Search Documents

By N. D. Jagger, I. M. Arbuthnot

Introduction Over the last five years, a large number of small- to medium-sized carbon-in-pulp treatment plants have been built in Australia, most designed to treat between 250,000 t/a and 1.5 Mt/a of ore. Because of the limited capital resources and tight cash-flow positions of these relatively small mining companies, the primary requirement was often to get a plant built and operating in a short period of time and at minimal capital cost. Therefore, since the inclusion of both pre-leach and tailings thickeners represents an obvious and significant capital cost, most of these plants were built without thickeners or even detailed, cost-benefit analyses on their inclusion. In some cases, the increasing use of High Rate Thickeners (HRTs) in the mineral processing industries has, however, resulted in a reassessment, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas where borefields are costly to install and water is limited. With the startup and operation of these installations, the resulting significant savings in cyanide consumption has been recognized, in many situations, as a primary justification for the installation of HRTs. Solution balances Degradation of cyanide occurs in the tailings water discharge to slime dams. The degree of degradation (cyanide loss) in the water recovered depends on a number of factors, but it is usually assumed to be about 90%. The most important mechanisms of CN loss are through HCN losses and oxidation by oxygen in the air, which also assists in the hydrolysis of CN. These mechanisms are supported by the large dam surface area and the long retention time of the tailings water in the dam. By thickening the CIP tailings at the plant and recovering as much tailings water as immediately possible, these losses are avoided. The retention time in an HRT is less than three hours, and the surface area is relatively small. Therefore, CN losses are negligible, which is not necessarily the case in conventionally-sized thickeners. Fig. I shows a block diagram of a 100-t/h gold plant without a thickener. In this example, 50% of the tailings water pumped to the tailings dam is recovered, and the CN concentration of the returned water is 10% of the tailings CN concentration of 150 ppm. Fig. 2 represents a plant with an HRT on tailings, thickening to 55% w/w solids. In this case, the thickened tailings are pumped to the dam, and 25% of the contained water is recovered. The recovered water and the mill make-up water are not sent directly to the mill; instead, they are added to the thickener feed and mixed with it prior to thickening. By doing this, the tailings are effectively washed, and the additional cyanide is recovered. Solution balances over these two circuits show cyanide recoveries of 5% and 65%, respectively. Thus, the thickener use increases cyanide recovery by 60%. Fig. 3 shows a two-stage HRT circuit in a countercurrent decantation (CCD) configuration. In this example, an additional 13% of cyanide is recovered through the use of the second-stage unit. This configuration can be justified when residual cyanide levels are high. Capital and operating costs - Case study 1 Illustrative cost figures are based on a CIP tailings thickener installed, in early 1988, as part of Dominion Mining's treatment plant at Paddy's Flat near Meekatharra. (All costs within this paper, unless stated otherwise, are in Australian dollars.) [Assumptions: Feed rate 150 t/h Ore moisture content 5% Leach density 40% solids Underflow density 55% solids Residual cyanide in tailings 150 g/m3 Flocculant dosage 15 g/t Consumable costs: Water $ 0.40/m3 Cyanide$ 2.00/kg Flocculant$ 4.50/kg Power$ 0.12/kWh Length of tailings pipeline2,500 m Capital costs of the major items involved in the thickener installation are given below: Thickener unit, 15-m diam $ 230,000 Water return pumps 12,000 Water recirculation pumps 28,000 Feed box 5,000 Flocculant make-up system 18,000 Flocculant storage tank and dosing pumps 11,000 Piping and valves 85,000 Electrics and instruments 47,000 Civil works 29,000 Installation 69,000 Total cost$ 534,000] Savings in capital costs that can be attributed to the

Jan 1, 1993

By A. J. Monhemius, R. G. Reddy, G. W. Warren, E. Peters

Thermodynamic solubility of chromium in pickling solutions (i.e., HF- HN03-H2O solutions) was determined as a function of HF and HNO3 acid concentrations at 298K. Pure Cr, AISI type 316 and 416 stainless steel were used in this study. The results showed that the solubility of Cr increased with increase in the concentrations of HF and HNO3 acids in solutions. The solubility of Cr increased in the order of pure Cr > 416 SS > 316 SS. The theoretically calculated Cr solubility data were in reasonable agreement with the experimental data.

Jan 1, 1993

By Clinton Strachan, Dirk J. A. van Zyl

11.1 INTRODUCTION This chapter outlines some of the selection and design considerations for leach pads and liners. Leach pads and liners are generally chosen to provide the required or desired levels of low permeability and foundation conditions at minimum cost. The selection and design of a particular liner depends upon its anticipated use and performance, and what materials may be available. A leach pad is the firm base for a heap. When geomembrane liners are used, the pad is the firm, compacted foundation upon which the liner is placed. In the case of a clay liner, the clay liner is usually also the pad. It is important to consider the design of a pad or liner in terms of a system. The "leach pad system" consists of the prepared foundation, bedding layer (if used), liner (s), seepage collection or detection layer (if used), and cover layer. Foundation preparation is necessary to ensure a stable base for the rest of the leach pad system. A bedding layer is used to protect a liner from being punctured by large angular fragments in the foundation material. A seepage collection or detection layer, consisting of well-drained material and (sometimes) pipes draining to a collection sump, is included when a double liner is used. A cover layer on top of the liner can serve the following purposes (van Zyl and Strachan, 1986): • Preventing of ultraviolet light exposure to sensitive geomembranes; • Limiting evaporation from compacted clay liners and thereby eliminating cracking of such liners; • More efficient collecting of leachate; and • Protecting the liner from damage during heap construction. Economic evaluations of alternative liners for a project must include the overall system. For example, a geomembrane liner may require different foundation preparation and cover material selection and placement than a clay liner. Liners can be made of compacted clay onsite, amended soil, or geomembranes. Geomembrane is a generic term that has been proposed to replace many terms, including synthetic membranes, polymeric membranes, plastic

Jan 1, 1988

By Robert S. Lehto

Zinc concentrates received in La Oroya zinc refinery are marmatitic in nature, contain about 11% iron and traces of other metal values, Figure 1 shows the zinc circuit. The calcine from the roasted concentrates is leached in spent zinc electrolyte. Major part of the impurities is iron which has been oxidized to its trivalent form, This is the origin of the zinc leach residue for which the ZILERET process was developed and so named. The impure liquor from the leach is sent for purification and thence to electrolysis- zinc deposits on aluminum cathodes from which: it is stripped, melted and cast into slabs Typical assays of zinc calcine and leach residue are given in Table 1. Metal values contained in the leach residue, without counting any value of iron, amount to roughly $130 per short ton.

Jan 1, 1969

By Mark E. Gershon

A mixed-integer formulation of the mine scheduling problem is discussed and applied for the purpose of optimizing both the mine production sequencing and the mill blending and processing problems simultaneously. Previous attempts at solving these problems separately, although successful, fail to take into account the interrelationships between these problems. Project structure serves as the outline of this paper, which is directed towards a mining engineering audience. Generalized in its organization, this concept is useful for long, intermediate and short range scheduling. Actual applications are mentioned which show that the concept is also applicable to mining a variety of ores.

Jan 1, 1982

By Emily Wortman-Wunder

While the mood at the 2013 annual joint meeting between the Pittsburgh Coal Mining Institute of America (127th Annual Meeting) and SME Pittsburgh Section (68th Annual Off-the-Record Meeting) in Canonsburg, PA was subdued following a rocky year in the coal industry, attendance was down only slightly, to 300, and overall, the meeting?s focus was optimistic about the future of coal. The conference began by addressing one of the central challenges of coal mining head-on with a keynote address on the status of safety in the mining industry. Noting that two more U.S. miners had died in 2013 than by the same date in 2012, the National Mining Association?s (NMA) Senior Vice President of Regulatory Affairs Bruce Watzman made a plea for a new approach to safety. He described the NMA CORESafety initiative, a program that promotes proactive safety measures versus a compliance-driven model. CORESafety, described in more detail on pp. 29 of this issue, focuses on developing successful ways to change company cultures of safety and behavior. Other industries that have adopted this approach have seen dramatic drops in fatalities, including the Australian mining industry, which has seen its annual fatality rate drop to nearly zero even while the number of people employed in the industry has soared. The rest of the morning?s sessions explored what is arguably the industry?s biggest challenge right now ? maintaining the social license to operate.

Jan 1, 2014

By V. M. Torres

Arapiraca ore deposit has a mixed chalcopyritelbornite mineralogy, with a copper head grade of 0.7%. The reserve size does no allow profitable exploration by grinding/flotation. The technical feasibility of exploring the reserve by heap leaching was studied. Preliminary agitation tests indicated 85% copper recovery. To simulate heap leaching, column tests were performed. The tests included different ore types and acid addition levels. Operating at pH range 1.6-1.8, 67% copper extraction was achieved. Also, it was found an empirical correlation between the operation pH range, copper extraction and acid consumption.

Jan 1, 1996

By Bruce C. Schepens

The Balsam Meadow Hydroelectric Project is currently under construction in central California. TMCI Construction, Inc. was subcontracted to perform the shaft enlargement and lining required for the elevator, surge and power shafts. Involved in the initial work was slashing the elevator and surge shaft into a previously excavated borehole. The elevator shaft then required a reinforced concrete lining and structural steel installation. Throughout the course of construction, numerous design changes occurred, necessitating a lining in both the power and surge shafts. These changes caused TMCI to design two underground hoisting systems to install these additional linings. An analysis of the construction methods used is now given. Introduction The Balsam Meadow Project consists of an underground hydroelectric powerhouse designed to provide additional capacity and energy to the Southern California Edison system during critical peak demand periods, and has the capability for pumped storage operation. The project is located in the Sierra Nevada Mountains about 55 miles northeast of Fresno. The project will divert water presently flowing from Huntington Lake to Shaver Lake to power a single 200 megawatt turbine generator. The approach used to the shaft slashing was governed partially by the strict CAL-OSHA requirements, which became more stringent after the recent Helms' Creek accident. A scaled down sinking plant was used to minimize economic risk and to simplify the excavation and lining scheme.

Jan 1, 1987

By H. Ankara

Determining the identicalness levels of the same model trucks working in open pit mine transportation system by means of statistical analysis methods is very significant in terms of availability analysis. In this study, the identicalness levels of two trucks picked randomly from the 170-short-tonne truck fleet working in open pit coal mine over one-year period were examined through a non-parametric test, Mann-Whitney U test for two samples. Time to failures (TTFs) and Time to Repairs (TTRs) of the trucks were analyzed with this test technique and then whether they were identical or not was determined. In order to determine whether the trucks identified to be identical at the end of this test displayed the same mining performances within the same open pit transportation system, the availability analysis of the identical trucks was carried out. As a result of the availability analysis, it was observed that the trucks had availability values that were very close to each other. It was also determined that Mann-Whitney U test could be employed together with availability analysis. Finally, it was observed that Mann-Whitney U test for two samples could yield rapid results in the performance analysis of complex systems like open pit mines.

Jan 1, 2010

By Richard E. Lounsbury

Coal mine refuse handling traditionally has been the redheaded stepchild of the industry - a problem to be ignored as much as possible. During the past few years, however, mining companies have become more aware of the potential water pollution problem associated with refuse handling and storage. Planning for refuse disposal increasingly emphasizes protection of the environment as well as economics of refuse handling. Coal companies are responding to the environmental control needs by devising new systems and adapting well-known techniques to refuse handling systems. Monterey Coal Company has operated a non-polluting refuse disposal system at its No. 1 Mine for over two years. The purpose of this paper is to describe the design considerations given to the planning of that system and the operational experience gained during its construction

Jan 1, 1973

By D. R. Babich, E. R. Bauer

Noise induced hearing loss (NIHL) continues to be a problem in the mining industry. New noise standards (Part 62) promulgated by the Mine Safety and Health Administration (MSHA) are aimed at reducing NIHL in the mining industry. The National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of noise sources and worker noise exposures to address NIHL in mining. Noise surveys, including full-shift worker noise exposure and equipment noise profiling, have been completed in several surface coal mines, with an emphasis on draglines. The results of these studies are reported, their implications concerning worker NIHL are addressed, and their application to administrative and engineering controls is discussed.

Jan 1, 2003

By D. L. Boreck

With increasing land development, the potential of fatalities from abandoned mine shafts increases. To minimize potential liability, shaft closure should be a critical part of mined land reclamation. The Bureau of Mines is conducting research into using lightweight foam concrete in sealing abandoned coal mine shafts. A demonstration seal consisted of a 3m thick foam concrete plug to provide lateral stability inside the shaft. A high density concrete cap provided load-bearing capacity for a 100-year service life. The USBM has also completed research into changes in foam concrete when it is pumped or dropped from different heights. It is concluded from the research that foam concrete can undergo significant air loss with pumping or dropping. This foretells significant changes in the characteristics of the concrete as well as an increase in the weight and cost of the in-place concrete seal. When using foam concrete to seal abandoned mine shafts, care must be taken to minimize air loss during placement.

Jan 1, 1994

By W. Ripmeester

Canada is committed to the development of indicators to measure the contribution of its minerals and metals sector to sustainable development. The Minerals and Metals Indicators (MMI) Initiative is described, including drivers for the development of indicators, the MMI theoretical framework, the multi-stakeholder consultation process utilized in the development of indicators, and possible policy and business implications of MMI.

Jan 1, 2003

By Jan W. Oberholzer, Jan J. L. Du Plessis, Gerard Appelman, Andrzej M. Wala

The use of on-board scrubbers on continuous miners is an important aspect in efforts to reduce the amount of dust that heading workers are exposed to. As part of the CSIR:Mining Technology's research programme to combat dust, a collaborative project with the University of Pretoria was conducted to evaluate scrubbers. Based on fundamental parameters that were identified to play a role in determining the efficiency of scrubbers, a protocol for testing scrubbers in the laboratory environment, as well as the working section, was established. Tests on various prototype scrubbers were conducted in the laboratory environment. These tests proved some of the fundamental premises according to which scrubbers were designed. By testing some of the newer scrubber types underground, insight into the effect of alternative design aspects on scrubber efficiencies was obtained. The importance of the factors which play a role in reducing the amount of dust in the air is illustrated, as well as the role which other non-design factors play in the reduction of dust levels.

Jan 1, 1995

By Joseph J. Wojcik

INTRODUCTION A great deal more is involved in a sampling effort directed at a placer deposit than physically capturing a quantity of representative material and extracting the desired component. The distribution and dimensions of the sample sites must be chosen after consideration has been given to the type of deposit and the concentrating mechanism. Interpretation of the sampling results is likewise an extremely important part of the sampling program. SAMPLE SPACING The interpretation begins with the selection and design of the sampling program. A decision regarding genesis of the deposits and their geometry must be made in order to select a suitable technique and sampling pattern. Deposits differing genetically will have differing distributions and degrees of concentration.

Jan 1, 1992

By L. F. Ruppert, R. C. Milici

Coalbed methane (CBM) is currently being produced from a relatively small area in the Dunkard and Pocahontas basins, in the northern and central parts of the Appalachian Basin, respectively. In general, much of the production occurs where the coal beds are beneath 500 feet or more of overburden, where the rank of the coal is high-volatile B or greater (%Ro >0.8), and where the natural fracture system is enhanced by structural deformation. It is anticipated that near-term CBM development will continue within these areas and will expand in the Appalachian basin as technology improves and as the price of gas rises.

Jan 1, 2003

By W. D. Elston, A. E. McLaughlin, G. B. Hampton, W. L. Barham, J. F. Murphy, W. H. Cundiff, J. W. Mulloy, R. G. Breuer, J. W. Shaffer

Introduction Alumina (aluminum oxide) is the material from which all the world's aluminum is produced. In the Western World, all the alumina is made from bauxite by the Bayer process. In the nearly 150 years since aluminum was first isolated by Oersted, the metal has grown from a laboratory curiosity to a position of major importance in the world's commerce. In terms of annual production rates aluminum is first among nonferrous metals. Oersted's discovery-reduction of aluminum chloride with potas¬sium amalgam-was improved on by Ste. Claire Deville, whose so¬dium amalgam reduction of aluminum chloride led to the commercial production of aluminum in France in 1855. Ste. Claire Deville's method prevailed until 1886 when Charles Martin Hall and Paul T. Heroult each invented a process for the production of aluminum by the electrolysis of alumina dissolved in molten cryolite. The inven¬tion by Karl Josef Bayer in 1888 of an economical process for making very pure aluminum oxide (alumina) from bauxite established the necessary link between known ores and the Hall-Heroult reduction process. Bayer's work completed the scientific base-the ore bauxite refined to alumina by the Bayer process (U.S. Patent No. 515,895), the alumina reduced to aluminum in the Hall-Heroult cell (U.S. Patent No. 400,766--upon which today's aluminum industry is founded. Small-scale production of aluminum in the U.S. began in 1888 utilizing the Hall cell. By 1903, bauxite properties and a Bayer process refining step had been incorporated into the production activities. On this base the aluminum industry in the U.S. has grown at an annual compounded rate of 15%. Since 1946 the annual growth rate has been 10%.1 The rapid growth of the industry is the result of many factors among which are the existence of widespread bauxite ore deposits; a sound and economic production technology; and the properties of the metal-lightness, strength, ductility, good electrical and heat con¬ductivity, and pleasing appearance, which lead to ever greater de¬mands for aluminum in an industrializing society. At the inception of the industry, the only market that could be found for aluminum was in the production of cooking utensils. How¬ ever, the rapidly accelerating industrial and technological development of the Western World soon created new needs for aluminum, and today aluminum is marketed in a broad range of industrial, commer¬cial, and consumer applications. The principal uses for aluminum are:' building and construction, 22%; transportation, 18%; electrical, 13%; packaging, 11%; consumer durables, 10%; machinery and equipment, 7%; other, 19%. The 1974 production of primary alumi¬num in the world was 14.5 million short tons, which at an approximate ingot price of 40¢ per lb puts a value of $11.6 billion on the industry product prior to fabrication. While aluminum is widely distributed in the earth's crust and is a major constituent of many rocks and soils, to date no method of extraction of aluminum from such nonbauxite material has been brought to commercial practice in the Western World. In the USSR alumina is produced by the complex processing of nepheline syenite, but elsewhere all commercial production of alumina is from bauxite. A brief discussion of recent developments and other processes for alumina is included in the subsection "Other Processes for Alumina," page 19-15. In early 1973, a major U.S. aluminum producer announced the successful development of processes for the production of aluminum from aluminum chloride. This achievement promises to exert a major influence on the future of the aluminum industry. In the initial com¬mercial application of this new technology, Bayer alumina will be chlorinated, and the aluminum chloride then reduced by electrolysis. Important claims for the new processes are lower energy requirements (one-third less than obtainable in Hall cells) and reduced labor costs. Capital costs are said to be no greater than for conventional plants. While the announced intention is to produce the aluminum chlo¬ride from Bayer process alumina, the new chloride reduction process will eliminate the other raw materials, carbon and fluorides, required by the conventional Hall cells. The electrodes in the chloride cell will not be consumed on the reduction process and the electrolyte will have, as the name indicates, a chloride rather than a fluoride base. 2. Bauxite Definition and Origin. Bauxite is a naturally occurring raw material composed principally of a mixture of one or more of the hy¬drated aluminum oxide minerals gibbsite (Al2O2 3H2O), boehmite (Al2O3 H2O), and diaspore (Al2O, - H2O), and impurities of silica, iron oxide, titania, and other various elements in trace amounts. It is an end or near-end product of chemical weathering. Depending on the amount of iron impurities, the color of bauxite varies from dark red and brown to pink to white. Some bauxite is finely divided, free digging earthy material, while other forms are dense and rocky, requiring explosives in mining. Many gradational forms exist. It is one of the most variable of mineral raw materials in chemical composition and physical appearance. It is generally believed that bauxite deposits resulted from intense chemical weathering of aluminum-bearing rocks or formations under tropical or subtropical conditions with alternating wet and dry sea¬sons. Topographic conditions were favorable for drainage and the in-situ accumulation of aluminum, iron, and titanium oxides. There was low to moderate topographic relief with a minimum of erosion during long quiet periods in earth history.2 The occurrence of bauxite is widespread and it has been found on all continents except Antarctica. Production was reported from 27 countries in 1974, at which time total world production was over 79 million metric tons. Of this production 76% was from seven coun¬tries-Australia, Jamaica, Surinam, Guinea, USSR, Guyana, and Greece-which ranked in that order of production. In Table 1 are shown typical compositions of bauxite from some

Jan 1, 1985

By W. Collingwood

As open pit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in open pit mines is often recirculatory. This recirculation traps dust and gases in deep open pit mines. This problem is particularly acute in high latitude open pit mines due to a phenomenon known as an atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In open pit mines, this can result in unhealthy accumulations of gases and other contaminants in the open pit mines. In this study, the natural wind flow patterns in and around open pit mines were investigated using a computational fluid dynamics (CFD) program. Two dimensional models were created for a variety of pit geometries. The effect of depth, slope angle, and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2011

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector, which has an important place in terms of raw material and energy supply, is referred as a sector with one of the highest fatal accidents in comparison with other sectors. In this century, where occupational health and safety awareness has increased, it is important to review the past accident statistics and to determine the current deficiencies by using the information in the inventory. In this study, the Malmquist total factor productivity index (MPI) has been utilized to investigate the changes in the work accidents occurring in the Western Lignite Corporation (Turkey), where underground and surface production methods are applied, and to determine the measures to be taken. According to the results obtained, both the decrease in production amount and the increase in the number of accidents caused inefficiencies during the period in concern due to the expected 10-year economic life of the mechanized system operating in the underground production panel that came to an end in 2007 and the flooding took place in early 2017. Compared with the underground operations, it has been determined that production can be carried out at the appropriate scale despite the heavy working conditions encountered due to the changing climatic conditions and the progress of production in the surface operations.

By Charles S. Robinson

INTRODUCTION Geology, the science of the earth, is the fundamental science in the construction of a tunnel. The approximate site of a tunnel is determined by its purpose. The geology of the tunnel site will determine the cost--or feasibility of a tunnel--the specific alignment to accomplish the purpose of the tunnel, the design of the tunnel (within the limits of the purpose of the tunnel), and the methods of construction. The more accurately the geology of a proposed tunnel can be depicted, the more accurately can the cost of a tunnel be estimated. The factors that should be defined for tunnel design and construction are the physical characteristics of the material in which the tunnel is to be constructed. The physical characteristics of the material are determined by the genesis of the material, and subsequent geologic processes that have affected the material. The geologic materials in which tunnels are constructed can be broadly classified as unconsolidated and consolidated. The unconsolidated materials include chiefly deposits of recent geologic time that occur near the surface. Because these deposits occur near the surface, and tunnels constructed in them will be at shallow depth, methods of physical exploration such as geophysical methods, trenching, and drilling will give more data at relatively low cost--therefore the physical exploration is generally, or should be, quite extensive--and the

Jan 1, 1997