Search Documents

By C. P. Boddy

One of the most difficult tasks a project manager will have in pre-mine planning is dealing with the mine site's hydrologic regime. Numerous federal statutes passed by Congress in the last decade have made the coal mining industry more responsive to the environmental impact during all phases of the mining process. Permitting these mines has dictated a cradle to grave approach in dealing with water related issues. This paper will attempt to explore the application of these technology- based laws and their direct application to the unique environment found in Alaska's interior regions.

Jan 1, 1985

By Timothy C. Richmond

The Stillwater District is located in south central Montana approximately 75 miles southwest of Billings, the state's largest city. It lies along the northeast front of the Beartooth Mountains and is within the boundaries of the Custer and Gelatin National Forests. The district contains some of the nation's most spectacular mountain scenery. Montana's highest peaks, including 12,799 foot Granite Peak, rise a few miles south of the area. Much of the district is located on a gently undulating plateau which averages 8500 ft. above sea level, broken by hills up to 10,000 feet and slashed by glacially carved canyons, some of which are more than 3,000 feet deep.(Fig. 1) Immediately to the north and east, the land falls away to the Great Plains, stretching unbroken to the Mississippi River. Two major tributaries of the Yellowstone River, the Stillwater and Boulder Rivers, traverse the area and several large streams originate in the district itself. Access to the high mountain country and the adjoining Beartooth Primitive Area is restricted to a few horse and jeep trails continuing from the terminus of improved roads in the bottom of the Stillwater and Boulder Valleys. Hunters, fishermen and cabin owners make intensive use of the area along its improved transportation routes, but hikers seldom venture more than three miles beyond the end of the roads. People from the Billings area are the most frequent visitors.

Jan 1, 1974

By Gary L. Simmons

Noranda's Grey Eagle Mine and Mill, located in the Siskiyou Mountains of Northern California, began shakedown operations in the late fall and early winter of 1982. This paper describes some of the unique features in mining, milling and water treatment operation at Grey Eagle. In addition, major start-up problems in the mill and water treatment plant are discussed along with measures taken to correct these problems.

Jan 1, 1984

By Nathaniel Arbiter, Robert R. Beebe

The U.S. mining industry - once world dominant and largely independent of foreign sources for most major commodities - has today lost this position, with little likelihood of regaining it. But even though Business foretold The Death of Mining four years ago, the current outlook is less pessimistic because of drastic restructuring of the industry; a major reduction in its labor force, with resulting large increases in productivity; and introduction of improved technology. In the face of this clearly changed climate for domestic mining, it is important to examine the role of the development and research establishment in the industry's future, which raises a complex set of questions: 1. Where and to what extent can new technology assist in the continued survival of the industry ? 2. What is the past record of the research establishment in developing new technology; and what is the industry's record in supporting and adopting it ? 3. In the light of these records, and of the drastic cuts in both research staffs and expenditures, what areas should be the most important targets for new technology? New Technology vs. Old A1 though mineral processing's origins can be traced back through five or six millennia, its modern structure is about 200 years old.

Jan 1, 1989

By J. J. Casey

This paper is one of a series of presentations organized by the Conference of American Society of Civil Engineers with the goal of making significant progress toward an equitable and effective allocation of risks in construction undertakings among the principal parties - owner, contractor and designer. The role I have been assigned is principally one of identification of risk while others will devote greater attention to the allocation of these risks and the contractual arrangements necessary to properly make these allocations. Construction projects are joint undertakings by parties who bring different skills and interests toward a common effort, much as this conference does. A project is not an adversary proceeding and does not benefit from establishment of an adversary mode, as our lawyer friends seek in the resolution of legal issues. Accordingly, I urge upon this Conference the adoption of two basic precepts and guidelines as the criteria for sharing of the risks inherent in construction undertakings toward achievement through mutual effort the common goal of a successful project completed in the shortest time and at the least overall cost. These precepts are: (1) that all risks are rightfully the owners unless transferred to or assumed by another party for a fair compensation; and (2) that the principle guideline in determining whether a risk should be so transferred should be whether the receiving party has both the competence to fairly assess the risk and the expertise necessary to control or minimize it. The sponsors of the conference have provided certain guidelines to the authors. There is, however, no constraint in expressing one's bias and I suspect that my contractor's outlook may be inherent in my comments. The guidelines have suggested that I indicate whether the risks identified are ones that can or should be shared or borne by one party alone. In doing so, I will attempt to follow the precepts I have recommended.

Jan 1, 1979

By N. B. Aughenbaugh

The People's Republic of China has 582 Gt (641 billion tons) of proven coal reserves. At present, 576.5 Mt (635.5 million tons) of coal are mined a year which makes China the third largest producer of coal in the world. Underground mining accounts for 95% of the total production. This paper will discuss the coal districts, coal types, jurisdiction of coal mining, and methods of underground mining. The article also will outline China's objectives in future planning and development of its coal reserves.

Jan 1, 1982

By Roger D. Sharpe

Oklahoma contains extensive resources of high-purity gypsum that were deposited in the Anadarko and Hollis basins during Permian time. The gypsum resources and reserves are estimated to be about 48 billion short tons and a; located in the western portion of the state. Oklahoma is the largest producer of gypsum products in the United States. The Blaine Formation and the Cloud Chief Gypsum contain several beds of minable thickness. Four stratigraphic units in the Blaine Formation are quarried in Oklahoma. The Shimer, Nescatunga, and Medicine Lodge Members are quarried in northwest Oklahoma. The Van Vacter Member, consisting of three gypsum beds, is quarried in southwest Oklahoma. The Cloud Chief Gypsum is quarried in the west-central part of the state. The gently dipping gypsum in the Blaine Formation generally crops out along low escarpments and is covered in the downdip direction by increasing overburden, consisting of sand, shale, and/or dolomite. Anhydrite occurs in the downdip direction under the thicker overburden. The Cloud Chief Gypsum crops out as hills, which are eroded remnants of a more widespread, massive sulfate unit. All of the gypsum produced in Oklahoma is extracted using quarrying methods. A variety of products are made from gypsum quarried in Oklahoma. The products are manufactured from uncalcined, calcined, and deadburned gypsum. Products vary from raw, ground gypsum used for agriculture, to high-value-added industrial plasters, cements, and fillers produced from calcined gypsum. A sampling of the many products manufactured from Oklahoma gypsumincludes: (1) agricultural-soil amendment; carrier for insecticides, pesticides, and herbicides; calcium supplement in animal feeds; (2) gypsum wallboard-common, fire-resistant, and water-resistant varieties; (3) industrialgypsum plasters-art and casting, pottery and ceramic, molding and tooling, crayons, wall patching; (4) industrial gypsum cements-oil-well cement, high-strength statuary, high-strength tooling, fiber-reinforced architectural, road and bridge repair; (5) food and pharmaceutical-filler and binder in aspirin and other medicines, yeast activator in brewing of beer, moisture absorbent in bread and pizza dough; and (6)portland-cement retarder-ground with clinker to control setting time.

Jan 1, 1999

By Joe M. Short

More than eighty years ago, in what we generally consider a more leisurely age, workers and engineers began the construction of the longest railroad tunnel in the world. When completed, the Simplon Tunnel ran more than twelve miles through the alps to connect Switzerland and Italy. Work began in 1898 and the tunnel was completed in 1905. In all it took about seven years to build one of the world's great tunnels. More than seven years ago, in what was hoped to be a rapid and constructive to the deaths of 38 workers in two spectacular tunnel disasters in 1971, the secretary of Labor's Construction Advisory Committee on Safety and Health began in January 1972 a search for an effective standard on tunnel safety. Much hard and useful work has been done, especially by the construction advisory committee' but more than seven years later, we still don't have a tunnel standard. We may speculate that, when the Simplon Tunnel was completed, workers and their bosses assembled to celebrate their achievement and to count their casualities. We have no need to speculate on the lack of achievement up to this time. An so far as I know, the bureaucrats have suffered no casualities except perhaps some unreported cases of ring-around-the-color. The only moral I can draw from all this is thai it is easier to penetrate solid rock than it is to get through bureaucratic fog. We can only hope that OSHA will finally take advantage of the work which was finished years ago and complete the actions necessary to give us a tunnel standard. Having made my point, I could stop my remarks right now; but

Jan 1, 1979

By T. E. Breaux

Repair of large rotating apparatus such as ball mills is uncommon but under certain circumstances is achievable. This paper describes the successful repair of trunion on a 14 foot diameter by 20 foot long ball mill. Diagrams of the repair are included for visual perspective and non-destructive test procedures are outlined.

Jan 1, 1988

By Thomas R. Kuesel

Just south of the L'Enfant Station in Seventh Street, the WMATA system splits into two branches, each comprising twin single-track soft ground tunnels. Immediately at the beginning of the section, Interstate Route 95 crosses transversely over the alignment in open cut, removing most of the cover over the tunnels. Seventh Street spans I-95 on a bridge whose abutments and pier also cross transversely over the four tunnels, with their footings as little as 7 feet above the tunnel crown (Figure 1). Soil investigations revealed that the tunnels would have to be driven through mixed face, with a clay invert and a waterlogged sand crown. Thus, there was a good chance that the roof would fall in, leaving 1-95 and the Seventh Street Bridge in a crater. Since there was no roof that could be counted on, these were figuratively (and potentially truly) Washington Metro's Topless Tunnels (Figures 2 and 3). DESIGN ALTERNATIVES Faced with this situation, the designers considered several options, including temporary detours that would permit demolition of the bridge and building tunnels under the 1-95 Freeway by cut-and-cover methods. They also investigated structural underpinning of the bridge and freeway pavement, and strengthening the bridge abutments and center pier by post-tensioning to enable them to span over any subsidence trough.

Jan 1, 1976

By V. R. Bovino

In the early 80's, the cover of a major weekly magazine proclaimed the "Death of Mining." A few years ago, mining conventions, similar to this, around the country sported the theme, "The Survival of Mining." Today, the SME announces that "Mining is Alive." Being part of an industry that is simply alive is not very exciting. We can do better! Our challenge must be to flourish, blossom, maximize our potential and expand our horizons. The pace of rejuvenating this industry is still woefully inadequate. The new generation of mining industry leaders recognizes the urgent need for bold operational changes?changes in the way we deal with our employees? changes in the way we achieve productivity? and changes in the way we reward our employees for productivity.

Jan 1, 1991

By Terry B. Linde, William M. Dowall

The recently completed In-Pit Crushing and Conveying Project at Phelps Dodge's Morenci Mine is rated among the world's leading materials handling projects. The operation involves the crushing and transport of more than 109,000 tonnes per day of copper ore, utilizing regenerative conveyors capable of providing over 5.5 megawatts (7,000 hp) of equivalent electrical energy. This paper describes the key aspects of the project and includes: Original project objectives; System design criteria; System description; Optimization studies; Major design features; Equipment description; and System commissioning.

Jan 1, 1993

By Grant R. Brown

The purpose of this opening paper is to provide an overview of incentives strategies. This overview includes a discussion of the different types of incentives, their advantages and disadvantages and their potential application to the mining setting. Objective The primary objectives of incentive plans are to increase worker (including management) effectiveness and reduce unit labor costs. These plans can be grouped into two major categories: 1) non-financial plans 2) financial plans

Jan 1, 1983

By W. Rocher

The Minera Ojos Del Salado (?MINOSAL?) concentrator is located 20 kilometers southeast of Copiapo, Chile and processes copper ore provided by its Santos and Resguardo mines at a capacity of 4,200 tip (4,620 stpd). Phelps Dodge acquired the majority interest in MINOSAL in 1982. The principal incentive for this purchase was the exploration potential of the property. At that time, the concentrator plant was a small, antiquated installation with a capacity of 674 t/d (740 stpd). In 1982, the majority of the ore was produced from the Santos and Resguardo mines, but custom ores of copper, silver, and gold were also treated. The acquisition occurred at a crucial time in the copper business, since the price had fallen to nearly $0.50 per pound. In 1985, Phelps Dodge purchased the outstanding interest in MINOSAL and acquired 100% of the property. Today, after numerous improvements and two expansion projects, the concentrator is an interesting combination of old and new equipment. The regrind mills, for example, have been in service for about 50 years, while the ceramic concentrate filter represents the latest technology.

Jan 1, 1993

By B. A. Hancock

New permit discharge standards instituted at Hecla Limited?s Lucky Friday Mine required installation of water treatment plants to manage water quality at two outfalls to the South Fork of the Coeur d?Alene River. The 002 Outfall Water Treatment Plant (WTP) is a clarification-filtration plant for treating the combined mill and underground discharge water flows. Process optimization efforts were a significant challenge until the negative impact the exploration diamond drilling products had on the clarification process was identified and resolved. The products were being wasted directly to the mine water discharge system which was pumped to the surface WTP. Anionic soluble oil and polyacrylamide based products were causing TSS particle hydrophobicity and dispersion that greatly affected coagulation and flocculation response, resulting in excessive chemical usage and treatment control issues. This paper details how problems associated with the drill products negatively impacted the 002 WTP and how system changes, alternative product usage and treatment at the source resulted in more consistent plant performance.

Jan 1, 2011

By G. Bourque

Early in the design stage of their new concentrator for the Mount Wright Plant, Quebec Cartier Mining decided to use a process computer for total control of crushing, grinding and concentrating. A map of the area is given in figure 1 and a view of the plant in figure 2. Although the use of process computers is not a new idea in petrochemical and chemical industries, their use in the mining industry is very limited. We innovated in using the computer, not only for data logging, as we have seen in some other plants, but a sole operator located in the administration building, starts and stops mill lines, crushers, load-out system, tailings, thickeners, etc ... by means of a CRT console. Our process is fairly simple as can be seen on the schematic process flow diagram (figure 3). .The ore, carried by 136t diesel electric trucks, is dumped through ore pockets onto two primary pan feeders. The feeders supply two 1,52mx2,79m gyratory crushers which reduce the ore to minus 20,32 cm. Each crushing line have a capacity of 5600t per hour and feed a shuttle conveyor distributing the crude ore into six silos.

Jan 1, 1979

By Henry F. McCabe

The principals of McCabe Industrial Minerals, Inc., have been involved in the mining, processing, and marketing of nonmetallic minerals for more than 40 years. In addition to marketing nonmetallic minerals produced by other companies, McCabe Minerals owns and operates three plants that produce headlap-roofing granules, with 25 employees and annual sales approaching $6 million. During its 22 years of operation, the company has developed many different markets, and a list of factors that is used in making our marketing and feasibility studies. These criteria (Table 1) are used extensively by the company in all of its projects, and we present this and other data about the company in this brief report. HISTORY OF THE COMPANY A brief outline of the history of McCabe Industrial Minerals follows: I. McCabe Industrial Minerals, Inc. (Formerly McCabe-Woody & Co.). A. Founders: 1. Henry F. McCabe (experience): a. Heart of Texas Sand Co., Brady, Texas (1959-67) b. Delta Mining, Mill Creek, Oklahoma (1967-76) 2. A. H. Woody (experience): a. Heart of Texas Sand Co., Brady, Texas (1961-65) b. Featherlite Corp.-Light-weight aggregate

Jan 1, 1999

By John A. Organiscak

The Bureau of Mines evaluated a new dust control technique for longwall personnel required to work at the tailgate end of the face. This technique utilizes a water-powered scrubber to clean a portion of the face air, which is discharged behind a brattice partition at the working area. Laboratory simulation of this system in a wind tunnel resulted in average efficiencies greater than 70 pct with system efficiency directly related to scrubber quantity. Underground evaluations indicated a similar direct relationship between scrubber quantity and system efficiency. Gravimetric measurements of respirable dust made during these underground evaluations resulted in average protection efficiencies ranging from 30.7 to 42.5 pct with increasing scrubber air quantity.

Jan 1, 1983

By R. S. Jurani

Sunshine Mining Company's Kellogg operation is the primary silver producer in the United States, and maintaining a comfortable working environment in this deep underground mine historically has been a complex and costly problem. To improve the ventilation and cooling systems at a time of declining and uncertain silver market, it was proposed to optimize the performance of existing facilities at minimum cost. This paper discusses a 2-year, $400 000 optimization program that resulted in increased total mine airflow, cooler ambient temperatures, reduced compressed air usage, and lower energy consumption by primary fans, air compressors, and refrigeration plants, thereby saving the company approximately $650 000 per year.

Jan 1, 1987

By Theodore S. Jordan

The discovery of a major porphyry-type copper deposit on the Papago Indian Reservation in Pinal County, Arizona was announced by El Paso Natural Gas Company in 1968. The deposit, known as the Lakeshore Property, contained an estimated 470 million tons of sulfides and oxides averaging 0.75 percent copper. History and Geology of the area have been described by Harper and Reynolds (1969). El Paso subsequently&apos; entered into the agreement for joint development of the property with Hecla Mining Company, with Hecla as the operator. The ore body consisted of three types of mineralization: 1) Disseminated Oxide Ore, <1% Cu 2) Disseminated Sulfide Ore, <1% Cu 3) Tactite Ore, >1% Cu

Jan 1, 1985