Search Documents

By S. K. Kawatra, H. J. Haselhuhn

"Fine-grained hematite ore can be concentrated by the process of selective flocculation and dispersion, which relies on proper reagent selection and control of water chemistry. While many previous studies have been performed analyzing the effects of different reagents on this process in a laboratory environment, this paper focuses on investigating the water chemistry within the process in a pilot-scale continuous deslime thickener.The pH, sodium concentration, calcium concentration and magnesium concentration were varied to determine their effects on the iron concentrate grade and recovery, and the phosphorus concentrate grade and rejection in the pilotscale selective deslime thickener. The ideal pH for the iron grade and recovery of the process using a starch selective flocculant was found to be 10.5. Phosphorus rejection, however, was increased at lower pH values. Minimization of sodium concentration was shown to improve iron grade, iron recovery and phosphorus rejection. Calcium acted as a nonselective flocculant showing higher iron recovery, lower iron grade and lower phosphorus rejection with increasing concentration. Conclusions could not be drawn from the experiments that varied magnesium concentration.The zeta potential of the solid-liquid interface of particles in each sample taken was also analyzed to show relationships between zeta potential and process performance. In all cases, a maximization of the magnitude of zeta potential correlated with increased iron grade and recovery. This supports the hypothesis that a higher level of dispersion enhances the selective flocculation and separation process.IntroductionThe United States produced 53.2 million metric tons out of the 3,000 million metric tons of concentrated iron ore produced worldwide in 2012 (Tuck, 2013). With this in mind, there has been a large increase in iron ore processing research (Bolen, 2014; Carlson and Kawatra, 2008, 2013; Halt and Kawatra, 2014; Halt et al., 2014; Haselhuhn et al., 2012a,b, 2013a,b; Liu et al., 2014; Manouchehri, 2014; Sandvik and Larsen, 2014; Semberg et al., 2014). Of the 53.2 million metric tons produced, roughly 8 million metric tons of hematite (Fe2O3) concentrate were produced using a process known as selective flocculation and dispersion (Cliffs Natural Resources, 2011). This process is the only economically viable method for concentrating low grade (< 40% Fe) fine grain (< 25µm liberation size) hematite ores. It is scarcely used due to difficulty in controlling the surface chemistry of the ore and high reagent costs (Department of Energy, 2001; Haselhuhn et al., 2013a). The process is highly dependent upon both reagent selection and precise control of the water chemistry during separation. This study shows the dependence of the process performance of a pilot-scale deslime thickener on the water chemistry in the feed slurry."

Jan 1, 2015

By S. L. Bessinger

Introduction In the design and specification of a ventilation system for an underground mine, it is necessary to make reasonably accurate estimates of the pressure losses in the various airways of the mine. These estimates can be made with little difficulty for open airways with simple geometric cross-sections, such as those cut by continuous miners or tunnel-boring machines. The situation is much different on a longwall face, where the airway&apos;s complex geometric cross section and the presence in the airway of obstructing equipment having a variety of shapes make it difficult, if not impossible, to estimate pressure loss using traditional methods of calculation. Head losses in mine entries are calculated using Atkinson&apos;s Equation. [22H= KPLQ (English) H= KP 3Q (SO (1) 5.2AA] where H = pressure loss, in. of H2O (Pa); K = friction factor, lbf•min2/ft4 (kg/m3); P = perimeter, ft (m); L = airway length, ft (m); Q = airflow quantity, ft3/min (m3/sec); and A = flow cross-sectional area, ft2 (m2) In this equation, the friction factor, K, is an empirical constant that describes the aerodynamic roughness of the airway. Typically, the K-factor for a given airway is determined by measuring the factors H, P, L, Q and A in Equation (1) and calculating K. Tables of friction factors calculated in this way are found in textbooks and handbooks that deal with mine ventilation analysis. Unfortunately, very few K-factors have been measured on longwall faces, and the accuracies of those that have been measured are entirely site specific, because of the wide variety of equipment found on longwalls. The development of a technique for prediction without mine-site measurements of the friction factor for any longwall face, regardless of its configuration, will thus be very useful in the design of ventilation systems for mines in which longwall mining is practiced. Calculation of pressure losses using Atkinson&apos;s Equation (1) and empirically determined K-factors provides accurate and useful approximations in cases where the airways have relatively simple cross sections. However, a careful analysis using the principles of fluid mechanics shows that such calculations are based on two assumptions that are not strictly correct when there are obstructions in the airway. The first assumption is that the air velocity distribution in the cross section, particularly around the perimeter, is uniform. This assumption results from the fact that the tabulated K-factor values found in the literature are based on field measurements with uniform conditions. Such uniformity does not exist in longwall airflows. The second common assumption is that the K-factor, and corresponding head loss, is independent of the Reynolds Number (NR) for a given flow. In fact, this assumption is not strictly correct, and is particularly erroneous in the case of irregular protuberances into the airflow, such as those found on a longwall face. The errors arising from the assumptions may be avoided by using K-factors calculated by a newly devised method, described below, which takes into account the fundamental principles of aerodynamic drag analysis. This new technique has two advantages: first, it is flexible enough to model any longwall, regardless of equipment configuration; second, it employs terminology and equations familiar to those who perform mine ventilation analysis, using K-factors, for which ventilation engineers have an intuitive understanding, rather than drag coefficients. To provide guidance for development of a longwall drag model, data were taken on two modern longwalls operating in substantially different conditions. Pressure measurements at Mine B were made with 200-foot (61-m) sections of 1/8-in. (3-mm) diameter plastic tubing, attached to a Dwyer Magnehelic gauge. Pressure drops were measured in 200-foot increments down the face, and summed to give the drop for the entire face length. This technique was found to produce small, repeated errors because of the number of segments required to span the longwall. At Mine A this problem was avoided by using a single, continuous, plastic tube for the entire face length. The psychrometric properties of the air were measured for both Mines A and B. A calibrated, standard vane-anemometer was used to measure the airflow on both faces. Finally, numerous dimensions were measured on both faces, and face profile drawings were obtained to allow detailed evaluation of the face equipment geometry. From this information, accurate evaluations of the average wetted perimeter and average area of the longwall face airways were made. Since the airflow is not confined to inside the powered supports at all points along the face, a quadratically weighted average of the airflows measured at various stations along the face was calculated: [n2Qavg =Qi Ii / It(2)i=1] where [Q, avg = average airflow for analytical purposes, ft3/min (m3/sec); Q= airflow at station i, ft3/min (m3/sec); 1= length of segment represented by Q, ft (m); h= length of longwall face, ft (m): and n= number of quantity measurement stations.] The quadratic weighting scheme was chosen because the

Jan 1, 1992

By R. C. Burtan

Long before the dawn of recorded history, man began to dig into the earth&apos;s crust in a never ending search for useful materials. It has been well established that prehistoric man discovered flint. "The Flintstones" were aptly named. The flintknappers of southern England and Wales still exist today in ever dwindling numbers as they seek out chunks of flint. It is a well known fact that more than half of the earth&apos;s crust is composed of silicon dioxide (SiO2), also known as silica. Silica and silica containing materials have a great many uses in modern society. However, this material is potentially extremely hazardous to our health. Centuries before the Christian Era, Hippocrates wrote of a lung disease common to those who mined in hard rock. It is obvious to us that he was describing silicosis. It is also apparent from ancient writings, that the Egyptians were aware of this malady. Dioscorides also wrote on this subject in the fifth century, B.C. It is undoubtedly the oldest and best studied of the occupational lung diseases. It was certainly described by Agricola in his "De Re Metallica" published in 1556, in which he described lung disease among hard rock miners. This publication, I&apos;m sure, is of special interest and perhaps known to many of you in the mining community. The original document was written in Latin and was translated in 1912 by two gentlemen, Hoover and Hoover. One of these translators was Herbert L. Hoover, a former president of the United States, who made his living before his presidency as a mining engineer.

Jan 1, 1984

By C. L. Peng, F. F. Min, S. X. Song

"Using a parameter representing the degree of hydration of particles in a liquid called hydration index I, which we derived based on Einstein’s viscosity equation, we evaluated the degree of hydration of fine montmorillonite particles in different aqueous solutions by measuring the viscosities of the montmorillonite dispersions and plotting relative viscosity against volume fraction of dry montmorillonite particles in the dispersions. We investigated the effects on the hydration of montmorillonite in aqueous solutions of (1) the type and (2) the concentration of electrolytes in the solutions and (3) pH. For the same concentration of electrolytes, the hydration index I of montmorillonite was found to increase in the order of Na+ > K+ for monovalent cations and Mg2+ > Ca2+ for divalent cations, and to decrease with increasing valence of cations in the order of Na+ > Ca2+ > Al3+. For both Na+ and Ca2+, the hydration index I first increased with increasing concentration of electrolytes and then decreased after a certain concentration. The hydration index I increased with increasing pH. IntroductionClay minerals have the distinctive ability to adsorb water molecules and hydrated cations in aqueous solutions, resulting in hydration on their outer surfaces and in their interlayer spaces. Many investigators (Jurinak, 1963; Anderson and Tice, 1971; Costanzo et al., 1982; Israelachvili, 1992) had found evidence of ice-like structures of water on clay minerals.This phenomenon of hydration plays an important role in the dispersion and sedimentation of clay minerals in aqueous solutions. To understand clay hydration, numerous experimental and simulation studies have been carried out since 1933, including the recent ones of Hawkins and Egelstaff (1980), Skipper et al. (1995), Karaborni et al. (1996), Salles et al. (2013) and Morrow et al. (2013). Among the factors that can influence a clay mineral’s hydration characteristics are chemical composition, type and degree of isomorphous replacement in its structure, and number and nature of associated exchangeable cations."

Jan 1, 2015

By T. Good

Twin roll sizers are neither compactly designed machines nor are they configured to accommodate underground mobility; in fact, twin roll sizers leave room for improvement in many aspects of the design. The DRC1200 capitalizes on the weaknesses of these machines to make a more productive, easily maintained, and compact twin roll sizer than current market offerings. These strides were made through the inception of the Hard Rock Extraction System (HRXS), which requires a mobile sizer as part of the system. After use of a third party sizer on the HRXS, potential improvements were evident. These improvements include improved structural design to reduce overall footprint and an optimized design to reduce operating cost.

Feb 23, 2014

By S. Roy

Soft laminated iron ore (SLO) having a higher hematite content and Martite goethite iron ore (MGO) having a higher goethite content were subjected to detailed characterization and beneficiation. The present research was designed to investigate if these abundant, low-grade ores can be enriched adequately using standard industry techniques. No significant enrichment of the ores using jigging operation on the coarse (-3,200 +595 mm) size fraction could be achieved. Good liberation was only attained in the 150 to 300 mm particle size range in both cases. Desliming enriches the ground ores significantly. The effect of the feed size on the separation efficiencies of the ground ores were studied using flowing-film concentration on a Wilfley table. Better enrichment is obtained in the case of 150-mm sized feed by tabling. The grade of SLO is improved from 56.14% to 66.51% Fe, while the Fe content of MGO is enriched from 55.16% to 65.83%. Substantial rejection of alumina and silica is also achieved. Due to the friable nature of MGO and the higher goethite content in it, the loss of Fe in the form of ultrafines is greater in this case compared to that of SLO.

Jan 1, 2009

By J. J. Gusek, T. C. Richmond, R. W. Reisinger

A high-altitude (9,500-ft [2,900-m]) historic underground copper mine in Wyoming discharges neutral but copper-laden water into a pristine creek. Under a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) deferral agreement, the Wyoming Abandoned Mine Land Program performed site characterization and treatment studies in preparation for reclamation of the site. An integral part of the project included addressing the needs of a variety of interested and affected parties, including property owners, local populations, government agencies, and the media. This paper discusses an overall approach and specific methods employed to enlist public support for the project as well as some of the successes and failures experienced.

Jan 1, 2004

By Joseph F. Shirley

A froth flotation plant to recover by-product molybdenite must be designed specifically for the selected separation process and the type of ore being treated. However, some general rules concerning by-product molybdenite plant design can be suggested that would be valid for most processes. The term by-product molybdenite in this paper is limited to the recovery of molybdenite from copper porphyry ores, which essentially amounts to selectively separating molybdenite from copper and iron sulfide concentrates. In addition, most of the discussions would apply only to the almost universally used approach of floating the molybdenite and depressing the copper and iron sulfide minerals.

Jan 1, 1979

By V. Kecojevic

The objective of this research was to establish the relationship between production, consumption and energy cost in the surface mining of bituminous coal. Specific energy sources such as diesel, gasoline, electricity, explosives and bituminous coal were considered in this study. Gain in net energy, proportion of the cost of energy consumption and total energy cost relative to total revenue of extracted coal were determined, and a new energy efficiency index and a new energy-cost ratio were established. A case study on an operating surface coal mine was carried out to demonstrate the application of the newly developed method. The results of this study can be used by the mine operators in establishing strategies for the optimization of energy production and consumption, and for reducing the cost of bituminous coal extraction.

Jan 1, 2014

By Frank E. McCall, Michael A. Trevits, Fred Garcia

The U.S. Bureau of Mines investigated the influence of atmospheric pressure changes on methane gas migration through mine seals at a mine site located in the Pittsburgh Coalbed. The mine gained access to a coal reserve through part of an abandoned mine and constructed nine seals to isolate the extensive old workings from the active mine area. Underground problems were experienced when atmospheric pressure fell, causing methane gas to migrate around the seals and into the active workings. During mining operations, methane gas levels exceeded legal limits and coal production was halted until the ventilation system could be improved. When mining resumed with increased air flow, methane gas concentrations occasionally exceeded the legal limits and production had to be halted until the methane level fell within the mandated limit. To assist the ventilation system, a pressure relief borehole located in the abandoned workings near the mine seals was proposed. Preliminary estimates by a gob gas simulator (computer model) suggested that a 0.76 m (2.5 ft) diameter pressure relief borehole with an exhaust fan would be necessary to remove enough methane from the abandoned area so that the ventilation system could dilute the gas in the active workings. However, by monitoring methane gas emissions and seal pressure, during periods of low atmospheric pressure, the amount of methane gas that migrated into the active mine workings was calculated. Researchers then determined that a relief borehole, 20.3 cm (8-in) with an exhaust fan could remove at least twice the maximum measured volume of migrating methane gas. Because gas concentrations in the abandoned workings could potentially reach explosive limits, it was proposed that the mine eliminate the exhaust fan. Installation of the recommended borehole and enlarging two other ventilation boreholes located in the abandoned area reduced methane gas leakage through the seals by at least 63%.

Jan 1, 1995

Geostatistical literature has been dealing with recoverable reserve estimation techniques for the last 30 years. There have been well established support correction techniques (Le. affine correction, indirect log-normal correction, etc.) to deal with volume -variance relationship globally in determining what will be the reserves above a cutoff grade during mining. Kriging has become the accepted technique in the mining industry for ore reserve estimation. Many large companies are using this method for gold and copper deposit modeling. In general, the estimates coming from kriging are smooth. The variances of the block grades estimated by kriging are often lower than the material that will be mined selectively. As a result, kriging tends to under estimate reserves at high cutoff grades and overestimates them in low cutoff grades. It is necessary to perform additional steps after kriging if the goal is to determine recoverable reserves at some cutoff and not the in situ resources. In the mining industry, it is becoming more and more common for the low grade heap leach projects to consider whether the higher grade portion of a deposit may be processed by a mill at higher profits. Similarly, a concentrator -refinery operations are implementing heap leach -SX-EW option for the lower grade portion of their deposit. These options are making it very critical to estimate the low and high end of the grade distributions more accurately. Ore reserve estimation is normally done by using widely spaced exploration data which has very small size support (Le. core samples). Selective mining is carried out on ore control that is based on closely spaced blasthole data normally averaged into larger polygons based on some cutoff grade. Estimated grades from exploration data need to reflect the variability of the grades of the selectively mined units if they are used without further adjustments to predict recoverable reserves.

Jan 1, 1997

By Bart Hogeweg

The development of deep sea mineral deposits creates a new horizon for the mining industry. In a field where mining technology meets deep-water offshore engineering, new challenges are faced to come to the successful exploitation of these deposits. With the absence of proven technology for the mining of these minerals, a ?technological green field? is entered. IHC Merwede (IHC), a global market leader in the dredging and wet mining industry, is on the frontline of these developments. MTI Holland, IHC Merwede?s research and development company, has undertaken a number research efforts focused on the successful development of technology for the mining of deep sea minerals. This paper highlights a number of these efforts and illustrates IHC?s continued dedication for the research and development of technology to enable the commercial mining of deep sea minerals.

Jan 1, 2008

By George E. Aikens

Prolonged subzero climatic conditions impose some unique engineering problems for the developer and operator of open-pit mines in the Far North. The remoteness of the job site and the extremely cold, long, dark winters severely tax both man and machine in the quest for the Arctic&apos;s rich mineral wealth. Undoubtedly the singular most troublesome problem for the engineer is Permafrost which underlies about 201o of the land area of the world and about 85% of the state of Alaska. Permafrost has its impact on building construction and mine excavation, while posing a more pervasive threat to the-delicate ecologic balance within the Arctic wilderness. Yet the difficulties associated with mining up North may not be as overwhelming as has been previously supposed. For example, the lowest temperature recorded at Point Barrow is -560F, whereas Montana has recorded -69.7° F.. There are no specially designed machines for mining and construction in the Arctic, and efficient equipment utilization is maintained through proper operation and servicing techniques. However, neither equipment or people can be assumed to function normally at -40°F. Special techniques in drilling, blasting, and ripping are being used to yield economically competitive ores. Overall, a fundamental understanding of the nature of Permafrost will allow the engineer to deal expeditiously with an Arctic mining venture and at the same time to deal fairly with Arctic environment.

Jan 1, 1972

By Ralph M. Stricklen

The need to move large tonnages of slurry has grown as mines have become larger. As existing tailing depositories are filled up, new mines developed, or environmental requirements dictate, it becomes necessary to transport tailing particularly over longer distances. A typical slurry transport system is shown in Figure 1A. Figures 1B, 1C and 1D show sketches of the system auxilliary components: feed box, receiving sump and drop box, respectively. There are two basic types of slurry transport systems, packed flow and slack flow. Packed flow is typified by a pipe running full; slack flow by a launder or pipe running less than full. Slack flow in launders or channels is also referred to as open channel flow. Generally slack flow slurry transportation involves a flow with less than 65 per cent solids, and there is an upper limit on particle size, depending on the slope of the system.

Jan 1, 1984

By W. R. Junge

The investigation, selection, and implementation of remedial activities for large, complex mining and milling sites is dependent on the cost-effective management of tailing and waste materials. Site investigations evaluate the contaminant source areas, assess the potential release rate of contaminants, and determine the acceptable contaminant release rate for the site. Selection of appropriate remedial activities is based on evaluation of constructability, reliability, performance, effectiveness, permanence and cost. Remedial technologies available for tailing and waste material include removal, consolidation, capping and drainage control. Proper implementation and documentation of the selected remedial activities are critical to the overall success or failure of the remedial program. A step-by-step process, established at the initiation of a project, should accurately document all construction activities, monitor environmental conditions at the site, assess the performance of the remedial activities, and, ultimately certify that the remedial activities have met relevant and appropriate standards. Case histories are presented for a uranium mill at Uravan, Colorado and a lead, zinc mine at Gilman, Colorado. These case histories provide examples as to the combination of remedial technologies that have been applied at these specific sites.

Jan 1, 1989

By G. Chi, M. C. Fuerstenau, R. C. Bradt

Reduction of the total energy expenditure in mining and ore preparation processes was achieved by redistribution of the energy from the crushing and grinding steps to the blasting operation. Reducing the burden/spacing distance by 25% or increasing the charge length by 25% during blasting results in significant energy savings in subsequent comminution processes. The energy cost of mining and comminution is reduced by up to 10%.

Jan 1, 1995

By C. G. Anderson

The treatment of materials for the recovery of the precious metals imposes many processing and environmental challenges. Sunshine Mining and Refining Company has developed hydrometallurgical technology for recovery of values from refractory precious metal materials. At Sunshine, the industrial focus of these processes has been for the direct recovery of silver without cyanidation. However, recent work has indicated that these technologies can provide a means for treating complex, refractory gold concentrates. This will be the focus of this paper. The practice of pretreating ores and concentrates to make them more amenable to cyanidation is becoming more common. Several pretreatment options for sulfide concentrates containing gold include roasting, bio-leaching, direct pressure oxidation and nitrogen species catalyzed pressure oxidation. The industrial use of nitrogen species catalyzed pressure oxidation has been limited to the Sunshine refinery where its focus has been for the treatment of silver concentrates. Much of the reluctance, outside of Sunshine, to use this type of technology may be based on the perception that high costs are associated with using nitrogen species (e.g. nitric acid, sodium nitrite) to leach. Also, the use of nitrogen species catalyzed pressure oxidation on an industrial scale is unfamiliar to most metallurgical professionals. A summary of pressure leaching processes which utilize nitrogen species as a catalyst is presented in Tables 1 and 2.

Jan 1, 1996

By A. D. Davis, C. J. Webb

Brohm Mining Co.&apos;s Gilt Edge Mine in the northern Black Hills was a surface heap-leach operation that was active from the 1980s until 1999. Financing problems and acid drainage concerns at the mine were reported in the late 1990s. In February 1999 the Governor of South Dakota announced plans to request the US Environmental Protection Agency to help clean up acidic water at the mine and reclaim the site. In July 1999 the parent company of Brohm, Dakota Mining, filed for bankruptcy in Canada. Because of the bankruptcy and environmental problems, the State of South Dakota intervened and began water treatment. The mine was declared a Superfund site in 2000. Hydrologic issues include the potential for acidic drainage from the site. The mine is at the headwaters of Strawberry Creek, which drains into Bear Butte Creek. About four miles downstream, Bear Butte Creek loses its discharge to swallow holes in the karstic Madison Limestone aquifer, a regionally extensive and valuable groundwater reservoir. Other concerns at the site include treatment of acidic water in mine pits and a waste rock dump.

Jan 1, 2003

By D. Leppert

Mr. Garrett brings up several interesting points with respect to the proposed API specification for "nontreated bentonite." However, although not explicitly stated, these specifications are being written based strictly on bentonites from the Wyoming/South Dakota area. Other sodium bentonites may be suitable for use as drill mud but will be unacceptable since the specifications are designed for Wyoming bentonites. Regardless of the API&apos;s intent that its specifications are intended only as guidelines, they are generally adhered to on an international basis and, for practical purposes, might as well be chiseled in stone. Estes (1986) notes that the quality of bentonite available from Wyoming producers has steadily declined since the early 1960&apos;s. The plastic viscosity: yield point (PV:YP) ratio was included in the current API 13A specification primarily to prevent excessive polymer treatment of lower quality bentonites to make drill mud. However, with development of polymers designed to control YP, this specification cannot ensure that only high-quality bentonites are used for drill mud. Nor will the new specifications for untreated bentonites. Other sodium bentonites are available. Bentonite produced in southeast Oregon demonstrates superior performance characteristics without addition of polymer or other chemicals. However, the exceptionally high purity of these deposits leads to a relatively high YP:PV ratio since the naturally high YP probably results from the higher purity and smaller particle size of this bentonite (Rath, 1986 and personal communication). These bentonites typically have a smectite component exceeding 90% (Rath, 1985), compared with 70% to 75% smectite for typical Wyoming bentonites, as determined by X¬ray diffraction and tests for colloid content. As evident from the accompanying table, the untreated Oregon bentonite has excellent rheological properties, though different from Wyoming bentonites due to the high purity. Additionally, this bentonite reacts well with polymers typically used in the oil industry, making it eminently suitable for use in a low-solids mud system. The extremely low grit content, less that 0.5% on a 75 mm (200-mesh) wet sieve, greatly exceeds the standards set for Wyoming bentonite. Optimum rheological properties are obtained at a higher moisture content than Wyoming bentonites. At 10% moisture, API 13A maximum, the clay is overdried, again reflecting the high smectite content. In summary, the specifications proposed by the API Task Group will ensure that only Wyoming producers can supply "nontreated" bentonite to the oilfield since specifications are

Jan 1, 1989

By D. Kwietnewski

The 4th bore of the Caldecott Tunnel is a 50-ft horseshoe shaped highway tunnel located in the hills east of Oakland, California. Tunnel excavation was mostly completed using one of the world?s largest commercially available roadheaders, a Wirth T3.20. The geologic profile included seven different geologic units, which displayed a range of different behavior with regard to excavation and initial support. Following a brief introduction to the excavation and support methods, this paper will discuss roadheader performance in the various geologic units encountered during excavation. Comments will also be made concerning the relationship between the roadheader method of excavation and observed ground convergence during excavation.

Feb 27, 2013