hazard in the coal-mining industry. Studies conducted during the mid-1970s and mid-1990s consistently show that hearing loss within the mining industry persists, in spite of regulatory requirements and sampling technology advances. When the U.S. Mine Safety and Health Administration's new health standards to protect miners from hearing loss took effect in September 2000, the potential developed to reevaluate sampling approaches with regard to noise-source hazards, such as task-based methods. This paper describes results from a Pennsylvania State University research project now being conducted at an underground coal mine. Each occupation was reviewed, and a list of tasks or processes performed by each was generated. Traditional personal noise dosimetry, static sound pressure levels and equipment sound mappings have been performed. Job tasks indicating the greatest levels of daily noise exposure and contributions to noise dose have been identified and will be discussed.

Jan 1, 2003

By J. Ke

Traditional geostatistical methods have been used in ore reserve estimation for decades. Neural Networks (NNs) have provided an alternative approach to data analysis and ore reserve estimation. Unlike the traditional geostatistical methods, neural network uses a highly non-linear complex algorithm to do the estimation. Although Neural Networks have been demonstrated to be attractive alternatives as with every new techniques, there are questions which remain unanswered. This paper presents a comparative analysis with different types of metamodeling approaches -- Triangular, Kriging, Spline, and Neural Network. The neural-network is organized in a multiple-layers and Back-propagation model is used to handle the non-linearity and hidden slabs for smoothing the predicted results. With multiple dimensional and very noisy drill hole sample data, the ore grade is predicted and the overall performance is validated by the analysis of R-squared (R2), Root-Mean-Squared (RMS), and contours of ore grade spatial variability. The ore grade and tonnage of estimated outputs are also compared with various cut-off grades.

Jan 1, 2003

By Daniel McConvey

Who is the Investor? -Mainly institutional, including resource funds, other mutual funds and pension funds. -Some hedge funds. -Retail investors. -How important is the reserve disclosure to these investors? -Do these investors know the difference between a reserve and a resource?

Jan 1, 2003

By J. L. Weeks

Discussion by J.L. Weeks Discussion I wish to comment on Kissell and Sacks's paper "Inaccuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines." It is well established in industrial hygiene that area sampling is not an accurate measure of personal exposure. To measure personal exposure, one must use a personal sampler. Kissell and Sacks, using data from coal mining, reached the same conclusion. This is the right answer but it is the wrong question. This issue arises because the machine-mounted respirable dust continuous monitor (MMRDCM) is being considered to monitor coal-miners' exposure to respirable dust. This device may be mounted on a continuous mining machine, and it would take a modified area sample. I refer to it as "modified" because a mining machine is not really a fixed location, as is the typical area sample. The concern with whether this machine would provide an accurate estimate of the machine-operator's exposure, however, overlooks important features of the MMRDCM. Specifically, it displays dust concentration as it occurs and at the place where it is needed, not 10 days later, as is the case with the current system. Used in this way, it allows for timely intervention to control exposure to dust and it leads to greater first-hand knowledge of specific conditions and mining practices that result in excess exposure. If one knows the dust level is excessive at the time the dust is being generated, it is possible to use known and effective methods of dust control to reduce exposure. By measuring again, one can determine whether control methods have worked. This is a generic procedure followed in any industrial process: measure, adjust and measure again. It leads to more effective and more efficient dust control and is preferred to taking a sample, waiting 10 days for the results and then trying to apply that information to a situation that no longer exists. The MMRDCM also records the dust level automatically, and it runs continuously, making it harder to tamper with. Dust monitoring in underground coal mines has been corrupted by some operators having submitted fraudulent samples (and being convicted on criminal charges because of it), weakening the credibility of the current system. The MMRDCM is, in part, a response to this corruption, and an effort to focus attention on dust levels and dust controls rather than on the perpetrators of fraud. Use of the MMRDCM is an evolutionary change from the current system. With the current system, one takes a personal sample of exposure of the "designated occupation" (DO, defined at 30 CFR 70.2 (f)), the occupation regularly exposed to the highest level of dust on a section. Typically, on sections using continuous mining machines, this is the mining-machine operator. The rationale behind DO sampling rests on some of the findings that Kissell and Sacks report. They reviewed several studies that showed that dust concentration varies with location on a mining section and that there is a concentration gradient with the highest concentration occurring closest to the face. The logic behind DO sampling strategy is that if the dust concentration at the place where it is highest is below the exposure limit, then concentration elsewhere on the section is also below the limit. In this way, one will have achieved the objective or keeping dust concentration below the exposure limit for all miners on the section by measuring the exposure of only one miner. The

Jan 1, 2003

By Z. Zhang, R. G. Reddy

The viscosities of industrial lead slags of varying compositions were measured as a junction of temperature using a Brookfield viscometer. Based on the experimental data obtained from this study and based on other investigations reported in the literature, an expression was developed to correlate the viscosities of industrial lead silicate slags as a function of composition and temperature. The effect of each individual slag component on the variation of the slag viscosity is identified. The composition dependency of lead silicate slag viscosity is discussed. The calculated results using this viscosity expression are in good agreement with the measured data. Key words: Viscosity, Lead silicate slags

Jan 1, 2003

By Alwyn Protheroe, Steve Smith, Herbert Jr. Gibson

In September of 2000, Cowin and Company, Inc., contracted with Paramont Coal Corporation to construct a large decline approximately 820 m (2,700 feet) in overall length at a grade of 8 degrees to the Lower Banner Coal Seam. This paper will discuss the methods used by the contractor and owner to overcome the unique problems required to construct this tunnel in a coal mine environment. The problems include, initial design considerations, equipment selection, ventilation, ground control, control of water in?ows, and placement of concrete.

Jan 1, 2003

At present, increasing focus of public perception is placed on the environmental and social benefits, risks and impacts of metals and metal-bearing products. To address these issues, the concept of product stewardship has recently been introduced into the political debate. In this paper, results from a survey of existing environmental and social reporting practice in the copper mining, smelting, refining and fabricating industry are presented. In this context, particular emphasis is placed on the reporting practice regarding products and product performance over the life cycle. In a few companies there has recently been a shift towards adopting product stewardship principles and putting them into action. As part of an ongoing exercise within the Non-Ferrous Consultative Forum on Sustainable Development sponsored by the International Copper Study Group (ICSG) key issues of interest to the non-ferrous metals sector are being addressed. The Forum, for example, has developed a series of principles, criteria and indicators that could form the basis for a voluntary, industry-lead product stewardship scheme. Current achievements and way forward of this product stewardship initiative will be presented.

Jan 1, 2003