Search Documents

By A. Pavlides

The purpose of this work is to conduct a preliminary analysis of the spatial variations of the thickness of lignite layers in the area of the Amyndeo mine, and to estimate the lignite reserves of the mine. The reserves are estimated by the method of the Voronoi diagrams, using a group of mirror points to close the polygons around the boundaries of the mine. Two data sets are investigated. The first one corresponds to an exhausted part of the mine. The derived reserves estimates are compared with the actual data obtained by the Public Power Corporation (PPC) to validate the analysis. The second data set extends over the entire mine, and it is used to derive an approximate estimate of the total lignite reserves. A geostatistical analysis of the total layer thickness is performed. The experimental semivariograms are evaluated for both data sets in different spatial directions. Two possible theoretical models for the experimental semivariogram (the exponential and a novel Spartan model) are compared and discussed. An interpolated kriging map of the total thickness variation is produced accompanied by a map of the kriging precision. The performance of kriging interpolation is discussed in terms of cross validation measures.

Jan 1, 2007

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By Qingxia Liu, Chen Tingzhong, Chen Jin, Yang Xiaosheng

It is common problem (Huan Xinsheng, etc.,l992)for most iron ore concentrators in China that the concentration of thickened tailings is lower than the need for economical transportation. To solve the problem, two methods of improving the properties of the existing thickeners and using separate thickening technique have been applied in three iron ore concentrators. However, in the case of the Daye iron concentrator a new technique of cyclone-flocculated sedimentation was developed by present authors and verified by experiments. The new technique employs efficient hydrocydone designed by authors in conjunction with a low cost flocculant named KLP.

Jan 1, 1995

By Sidney A. Hiscock

INTRODUCTION Lead and zinc are today rightly regarded as sister metals. Historically, however, they differ markedly with lead being known and in general use as the metal since 3000 BC in several countries which at that time might have been described as mature economies. Zinc was not isolated and recognised as an industrial metal with distinct and valuable properties until about 1700-1800 AD (although it had, of course, been utilised as a constituent of brass for some 2000 years previously). c were well established as industrial metals by the beginning of the 20th century. The present paper briefly reviews the overall growth in world consumption* and changes in the three main areas which today represent the mature economies or industrialised areas, i. e. ,Europe, the United States and Japan. Trends in overall consumption are determined by the demands for the individual uses for lead and zinc. The changes in patterns of use in the industrialised areas - individually and collectively - and reasons for the changes are also considered. LONG TERM TRENDS - 1900-1984 The World Picture Since the beginning of the 20th century the world consumption of lead (3.9 million tonnes in 1984) has grown almost fourfold and that of zinc (4.7 million tonnes in 1984) is almost eleven times greater than it was in 1900. The long-term trend has been one of continuing expansion for both. metals although the pattern has been severely disturbed at certain periods, for example in the years immediately following the two world wars and at times of marked recessions in industrialised areas. Apart from such major setbacks, new levels of consumption have been established regularly every few years. Recently, however, consumption has not really grown and with only a slow and partial recovery in world industrial activity at present, there is no indication that the peak consumptions of 4.2 million tonnes of lead, set in 1979, and 4.8 million tonnes of zinc (1973) will be exceeded in the near future. The growth in world lead and zinc consumption since 1900 is shown in Figure 1 (which includes changes in copper and aluminium for comparison). Overall growth over the period 1900-1984 has been about two percent a year for lead and about three percent for zinc (annual growth for copper has also been about three percent). Increases in tonnage consumption and growth rates by decade for lead and zinc are summarised in Table I. However, the growth rates by decade sometimes conceal very large individual annual increases and decreases. For example, in 1975 lead consumption fell by 13 percent and zinc consumption by 22 percent compared to 1974. In 1976 consumption of lead and zinc rose by 12 percent and 18 percent respectively. The years when consumption 'landmarks' (ie one, two, three and four million tonnes) were first reached are shown on Table 2. Clearly, the pattern of shorter periods being required to attain each extra million tonnes of consumption was broken in the 1970's. The consumption of zinc overtook that of lead for the first time in 1940, and since 1946 has always been at a higher level. Trends in industrialised areas The two key industrialised areas at the beginning of the 20th century were Europe and the United States which between them accounted for some 95 percent of world lead consumption and 98 percent of zinc consumption. Figures 2 and 3 show the growth in lead and zinc consumption, and Figures 4 and 5 the percentage shares for each area since 1900. Europe has usually been the major user of lead except for some years in the 1920fs, most of the 40's and early 50's when consumption in the United States was larger. In 1900, Europe accounted for about 64 percent of world lead consumption and the United States just over 30 percent. Currently, Europe takes about 40 percent of world consumption and the

Jan 1, 1986

Copper cathode and Uranium Oxide production at WMC (Olympic Dam Corporation) Pty. Ltd. involves processing leach liquors through a copper solvent extraction plant followed by a uranium solvent extraction plant. This paper discusses the processing problems, metallurgical testwork and circuit changes made due to contamination of amine in the oxime circuit and vice versa.

Jan 1, 1996

By James M. Link

The transportation of solids by slurry pipeline is a rapidly growing field. Although early patents date from the latter part of the nineteenth century, it has only been within the last twenty years that successful long distance slurry transport lines have come into their own. The pioneering efforts in this country include the gilsonite slurry pipeline from Bonanza, Utah, to Grand Junction, Colorado, and the coal slurry pipeline from Cadiz to Cleveland, Ohio. Both of these lines were constructed in 1957 and had a combined annual capacity of about 360 million ton miles. Although the Cadiz pipeline was mothballed in the early 1960's, the interest in slurry transport systems continues to increase and one engineering and construction company is predicting that by 1980 an annual slurry system rate of more than eight billion ton miles will be achieved. The design and construction of cross-country pipelines for fluids such as crude oil appears relatively simple when contrasted against the complex problems encountered in slurry systems. Considerable effort has been expended in hydraulic research laboratories in an attempt to improve our understanding of slurry behavior. This effort has been rewarded with considerable success and is best illustrated by the large number of slurry systems now planned or under construction. However, slurry transport in pipelines is still, in many instance more of an art than a science. In order to minimize the risk factors in the construction and operation of large scale slurry systems, studies are frequently conducted in pilot scale test

Jan 1, 1972

By E. J. Freech

In this part of the two-part paper we discuss briefly the adaptation of the comminution model to describe the observed behavior of an industrial grinding circuit. Although reported verification of comminution models for continuous systems is limited, some interesting work has been reported 1,2 recently. The data acquisition and modeling efforts are described first, followed by discussion of some of the simulation results. Observations pertinent to steady-state operation are presented followed by a description of the application of a dynamic model of the grinding circuit for synthesis and evaluation of grinding-circuit control. The pilot-scale work indicated the comminution model should be capable of describing an industrial size-reduction process. Recognizing the broad utility of a process model based on first- principles, the Industrial Nucleonics Corporation of Columbus, Ohio, embarked on a joint program with the Duval Corporation of Tucson, Arizona, to evaluate the industrial applicability of the models described in Part I. This program was conducted in a grinding circuit, which included a rod mill 12.5 feet in diameter and 16 feet long and a ball mill 12.5 feet in diameter and 14 feet long, at Duval Corporation's Esperanza property3. The rod mill was operated in open circuit and the ball mill in closed circuit with cyclone classifiers.

Jan 1, 1970

By Don Opacic

The disposal of sludges and other similar industrial wastes is a major problem. Liquid wastes from industrial operations, when treated, produce significant volumes of sludge which are difficult to dispose of, because of the chemical and physical properties of the sludge. In the mining industry sludge is produced from various water treatment operations, in particular mine drainage neutralization. Waste water from coal preparation plants also produces a sludge however the sludge is in fact a slurry containing clays, coal fines and coal impurities. In many areas the disposal of these sludges is producing a serious problem. Mine drainage sludge consists of a variety of hydrous iron oxides, usually ferric oxides, contaminated with other neutralization products such as calcium sulfate. The volume of sludge from mine water or mine

Jan 1, 1973

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By R. M. Imhof, M. J. G. Battersby, G. Ciernioch

Pneumatic flotation is rapidly becoming accepted in the main stream of flotation techniques. Imhoflot is a pneumatic flotation process that in recent years has undergone progressive development. It combines short flotation times with excellent selectivity by employing intense pre-aeration and dispersion. K+S GmbH (K+S), Germany, has installed a complete Imhoflot flotation plant at its Sigmundshall plant. The plant treats hard salt consisting of sylvine, halite, anhydrite and kieserite. The reason for selection was that Imhoflot achieves the required grades of plus 60 weight percent K2O whilst offering lower operating costs than conventional flotation installations.

Jan 1, 2002

By Jürgen Lotze

Previously (1981), it was shown that the fiscal policy practised by some IBA-member countries is mainly responsible for a significant shift of known bauxite resources into higher processing-cost categories. The possible impact of politically imposed fiscal costs on the competitiveness of relevant bauxite resources is investigated in detail by means of a model calculation procedure.

Jan 1, 1984

By George L. Atwood

The Monsanto Company's Henry Mine is located 17 miles northeast of Soda Springs, in the southeast corner of Idaho. Ore being mined is phosphate rock which lies in the Permian Phosphoria formation. The ore is the raw material for Monsanto's three furnace elemental "P" plant near Soda Springs. The finished product from the furnaces is elemental phosphorus which is subsequently used in the manufacture of detergents, food preservatives, fire retardants and other consumer items. Mining is by open pit methods using 0-9 crawler tractors to rip and push-load rubber tired scrapers in stripping and mining operations. The equipment spread consists of six D-9G crawler tractors, four Caterpillar 6578 scrapers, eight Euclid S-24 scrapers, one Reich T750 drill and one Caterpillar No. 16 patrol plus various support equipment. Stripping is performed on a 12-month basis, two shifts per day. Mining is performed mainly in the summer months on a one shift basis. The hauling season begins May 15 and ends November 1 due to freezing weather and snow conditions. Annual production is 1,000,000 tons of phosphate rock and 2,500,000 to 3,000,000 yards of stripping. Stripping, mining and hauling is performed for Monsanto by Dravo-Soda Springs, a mining contractor. Dravo-Soda Springs owns, operates and maintains all equipment used in stripping, mining and hauling. The contractor is paid for stripping by the bank yard and for ore mined and hauled on a tonnage basis. The Monsanto elemental phosphorus plant began production in 1952 with ore being trucked to the plant from the Ballard Mine. Haulage was over public roads in 15, 24-ton semitrucks. A private haul road was constructed from the Ballard Mine to the Monsanto Plant in 1958 and 1959 to accommodate trucks with two twenty-yard trailers. This 11/ mile road was first used in the 1959 hauling season. In 1965, five new Kenworth tractors with two, 'forty yard trailers were introduced into the haulage system. These units carried 120 ton payloads and were used until

Jan 1, 1972

By Stephen J. Reynolds

Arizona's geologic history is complex, resulting in a diversity of rock types and earth materials, including those of commercial interest. Regional variations in geologic history gave rise to three geologic provinces and an inequitable distribution of both metallic and nonmetallic mineral wealth. The Colorado Plateau is largely composed of flat-lying Paleozoic and Mesozoic sedimentary rocks and late Cenozoic volcanic fields and sedimentary deposits. Associated resources include gypsum, halite, sylvite, clays, specialty sand, flagstone, volcanic products, and aggregate. The adjacent Transition Zone features a large expanse of Proterozoic rocks, economically important Devonian and Mississippian carbonate rocks, and Tertiary volcanic and sedimentary materials. Nonmetallic resources in this province include facing and dimension stone, aggregate, decomposed granite, chrysotile asbestos, gypsum, clay, barite, fluorspar, zeolites, and limestone used for lime, cement, and railroad ballast. The Basin and Range Province has the most complex geologic history and, therefore, the most diverse assemblage of industrial mineral occurrences. These include halite, gypsum, clay, aggregate, decomposed granite, diatomite, zeolites, perlite, pumice, kyanite, limestone, marble, stone, and others. In addition, young stream deposits yield vast quantities of sand and gravel, Arizona's most economically important nonmetallic mineral commodity.

Jan 1, 1987

By J. A. Brierley, C. L. Brierley

The history, current applications and future of biotechnical developments in the metals' extraction industry are reviewed. Bioleaching of copper minerals continues to be the most significant application. Uranium bioleaching was successfully demonstrated at industrial scale. Developments are now being made in biooxidative pretreatment of refractory gold concentrates, ores and low-grade materials. Advancements are forthcoming in water and solid mine waste bioreclamation, including metals' biosorption, wetland treatment of acid mine drainage, and biodegradation of cyanide in spent, heap-leach operations. Better understanding of the types and functions of microorganisms involved in metal interactions could advance genetic engineering applications in bioleaching and bioreclamation.

Jan 1, 1993

By T. R. Ley

"INTRODUCTION Brutally honest mining executives will tell you that “safety is job #1 but.. dollars are also extremely important”. When economic times are tough, as they are now in mining, it can feel like you need to choose between safety and cost control. Leading edge companies know that it is excellence at both that provides the best performance. FLUID POWER SYSTEMS Fluid power systems are ubiquitous in mining – longwall systems, continuous miners, drills, haul trucks and excavators, etc. And fluid power systems are getting more powerful and using higher pressures to move greater volumes and achieve higher productivity. Average operating pressures in mobile equipment has been rising to 450 bar (6,500 psi) over the last decade. With increased system pressure comes ever increasing levels of stored energy. Stored energy that, if released in an uncontrolled fashion, can do tremendous harm to people and things.Fluid power systems are composed of pipe, flexible hoses, pumps, valves and actuators. They are filled with fluid (mineral oil or fire-resistant) to transmit power to where it’s needed for performing work. With time and use fittings can loosen, component performance diminishes and hoses wear and tear. In hostile environments, like coal mining, hydraulic hoses can fail in as little as 2 years according to DGUV (umbrella association of German Accident Insurers), maybe sooner in some particularly challenging environments. FLUID POWER SYSTEM SAFETY While appearing simple and benign on the surface, fluid power systems, particularly such systems on mobile equipment, have many potential hazards. Hazards that most workers aren’t aware of – particularly young, new hires. And those hazards that can quickly turn deadly. During the past couple of years, including at last year’s SME Conference, I talked to a wide variety of mining people about high pressure fluid injection injuries. Some people, often with little or no field experience, never heard of it. But, people with mine operations / maintenance experience were almost always aware of such injuries.Some had even seen it happen right in front of them. But most claimed it didn’t happen all that often. It just wasn’t seen as a problem!"

Jan 1, 2016

By Steven I. Majtenyi

INTRODUCTION The heavy risk inherent in all underground construction projects contributes significantly to the high cost of transportation tunnels. First, the knowledge of this risk leads the engineer to design conservatively. Second, the cost overruns are still common with a high proportion of them originating from corrective measures needed when unforeseen problems develop during excavation. These unforeseen problems includes - encountering unexpected objects, materials and water conditions - experiencing an unforeseen behavior of the materials - damaging property beyond the expected range of influence of the tunnel construction. To minimize these expenses, more emphasis is being placed on well planned and interpreted site investigation programs in the final design and planning stages of the project. It is well known that the cost of a planned excavation is less than the cost of dealing with the same conditions when they are encountered unexpectedly. Therefore, the objective of site investigation is to provide a complete set of reliable data for designers and contractors that is continuous along the projected tunnel alignment. Two alternatives axe available to achieve this objective; - for shallow tunnels, it is often feasible to generate continuous data by drilling appropriately spaced, vertical bore holes and applying sensing techniques for interpolation (1, 8). - for deep tunnels, or certain urban tunnels under existing structures, closely spaced, vertical bore holes are not feasible except for narrow zones at the portals. In such cases direct horizontal penetration may be required that may be complemented by radial sensing to extend the range of information.

Jan 1, 1976

By H. R. Hammond

The situation of The Consolidated Mining and Smelting Company of Canada Limited, or Cominco, may be somewhat unique in that the Company is not only a manufacturer of ammonium nitrate, but as a mining company is a major user of its own product. This situation has resulted in highly successful application of ammonium nitrate-oil explosives. Several noteworthy techniques have been developed and others have been improved. Use of this material in the mining industry has led ammonium nitrate producers to adopt the term nitro-carbo-nitrate or INN for ammonium nitrate-oil blends. A small blending plant at Cominco's largest mining property, the Sullivan Mine, at Kimberley, B.C., is producing more than 80% of all the explosive used at the Sullivan, and is supplying two other Cominco mines. Application has required intensive research to determine the best forms of ammonium nitrate for use in small holes drilled for development and long-hole stoping. It has led not only to experiments to determine the best blending oil, but also to development of loading techniques to the point where NCN is being moved through loading tubes over 700 feet. It has required research into mining practices such as hole arrangement and blasting of development cuts. It has resulted in the development of a special product for secondary breaking. All this has been accompanied by the recognition of the importance of insuring safe practices at every stage.

Jan 1, 1963

By M. Mikhaylenko

The most common methods of processing of uranium ores is sulfuric or carbonate leaching with conversion of hexavalent uranium to uranyl carbonate or sulfate anionic complexes followed by sorption of the later by strong base anion (SBA) exchange resins. It is known that chloride anion has high affinity for SBA resins so that it depresses sorption of anionic complexes of uranyl. Application of the SBA resins becomes impractical for recovery of uranium when chloride concentration in pregnant leach solution exceeds 3-5 g/l [1-3].

Jan 1, 2012

By Joseph W. Leonard

By combining statistical methods with specialized coal technology, novel and widely applicable procedures are developed which are useful for making important decisions based on coal seam structure. By analyzing such properties as ash in visual coal types of seam cross sections and by processing the ash data to 100 gram increments of coal ranging from the top to the bottom of the seam, intraseam comparisons between data populations of samples from a given seam and a reference seam can be made. Moreover, illustrations are presented for estimating the number of drill cores required to purchase a specified level of sampling accuracy together with procedures for determining the probability that different coal scan cross sections are not unlike and by inference are therefore comparable. Such comparisons can be valuable when making important, costly and long prevaling decisions involving coal exploration, mining, preparation and utilization.

Jan 1, 1969

By H. Dreissen

Upgrading of low-concentration ores is of growing importance today. The Heavy Medium Cyclone Process, thanks to strong centrifugal forces, effectively separates particles varying only slightly in specific gravity but widely in size. The paper discusses the separation efficiency, the method of assessing that efficiency, and the influence of such factors as medium solids. The operating results of nine heavy medium cyclone plants handling following minerals are reported: barite, wolfram, iron, magnesite, diamond, lead-zinc, fluorspar, rocksalt potash. Highlighted are an improved recovery system for heavy medium and some other developments, such as techniques for separation down to 0.1mm and the application in the field of recycling.

Jan 1, 1980