Search Documents

Phelps Dodge Mining’s Bagdad, AZ copper facility uses a large series of cone crushers and ball mills to reduce copper ore to very fine particles. The solids are mixed with water to create a slurry. Milk of lime is added to this slurry to raise the pH. Small amounts of reagents are also added, including a frother to make bubbles, as well as a collector chemical that causes the copper minerals to stick to those bubbles. This material is pumped to a series of froth flotation cells to concentrate the copper. Air is blown into the flotation cell tank and the pulp mixture is vigorously agitated. Rising bubbles carry the copper particles over the edge of the flotation tank. The bubbles break after they flow over the edge.

Jan 1, 2005

By I. de Jong, G. Van Weert

Silver cyanide adsorbs extremely well on activated carbons. This suggests that the addition of soluble silver salts to trace cyanide containing waste streams should allow efficient cyanide removal with active carbon. Silver losses, however, would make this method expensive and also objectionable, since silver has biocidal effects. When silver impregnated carbon is used, these problems are overcome. Test work has shown that such silver remains on or in the active carbon, that cyanide concentrations can be reduced to the level of detection (< 5 ppb) and that the silver impregnated carbon can be reactivated with equipment similar to that now in use at gold milling operations. Initial results on the type of carbon, the impregnation procedure and the level of silver, and the effect of repeated regeneration are discussed.

Jan 1, 1992

By William E. Lamont

The Mineral Resources Institute (MRI) of the School of Mines and Energy Development (SOMED), University of Alabama conducted studies to determine the potential for upgrading the Eastern Devonian shales by flotation. Results of those studies indicate that flotation concentrates containing 150 liters of oil/t (36 gal/t) can be produced from shale containing 50 liters of oil/t (12 gal/t) as determined by Fischer Assay with good recovery of the kerogen. Organic carbon and trace elements such as molybdenum, vanadium and uranium also are concentrated with the kerogen. Kerogen concentration was found to be a function of the size of grind.

Jan 1, 1983

By Ray E. Williamson

One of the prime objectives of the mine industry is to develop a low cost way to clean up what has been called "The Rape Of Mother Nature". The project falls under the broad umbrella of reclamation, which is now considered an essential part of the mining cycle. As such, it is being given full consideration in the initial planning of all surface operations. In most areas, if a proposed mining system does not lend itself to proper reclamation, it is not an acceptable system. By combining mining and reclamation plans, a producer not only can minimize reclamation costs, but can also restore the land to usefulness and insure continuing profits after a deposit is depleted. As long as fifteen years ago, many of the larger mining companies were already deeply involved in this extra cost work. Even then the involved companies were projecting a great need for a bigger bulldozer, Bigger than anything commercially available. At that time, the D9 tractor weighed about 60,000# bare weight.

Jan 1, 1975

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. This paper focuses on the KRS Algorithms that extract key information from lists of time study type event sequences. Because a static system cannot operate effectively in a dynamic mining environment, we are prototyping an index based technique that allows the system to adapt itself to this dynamic environment.

Jan 1, 1990

By C. Bise, A. Seal

Excessive noise has long been a hazard in the coal-mining industry. Studies conducted during both the mid-1970s and the mid-1990s consistently show that hearing hearing loss within the mining industry persists, in spite of regulatory requirements and sampling technology advances. When MSHA’s new health standards to protect miners from hearing loss took effect in September 2000, the potential developed to re-evaluate sampling approaches with regard to noise-source hazards, such as task-based methods. This paper describes results from a Penn State research project currently being conducted at an underground coal mine. Each occupation was reviewed, and a list of tasks or processes performed by each was generated. Traditional personal noise dosimetry, static sound pressure levels, and equipment sound mappings have been performed. Job tasks indicating the greatest levels of daily noise exposure and contributions to noise dose have been identified and will be discussed.

Jan 1, 2001

By Paul I. Eimon

Mineral exploration involves the selective collection, organization, evaluation, and interpretation of geologic and economic data. The sources for such data are original field observations and existing documented information of various types (publications, reports, maps, company files, etc.). As exploration data are accumulated, their storage, organization, indexing, and J retrieval is key to exploration progress. Initial use of computers by mineral exploration groups indicates that data can be meaningfully handled by machines. A computer system makes possible: 1) the storage, manipulation, collation, and selective retrieval of data; 2) the utilization of data banks developed by geologic service groups and available at relatively low cost; and 3) the retrieval of stored data more rapidly, completely, and effectively than by manual systems. Profitable utilization of these capabilities is conditioned by several factors, particularly by the information selected for the system data base and by the design of the computer system itself.

Jan 1, 1968

By H. M. Breza

Recovery of phosphate concentrate at Texasgulf’s Aurora Mine has received increased attention as existing mine and plant production capacity limits are reached. Improved mining techniques and mineral processing of waste streams offer the potential to increase phosphate production without major expansion. Innovative processes are being identified to maximize pit mining recovery and to minimize waste stream losses. This results in more effective use of the phosphate. Texasgulf Inc., is a wholly owned subsidiary of Elf Aquitaine. The Aurora phosphate rock mine and refining facilities are located in North Carolina on the south shore of the Pamlico Sound. Phosphate ore is recovered by open- cast mining techniques. Draglines and other earthmoving equipment are used to uncover and mine the phosphate ore. The mined ore then is slurried and pumped about 8 km (5 miles) to the processing plant.

Jan 1, 1994

By Peter C. Ashbrook

The Regional Copper-Nickel Study was initiated in large part because of fears that copper-nickel development might cause adverse effects on the environment from air pollutants such as sulfur dioxide (SOZ) emissions from a smelter, and water pollutants such as acid mine drainage. The Study comprehensively examined the potential for ad- verse effects on the environment and possible mitigation measures on both a local and regional scale by first characterizing existing air and water quality, and existing sources of pollution, and then developing hypothetical development scenarios to model potential adverse effects. This paper gives a brief overview of the Study&apos;s findings concerning air and water resources.

Jan 1, 1980

By J. W. Choung, J. A. Finch

Acid rock drainage (ARD) is a recognized environmental challenge facing mining industries. An ambient temperature ferrite (ATF) process has been investigated for treating ARD. Most nonferrous metal and calcium ions present in typical ARDs were found to be detrimental to the ATF process. Three approaches were examined, including C02 aeration, addition of complex agents and use of magnetic seeds. By introducing magnetic seeds in the ATF process, the interferences were minimized and all the precipitates formed with lime neutralization were magnetically recovered from a simulated ARD. The residual concentrations of major metal ions in the treated water were environmentally acceptable. The XRD pattern confirmed the spinel ferrite crystal structure of the products

Jan 1, 2000

By Clifford J. Lewis

The control of sulfur dioxide and fly ash in the emissions from coal-fired boilers is a significant segment of the national environ- mental protection program. Developing technologies to accomplish this objective presently emphasize aqueous scrubbing techniques. Should circumstances require aqueous scrubbing for fly ash control only, provision must nevertheless be made to counteract the presence of sulfur dioxide which can create an acidic and potentially corrosive environment. Major technologies for sulfur dioxide control by aqueous scrubbing include, l), recovery processes yielding sulfuric acid or elemental sulfur and 2), throw-away processes which produce a sludge consisting essentially of calcium sulfite or varying amounts of calcium sulfate.1/ Recovery processes are more sophisticated and best suited for locations where there are markets for sulfuric acid or sulfur, or where sludge disposal is an overriding consideration. Throw-away processes are generally less sophisticated but have a problem in that gas scrubbing systems may not operate for practical time periods without failures due to corrosion and to plugging by particulates and precipitates. To overcome this difficulty, some throw-away systems employ an aqueous solution of caustic in the gas scrubbing device to assure maximum water solubility of sulfur compounds, followed by the addition of lime to the scrubbing medium in a system external to the scrubber to produce the throw-away sludge and regenerate the caustic for recycle. Such systems are referred to as double alkali systems.2/

Jan 1, 1975

By Michael J. Pratko

The bulk handling industries have long been plagued with problems in their attempt to obtain one of their major goals - the maximum efficiency for which a bulk handling flow system was designed. Mentor Dynamics Ltd. is an international firm with offices in Canada, Japan, and the United States. Mentor Dynamics Ltd. is in the business of solving the "why not" of a system and engineers the solution for the problem. Studies of the varied difficulties encountered with bulk flow systems indicate that 90% of all flow problems fall into one or more of the following categories: abrasion, impact, sticking, and/or inadequate design. These problems can occur with a myriad of bulk solids: coal, gypsum, aragonite, phosphate, fly ash, ore. Solutions to the problems are as varied as the problems. The proper lining material, ceramic, urethane, rubber, and/ or ultra high molecular weight polyethylene, must be coupled with the correct fastening system, annular ring and &apos;F&apos; cap, weld washer, button head fastener, weld studs and/or nuts and bolts.

Jan 1, 1982

By Michael Karmis

The International Conference on Sustainable Development Indicators in the Mineral Industries(SDIMI 2003) was held May 21-23, 2003 on the island of Milos, Greece. The objective of this international conference was to assist the mining and minerals industries in their global transition to sustainable development. The main theme of the conference was the development, monitoring and assessment of sustainable development criteria for mineral operations. Emerging technologies were also presented that can assist in the development of criteria and performance indicators.

Jan 1, 2003

By J. J. Pavlica

Grinding in steel mills adversely affects the flotation removal of pyrrhotite from magnetite ores. To elucidate the effect of grinding media on the floatability of pyrrhotite, rest potential and short-circuit current measurements were made on electrode combinations of pyrrhotite-mild steel and pyrrhotite-stainless steel. Galvanic contact of pyrrhotite with mild steel increased the rate of surface reactions on pyrrhotite in air-exposed and oxygenated solutions. It was postulated that the formation of &apos; an iron hydroxide coating on the pyrrhotite adversely affected its floatability. Its formation was minimal when pyrrhotite was contacted with stainless steel. Fine magnetite particles caused slime coating on pyrrhotite surfaces by magnetic interaction and impaired the flotation of pyrrhotite.

Jan 1, 1982

By S. Lin, Y. J. Wang

Through an example three fan ventilation network concepts of subsystem solution and characteristic curves of a multiple fan ventilation system are introduced. The major steps of defining a subsystem, working out the subsystem equations, constructing a solution curve and a characteristic curve, and determining the operating points of the reference fan and the ventilation system are systematically demonstrated through three and two-dimensional curves. Also briefly discussed are the main features of a subsystem characteristic curve.

Jan 1, 1993

By Gordon T. Clark, Stephen H. Gleaton

This paper discusses the conceptual design of cut-and-cover tunnels currently being considered as one of the replacement options for the earthquake damaged, elevated double-deck highway and seawall built in downtown Seattle 50 years ago. The 4.8 km (3 mile) long, 6-lane improvement consists of 1.6 km (1 mile) of at-grade roadway with aerial interchanges, 1.6 km (1 mile) of large two-level cut-and-cover tunnels along the Elliott Bay waterfront, and retrofit of the 50-year old, 1.6 km (1 mile)long Battery Street tunnel and north transition to grade. Construction of deep cut-and-cover tunnels, in complex glacial geology overlain by hydraulically placed fill immediately adjacent the existing sea wall, will require extensive use of concrete diaphragm walls, ground improvement and dewatering. The potential liquefaction and lateral spreading of the fill materials in this active seismic region pose significant design challenges and risk.

Jan 1, 2003

"The Mine Haul Road Optimization Alliance is an Australian industry-academia collaboration which has been developed to support mine haul road operators by fully integrating mine road design research solutions with industry end-user service providers to design, assess, implement and monitor the various equipment, materials and road management strategies required to optimize the safety, environmental and economic performance of a haul road. Initially, a broad overview of the university-industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis, internationally. This insight places realization of a collaboration between Curtin University Western Australian School of Mines Mining Engineering and Metallurgical Engineering (WASM ME2) and the Haul Road Optimization Alliance (HROA) industry members into context of opportunity. Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry can collaborate to deliver a more robust solution to mine haul road design, performance or management needs, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service-providers alike forms the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and implementable solutions. The paper concludes with examples of how the alliance collaborations work in practice to deliver improved mine haul road designs and optimized operational performance, together with the mechanisms used to ensure industry needs are met through focused, end-user driven research and integrated solutions implementation."

Jan 1, 2016

The problems of toxic, noxious, and explo¬sive atmospheres caused by gases and dusts are certain special environmental considerations in underground mining. Some other problems unique to underground mining are design of stable structures in the strata and their support, lighting the workings, and control of noise in confined spaces. These affect the health and safety of the workmen and deserve critical analyses. Some of the most important environmental parameters of underground mining are summarized in Table 1. The list is not exhaustive but illustrates the scope of environmental planning in underground mining. This chapter will discuss the use of computers and computer models in mine atmospheric environmental planning.

Jan 1, 1979

By M. Misra

The processing strategy for the effective separation of bitumen from low grade (< 10 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1979

By Don C. White

Santa Rosa is a mid-Tertiary, volcanic-hosted, gold-silver deposit. Current proven and probable reserves are 8.9 Mt (9.8 million st) grading 1.5 g/t (0.044 oz/ st) gold, minable by open pit and amenable to heap leaching. It is the product of hydrothermal mineralization along an arcuate segment of a caldera collapse ring fault in a probable maar volcanic setting. This segment was later broken by radial faults. Gold at Santa Rosa occurs principally as electrum, finely disseminated through intermediate tuffs, and associated with pyrite. The nearby Alto de la Mina deposit displays stockwork silica-pyrite-gold in a tectonically and hydrothermally shattered andesite flow. Miocene epithermal mineralization was accompanied by central silicification and pyritization and more distal argillization. An andesite flow cap rock at Santa Rosa played a pivotal role as an upward permeability barrier. Highest gold grades and most intense alteration occur closest to the ring faults and immediately beneath the andesite flow. Supergene alteration effects on the gold distribution are minimal.

Jan 1, 1995