Search Documents

By W. C. Baver

Even before the energy crisis developed in the early '70's, considerable research world-wide was being directed towards the development of schemes to both reduce the energy requirements and to reduce air pollution emissions associated with the manufacture of glass. In many cases the sought-for solutions would benefit both objectives. If, for example, the glass batch could be consolidated into such compact forms as briquettes or pellets, they could be preheated in a moving-bed heat exchanger with the high-temperature exhaust gases from the glass furnace. Lower furnace temperatures would thus be possible with a corresponding reduction in heat losses and total fuel consumption. Moreover, the lower temperatures would also reduce the amount of nitrogen oxides generated in the furnace and emitted to the atmosphere. Many tests on consolidated glass batch have been run in many countries. In some cases, extended tests on production furnaces have also been included in the programs. For various reasons, however, none of these has proved to be economically attractive. The current, but temporary lull in the rapidly rising cost of energy which has been with us in recent years, has reduced the push for research for energy saving means for melting glass. A few of the current programs will be discussed. Since raw material requirements, primarily physical in nature, are affected by some of these schemes, these will also be considered.

Jan 1, 1986

By Russell Clough

The Pacheco Pumping Plant is situated on the west end of San Luis Reservoir in western Merced County, California. It is designed to draw water from the reservoir and pump it into a 3,500,000 gallon regulating tank. The water then flows entirely by gravity to the Coyote Pump Station in Morgan Hill, a distance of 40 miles, where it is pumped into Anderson Reservoir. This water is used to recharge the depleted groundwater table in the Santa Clara Valley. Eventually, some of the water will be diverted to Hollister in San Benito County and to Watsonville and Santa Cruz in Santa Cruz County. The owner is the United States Bureau of Reclamation. The underground work consisted of a fifteen foot finished diameter surge shaft 250 feet deep to the crown of the pump chamber; a twenty foot finished diameter pump chamber which declined from the shaft at 14.2% for ninety feet and then ran horizontally for 180 feet; and twelve each five foot diameter steel lined intake shafts 240 feet deep which intersect the pump chamber in the horizontal section. (Figure 1) Upon completion of the pump chamber, the contractor had to dewater the existing tunnel under the reservoir, excavate the remaining fifteen foot plug, and concrete the transition. The low bidder for this contract was Underground - Continental-Heller at 414,456,000. Excavation of the open cut for the pumping plant and surge shaft began on April 14, 1983. This was performed using a Koehring 1066D backhoe, dozer, trucks, and two Cat 631 scrapers. The excavation was started at the surge shaft so that the grouting could begin

Jan 1, 1985

By George E. Summers

A salt dome appears to provide the basic medium requirements for the excavation of the 315 foot diameter, unsupported spherical cavity at a depth of 2700 feet required by the AEC in a proposed "decoupling" experiment. Tatum Salt Dome was a natural choice for a site because more geological and hydrological information has been accumulated on Tatum than any other salt dome on the Gulf Coast. The Tatum Dome is a mile in diameter, roughly flat topped, nearly cylindrical in shape and has some overhang at the top. The salt stock has nearly vertical layering of alternating bands of salt and anhydrite. In the vicinity of the dome, adequate fresh water for solution mining is available in surface streams and in subsurface aquifers. A saline aquifer is available for brine disposal. A tentative cavity location was selected near the center of the dome which meets the design criteria established by the AEC.

Jan 1, 1968

By Ronald B. DeDiemar

It is generally held that cone crusher application technology is strictly an art and thus subject to the vagaries of emphirical and/or trial and error judgments. While this is basically true, certain factors have been identified which, when properly defined, can significantly reduce the element of chance. This paper will bring out these factors as well as pointing out other technologies available to predict and/or analyze cone crusher performance.

Jan 1, 1977

In longwall mining, premining prediction of methane emission rate depends on a number of geological factors, geographical factors, and operational factors. These same factors also can impact the selection of a specific degasification system. This study proposes a principle component analysis (PCA) and artificial neural network (ANN) approach to predict the ventilation methane emission rates of U.S. longwall mines and the optimum combination of degasification boreholes based on the given characteristics of the mine. Artificial neural networks, more than conventional computer models, are adaptable systems that can solve problems such as non-polynomial or very complex relationships that are difficult to describe mathematically. Data on ventilation emissions and degasification system design were obtained from 63 longwall mines in 10 states and were combined with corresponding geological, geographical, and operational parameters for the period 1985-2005. PCA was used to determine the variables that most influence ventilation emissions and degasification system design. Different combinations of variables in the data set and network structures were used for network training, cross-validation, and testing. The resultant ANN models predicted ventilation methane emissions with a 90-95% accuracy and were superior to multi-linear and second order non-linear models. The ANN-based expert classification system was able to classify the design of the degasification system (no degasification, gob vent borehole, horizontal and gob vent borehole, and horizontal, vertical and gob vent borehole) with more than 80% accuracy. The models can be used as prediction and decision tools for the ventilation emissions and degasification system selection for specific site and mine-design conditions.

Jan 1, 2009

By L. E. Krys, K. D. Harrison, C. G. Anderson

Since 1984, nitrogen-species catalyzed pressure leaching has been utilized at Sunshine Mining and Refining Company for the recovery of precious metals from a refractory sulfide concentrate. The process operates without the use of cyanide. The plant is now the only industrial-scale commercial application of this technology. Since the inception of the process, changes have been implemented to improve efficiencies and throughputs. Two of these changes, the replacement of nitric acid by sodium nitrite and a concentrate regrind, have recently been implemented. This paper discusses the development and potential mechanisms involved in these recently patented plant-process changes. A companion publication (Anderson et al., 1996) covers the plant integration and potential applicability of the technology.

Jan 1, 1997

A roof rating system has been devel¬oped for upper seam damage prediction during mul¬ti-seam mining based on structural and geologic conditions in the upper seam. Two primary consid¬erations -geologic and spatial - form the basis of the classification system. It includes factors commonly found in geomechanics classification systems as well as factors which are peculiar to multi-seam mining, such as those which define the two adjacent seams and the innerburden. This rating system has been applied to numerous case studies to form empirical relationships for quan-titatively predicting potential upper seam damage based on anticipated subsidence and strain values and vertical movements.

Jan 1, 1988

By M. Soderstrom

In a solvent extraction (SX) plant, stage efficiency calculations are used to determine mixer efficiency. With modern extractants and mixing equipment, it is generally taken for granted that stage efficiencies will be above 95%, but this is not always the case. Dependant on mixer/solution conditions, stage efficiencies can occasionally be low, therefore leading to higher reagent usage. Proper methods to identify when stage efficiency performance is below expectations, and ways to identify if it is an equipment or chemical issue are valuable tools for a plant metallurgist. With these tools and skills an on-site metallurgist can more quickly return their SX plant to proper operation. This paper will discuss methods for analyzing stage efficiency, evaluating factors that may affect stage efficiency, and evaluating the impact of stage efficiency on the overall operation.

Jan 1, 2010

By S. Srinivasan

Traditional pit optimization techniques cannot take account of the requirement to blend ore in order to produce a saleable product, as is the case for iron ore, coal, limestone and other industrial minerals. Various techniques are proposed to overcome the deficiencies, many of which have been tested. The techniques in general involve the combined application of pit optimization and blend optimization techniques.

Jan 1, 1996

By James R. Evans

Orange County, adjacent to the populous and industrialized Los Angeles area, is the fastest growing county in California and is second only to Los Angeles County in total population (figure 1). In addition to an equable climate and a burgeoning economy, there is room in Orange County for growth and expansion. Growth over the past decade has resulted in rapid development of industrial tracts, housing areas, and shopping and commercial centers, mostly in former agricultural areas. The value of new building in 1972 was a record amount-over I billion dollars (figure 2). Problems relating to the proper direction of growth are the concern of both government and the private sector. The intelligent and efficient use of areas to be developed requires planning for the conservation and protection of the County's natural beauty and for the orderly development of natural resources. The availability of sand and gravel, which is used in many phases of construction, will be a major controlling factor in the future of the County.

Jan 1, 1974

By Joe Scheuering, Don Poulter, John Trirnble

Closure of the Grey Eagle Mine tailings impoundment is an example of closing a "wet" tailings impoundment at the cessation of milling operations. This paper presents a summary of tailings cover design and construction, tailings deposition sequences to facilitate closure, construction schedules, costs, and post-closure monitoring. Permit requirements which influenced the design and construction of the tailings are summarized. The performance of the cover and post-closure monitoring issues are also discussed.

Jan 1, 1995

By Ronald E. Yarbrough

As a result of concern for the citizens of the State of Illinois who owned structures above underground mine workings, the Illinois State Legislature passed House Bill 158 in 1978. This bill amends the Illinois lnsurance Code and creates the Mine Subsidence Reinsurance Fund which is an insurance pool that is to receive a state appropriation of $500,000 as "start-up" money. One hundred thousand dollars has been paid to the fund as of October, 1982. The Fund is to return this appropriation to the State and is to remain self-supporting from premiums. The Fund utilized a pre-existing institution, which also was an insurance pool, the "Fair Plan Facility" and its governing Board, consisting primarily of insurance executives, to administer the program. The Mine Subsidence lnsurance Act went into effect October 1, 1979, and the bill provides that property owners in the State of Illinois may purchase up to $50,000 of mine subsidence insurance which is attached to their fire insurance policy. The deductible is normally 2%, but cannot be less than $250 or more than $500. The annual rate structure for residential structures in 1981 for $50,000 coverage is $10 (frame), and $12 (masonry). The rate structure for commercial buildings is based on the value of the building and the rates for $50,000 maximum coverage is adjusted upward. The insurance was mandated by the State Department of lnsurance and rolled onto the insurance policies of the homeowners in 34 counties which had been recognized as having sufficient exposure to subsidence damage to be covered by the Act. One percent or more of the land surface is undermined in each of the 34 counties. In the other counties undermined in the State of Illinois, insurance is available to the homeowner upon request to the private insurance carrier.

Jan 1, 1982

By Ross R. Bhappu

In 1989, William A. Vogely created the Mineral Economics and Management Society (MEMS). He did this after SME disbanded the Minerals Resource Management Committee, a group dedicated to technical programming of minerals economics and management issues. A few years later, SME reinstated this committee. MEMS held its fourth annual conference "Mineral resources: Managing dilemmas and opportunities," in Boulder, CO March 9-11, 1995. Some of the MEMS programs are similar to the Minerals Resource Management Committee programs. However, MEMS conferences cover more diverse issues. These include minerals policy, environmental legislation impacts on the minerals industry and minerals economics issues. The 1995 MEMS conference included six sessions and three distinguished speaker addresses. Papers topics included US and Canadian mineral policy, financial strategies for managing mining companies, Latin American mineral investment opportunities, quantitative economic modeling and the impact of environmental interest groups on the minerals sector in the United States and Canada. One session was dedicated to students who competed for $1900 in prizes for outstanding papers.

Jan 1, 1995

By R. J. Roman

Several research groups have spent considerable time investigating coarse ore leaching. Coarse ore leaching includes both heap and dump leaching. The term "heap leaching" will be used in this paper to mean any type of coarse ore leaching. The results of their work are generally in agreement: the progress of leaching can be described by the shrinking core model and its associated mathematics. The shrinking core model is schematically represented in Figure 1. The particle is contacted by the leach solution on its outside surface and the solution migrates inward by filling the pores on the particle. As the solution filling the pores comes in contact with grains of ore mineral the reagent chemically reacts with the ore mineral to solubilize the contained metal. The solubilized metal diffuses outward to the particle surface and is washed away by the leach solution flowing past the particle. The leaching reagent in the particle interior is replenished by the diffusion of reagent from the surface of the particle to the interior of the particle. If the chemical reaction between the leaching reagent and the ore mineral is relatively fast compared to the diffusion rate of the reagent in the solution in the pores of the particle then leaching proceeds from the outside of the particle inward resulting in a "shrinking core" of unreacted ore surrounded by a "leached shell". The rate controlling step in the reaction can initially be a chemical reaction between the reagent and the ore mineral grain, however, once the reaction has proceeded a short period of time diffusion of the leaching reagent through the leached shell will be the slow step and hence the rate controlling step in the production of metal from an ore particle.

Jan 1, 1992

By D. R. Wilburn

his summary of international mineral exploration activities for the year 2011 draws upon available information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents [ ] analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia; 2) regional and site-specific exploration activities that took place in 2011 as compiled by the USGS and 3) regional events including economic, social and political conditions that affected exploration activities, which were derived from published sources and unpublished discussions with USGS and industry specialists.

Jan 1, 2012

By B. Cavender

Mining managers trying to rapidly reduce production costs tend to implement a traditional set of topdown managerial practices: reductions in production volume, employee layoffs, renegotiation of supplier contracts, cancellation of employee training, restrictions on travel, reductions in office supplies, and so forth. While these practices do reduce costs, the benefits are often limited in both magnitude and duration, and the workforce is usually left demoralized. Successful cost-cutters take a different approach. They make the continuous reduction of costs a priority for all members of the organization, whether managers or workers. The culture of these firms emphasizes the commitment, voluntarily given, of individuals and work groups to this goal. Cost-cutting practices often reject all of the traditional methods mentioned above, but are far more numerous, innovative and successful. This culture of cost reduction is the result of a set of leadership competencies that establish direction for the organization, align the organization's various constituencies with this direction, and motivate and inspire the organization. Cost reduction then becomes a routine task rather than a heroic achievement.

Jan 1, 2002

By Stanley Dempsey

Since its passage, the Mining Law of 1872 has been modified several times to meet the changing needs of America's society and economy. Despite the fact that it continues to provide an effective framework for a robust US exploration and mining industry, the mining law continues to be criticized in some quarters as outdated. Pressure to reform the Mining Law of 1872 has reached new levels in recent years. Many proposals for reform of the law have been introduced during the 1990s. None, though, have been enacted. The issue will not likely disappear and is certain to be raised during the 105th Congress. To provide a better understanding of the status of current congressional reform proposals, this article presents an overview of the major moments in the history of mining laws in the western United States - from the days before the 1872 mining law and the days following its promulgation, to the current dilemma over mining law reform. The future of the mining law is assessed as are the interests at stake for the modern mining industry. Mining before 1872 No discussion of the Mining Law of 1872 is complete without some historical background to provide an understanding of the origins of this unique law. There was plenty of mining activity on the public lands before the mining law was enacted. At first, the federal government's policy was to allow all miners to work freely on the public lands and to resolve disputes among themselves. In this "hands off" environment, miners operated according to laws they promulgated. These were based on previous experiences in Europe and Mexico. These "frontier codes" of groups of individual miners took the form

Jan 1, 1997

By K. W. Grubaugh

The recently enacted federal surface mine law (P.L. 95-87) will increase further the complexity of securing a reclamation permit. This law intensifies the need to present the required reclamation plan in a thorough and comprehensive manner. One plan format, that used in construction performance contracts, offers promise of filling this need. Reasons for using the format of expressed, bilateral, negotiated contracts common to the contruction industry, and the salient aspects of an application which uses this format are reviewed. Advantages of this procedure are seen to be improved mine planning, awareness of the total design job, potential for improved speed of permit acceptance and improved cost control.

Jan 1, 1978

By G. Deschênes

In an earlier study (Deschênes et al., 2009), gold and silver were shown to be efficiently extracted from samples taken from the Kupol Mine in Russia using lead nitrate in a cyanide leach system. In the current study, a com-parison of the technical and economic merits of a new technology called CANMET enhanced leaching process (CELP) was made with the cyanidation/acidification-volatilization-recycling (AVR) process using eight metal-lurgical variability samples, as well as a large composite sample, which was to represent the initial two years of Kupol mill feed. The composite sample leach feed assayed 33.4 g/t Au and 289 g/t Ag. The metallurgical results from the large composite sample demonstrated that CELP produced very similar gold and slightly higher silver leach extractions compared to the conventional cyanidation/AVR leach conditions at 1/2 the cyanide concentra-tion (1,000 ppm NaCN in CELP vs. 2,000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton was approximately the same for the two technologies (total cost of CELP with the use of Merrill-Crowe at $46.48/t, with cyanidation/AVR at $46.13/t). However, the implementation of CELP would eliminate a capital expenditure of approximately $5 million for an AVR system based on a 2005 feasibility level cost estimate. Eight variability samples used to confirm the composite sample results showed that, on average, the gold leach extractions with CELP and the conventional leach conditions were very similar, but the average silver leach extraction was 2.1% higher for CELP. Furthermore, CELP silver leach extraction was 4.6% higher on average compared to conventional cyanidation for the four mid-grade variability samples evaluated. The decision was made to remove AVR cyanide recovery from the flowsheet and implement CELP at Kupol. The ability to use the conventional leach equipment with CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2010

By K. C. Jordi

Many systems which are modelled mathematically result in a model where the relationships between some or all of the parameters are found to be non-linear. These systems are usually complicated further by a desire to make the system achieve multiple and often conflicting objectives or goals simultaneously. Rozwadowski (1970) developed a model to describe the total discounted net profit of a mine as a function of the amount of ore developed and of the grade of the amount of ore mined. Dynamic programming was used to determine the policy which gave the maximum net present value. In this paper it is shown that the relationships between the variables can be approximated by piecewise linear functions. This is amenable to solution by an algorithm based on the simplex algorithm of linear programming. The goals of maximizing the net present value, the total net profit and the total gold output are incorporated simultaneously into a goal programming formulation of the system. The resulting model is characterized by a large number of disconnected constraints. These are decomposed into several smaller problems and the problem solved. The solution is examined to discover the sensitivity of the system to changes in certain parameters. In particular the interaction between the three goals is analysed to determine whether there is conflict between any of the goals and, if so, what the trade-offs between the conflicting goals are.

Jan 1, 1979