Search Documents

Tables

Jan 1, 1973

By Z. C. Liu, F. F. Roxborough, Lin. B. B.

The size distribution of coal cut by a mining machine is an important performance factor. It is well established that the main machine system variable that affects product size is the depth of cut. In essence, the greater the amount of coal won by a machine cutting at shallow depths, the greater the proportion of dust and fines produced. Conversely, deep cuts produce less dust and a generally larger product size. When cutting with a rotating drum, as well as with a longwall shearer, the depth of cut always varies from zero in the vicinity of the roof and floor, where most of the dust and fines are produced, to a maximum at mid-drum level. In this paper, minimizing the amount of shallow cutting with a cutting drum is discussed, and the effects of the drum cutting and design parameters on cross-sectional cutting area per revolution are analyzed. This study shows the following: •more shallow cutting occurs during the entry quadrant of a cutting cycle than during pick exit; •the ratio of the projected area of shallow cutting to the total projected area of cutting by a single pick per drum revolution is virtually the same for drums of different radii (however, it decreases as the maximum depth of cut increases); and •for double drums, the use of unequal drum diameters can reduce the production of dust and fines, compared to using drums of the same diameter.

Jan 1, 1998

By S. K. Mishra, S. B. Kanungo, D. Biswal

Jigging of the -2.8 +0.7-mm size fraction of a friable, low-grade manganese ore sample from Andhra Pradesh increased the Mn content of a concentrate by 7% to 8%, with an average recovery of 57%. The jig concentrate was mixed with the unjigged -0.7-mm size fraction and ground to -150 µm. The sample was then subjected to wet high-intensity magnetic separation (WHIMS). The magnetic fraction thus obtained showed an increase in Mn content of 6%, but with an overall recovery of only 50%. The results of hydrocyclone classification of -150- µm ground ore indicated that the method is not capable of upgrading the manganese content, as both ferromanganese oxides and aluminosilicate gangue minerals constitute the fine size fraction. However, when the nonmagnetic fraction obtained from the WHIMS of -150- µm ore is subjected to hydrocyclone classification and the underflow obtained is subjected to WHIMS again, an overall recovery of about 50% to 52% is obtained with at least a 7% to 8% increase in the Mn content of the product. The phosphorus content in the product is not reduced by either of the two combinations of methods. The complex association of phosphorus with all the major phases in the ore has been clearly demonstrated from the linear correlation between the distribution ratios of major constituent phases and phosphorus.

Jan 1, 2000

By Richard H. T. Garnett

In 1900, placer gold was discovered on the beach of Nome, AK on the southern coastline of Alaska's Seward Peninsula (Garnett, 1991). The site is about 800 km (500 miles) from Anchorage. Nome is connected to Anchorage only by air (daily) and by sea (summer). Total onshore placer gold production from Nome's immediate vicinity was more than 155.5 t (5 million oz). Alaska Gold Co, has continued to produce gold onshore with, until recently, two bucketladder dredges, each of 255-L (9-cu ft) bucket capacity. Small-scale marine dredging for gold has been at- tempted several times this century (Garnett, 1991). Western Gold Exploration and Mining Co. Ltd. Partnership (WestGold) is the only company to have been successful in achieving a significant offshore production. The Nome bucketladder-dredging operation from 1986 to 1990 constituted a unique marine-mining experience in the United States. \Inspiration Gold Inc., WestGold's predecessor, acquired six offshore leases in 1985. The total lease area of 87 km2 (21,551 acres) extended from the coastline to the 4.8-km (3-mile) offshore limit (Fig. 1). Those leases al- ready had been partially explored. Drilling was conducted off the shorefast winter sea ice. Therefore, it was rarely more than 1.6 km (1 mile) from the shore or in water deeper than about 9 m (30 ft). In 1985, estimated reserves comprised of a 5-m (17-ft) vertical thickness of sediments below 6.3 m (20 ft) of water. This meant a mean digging depth below the mean sea level (msl) of 11.3 m (37 ft). It was thought that the offshore Nome deposit possessed a feature that is common with many terrestrial gold placers - the secret of profitable exploitation of the marine deposit lay in maximizing the dredge throughput to minimize the unit costs. The inability of the project to withstand the prohibitively high cost of a new dredge was recognized. So Inspiration Gold purchased a used unit. This was the world's largest ocean- going bucketladder dredge (Fig. 2). Binzn was an 850-L (30 cu ft) bucket capacity dredge that was lying idle in Singapore. Originally constructed in the Jurong shipyard of Singapore in 1979, Bima was designed by Mining and Transport Engineering, a subsidiary of IHC Holland. Billiton Marine used the dredge for tin production at Pulau Tujuh in Indonesia (Dieperink, 1978) before it was laid up in mid-1985. Bima underwent a nine-week refit before departing Singapore on June 4,1986, with 800-t (880-st ) of deck cargo. It was dry-towed for 32 days to Alaska. A slower, less expensive, wet-tow at the authorized 5.5 kmthr (3 knots/hour) would have delayed the dredge's arrival in Alaska untl almost the onset of winter. The 13,000-km (8,100-mile) voyage was made on the deck of Smit Lloyd's "Giant-4" submersible barge towed by its 7.8- MW (10,500-hp) tugboat. The first season's dredging revealed several major shortcomings in Bima. Further repairs and modifications were undertaken at Tacoma, WA. The dredge returned to Nome for the June start of the 1987 summer dredging season. The refitted Bima worked offshore at Nome from 1987 to 1990. It produced 3.67 t (118,078 oz) of gold at an average recovered grade of 824 mg/m3 (0.0204 oz/cu yd). In 1991, the dredge was dismantled and sold.

Jan 1, 1997

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

"In underground continuous mining operations, ventilation, water sprays, and machine-mounted flooded bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements, such as, face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and equipment operator positioning, can impact the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Office of Mine Safety and Health Research for both remote-controlled continuous mining machine operators and haulage operators at ten U.S. underground mines. Results of these respirable dust surveys show that continuous miner exposures varied little based on depth of cut, but are significantly affected by ventilation configuration. Haulage operators experienced elevated concentrations in blowing face ventilation. The type of cut influenced exposures, with elevated exposures observed for both continuous miner operators and haulage operators when working in crosscuts driven into, or counter to, the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposure attributable to particular mining configurations. These findings form the basis of recommendations for lowering face worker respirable dust exposures when performing a variety of continuous mining cuts.INTRODUCTION Underground continuous coal mining operations may encounter a wide range of conditions and arrangements during production and development activities. These activities typically produce respirable coal mine dust, putting operators of continuous mining machines and coal haulers at risk for elevated exposures. In order to comply with federal regulations limiting respirable dust exposures for the duration of a working shift, mine operators typically implement ventilation, water sprays, and machine-mounted flooded-bed dust collectors (scrubbers) to dilute and control mine dusts during coal cutting. Nevertheless, changes in operational conditions can limit the ability of these controls to effectively reduce dust exposures. Some examples of conditions that can change during the course of mining include face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and operator positioning. Because these arrangements are largely under the control of mine operators, any insight into associated exposures may inform future plans and behaviors, reducing occupational exposures to respirable dust. The objective of this OMSHR study is to evaluate respirable dust exposures associated with a range of continuous mining arrangements by comparing occupational dust concentrations measured during a series of field surveys. These comparisons consider face ventilation configurations, depths of cut, and crosscut mining practices."

Jan 1, 2015

By Werner Burger

The Hallandsås project with a long history, first started in 1991, is well known in the tunneling community. In the past it has been stopped twice for technical and environmental reasons. The third attempt started in 2004 using a dual mode rock TBM. The heterogeneous highly fractured and abrasive rock mass as well as large areas of water bearing zones present most difficult subsurface conditions. The tunneling concept is based on the use of watertight segmental lining and a TBM able to operate in open mode, possibilities for extensive pre excavation grouting and high pressure closed mode operation up to 13 bar to cover exceptional conditions.

By Zhe Liu, Liping Xiao, Jichi Bai, Xuefei Luan

"In order to study the removal efficiency of Cu2+ from acid mine drainage by prepared bentonite-steel slag composite particles, adsorption experiment was carried out. The composite particles were characterized by X-ray Diffraction analysis technique (XRD), Scanning Electron Microscopy (SEM) and Fourier Transform Infrared spectrometer (FTIR). The results show that: the composite particles can release alkali to neutralize the acid of acid mine drainage; the adsorption and chemical precipitation of Cu2+ occurred in the whole reaction process; the removal amount of composite particles on Cu2+ was 9.88 mg/g when the reaction reached equilibrium; the FTIR spectra revealed the existence of surface complexation; the SEM micrographs suggested that the composite particles would continue to adsorb and coagulate Cu2+ after the composite particles surface adsorbing Cu2+ and forming precipitate, namely, there was synergistic reaction of adsorption and coagulation; the XRD patterns further showed the existence of cation exchange and revealed that the states of Cu2+ in the surface of the composite particles was Cu-Si-O mineral phase and CuO(Cu(OH)2) polymerization precipitation. The bentonite-steel slag composite particles which can play a role of adsorption-coagulation synergism are excellent multifunctional green environmental mineral materials to treat acid mine drainage containing heavy metal ions.Introduction It is reported (Zuo and He 2013) that with the rapid development of industry, the world demand for mineral resources is increasing, while the problem of mine environmental pollution is becoming more and more serious due to the large amount of mining. The pollution of mine wastewater has become a global problem, in which acid mine drainage (AMD) is one of the most serious waste water. It is also reported (Cong and Zhao 2003) that acid mine drainage containing high concentrations of heavy metals and having low pH value, causing serious negative influence to the mining production and ecological environment. Acid mine drainage is one of the most serious environmental pollution to the mining industry. In recent years, it has been widely concerned by scholars at home and abroad."

Jan 1, 2017

By Robert C. Meaders

In this paper, autogenous grinding is defined as the combined crushing and grinder of a run-of-mine ore or the product from a primary crusher, in a single stage grinding mill. This is in contrast to pebble milling where pebbles are substituted for steel balls to grind a ball mill size feed. The autogenous mill to compete in efficiency with normal methods of crushing and grinding must not use greater power, must use less labor and steel, and must produce an equivalent product.

Jan 1, 1963

By J. Wickens

This paper discusses how Bald Mountain Mine dramatically reduced mercury production by treating process solutions with a liquid reagent called UNR 811A. The reagent is marketed by Cherokee Chemical Co., Inc. A summary of the bench tests comparing several different reagents is given. The ensuing plant trial is discussed and results are presented. The plant trial treatment costs are discussed. Finally, potential cost savings are discussed.

Jan 1, 2001

By Missy Isaman

"Mixed ground tunnels come in all kinds. In rock tunnels with possible faults and high pressure water, the challenges are many. With the advent of Crossover TBMs, contractors can minimize machine wear in such conditions while maximizing efficiency. The newest generation of Crossover is exemplified by two projects in Albania and Turkey. A 5.56 m Crossover TBM destined for Turkey’s Gerede Water Transmission will be assembled using Onsite First Time Assembly (OFTA) from within an existing tunnel. The unique machine will bore through 30 fault zones requiring the TBM to be sealable to up to 20 bar so pre-consolidation grouting can be done. If boring under pressure is required, the TBM will bore sequentially using the screw conveyor fore and aft gates. Skewing further towards hard rock, a unique 6.2 m diameter Double Shield TBM with Crossover features was designed for Albania’s Moglicë Headrace Tunnel. The machine features closure doors and a sealing system to contain inrushes of water until they can be grouted off. This paper will discuss the unique aspects of the Crossover designs, including their inception as based on past projects in difficult ground, and their utilization at the two current projects. INTRODUCTION Specialized tunnel boring machines have been made for years to tackle specific types of ground conditions. Traditional types of TBMs bore within a specific set of ground conditions. If a project is located in a competent granite face, then a Main Beam machine is a good solution. In soft ground, Earth Pressure Balance (EPB) machines are the method of choice. Years of experience and engineering advancements have made both types of machines fast and economical solutions for tunneling. Unfortunately not all ground conditions are a perfect swath of one material, and the need for a more diverse machine is apparent."

Jan 1, 2016

There is wide agreement that sustainability has multiple dimensions, but substantially less agreement on the appropriate balance among those dimensions. This occurs because peoples’ vision of a sustainable future, their goals for sustainable development, and their objectives for resource management are reflections of their values, culture, and life experiences. Even assuming agreement about the objectives of sustainable resource management can be reached; there is still a need for policy and decision makers to choose from among alternative courses of action, each of which has its own set of impacts and outcomes. One of several tools used to compare the consequences of alternative actions is the Computable General Equilibrium (CGE) model. This paper uses CGE modeling to demonstrate how policy decisions do not take place in a vacuum and how policy-makers must be aware that there are trade-offs involved in any decision.

Jan 1, 2005

By Randal J. Barnes

Computer based techniques for solving the Ultimate Pit Limit Problem have appeared in mining literature since the early 1960's. The majority of papers pertaining to this subject can be partitioned into one of two categories: discussion of the pros and cons of a particular algorithm, or a case study presenting specific applications of an algorithm. Subsequently, there has a1 so been considerable debate concerning the best techniques between, essentially, two camps: those favoring the moving cones techniques, and those favoring the techniques which yield true optimal pit designs. The purpose of this paper is not to add to this debate, but rather to present a few new ideas (partially a new look at an old idea), which can be easily implemented to noticeably improve any ultimate pit limit approach independent of the particular algorithm used. These ideas fall under the heading of "bounding the optimum" (Barnes and Johnson, 1980).

Jan 1, 1982

By Robert L. Grayson

An application of goal programming (GP) in evaluation of proposed purchases of major mining machinery is presented. It incorporates historical operating data compiled on mechanical delays to production time. The goal programming technique, which is an extension of integer programming, is used to maximize an objective function. The objective function combines the capital budgeting evaluation methods of net present value, payback period, profitability index, and total net earnings as goals weighted according to a management preference. The GP method gives an optimal solution to a multiple-goal problem. A sensitivity analysis is performed to determine the effect of an increased production forecast or a tightened budget on proposal selection.

Jan 1, 1982

By M. Rieber

In July 1985, as the U.S. copper industry contracted and the Mexican industry expanded, a trans border pollution agreement was signed which included smelter air pollution control in the "Gray Triangle": Cananea, Nacozari and Douglas. Since then the Douglas smelter has been closed, a year earlier than initially required; though its new smelter is operating, S02 collection and acid disposal at Nacozari is yet to come; and the Cananea smelter has been un-touched. Nacozari and Cananea copper mining have expanded while a reduced U.S. copper industry has rationalized to a point of fragile profitability. As a paradigm of U.S. copper competitiveness, this paper attempts to explain the differential fortunes of copper in the two countries, to project the future of the smelter agreement as a function of acid disposal, and to consider the consequences of the politicized application of smelter pollution control in Arizona.

Jan 1, 1988

In the UK as existing face capacity is replaced, many of the new faces will have higher installed powers and be located in zones of higher strata temperature. These factors coupled with the need to increase production will result in more faces experiencing environmental difficulies, especially with respect to climatic conditions. In many cases these problems are unlikely to be solved, as in the past, by simply increasing the face air quantity. Therefore other techniques including refrigeration will be necessary, possibly requiring major capital and operational expenditure. It is easy to spend large capital sums and incur high operational expenditure without achieving the desired amount of climatic control. There is therefore a great need for reliable prediction techniques to aid in the making of sound, informed decisions which will have a significant influence in the long term on the level of production costs. A computer program able to predict the heat flows and resultant climatic conditions on a long¬wall coalfaces has been developed. Throughout it's development underground measurements have been used to validate the computer model and it has been shown that for an advancing coalface under normal production conditions that the program predicts the climate to within 1°C of the measured conditions. This paper outlines a number of methods available to improve climatic conditions on longwall faces. The coalface temperature prediction program is used to quantify the effects of these methods on the climatic conditions for a model coalface and a comparison is given. In conclusion a cool¬ing strategy for longwall faces is outlined.

Jan 1, 1991

By Levent Ozdemir

An extensive study involving laboratory testing and computer modeling has been performed to assess the technical and economic feasibility of utilizing the recently developed minidisc cutters on roadheaders for hard rock mining. The results show that heavy duty roadheaders fitted with minidiscs can excavate hard rock formations at acceptable production rates and cutter costs. This paper presents and discusses the results of this study together with the ongoing developmental efforts of this technology, which include laboratory testing of a roadheader cutting drum with minidiscs and full scale field testing of a machine in hard rock

Jan 1, 1995

By Fred A. Breu, Jerome C. Neyer, James F. Peters, John W. Critchfield

This paper describes experiences with methane and hydrogen sulfide gas encountered during design and construction of a sewer tunnel in rock, in Rochester, N.Y. Design explorations are summarized, including geologic setting, measurements of gasses in test borings, laboratory analyses of gas samples, and measurements of gas pressure and flow rates from a sealed borehole. Contract specifications regarding gas are outlined. Results of the Contractor's additional explorations and testing are presented, along with a description of selected equipment and provisions for ventilation and degassification.

Jan 1, 1985

By V. G. Hill

The term bauxite was first used by O.P.A.P. Dufrenoy in 1845 for an ore which was discovered by Pierre Berthier in 1821 near the village of Les Beaux de Provence near Arles in southern France. His data suggested that this mineral was an alumina hydrate with two molecules of water. However, it was subsequently shown by thermal analysis that the mineral was a fortuitous mixture of the mono-hydrate and the tri-hydrate. Diaspore had been previously discovered in 1801 and gibbsite in 1822. The term was however retained as a rock name. The name of the village was changed to Les Baux around 1885; Sainte Claire Deville suggested that the mineral name should reflect this, and it was changed to bauxite (Bracewell, 1962, Rkgnier, 1988). Mining of bauxite began around 1860 in the Auriol region in the Bouches du Rhine area in the south of France. This ore was transported toMarseilles by carts and was processed in the Salindres plant, which at that time was the only plant producing alumina using the Deville process and aluminum by the chemical process. During that period white bauxite (low iron content) was particularly sought after for the production of aluminum sulfate, refractory bricks, and quick setting cement. Export of bauxite from France began in 1880 and was initially delivered to Chemische Fabrik, Goldschmischen near Breslau, and to Guilini's Ludwigshafen plant in Germany in 1885. These companies produced alum and aluminum sulfate (RCg- nier, 1988). The next bauxite mining operation was in Antrim County in Northern Ireland in 1873. This was first used for the manufacture of alumina refractory bricks and quick setting cement (Bracewell, 1962). It is important to emphasize that initially almost all of the bauxite which was produced came from France and was mainly used for non-metallurgical purposes. At that time even the production of alumina was mainly for use as a mordant in textile dying. However, with the development of the Hall-Héroult process, the alumina which was available was increasingly used for smelting to aluminum. In spite of this the demand for non-metallurgical bauxite continued to increase and a set of applications were developed. These include refractories, abrasives (including the recently developed proppants), high alumina cements, aluminum chemicals, activated bauxite, and alumina. It became increasingly evident that the high alumina-low alkali raw materials have special advantages. The question however was one of cost benefit. Chin (1989) has pointed out that the non-metallurgical operations have been traditionally grafted on a bauxite/alumina/aluminum industry tree. In this context the non-metallurgical alumina produced was, with few exceptions, regarded as either coproduct or byproduct i.e.: Bauxite Trunk Sector Alumina Trunk Sector Aluminum Trunk Sector

Jan 1, 1994

By N. Duru

"Gravity concentration is still a challenging area in the mineral industry. This is mainly because of the fine size valuable mineral losses to the tailings during its application. But the recent developments in centrifugal separation methods and their mutual application with conventional separation techniques has increased mineral recoveries. In this paper, field application of conventional gravity separation methods with the combination of 2” diameter hydrocyclone cluster unit and a multi gravity separator (MGS) was discussed. Additionally, particle size distribution and chromite content of the plant streams is presented and initial laboratory test results were compared with the actual plant data throughout the paper. As expected, field data showed derivations from the laboratory tests but the combination of MGS and conventional gravity separation techniques resulted in gravity separation of -0.1 mm chromite particles. INTRODUCTION The purpose of this mineral processing plant project was to investigate the possibility of upgrading chromite ore from 12% to 48% Cr2O3 and having final tailings assay as 2% Cr2O3. For this reason, initially a set of laboratory gravity separation studies were conducted to evaluate the performance of combination of 2” diameter hydrocyclone cluster and multigravity separator. After obtaining successful results from the laboratory work, a feasibility study was initiated. Economical results of the feasibility study showed that an achievable high net present and return on investment values. Following the investment decision; engineering, equipment procurement, construction of the processing plant was completed in eighteen months. This paper focuses on the initial laboratory test work results, operational data of the 2” diameter hydrocyclones and MGS units; resulted chromite recoveries. Processed ore has the chromite associated with serpentine and olivine minerals. The chromite particles are generally in round shapes with sizes between 50 µm to 1600 µm and average size of 450 µm. The microscope images of the chromite and associated formations are presented on Figure 1.Chromite is formed in mixture with iron oxides, with varying amounts of magnesium, aluminum. The average chemical composition of the representative drill core samples of the ore deposit is given on Table 1."

Jan 1, 2017

By J. Mastoris

The growing environmental awareness and the need for providing social service to the community, urge the primary sector companies (such as mining) to find new solutions, by adjusting their operations with the special, local conditions and meeting everyday problems in practical ways. We hereby present a real case of re-design of an open pit, closed-bench type industrial minerals (clay) excavation, for the purpose of rehabilitation and utilisation as a water reservoir. The potential use of rainfall water was studied on the basis of covering the irrigation needs and improving the living standard of the neighbouring farmers and also as a project or recreational development of the area by shaping a wetland. The experience from the project progress and the reservoir use has been positive to date and the reclamation plan seems to have the acceptance of the local community.

Jan 1, 2002