Search Documents

By Joseph Cervik

Methane drainage methods can be broadly classified as surface or underground. Surface methods make use of vertical and slant holes. The underground method discussed in the present paper involves horizontal drilling from shaft bottoms and from locations along the periphery of mines. Every foot of hole drilled in coal from under- ground locations is productive and gas flows increase as hole length increases. Therefore, underground techniques have a great potential for producing large-volume flows of methane. Pumps to dewater the horizontal holes are not necessary because gas pressure forces the water out of the hole. Methane can be recovered through the use of a simple and inexpensive gas-water separator. Hydraulic fracturing, which has been used successfully to stimulate gas flows from vertical holes, has not proved practical in the case of horizontal holes.

Jan 1, 1980

By M. C. Mound, E. Gallestey, C. Colbert

Continuous operating performance and high profit is one of the major concerns in the mining industry. Information systems are expected to reinforce and enable conformance to these requirements. The companion efforts of business management and production information systems press for tighter integration to avoid over-laps, multiple instances of similar data, and expensive maintenance of databases. Implementation of advanced intelligent systems throughout a mine operation can reduce costs, optimize investment and create a shorter payback via conversion of the data accumulated by field and process devices into information, and subsequently, into decisions. However, in order to harness the potential power inherent in these intelligent devices, adequate and flexible modular knowledge-based solutions are required. Fortunately, there has been at least one such practical response to this challenge, namely the ABB IndustrialIT portfolio. With these tools in place, production efficiency is reached via integration of process, production, and quality information. Moreover, they permit immediate detection and remedial action to changes to process and boundary condition variables. Finally, using advanced optimization techniques supported by dedicated mathematical models, they allow for economic process optimization (process set points and coordination thereof, energy management, production planning, energy supply contract optimization, etc) of the plant as a whole.

Jan 1, 2004

By J. Walden, S. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers mounted in suspension components can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a Global Positioning System is recorded at the same time as shock pressures or acceleration data, then the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck.

Jan 1, 1999

By James R. Jones

The concern for air pollution goes back centuries as will be seen from this quotation : "Strife and coal, it seems, have a hand-in-hand historical relationship. It was thought by some . . . in the Middle Ages that burning coal filled the air with dangerous poisons. So great was the concern that in 1306 King Edward I of England passed the first and unquestionably the harshest air pollution legislation edict that history will record. His proclamation declared the use of coal an act punishable by death." As related to coal mining, the air pollution problem is primarily that of its customer when using the fuel. Thus the major impact relates to markets for coal rather than the actual mining operation itself. In the vicinity of the coal mine the problem is principally related to fugitive dust from roads, transfer facilities, loading facilities, crushers, etc., and particulate matter (dust or fly ash) from thermal dryers and air cleaning tables.

Jan 1, 1981

By Myron W. Mellor

Our efforts at McNally, to find a better way to mechanically separate particles from liquid in a slurry have led to the development of two new centrifuges. The first unit utilizes a slotted opening screen as the filter media and retains all plus 200 Mesh and most of the 200 by 300 Mesh particles. The second unit is a solid bowl centrifuge with a novel method of removing the solids and delivers an effluent containing as little as 300 PPM solids in suspension. The first unit was designed to separate particles in the range of about 1 MM x 0 or smaller top size from the liquid slurry and produce solids having low surface moisture content, and a liquid concentrate containing a low percentage of solids. A prototype of this unit has been in the field undergoing tests for over two years. A few of these test results are shown in Tables I & 11. Testing has been mostly limited to the field of coal, how- ever this does not mean that the machine would accept only coal slurries. The machine has produced a dewatered product having as low as 5.5% surface moisture, and an effluent containing as low as 1.4% solids and handled slurries containing from 15 to 50% solids by weight.

Jan 1, 1975

By Alfredo Valdivia, Jesus Schabib, Vojtech Gall, William Cao, Curt Cicileo, Andrew J. Thompson

"The East Side Access Project (ESA) involves the construction of geometrically complex underground structures including a large number of caverns and bifurcations. Initially conceived as dual lined structures with either traditional concrete or shotcrete final linings (SFL), construction economy, advances in concrete placement technology and scheduling among others led to a wide use of what is referred to as freeform or pneumatically applied concrete (PAC) for the construction of tunnel final linings. PAC is a method of applying concrete without using formwork, where a wet mix concrete is pneumatically installed to encase reinforcement to full lining thickness. PAC has been widely adopted at ESA well beyond initial expectations. The paper addresses the design and construction aspects of the PAC method and contrasts it to traditional SFL lining placement. The experience made provides guidance for future PAC and SFL applications. THE EAST SIDE ACCESS PROJECT AND USE OF FREEFORM CONCRETE The Long Island Rail Road (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodates New Jersey Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the New York City Transit (NYCT) Subway System and Metro North Rail Road. The construction includes mining and lining of new tunnels and facilities under Manhattan and Queens. The tunnels run from Queen’s Sunny Side Yard through the existing 63rd St. Tunnel, underneath Manhattan’s Park Avenue until termination at 37th Street. Differing types of tunneling methods and final lining systems are being used depending on the ground conditions, geometry and size of the excavation, site constraints and functional requirements. Mining of the Queens segment of the ESA Project involved soft ground tunneling by pressurized face tunnel boring machines, cut and cover construction, and conventional tunneling. The Manhattan segment of the ESA Project involves mining in hard rock by tunnel boring machines, drill and blast, and road header."

Jan 1, 2016

By Daniel E. Collins

Massive banded Fe-Zn-Cu-Pb sulfide deposits in the Bagdad are associated with metamorphosed eugeosynclinal mafic volcanic and intrusives rocks Precambrian age. The geologic environment is very similar to that of the Jerome-Prescott area which lies 70 km. east of Bagdad. Mining of massive sulfides deposits began in 1917 on the Copper King mine in spite of its early discovery and the discovery of the Old Dick mine in 1882. The first shipments of zinc ore from the Copper King were hand sorted and averaged 46.89% Zn, 5.7 oz. Ag, 3.58% Pb and 1.68% Cu. Oxidized copper was first produced from the Old Dick mine in 1943~ In all, five deposits of massive sulfide ores have been mined in the Bagdad for a total production of nearly 2 million tons with an average grade of 12.0% Zn and 3.6% Cu. The largest deposit, the Bruce mine is currently closed because reduced metal prices and has produced a total of 823,000 tons of Zn-Cu ore to date. Mining of massive sulfide ore in the Bagdad area is presently idle. However, the potential for locating yet undiscovered ore bodies is good. Exploration for new ore bodies is difficult at best due to the complex geologic history of the area, the small size of individual ore bodies and lack of understanding as to the formation of massive sulfide deposits. The purpose of this investigation was to obtain a better understanding of the host rock formations through detailed geologic mapping, petrography and chemical analysis.

Jan 1, 1977

By A. Fleming

The exploration process, like any other commercial activity, can only succeed if the objective of the exercise is clearly defined and persistently pursued. Successful exploration requires properties, funding, personnel and persistence. Many of us have years of experience in conducting exploration in our countries of residence. Conducting exploration in a foreign country, however, requires a number of significant other criteria.

Jan 1, 1997

By Werner T. Meyer

Technical modification of traditional zinc- and lead-based products is moving the metals into diversification is particularly apparent in two areas. The evolution of diverse types of heavy-duty vehicles that employ lead acid batteries. and The development of Galfan™ -- a zinc / 5% aluminum/mischmetal coating alloy designed to provided zinc-coated anti-corrosion protection in applications that are not well suited to traditional galvanizing. Because any product breakthrough must be accompanied by advancement and customer oriented thinking at every step in the chain of production and distribution, a concerted effort is required for market evolution to live up to its potential. As such, all those involved in the metals industries should not only track the progress made by technical and marketing innovations, they must participate as much as possible in their development and promotion.

Jan 1, 1986

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

"The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities (82%) may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis. Among coal and rock dust exposure, high noise levels, roof and rib falls, and the potential for fires and explosions, operating and working with heavy machinery poses a significant risk to miner safety. One of the most hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 39 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are now required on all operating CMMs in underground coal mines with the exception of full-face CMMs [1]. Commercially available proximity detection (cPD) systems are based on the principle of magnetic flux density (B-field). Typically, four magnetic field generators are positioned on a CMM, and personal alarm devices (PADs) are worn by the miners that detect magnetic flux density difference. As a miner wearing a PAD gets closer to the machine, the flux density increases. Zones can be constructed around the machine so that an alarm will trigger on the PAD based on the flux density."

Jan 1, 2016

By C. D. Wittreich

The University of Idaho, Department of Metallurgical and Mining Engineering, through the Generic Mineral Technology Center, has been engaged in mine design research at the Lucky Friday Mine, Mullan, Idaho. The purpose of the research is to develop and implement the longwall underhand cut-and-fill mining method for conditions at the Mine. The longwall underhand cut-and-fill mining method involves backfilling mined stopes with a compacted tailings-cement mix. After the backfill has been allowed to cure, mining is resumed from underneath. Horizontal stresses in the Lucky Friday Mine are exceptionally high and rock bursts are a common problem. Beus and Chan (1980) have reported a 2:1 horizontal to vertical stress ratio at the mine with a 65-MPa (9,500-psi) maximum horizontal stress at the 1,295-m (4,250-ft) level. Using this mining method under these stress conditions, it is desirable to have a backfill material that has sufficient strength to safely carry the high horizontal wall loads while minimizing external steel supports.

Jan 1, 1987

By Robert D. Deister

The Buick Concentrator represents state-of- the-art technology in automated digital process control operation utilizing a centralized computer. The process control strategies implemented at Buick are no longer new to the industry but the successful application of these developments is still rather unique in North America. Productivity improvements, determined to be a direct result of the process control developments, are the primary topics of this paper. Emphasis is placed on metallurgical benefits including both lead and zinc recoveries, lead concentrate grade and reductions realized in reagent consumptions, operating costs and personnel. The productivity improvement discussion is preceded by a concentrator description and a brief history of the process control development at Buick. Current control strategies and future applications are presented afterward.

Jan 1, 1985

By Carol A. Hill

Native sulfur occurs with barite, celestite, and bioepigenetic calcite in the Culberson, Pokorny , and Leonard Minerals deposits, Delaware basin. The sulfur in these deposits, in "castile" masses, and in deposits of the Fort S tockton district have 6 34s values between +9 and -15. Native sulfur in the caves of the Guadalupe Mountains is somewhat lighter [(634s = -15 to -25)]. Barite in the Culberson, Leonard Minerals, and Comanche Creek sulfur deposits have 63% values of +35 to +73; celestite in the Culberson and Leonard Minerals occurrences have values of +38 and +36, respectively, and 87Sr/86Sr values of 0.707808 and 0.708138, respectively. Barite associated with sulfide, deposits, Guadalupe Mountains, have [634s] values of +41 to +62. Barite at Seven aeart Gap, Apache Mountains, is somewhat less enriched in heavy sulfur [(634s = +14 to +37)].

Jan 1, 1992

By John W. Amos, John A. Christophersen

The Deister No. 7, "77" and "88" Coal Washing Tables have been used by the coal industry in the cleaning of finer sizes of coal (-1/2") since washing of coals became necessary. This paper will deal with the in-plant use of the CONCENCO "88" Deister Coal Washing Table, along with a brief description of the Deister Refuse Superscalper. Efficient in-plant operation of the Deister Coal Washing Table can be accomplished by the adjustment of six basic variables. These variables are: 1. Headmotion 2. Feed 3. Riffle Pattern 4. Dressing Water 5. End Elevation Adjustment 6. Side Tilt Adjustment VARIABLE NO. 1 HEADMOTION The reciprocating movement of the "88" Table is developed within the headmotion entirely by rotating eccentric weights. Four parallel shafts each carry pairs of eccentric weights (Figure 1-A). The shafts are geared together with gears of 2 to 1 and 1 to 1 ratios, so that the two shafts in vertical alignment which carry the small eccentric weights operate at twice the speed of the other two shafts. The other two shafts are also in vertical alignment with each other and carry large eccentric weights. As power is supplied to one high-speed shaft, once each revolution the forces produced by the large eccentric weights are reinforced and then opposed by the small eccentric weights in a horizontal plane. The direction of movement of the table decks is reversed much more sharply at the forward end than at the backboard end of the stroke, causing material to move toward the refuse end of the table. Because in the vertical plane all centrifugal forces oppose each other and cancel out, there is no vertical movement and virtually no impact to the support steel. The "88" Coal Washing Table is suspended by wire-rope cables from three overhead steel beams, and operates with a perfectly uniform and exact differential motion curve in every stroke (Figure 1-B). The decks, being attached to the headmotion, are reciprocated in a parallel line from the head- motion to the refuse corner at speeds varying from 260-300 strokes per minute. Both length of stroke and speed are set at the factory for the coal characteristic desired and should not be changed. A 3 HP motor is mounted on the top of the headmotion and uses 3 V-belts to transmit driving power to the headmotion. The headmotion must be kept running on a horizontal plane. Punch marks are provided on the side and end of the main frame for use in leveling the motion (Figure 1-C). In leveling the motion, the work must always be done with two cables. To level the long side of the headmotion both front or both rear cables are raised or lowered to bring motion back to level. To level side to side, both right side cables or left side cables are raised or lowered to bring motion back to level VARlABLE NO. 2 FEED When tabling different size coals, each deck of a "88" DIAGONAL-DECK Coal Washing Table will handle feeds as described in figure 2-A.

Jan 1, 1988

Exploration for SX-EW copper deposits and plant operation depend largely on the copper and gangue mineralogy inasmuch as? they govern the feasibility of leaching. Mineralogical parameters are pivotal in identifying if an ore is suitable to dump, heap, thin layer, vat or agitated leaching and/or if the ore requires curing, bioleaching or alternate lixiviants. Problems in metallurgical testing, production leaching and recovery forecasting are very often related to lack of mineralogical data. This presentation will illustrate the use of quantitative mineralogical analysis for exploration, acquisition assessment and optimization of copper leach operations.

Jan 1, 1996

By Joel Nonnweiler, David Young, John Hawley

The Sacramento Regional County Sanitation District has implemented a billion-dollar interceptor system master plan, including the 31 km (19 mile) long Lower Northwest Interceptor (LNWI). For the two LNWI Sacramento River crossings, pipe-jack/micro tunnel drives in excess of 300 meters (1,000 ft) from 30 meter (100 ft) deep shafts in mixed soil conditions below the water table were considered, as were600 meter (2,000 ft) tunnel drives utilizing pressurized-face tunnel boring machines. Operation and maintenance concerns, predicted flood scour, and levee concerns are discussed. A risk assessment process was used to select both profile and construction method. Construction will begin in mid 2004.

Jan 1, 2003

By D. Zaharaki

The optimisation of geopolymer synthesis was studied bymixing low Ca electric arc ferronickel slag with kaolinite, sodium silicate solution, sodium hydroxide pellets and water. The pulp was heated at low temperatures and left for curing at room temperature. Through statistical analysis it was shown that the factors with the most statistically significant effects on the compressive strength of the produced geopolymers are slag particle size and aging period. XRD and FTIR studies provide useful information regarding the progress of geopolymerisation mechanisms. Finally, studies regarding the durability and structural integrity of the produced geopolymers were also carried out.

Jan 1, 2006

By G. S. P. Pereira, E. M. R. Santos

Acid mine drainage (AMD) is a serious environmental problem in mining activities. Prediction is the first step for evaluate the potential of acid generation and there are some possible methods to estimate it. They are described as static tests, which examine the balance between acid producing and acid consuming materials, and kinetic tests, which attempt to predict drainage quality overtime. Static methods are very simple and give a qualitative classification of the ores based on their potential to generate acid drainage. The characterization of ores to determine their acid producing potential is vital for the prevention of long term environmental liabilities. Laboratory tests were conducted under different methodologies to predict the acid producing potential of sulphide overburden, ore materials and tailings from a deposit of copper ore.

Jan 1, 1999

By Roberto Pimentel de Souza

CURD started producing pellets in 1969, with one two-million ton straight grate plant. In the beginning of April '73, the second unit came on stream with an additional capacity of 3 million TPY of pellets. In January '77, the third unit started, bringing the annual capacity to 8 million TPY. For the present year 3 more units, 3 million each, are expected to begin production. CVRD's experience is given about the use of different binders and additives. Over the years several kinds of pellets have been produced to satisfy the market requirements. General quality information is given regarding each.

Jan 1, 1978