Search Documents

By H. Chu

Selective Agglomeration experiments carried out to clean ultra-fine coal are examined. Effect of feed size, pulp density, coalescing agent dosage, and mixing intensity and duration on the kinetics of agglomeration are principally evaluated. A computer coded population balance model governing agglomerate size distribution and composition utilizing coalescence and breakage mechanisms is developed. Model calibration, verification and extension are analyzed.

Jan 1, 1987

By Richard W. Cannon

INTRODUCTION The authors, by means of this paper, will attempt to show the role of Induced Polarization and Resistivity surveys in the discovery of the orebodies of Gibraltar Mines Limited (N.P.L.). In this paper, we will also attempt to show the importance of conducting large enough surveys in order to properly evaluate the results obtained from these surveys. LOCATION The orebodies of Gibraltar Mines Limited (N.P.L.) are located on the western slope of Granite Mountain, central British Columbia (52°30' north, 122°16' west) (See Fig. 1). The property lies approximately 28 miles north of Williams Lake, B.C. and can be reached by way of 10 miles of newly improved road from McLeese Lake, on the Cariboo Highway. The area in and around Gibraltar Mines has a moderate topographic relief with elevations between 3,500 and 4,100 feet. {EARLY HISTORY AND GEOLOGY The present Gibraltar Mines property before amalgamation consisted of the Pollyanna property (Duval-Canex) and the Gibraltar property (original Gibraltar Mines) as well as some Coast Silver and McLeese Lake Copper claims (See Fig. 2). The Pollyanna property was first described in the 1917 B.C. Minister of Mines Report which referred to it as the "Rainbow Group". The development at that time consisted of several open-cuts on copper bearing quartz veins.

Jan 1, 1972

By Pat Wilmoth, Joseph P. Gildner, Dan Nowak, Shane Yanagisawa, Don Z. Painter, Gordon F. Revey

Frontier/Traylor is presently completing construction of twin tunnels for the Tri-County Metropolitan Transit District of Oregon’s (Tri-Met) westside lightrail system. The tunnels are each 4,550 m (14,935 ft) in length and 6.48 m (21.29 ft) in diameter. The 1/3 of each tunnel was driven from the west portal using drill and blast methods and the remaining 2/3 was driven from the east portal using a TBM. The paper describes: The difficulties encountered by the TBM mining the weathered Columbia River Basalts. The execution of drill and blast work despite challenging ground conditions, stringent noise and vibrations specifications, and public relations problems. The excavation and lining of the Washington Park Station 79 m (260 ft) below the park zoo.

Jan 1, 1997

By W. E. Lytle

Environmental permitting is a critical component for joint-venture projects located in the Commonwealth of Independent States (CIS). This paper presents the basic CIS regulatory environmental requirements for permitting of a hypothetical mining source and emphasizes air permitting. Topics which will be covered include: the Expertiza process, air pollution quantification, data requirements, and air pollution modeling protocol. A comparison will be made between permitting requirements for air pollution sources in the United States and a CIS country, Kazakstan.

Jan 1, 1998

By Emad Iskander

The seepage forces generated around pressurized water tunnels in rock are investigated using the analysis tools of geomechanics. The theoretical background of the two-phase material behavior is explained and the equations of motion and continuity are presented. Applications on two case studies typically occurring in practice deal with the required minimum rock cover for a pressurized tunnel and the separation between two tunnels carrying different heads. The rock mass behavior as described by the Mohr-Coulomb and Hoek-Brown material models is investigated by numerical analyses and the results are compared. The effect of key material parameters on the safety factors and the associated modes of failure is discussed.

Jan 1, 2008

By Sun K. Kim

Hydrometallurgical processes are not free of environmental regulations. A clear understanding of the regulations under which the minerals industry operates delineates processing requirements at early stages. This paper deals' with federal environmental regulations with emphasis on the hazardous waste regulations promulgated in May, 1980. The procedure of EP toxicity test and an example of the test are described. Brief account is given of the current trend and future outlook of regulations.

Jan 1, 1982

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

In 1993, the United States' economy grew at a rate of about 3%. The Gross Domestic Product rose to $6.4 trillion. With more than 258 million people - 599,000 in mining including petroleum - the United States has more than 100 million dwelling units and more than 190 million licensed motor vehicles. New private housing starts rose 7% to 1.3 million units, new car production fell 3% to 5.5 million units and truck and bus production rose 21 % to 4.9 million units. The rate of inflation was under 3% and the prime rate of interest 6%. The Producer Price Index (1982 = 100) was unchanged from 1992 for fuels and re¬lated products and power at 80 and met¬als and metal products at 119, while chemicals and allied products rose 2% to 128 and non-metallic mineral prod¬ucts rose 2% to 120. The merchandise trade deficit rose 27% to $116 billion.

Jan 1, 1994

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By W. Hu

Traditionally, coarse wolframite ore processing has been done almost exclusively by gravity concentration methods. However, there has been a depletion of rich and coarse ore reserves and a proportional increase in the mining of low-grade, fine-grained complex ore feeds. This change has resulted in the need for better slime-processing technology. Research and development activities in this area have gained momentum, and recent innovations appear promising. This paper covers the recent innovations that have been made in dealing with tungsten ore slime processing. The new techniques include the application of a centrifugal cone separator, high-intensity wet magnetic separator, the use of phosphonic and arsonic acids as collectors in ultrafine wolframite flotation, and combined processes.

Jan 1, 1989

By Jacek Galas, Stanislaw Lenczowski

The image of the flotation froth surface in the mineral processing plant contains the information about its composition. This information can be very useful for a technological process automation. Images, captured in the optical part of the measurement system were read by the computer, then were transformed and analysed digitally. The set of image parameters, extracted from an image transforms, was evaluated by statistical analysis. The recognition algorithm constructed in this process allowed to estimate the froth composition.

Jan 1, 1995

By Don Cchultz

The United States Forest Service, as a land managing agency, is responsible for the surface administration of National Forest lands. The basic objectives of management are protection and utilization of renewable resources such as water, forage, timber, wildlife, recreation, and clean air. Much of the National Forest land in this country is open to mineral prospecting and development. When large de-posits of minerals are extracted from the forest environment, especially by surface methods, there are oftentimes conflicts between accepted mining methods and the objectives of other resource management goals. Such is the situation in Southeast Idaho where several members of the phosphate industry are operating on and adjacent to the Caribou National Forest. In 1966, the phosphate industry and the Caribou National Forest became mutually concerned with the problems of rehabilitating mined areas and minimizing potential damage to adjacent forest areas. A Cooperative Administrative Study was initiated with industry supporting the Forest Service financially and with equipment, material, and manpower, as well as interest and enthusiasm. The objectives of the study are to provide basic, applicable information pertinent to: 1. Protecting the quality of water emanating from mined water-sheds. 2. Providing for soil stabilization on mined areas. 3. Returning mined areas to surface resource production. 4. The feasibility of making mined areas esthetically acceptable. It was concluded that the following separate--yet intergrated--fields should be studied in order to obtain the desired information:

Jan 1, 1971

By D. A. Dahlstrom

Energy costs have had a serious impact on all basic industries today. This is due to the significant amount of energy that is used to convert natural resources into usable products. Other factors such as transportation with its major energy requirement and materials employed in processing that have already required significant energy input for their manufacture accordingly influence delivered cost to the user. The farmer is a good example of this. While his large capital investment for land, machines, and buildings is highly impacted by today's interest rates, his chemical fertilizer, herbicides, and pesticides as well as those same machines and transportation costs for his products have also been seriously affected by energy costs. With the many unit operations involved in mining and mineral processing, several of which require significant inputs of energy, one can only conclude that this industry has experienced a great increase in percentage of total cost for energy alone. Fuerstenau (1975) indicated that the minerals industry used about 12.5% of the total energy produced in the US. McNulty (1983) listed the total energy requirements for the production of 0.9 t (1 st) of various metals including the energy consumed in the manufacture of supplies employed, such as tires, explosives, chemicals, grinding media, etc. (Table 1).

Jan 1, 1987

By M. Plesha, A. Zubelewicz, K. Connor, T. B. Belytschko, O&apos

INTRODUCTION The Northwestern University Rigid Block Model (NURBM) has been extended to explicitly model dilatant behavior of rock joints. By incorporating dilatancy, the resistance to shear displacement and slip, which previously was limited to simple Coulomb friction, along edge-to- edge contacts is now provided by contact roughness as well as frictional resistance. The explicit formulation is based on concepts presented by Plesha (1985) in which a plasticity-based phenomenological approach was used to model dilatant joint behavior. This approach has been modified to allow for joint closure upon reversal of shear deformation. After presenting a brief description of the new joint constitutive relationship, model behavior will be illustrated with two examples. The first involves a simple two-block model to simulate a cyclic direct shear test of a single joint. The second example involves simulation of a large cavern in a moderately jointed rock mass subjected to cyclic excitation. It will be shown that in- creasing joint roughness increases cavern stability by interlocking of adjacent blocks. JOINT CONSTITUTIVE RELATIONSHIP Within NURBM adjacent two-dimensional rigid blocks interact along their common edge-to-edge contact with contact forces transmitted at the contact midpoint. The contact constitutive relationship was originally restricted to a Coulomb friction yield criterion with no tensile stresses permitted along the smooth contact surfaces. The local coordinate system for any contact is described as shown in Figure 1 with the elastic stresses and displacements related by the linear- elastic constitutive law: [ ] The contact microstructure has been modeled as Patton-type saw-tooth surfaces such as shown in Figure 2. Sliding can be active along the right asperity with angle aR and length lR or along the left asperity with angle a and length lL. In general, aR and aL will difkr as will lR and lL but for purposes of this paper it has been assumed that these angles and lengths are identical. By a simple transformation, the microscopic asperity stresses can be expressed in terms of the macroscopic contact stresses [ ] If Coulomb friction is assumed along the asperity surfaces, the plastic slip condition will be [ ] where µ is the friction coefficient with the convention that compressive stress is negative. When F is negative, the behavior is elastic and when F is zero, slip can ensure. When plastic slipping does occur, it is assumed that the relative tangential and normal displacements between the two contacting rigid blocks are additively composed of recoverable elastic parts and nonrecoverale plastic parts, [ ]

Jan 1, 1986

By Ed Van Eeckhout

The rockburst monitoring system at the Sunshine Mine has recently been improved to increase the certainty of burst locations and to output location results in a manner amenable to easy interpretation. Three methods of location calculation were used: a computer code provided with the hardware in-place (the MP-2501, a code based on the least-squares method (Blake et a1, 19741, and a nonlinear iterative code written by the principal author. The more accurate locations are given by the latter two codes, but still are only correct to within about 100 ft. This error is due to uncertainties introduced by the geologic and mining variations versus the assumptions made in the location codes. Software was then written to make two-dimensional plots of burst location by level, so management could monitor problems easily.

Jan 1, 1986

By F. Heivilin

"Health and Safety problems can make a mineral deposit or a portion of one, an operating plant, or finished product unprofitable or worthless. Therefore they need to be reviewed when reserves are established and yearly thereafter until the deposit is closed down. Health and Safety regulations serve as a guide, but I have always done more frequent checks, when adding new products with different specifications or during times of bad weather and crisis. Water quality and quantity are always in question. Health and Safety are quality of life issues which are at or near the top of priorities for communities, companies, employees, and government bodies. Georgia dropped from one to three in U. S. for business development due to “Quality of Life” issues. Remember crystalline silica is present in nearly all sedimentary and acidic rocks and basic igneous rocks are the perceived home of asbestos. These health issues, any other safety and health issues or perceived issues need to be resolved initially and any time they come up during life of deposit. When handled properly good safety and health programs add to the profitability of a deposit, not to the costs. Daily safety checks in operating plants and mines, and visual check of all drilling core with an eye for changes are a key to successful programs. Both plants I turned around had terrible safety records, too much airborne dust, and maintenance problems resulting in low productivity. In almost every case cost reduction was tied to eliminating maintenance and spillage problems which caused health problems and increased possibility of accidents. Implementation of these safety and health programs around 1970 starting prior to government programs, working with new MSA/MSHA regulations, working to improve the regulations as a president of a state mining organization, and maintain profits was a challenge, but very rewarding. Reducing time to make repairs and work simplification gleaned from observations and employee recommendations learned from making multiple daily inspections resulted in years without lost time accidents at two plants, reduced maintenance and 33-75 % improvement in cost per ton at A. P. Green Refractories Co. Eufaula Calcining Plant 1972-77 and Oil-Dri Ochlocknee plant and mine 1979-82. The Ochlocknee mine worked 1981-2007 without a LTA. The author participated in 16 acquisitions and new plant design projects. All of above reduced costs allowed mining deposits with higher overburden to be used and considered. Thereby increasing reserves considered in all operations."

Jan 1, 2016

By W. J. Bronkala

Dense-medium circuits have been installed in many mineral treatment plants since its, original development about thirty years ago. In the intervening, period the process has been thoroughly evaluated and many innovations have been introduced. The Heavy Density. Cyclone is one of the newer systems which has extended the operating range of this process to 65 mesh size. Several different finely divided materials have been used to produce the separating bath but nearly all new plants use a ferro-magnetic medium. The, advantages of magnetic medium include: 1. Smaller recovery plant 2. Lower cost recovery plant both in initial and operating cost 3. Excellent medium stability 4. Dependable medium supply at reasonable and stable cost. Magnetic separators are used to recover this magnetic medium and the smaller plants and lower operating costs are directly related to their use.

Jan 1, 1964

This paper presents the results of an experimental study undertaken to demonstrate the feasibility of using silica sand as a grinding media in stirred ball mills for ultra-fine coal grinding. Laboratory batch as well as bench scale continuous tests indicate that the use of silica sand can reduce the energy consumption by 50% and more over its steel media counter-part. Moreover, this approach has been found to eliminate the disadvantages observed with grinding using steel media such as high replacement cost, contamination of coal through media wear, greater degree of coal oxidation due to higher slurry temperature and greater level of noise dissipation. Additionally, coal-sand attrition system reduces the manpower time required which is often spent towards cleaning and storing of steel media in inert atmosphere to avoid rust and corrosion problems.

Jan 1, 1991

By Henry T. Miller

INTRODUCTION The basic purpose of this paper is to suggest procedures and practices to insure that no employee working in a uranium milling operation receives exposure to radioactive, toxic, or other materials or agents that might produce a permanent, deleterious effect upon his physical health and well-being. This program is also designed to insure that each employee can carry out his assigned duties without risk to his health or to that of his fellow workers. The assumptions underlying this program are by necessity, conservative, with emphasis being placed upon prevention rather than correction or reaction to an undesirable situation. The limits specified-either as Threshold Limit Values (TLVs), Maximum Permissible Concentrations (MPCs), or Radiation Protection Guides (RPGs)--represent both standards of best practice and those of law and regulation. The total program is envisioned as a balanced combination of occupational hygiene and radiation monitoring. This includes surveying, air sampling, personnel dosimetry, bioassay, medical surveillance, epidemiology, and training--all backed by a thoroughly tested and evaluated set of emergency procedures. The program, as presented, is keyed to the results of monitoring, surveying, air sampling, medical surveillance, and epidemiology--it being obvious that no problem can result when no hazard can be identified. The lack of an identified hazard, however, does not negate the need for such a program and prudence suggests the need for routine surveillance programs in the best-designed facility. [The Model Mill] The model mill used in this paper is that presented by the U. S. Environmental Protection Agency in its study of the uranium fuel cycle1. The model mill processes 600,000 metric tons of ore per year into 1,140 metric tons of U308 as yellowcake per year using an acid leach process. Other characteristics of the mill such as location, tailings dam design, number of light water reactors supported, and geographical location are not pertinent to this paper. The usual remote western location of these facilities produce some difficulties in delivering the required occupational medical services and is not within the scope of this paper. The operating lifetime of most mills is commonly estimated as from 12 to 15 years in actual practice; however, the U. S. Environmental Protection Agency estimated a 20-year lifetime for its model. The principal steps in the acid leach process include :2 (a) Ore is blended and crushed to pass through a 2.5 cm (one inch) screen. The crushed ore is then wet ground in a rod or ball mill and is transferred as a slurry to leaching tanks. (b) The ore is contacted with sulfuric acid solution and an oxidizing reagent to leach uranium from the ore. The product liquor is pumped to the solvent-extraction circuit while the washed residues (tailings) are sent to the tailings pond or pile. (c) Solvent extraction is used to purify and concentrate the uranium. (d) The uranium is precipitated with ammonia and transferred as a slurry. (e) Thickening and centrifuging are used to separate the uranium concentrate from residual liquids. (f) The concentrate is calcined and pulverized. (g) The concentrate or yellowcake is packaged in 208 liter drums for shipment. This process is illustrated in Figure 1.3

Jan 1, 1981

By L. F. Nicolai, W. J. Schlitt

Lateral migration of leach solution in heaps and dumps is attributed to two phenomena. One is site-specific anisotropic conditions that exist on a macroscopic scale on the surface or within the rock piles. The second is associated with a random walk phenomenon that causes dispersion of solution, especially at gradients in flow or hydrostatic pressure. The latter phenomenon is a general condition that will occur in any leaching operation. Its effects are modeled by computer analysis and are compared with available field data on heap leaching. Under appropriate assumptions, the observed 58° angle of solution dispersion can be reproduced by the model. The combined effects of both anisotropy and random walk are also discussed. Finally, the impact of lateral solution flow on actual leaching operations is considered.

Jan 1, 1988