Search Documents

By N. Hoffman

Accurate, repeatable density measurements of a coal-magnetite-water slurry are difficult to achieve using a nuclear density gauge. Changes in the coal-to-magnetite solids ratio cause fluctuations in the readings of nuclear gauges. To investigate this problem the Electric Power Research Institute's Coal Cleaning Test Facility compared the performance of a nuclear density gauge on a coal-magnetite-water slurry with the performance of a differential pressure gauge modified with a new pressure sensor. A second aim of these preliminary tests was to determine if the differential pressure gauge is also sensitive to the type of solids in the slurry. This paper explains current slurry density measurement practices, describes the nuclear and differential pressure gauges used in the CCTF tests, and presents test methods and results.

Jan 1, 1986

By R. Q. Honaker

Dense medium processes are used to clean over 50% of the coal that is fed into preparation plant facilities worldwide. The dense medium is formed using ultrafine magnetite which is recovered after the cleaning step using drain-and-rinse screens and magnetic separators. Despite the high efficiency of the recovery system, magnetite losses of around 0.5 to 1.0 kg/ton are common. Considering the recent escalation of magnetite to around $300/ton, an alternative source of magnetic material from coal combustion bottom ash has been investigated. A relatively low cost recovery system has been developed. Dense-medium tests using the bottom ash magnetics revealed a high level of efficiency as indicated by probable error values around 0.03 over the range of medium densities investigated. The results from both the recovery and coal cleaning efforts will be discussed in detail.

Jan 1, 2009

By M. E. Rossi

Reconciliation of long-term, block-model reserves and mine production frequently shows significant discrepancies. This reconciliation can be done comparing the long-term, block-model reserves against a grade control model (a model based on blast holes or production data). In this article, this is called an Fl factor for tonnages, grade and ounces. This reconciliation should also be done by comparing the grade control model to the mill feed (or loaded to heaps) tonnages, grades and ounces (F2 factor). The long-term model usually contains blocks with dimensions larger than the size of the selective mining unit (SMU) of the operation. The smoothing effect of an estimator, such as kriging, will generally result in a grade-tonnage curve that does not match the grade-tonnage curve of the SMUs to be recovered. This problem is partly to blame for the reconciliation discrepancies found. In addition, in-pit perfect selection is impossible. Therefore, the grade-tonnage predictions based on blastholes also need to be assessed - considering unplanned dilution and the errors of estimation of the grade control model. This article focuses on using conditional simulations to assess the uncertainty of the predicted grade-tonnage curve in terms of minable reserves and in the framework of long-term mine planning. Quantifying the uncertainty in no uncertain terms is done in conjunction with a popular pit optimizer. It yields several possible minable reserves and several possible minable tonnages and grades, per pit shell or scheduled phase. This is a step further from the usual sensitivity analyses that are performed for deposit evaluation or development planning. Specifically, this approach takes into account the volume-variance relationship, the selectivity of the mining operation and the planned and unplanned dilution. It also carries the local uncertainty implicit in grade estimation into the mine design and mine planning phases. The estimation of recoverable reserves revolves around estimating the block distribution of metal grades from the drill hole information available, typically composites of a fixed length. Ideally, this estimation should accurately predict the ore sent to the processing facilities of an operation. Here are some definitions used in this article: ? Recoverable reserves are those where an attempt has been made to estimate the actual distribution of grades (usually by a block model) that would be found in the ground at the time of mining, relative to the mine equipment size and other operational characteristics of the mine SMU. In particular, it incorporates the effect of internal dilution for each block how the grade distribution changes in variability when comparing a composite grade distribution to the "mining unit" grade distribution. In geostatistical jargon, this is known as "change of support effect," or volume-variance effect. ? Minable reserves are those recoverable reserves defined by a mine plan. In an open-pit scenario, they would incorporate pit optimization in addition to the sequencing and scheduling of production through mine life. ? All other block model estimates from drill hole data that do not explicitly attempt to estimate or measure the volume-variance effect are called in situ. It can be argued that these models may be inappropriate tools for predicting the grade-tonnage curve of the material to be sent for processing (minable reserves). The purpose of estimating recoverable reserves can be thought of as estimating the appropriate amount of dilution that should be incorporated into the model so that it adequately predicts (long-term and on average) the grade-tonnage curve of the ore sent to the processing facilities (mean grades and ton-

Jan 1, 1999

By Mitchell J. Willis

Recovery of fine particles has been considered to be a major limitation of the classical flotation process. However, the beneficiation of kaolin, a naturally occurring fine ore, via flotation has been practiced over the last 40 years. Kaolin is valued as a white pigment, and therefore, the goal in kaolin flotation circuits is to remove the colored impurities to result in an acceptable brightness product. Kaolin flotation originated with a novel carrier flotation process, and later on carrier less flotation techniques were developed. The collector chemistry utilized to beneficiate kaolin is based on fatty acids, and recently hydroxamates have been successfully used. The purpose of this paper is to cover the flotation practice in the kaolin industry in terms of the history and the reagent schemes.

Jan 1, 1999

By B. T. Dawson

In today's work world, constant changes are a fact of life. Downsizing and technological advances are two of the most prominent concerns for employers and employees alike. In this article, the author addresses some of the emotional consequences of these changes and offers a new, empowering perspective for coping with them.

Jan 1, 1998

This study was conducted to establish the effects of a diesel particulate filter (DPF) system with sintered metal substrate on the concentrations and size distributions of nano and ultrafine aerosols and concentrations of nitric oxides in underground mine air. The study focused on the formation and transformation of nucleation mode particles in mine air under prevailing test conditions. Experimental work was conducted in the NIOSH Diesel Laboratory at the Lake Lynn Laboratory experimental mine, a facility developed to allow evaluation of control technologies directly in underground conditions. The DPF system was examined for four repeatable steady-state engine modes using a naturally aspirated mechanically controlled Isuzu C240 diesel engine fueled with ultralow sulfur fuel. The engine coupled to an eddy-current dynamometer was operated in the underground drift with tightly controlled ventilation. Measurements upwind and downwind of the exhaust system discharge were used to quantify the effects of the DPF system on the mine air. A baseline was established using a standard muffler. The study showed that sintered metal DPF systems reduced the total mass of aerosols in the mine air by more than ten-fold when compared to a muffler. The nucleation mode aerosols (50dem<40 nm) in mine air were found to be strongly influenced by engine operating mode. The concentration of nucleation mode aerosols was found to be significantly higher for high-load modes than for low-load modes. The muffler and DPF system resulted in comparable total nitrogen oxides (NOx) concentrations. However, the nitrogen dioxide (NO2) fraction of the total NOx was found to be substantially higher for both systems for low-load modes than for high-load modes.

Jan 1, 2009

By D. Brosnahan, J. Gathje

Newmont Metallurgical Services (NMS) recently acquired a Scanning Electron Microscope (SEM) with a JKMRC/FEI Mineral Liberation Analyzer (MLA). With the MLA software package, raw particle image and X-ray data can be converted into particle mineral maps and bulk and liberation data can then be calculated for minerals of interest. This type of quantitative mineralogical data can then be used for a wide variety of applications. Ore characterization with MLA can be carried out for existing or processing plants in development. MLA characterization of laboratory test products provides valuable liberation information that assists the research metallurgist in better planning and developing process treatment options for various ore types. This paper describes the use of MLA characterization in a copper flotation test program where the use of various testing options for arsenic depression was being evaluated.

Jan 1, 2007

Acid mine drainage (AMD) forms when sulfide minerals are exposed to oxidizing conditions in coal and metal mining, highway construction, and other large-scale excavations. Iron sulfides common in coal regions are predominately pyrite and marcasite (FeS2), but other metals may be complexed with sulfides forming chalcopyrite (CuFeS2), covellite (CuS), galena (PbS), and sphalerite (ZnS). Pyrite commonly occurs with these other metal sulfides thereby causing AMD where Cu, Pb, and Zn are mined. Upon exposure to water and oxygen, sulfide minerals oxidize to form acidic, sulfate-rich drainage. Metal concentrations in AMD depend on the type and quantity of sulfide minerals present. The drainage quality emanating from underground mines or backfills of surface mines is dependent on the acid-producing (sulfide) and alkaline (carbonate) minerals contained in the disturbed rock. In general, sulfide-rich and carbonate-poor materials produce acidic drainage. In contrast, alkaline-rich materials, even with significant sulfide concentrations, often produce alkaline conditions in water. Approximately 20,000 km of streams and rivers in the United States are degraded by AMD. About 90% of the AMD reaching streams originates in abandoned surface and deep mines. Since no company or individual claims responsibility for reclaiming abandoned mine lands (AML), no treatment of the AMD occurs and continual contamination of surface and groundwater resources results. The oxidation of iron disulfides and the generation of acidity occur through several reactions (Stumm and Morgan, 1970). The chemical equations can be found in Caruccio and Geidel (2000). If any of the processes represented by the equations were slowed or altogether stopped, the generation of AMD would also slow or cease. The equations show that 1000 Mg of rock containing 1% sulfur, all as pyrite, would yield upon complete reaction 31.25 Mg of acidity. Therefore, 31.25 Mg of 100% CaCO3 would be required to neutralize the acidity. The alkaline content of overburden determines whether there is enough neutralization potential (NP) to counteract the acid produced from pyrite oxidation. Of the many types of alkaline compounds present in rocks, only carbonates and clays occur in sufficient quantity to effectively neutalize AMD. A balance between the acid-producing potential and neutralizing capacity of an overburden sample will indicate the ultimate acidity or alkalinity that might be expected in the material upon complete weathering. Accurate prediction and control of AMD before surface mining require an understanding of three important factors: 1) overburden geochemistry, 2) method and precision of overburden handling and placement in the backfill during reclamation, and 3) the postmining hydrology of the site.

Jan 1, 2002

By J. P. P. Silva

Sodium silicate (water glass) is a modifier reagent widely used in flotation with the function of a depressant or dispersant. The interaction between sodium silicate and mineral surfaces is still not well understood. This investigation aimed to illuminate the sodium silicate action mechanism as a depressant in the flotation of the minerals quartz and calcite. The experiments were done with high-purity mineral samples in the particle size range below 147 µm. The microflotation tests in a modified Hallimond tube showed that, in all systems tested, the efficiency of sodium silicate increased with the concentration. At concentrations above 1,500 g/t, almost total depression (96% for calcite and 97% for quartz) was achieved. The variation of sodium silicate modulus did not alter the quartz flotation performance in the presence of amine (150 g/t). The most efficient depression pH range was observed between 5 and 8. Above pH 10, the depressant action of sodium silicate was negligible. The infrared spectra obtained at pH 7 after silicate contact showed the presence of the groups OH and Si-OH, both suggesting that the adsorption of the neutral species Si(OH)4, as well as siloxane groups (Si-O-Si), attributed to adsorption of polymeric species. Sharing electron pairs is the proposed adsorption mechanism between Si(OH)4 and polymeric species and the surface sites (Si-O on quartz and Ca-O on calcite). At pH 11, the electrostatic repulsion prevents the species adsorption, impairing the sodium silicate action.

By I. J. Jansen

Successful soil construction involves preparation of an adequate base, selection of high quality soil materials, and placement of those materials by means which will establish a continuous macropore network and modest to low soil strength. Where such has been accomplished, experiments reveal row crop productivity on reclaimed land which is very competitive with that on undisturbed land. Inferior productivity and sensitivity to drought stress are experienced where the soils are excessively compacted during construction. Some deep tillage practices have been quite successful in improving the compacted soils, but it is preferable to avoid compaction as the soil materials are handled.

Jan 1, 1987

By H. Lind

The consumption rate of Estonian oil shale increases due to the growing rate of exported oil-shale oil. Estonian oil shale active resources in working mines are predicted until the year of 2025 when the consumption rate stays at the level of 12 tons per year. If the consumption rate stays at that level, new mines should be opened after 20 years, if the rate increases new mines should be opened even earlier. The predicted active resources in Estonian oil shale deposits are calculated for 60 years, based on the parameters of the power station technicoeconomics. As a result, there is a need to open new mines. One of the potential areas for surface mine is the Tammiku-Kose prospect area (Rheinbaun Engineering, 1996).

Jan 1, 2006

By D. C. Torre

The coal mining industry has long recognized the need for a system capable of hauling mined coal from the face in a continuous flow. More than 30 years ago, successfully operating continuous haulage systems were first placed in the field. There were a few individually successful applications. However, the truly successful use of such systems really only began in the early seventies. Today, a variety of systems are available from a number of manufacturers. Even so, continuous haulage has not achieved the acceptance and application it would seem to have earned. There is a need for more productive, cost-effective, and safer methods of hauling coal from the face. There is also a need to speed up development for longwall operations. And continuous mining is not really "continuous" unless it is supported by a reliable continuous haulage system. Despite all this, most of the coal producers have failed to exploit the successful continuous haulage systems offered by several manufacturers. In the 1970s, many of the top coal producers tried a continuous haulage system but gave up on it and on the concept. In some cases, major coal companies had systems operating successfully in one mine, or even one division. But their use did not spread to others of their mines or divisions. Frequently, their use was eventually abandoned, even in mines where it had been successful.

Jan 1, 1990

By David A. Fawcett

An auxiliary cross-pit mining system, working in tandem with the prime excavator, is evaluated technically, operationally and economically for application in the selective removal and replacement of soils and unconsolidated ovezburden. Previous studies on cross-pit technology and applications of this technology are briefly reviewed. Stratigraphy plus pit, operating and economic parameters are assumed and applied in the evaluation and comparison of a base case dragline system with two alternatives - a dragline/scraper-dozer combination and a drag- line/cross-pit system combination. The economics of the proposed cross-pit system favour it as a viable alternative to conventional systems.

Jan 1, 1981

By Ralf Winterberg, Axel G. Nitschke

"Macro synthetic fiber reinforced concrete or shotcrete is seen by many design engineers as offering a viable alternative to steel reinforcement in tunnel linings. The technology is now commonplace for primary and permanent ground support in both mining and civil tunnel applications. It has for instance become the standard form of reinforcement in the Australian mining industry, and has been used for a majority of permanent tunnel linings in recent tunnel construction in Norway. Similarly, macro synthetic fibers are becoming a standard solution for the initial lining in the USA.The use of macro synthetic fiber offers innovative solutions, yielding robust and sustainable tunnel lining designs. Citing recent research and actual projects, this paper presents state-of-the-art design considerations for fiber reinforced tunnel linings relating to structural and long-term performance. Topics include seismic resistance, crack width control, corrosion and durability, as well as sustainment of performance with age.INTRODUCTIONMacro synthetic fiber reinforced concrete (MSFRC) and shotcrete (MSFRS) has reached maturity as an engineered material and is widely used in all forms of tunnel linings, for temporary as well as permanent ground support in both, mining and civil tunnel applications. In the Australian underground mining industry, it became the standard form of reinforcement, where 2014 literally marked the end of steel fiber use in shotcrete [1], and has been used for over 80 percent of permanent tunnel linings in recent tunnel construction in Norway. Similarly, macro synthetic fibers are becoming a standard solution for tunnel initial linings in the USA. Recent examples in civil tunneling are the Devil’s Slide Tunnel and Caldecott Fourth Bore Tunnel in California or the Anacostia River Tunnel Intershaft Connector Tunnel in Washington D.C. In addition, an increasing number of tunnels are adopting shotcrete permanent linings using macro synthetic fibers. Examples include the A3 Hindhead tunnel near Guildford in the UK and the North Strathfield Rail Underpass in Sydney, Australia [2, 3]."

Jan 1, 2016

By Bruce W. Cavender

In an effort to lower production costs and improve profitability, mining companies have adopted a variety of management practices emphasizing productivity and cost containment. One set of practices that has been used successfully in the manufacturing and electronics industries is "world-class manufacturing" (WCM). It is applicable to mining as well. World-class manufacturing is based on the twin concepts of "just-in-time" inventory practices and total quality control. A few mining companies have implemented quality control programs that are similar to WCM in some ways and substantially different in others. This article considers the use of WCM in the processing environment, although the techniques are applicable throughout a mining operation. The article is also mindful of the variety of customers to whom mineral products are sold. Industrial minerals producers may sell brand-name products to specific customers with exacting requirements, while metals producers often sell their fungible output on a faceless commodity market. Customer requirements are emphasized in WCM, and so the range of these requirements must be recognized. World-class manufacturing In any milling process, specific goals are set for product and process characteristics - concentrate grades, minimum daily throughput, moisture content, etc. WCM has two overriding objectives: the reduction of deviation from these standards, and the reduction of variability in all aspects of the process and product. By definition, reduction of deviation also includes minimizing plant downtime for repairs or process changes. WCM plants use just-in-time inventory practices and total quality control. WCM plants use these techniques to simultaneously improve productivity and reduce costs.

Jan 1, 1993

By G. Vijaya Kumar, B. Srinivasa Rao, G. V. Krishna Rao

The paper outlines the ventilation practices prevailing in coal mines of Singareni Collieries Company (South India). The high annual average surface temperature and relatively steep geothermic gradient results in virgin strata temperatures in the region of 38- 42°C creating environmental problems in the working places. Expensive methods of air cooling can not be employed as the mines are small, and production and productivity do not justify the costs of artificial cooling of mine air. Controlled recirculation of mine air -- the unconventional technique being tried with success in some coal mines in U.K. has been analysed for improving the environmental conditions. The analysis shows that the method is safe, cost effective and can be applied with very little extra equipment.

Jan 1, 1991

By E. DeLilia

For the past 30 years, surface mines have moved toward more highly mechanized, automatic systems that continuously mine overburden and ore to in-crease productivity, lower operating costs and minimize manpower needs. To achieve these goals, mine operators must be involved in every step of the machine procurement process. Several factors are involved in making the machines operate economically and efficiently: ? Prudent engineering. ? Proper planning. ? Realistic feasibility studies. ? Effective specification. ? Thorough training of the mine personnel.

Jan 1, 1995

By J. M. Gambogi

Demand for titanium minerals and pigments was nearly unchanged in 1996 compared with 1995. However, through mine expansions and process optimization by the TiO, pigment industry, the available supply of titanium minerals and pigments increased moderately. At the end of 1996, exploration, development and expansion programs were ongoing in the mining sector. But expansion projects in the pigment sector were delayed pending increased demand.

Jan 1, 1997

By Yngve Jordal, Sverker Hartwig

The IVAR Project is Norway&apos;s largest sewer project presently under construction. One part of it is an 8.1 km (26 575 ft) long, 3.5 m (11 ft 6 in.) diam tunnel, bored in one year. The tunneling project has been running smoothly; however, not everything has been easy. A few of its features are highlighted in this paper: The use of 9 0 (12 cu yd) muck cars on a double track back-up in such a comparatively narrow tunnel. Employing only four men in the tunnel, including the loco driver. A quartzite dyke - 96% quartz with 350 MPa (50 000 psi) and more compressive strength - turned out to be 640 m (2 100 ft) thick instead of the predicted 90 m (300 ft). Passing under a gaseous swamp with only same 5 m (16 ft 5 in.) of rock cover on top.

Jan 1, 1991

By Michael J. Pyrcz, Clayton V. Deutsch

Strategic project decisions are based on the distributions global variables, for example, total mineable resource, or recoverable oil volume. These global variables distributions are very sensitive to the input one point statistic, that is, histogram and rock type proportions. Representivity in the one point statistic retains significance in all spatial models. Spatial sampling bias and nonrepresentative sampling complicate this process of building representative one point statistics. This work outlines the cause of bias, the inability of standard declustering to correct for this bias and two methods for correcting bias in the one point statistics: "trend modeling for debiasing" and "debiasing by qualitative data". An example is presented of each technique based on a poly metallic data set.

Jan 1, 2002