Search Documents

By D. S. Choi

This paper presents the results of geomechanics work applied to the longwall operation. The mining method was successfully adapted to US mining conditions resulting in an improvement in safety and productivity. The paper deals with various geomechanics problems associated with geologic and mining conditions.

Jan 1, 1987

By Michael E. Kelahan, Glenn A. Gruber

A review of recent phosphate beneficiation developments shows that Flotaire cells, ranging from 0.20 m to 2.44 m in diameter, have been examined in pilot scale and commercial plants. Applications of the column cells have included sized feed fractions using anionic and cationic reagent systems. In plants where the Flotaire was installed as a test unit or as an optional circuit, its use has been largely discontinued. On the other hand, when management committed to installing the Flotaire as an integral part of the flowsheet, the performance expectations were met or exceeded.

Jan 1, 1988

By M. E. Gershon

Extensive efforts are under way toward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics, and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1987

By Y. M. Jiang

Longwall faces can move at high advancing rates, but many geological variations can cause unexpected instabilities and production losses. The rapid movement makes it necessary to evaluate different geologic conditions in the rock mass as fast as possible to assess their effects on the longwall face and shields. It is believed that prompt awareness of geologic conditions is the key to preventing instability at a longwall face. This paper introduces the application of fuzzy set theory for characterizing and evaluating roof conditions. Real-time monitored data coupled with fuzzy set analysis provides valuable information, such as shield leg pressure, developing load on shields, intervals of periodic weighting and the ratio of developing loads during periodic to normal times.

Jan 1, 1997

By J. F. Whelan, B. D. Marshall, Z. E. Peterman, J. B. Paces, L. A. Neymark

Observations of calcite and opal in cavities in the unsaturated zone at Yucca Mountain indicate that: 1) seeps are not regularly spaced in underground workings and not all fractures sustain flow, 2) many cavities represent sites of seepage that have remained stable for millions of years, 3) typically there is no evidence (such as dripstone) for seepage dripping into cavities from their ceilings, and 4) seepage is not likely to be greater than about 1 liter of water per year (per 5-m-long drift) based on calcite abundances observed in the ESF. This estimate of seepage is significantly lower than that used for performance assessment.

Jan 1, 2000

By Barnaby J. Watten, Sibrell. Philip L., Brian J. Vinci, Andrew E. Friedrich

We evaluated a new process for remediation of acid rock drainage (ARD). The process treats ARD with intermittently fluidized beds of granular limestone maintained within a continuous flow reactor pressurized with CO2. Tests were performed over a thirty day period at the Toby Creek mine drainage treatment plant, Elk County, Pennsylvania in cooperation with the Pennsylvania Department of Environmental Protection. Equipment performance was established at operating pressures of 0,34,82, and 117 kPa using an ARD flow of 227 L/min. The ARD had the following characteristics: pH, 3.1; temperature, 10 OC; dissolved oxygen, 6.4 mg/L; acidity, 260 mg/5; total iron, 21 mg/L; aluminum, 22 mg/L; manganese, 7.5 mg/L; and conductivity, 1400 uS/cm. In all cases tested, processed ARD was net alkaline with mean pH and alkalinities of 6.7 and 59 mg/L at a CO2 pressure of 0 kPa, 6.6 and 158 mg/L at 34 kPa, 7.4 and 240 mg/L at 82 kPa, and 7.4 and 290 mg/L at 117 kPa Processed ARD alkalinities were correlated to the settled bed depth (p<0.001) and CO2 pressure (p<0.001). Iron, aluminum, and manganese removal efficiencies of 96%, 99%, and 5%, respectively, were achieved with filtration following treatment. No indications of metal hydroxide precipitation or armoring of the limestone were observed. The surplus alkalinity established at 82 kPa was successful in treating an equivalent of 1136 L/min (fivefold dilution) of the combined three ARD streams entering the Toby Creek Plant. This side-stream capability provides savings in treatment unit scale as well as flexibility in treatment effect. The capability of the system to handle higher influent acidity was tested by elevating the acidity to 5000 mg/L with sulfuric acid. Net alkaline effluent was produced, indicating applicability of the process to highly acidic ARD.

Jan 1, 2000

By Lynn B. Hales, Randy A. Ynchausti

Expert supervisory control strategies have been used for many years to improve operating revenues in comminution circuits. Typical improvements in capacity range from four to eight percent. Several case studies of results will be presented as well as a general discussion of the technologies used to achieve the improvements. Crushing. SAG milling and ball milling circuits will be discussed.

Jan 1, 1997

By L. Mao, R. Yoon

The thin film balance (TFB) technique was used to measure the equilibrium thicknesses of the water films formed between two oil phases. The measurements were conducted with dodecane at varying concentrations of dodecylammonium chloride, pH, and electrolyte concentration. The data obtained in the present work were used to calculate the surface forces acting between the two oil phases. The calculation was carried using the Extended-DLVO theory with the surface potentials calculated from the Gibbs adsorption isotherm. The results show that oil droplets suspended in water are hydrophobic and the hydrophobicity changes with surfactant and electrolyte concentrations.

Jan 1, 2004

By Des B. Bolton, Neil P. Boland

Typically, environmental work on mine sites in Northern Australia involves addressing an individual problem as it arises. However, individual mining companies are moving toward a more holistic approach to managing the interactions between the environment and the mining process and are thus pre-empting environmental problems. This paper presents a broad overview of this holistic approach and provides a few examples, drawn from our own experience, which illustrate some of the tangible benefits to be gained from Environmental Planning.

Jan 1, 1991

By Chuck Hornaday, Brad Miller

Geosynthetic clay liners (GCLs) are manufactured barrier layers containing a high-quality sodium bentonite clay attached or adhered to geotextiles or a geomembrane. The GCL's low permeability and high strength make it an ideal replacement for low permeability soil or clay liners for mineral extraction and processing containment applications. This paper will discuss the advantages of utilizing a GCL versus compacted clay in containment applications. Some of the advantages include: the GCL's lower permeability (5 x 10-9 centimeters per second (cm/sec)) and corresponding better composite liner leakage protection, the GCL' s greater resistance to desiccation, differential subsidence and freeze­thaw, and lastly, the ease and speed of installing the GCL. This paper will also detail a number of important case studies related to the mineral extraction and processing industry. These case studies include using GCL in two large reclamation capping projects, as a secondary liner in two gold heap leach pads, as a composite liner in a dam for stormwater runoff control, and lastly, as a primary liner for a tailings runoff diversion channel.

Jan 1, 1997

By C. A. Rowland

Introduction Ball mills are lined drums, either cylindrical in shape or modified cylinders that have either one or both ends of the shell, consisting of conical sections, that rotate about the horizontal axis. Fig. I I shows a cylindrical mill, Fig. 12 a conical ball mill, and Fig. 13 a Tricone ball mill (Hardinge tradename). Steel or iron grinding media, generally in the shape of spheres, are used to grind the ore to the specified product size. In order to obtain more contact area for grinding and to simulate the shape of worn balls, balls have been made with two concave surfaces diametrically opposite each other. Some concentra¬tors, such as Erie Mining Co., have used slugs cut from worn and broken rods to supplement the balls in ball mills and save money otherwise lost as rod scrap. Cylindrical and conical shapes have been tried instead of balls, but balls remain as the most common shape grinding media used in ball mills. Ball mills were a logical development from the earlier pebble mills that used hard natural pebbles such as flint pebbles or sized ore pebbles (obtained from the ore itself) as grinding media. In the early 1900s36 it was found that when cast iron or cast steel balls were used in place of flint or ore pebbles, the mills drew more power and gave greater production capacity. Advances in technology have resulted in the manufacture of ball mills up to 18 ft diam inside shell, drawing up to 8,000 hp. Ball mills are employed to grind ores, especially the more abrasive ores, to finer sizes than can be produced economically in other size¬reduction machines such as roll crushers, hammer mills, and impactors. Ores can be ground dry-dry grinding-or in a slurry-wet grinding-using ball mills. Dry grinding nominally refers to less than I %v moisture by weight. If the moisture content increases by several percent, dry grinding capacity is significantly reduced as shown in Table 17. The usual range of solids content in wet ball-mill slurries is from 65 to 80% by weight. Wet grinding is used to prepare the feed material for unit opera¬tions such as flotation, magnetic separation, gravity concentration, and leaching that require a slurry of liberated valuable mineral and unwanted gangue particles. Dry grinding" is employed to produce feed for agglomeration, pelletizing, and pyrometallurgy processes that require feed that is dry or nearly so and for finely ground industrial mineral products used in the dry state. Dry grinding is also used when minerals cannot be dewatered economically to the required moisture level or when the ground product reacts unfavorably with liquids. For example, cement clinker must be ground dry. Dry grinding requires about 30% more power than wet grinding for comparable size reduction .28 The total power required in a dry¬grinding ball-mill plant including drying may be double that required for a wet-grinding plant. Grinding-media and liner consumption in dry grinding reported as pounds of metal consumed per kilowatt-hour per ton of ore" is 10-20% of that used in wet grinding. The Wabush pellet plant, Point Noire, Que.3o reported ball consumption dropped from 6.3 lb per ton of ore ground to 2.5 lb per ton of ore ground when they converted from wet to dry grinding, and a 30% increase in power consumption. A number of comparisons made on wet and dry grinding of cement raw materials show metal consumption in dry grinding to be 10% of that in wet grinding. The capital costs for wet grinding are generally lower than for dry grinding. When thickening and filtering of the wet-ground product are required, dry grinding may have a lower capital cost. With open-circuit grinding the ball-mill discharge passes directly to the next processing step without being screened or classified and no fraction is returned to the ball mill (Fig. 14). In closed-circuit grinding the ground material, undersize, in the ball-mill discharge is removed either using a screen or a classifier with the oversize being returned to the mill for additional size reduction (Fig. 15). The over¬size material that is returned to the ball mill is called the circulating load. Open-circuit ball-mill grinding requires more power than closed¬-circuit grinding for products containing similar amounts of top-size material. The less the amount of oversize allowed in the product, the longer the ore must remain in the ball mill when grinding in open circuit. This increases the production of extreme fines and thus the consumption of more power. The power required for open-circuit ball-mill grinding can be estimated using the multipliers listed in Table 18 and knowing the power required for closed-circuit grinding to yield the desired product particle size. For example, assuming the desired grind size is 90% passing some specific top size, open-¬circuit grinding would require 1.40 times the power to achieve similar results as closed-circuit grinding.

Jan 1, 1985

By Petr Salak, Adrian St. John, Angelos Gakis

"INTRODUCTIONCrossrail will provide London and the South East of England with a world class, high-capacity railway to ease congestion on London’s public transport system and enable better access between business, residential and entertainment districts. At the heart of this £14.8bn scheme lies Farringdon Station, which will form a major interchange between Crossrail, Thameslink and London Underground. The £400m Farringdon Crossrail station was awarded to a joint venture of BAM Ferrovial Kier (BFK) in 2011, and comprises two ticket halls, two platform tunnels and a multitude of connecting tunnels all constructed using open face sprayed concrete linings (SCL). BFK appointed Dr. Sauer & Partners (DSP) as their specialist SCL designer. As the main contractor for both C300/C410, the Western Running Tunnels and Station Caverns, and also for C435 Farringdon Station, BFK were in a unique position to develop strategies to reduce cost, time and risk for the Client. One such innovation involved the continuation of the TBM drives for the running tunnels right through the length of the new Farringdon platform caverns. This created large diameter precast concrete pilot tunnels for the subsequent platform enlargement using SCL. The benefits of such an approach are described in detail by St.John et al 2015. BFK also introduced another alternative strategy to reduce cost, time and risk, by proposing to abandon the TBMs in the ground (“Turn & Bury”) permanently rather than recovering them through the ticket hall shafts. This de-risked the programme, enabling critical ticket hall construction to proceed unhindered. However, one consequence of this revised strategy was an area of increased underground congestion, with two SCL tunnels (RTE2 and ES2) and a bored tunnel (complete with abandoned TBM) in close proximity to a ticket hall excavation (see Figure 1) and a sensitive, listed railway structure. Faced with this complex geometry, and combined with challenging geotechnical conditions (Gakis et al 2015), the team chose to install enhanced monitoring to study the behavior of tunnel RTE2 and provide additional assurance that the tunnels were performing as predicted. Applying advanced 3D numerical modelling and taking into account the residual tensile strength of the SCL helped avoid unnecessary reinforcement installation in primary lining and/or early installation of a secondary lining in RTE2 prior to ES2 construction."

Jan 1, 2016

By Jamal Rostami, Ataollah Rahbar, Jürgen Paulzen

"Uma Oya Multipurpose Development Project is located in South West Sri Lanka. This project, among many components, involves a 14 km headrace tunnel in very hard and abrasive igneous rocks. The tunnel is under construction by a 4.4 m diameter double shield TBM. The headrace tunnel has already reached 5km milestone and has passed through some reaches of tunnel in very strong intact rocks with no joints. Low penetration at high thrust load has caused frequent stoppages for cutter change leading to low utilization and advance rates due to low cutter life. The original machine was dressed with 27, each 432 mm (17 inch) diameter, 19 mm (3/4 inch) tipped disc cutters. However, various cutter diameters of 432-457 mm (17-18 inch) and cutter tip widths 13 to 19 mm (0.5-0.75 in), have been tried to see if cutter life and penetration rates could be increased. This paper will review the history of the project, the geology of the site, along with TBM performance and cutter life. It will focus on frequency of different cutter failures encountered in various ground conditions. Also, results of using variation of cutter diameter and tip width to cope with the hard rock conditions and their results in increasing machine productivity will be discussed. This allows for better understanding of parameters controlling disc wear/life and leads to better cutter management for more efficient operation of hard rock TBMs in similar conditions. INTRODUCTION The Uma Oya Multipurpose Development Project (UOMDP) lies in the south-eastern part of the central highland region of Sri Lanka. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya river. The feeder (or power) tunnel Lot consists of a 15554 m long headrace tunnel (HRT), the surge shaft and tank on the upstream of the vertical shaft, a 650 m vertical shaft with steel lining, and an underground powerhouse and a 3650m tailrace tunnel (TRT)."

Jan 1, 2016

By L. Borsch

Geochemical laboratories are commonly criticized by geologists about poor analytical reproducibility and erratic anomaly patterns, especially when gold and trace metals from resistant minerals are reported. Geochemical analysis in mineral exploration is a compromise between high productivity on the one hand, imposed by large numbers of samples, and analytical precision and accuracy on the other. However, the physical properties of resistant minerals, such as cassiterite, gold, beryl, chromite, zircon and others, interfere with both of these requirements. Therefore, the degree of sample homogeneity that can reasonably be achieved in sampling and sample preparation must be considered. Subsequently, the understanding of its effects on analytical data quality and the consequences on data interpretation will provide a basis for understanding the problems common to exploration as an interdisciplinary science. Complaints about poor and inadequate analytical performance are not confined to exploration geochemistry. They are a common feature in mining and metallurgy and wherever sampling and analysis of "grains" are concerned - the "nugget" or "grain size effect." The "grain size" effect Poor analytical reproducibility is normal for gold and a well-defined group of other elements usually found in resistant placer minerals. Those who use and interpret geochemical data must realize and appreciate the chemical, the physicochemical, the physical and the mineralogical properties of the elements and their minerals. Especially for the "placer" minerals and their elements, such comprehensive interpretation is crucial. The most important factor to consider is the behavior of a mineral and its metal component(s) during weathering and their integration into the sampled medium, in exploration mostly sediments and soils. (Data interpretation for samples of water, gas, to a certain extent rock, follows different patterns.) A mineral may be chemically and physically stable or it may easily disintegrate physically or decompose chemically, or any combination of such processes, at varying degrees. The breakdown products, in turn, may or may not, interreact with the environment. If the nature of an element or a mineral predestines it for a heterogenous distribution in the sample medium, then nature, size and number of grains likely to occur should be considered in relation to the sample portion taken for analysis. This allows the estimation of their effect on analytical precision and accuracy. Elaborate and sophisticated statistical calculations exist on this subject. But these approaches do not cope with the complexity of the natural surface environment. The miner alogical, chemical and environmental behavior of elements and minerals can be estimated but not calculated. However, the mineral grain sizes and their influence on analytical precision can be precisely calculated if certain conditions, assumptions and idealizations are made. If the geochemical and mineralogical characteristics of minerals and elements are understood, such calculations demonstrate the grain (or nugget) effects that mineral properties and (geo)chemical behavior of minerals and elements cause on the precision and accuracy of geochemical analysis through their influence on sample homogeneity. Two other factors that influence the sample homogeneity and the nugget effect are the efficiency of sample preparation and the sample portion taken for analysis. In this way, certain element- or mineral-specific parameters can be established as a guide for the sampling program. The information, for example, may assist in determining sampling procedures in the field, especially the sample weight to be taken for "representative samples." Also, it may help assess whether analytical data, as provided by the laboratory, are acceptable. Finally, it may help determine the approach in data interpretation. However, all such simplified calculations are based on idealized, that is, unreal assumptions and conditions. As such, they represent one extreme end on the scale of probabilities. The reality is found somewhere away from this extreme, towards homogeneity. An example from a study of an eluvial gold prospect may be given for illustration: •Original sample weight: 20 kg (44 lbs) of rock gravel, crushed and ground to -0.18 mm (-80 mesh). •Au content: 20 grains of Au, average size of about 0.5 mm3 (0.03 cu in.) each = 7.5 mg each, making a total of about 150 mg Au in the sample = 7.5 ppm Au. Assumptions •Au occurs in the sample as free, discrete grains only. •Not more than one grain, if any, goes into each sample split (analyte) portion (20 grains of 7.5 mg Au each). •Analysis of original rock sample: 100 g sample for analysis, 20 kg/100 g = 200 samples 20 samples with 1 grain each: result, - 75 ppm Au. 180 samples with no grain: result, 0 ppm Au chances 1:9 •10 g sample for analysis:

Jan 1, 1996

By Joseph B. Alberts, David D. DiPonio, Francis B. Manning

From 1996 to 2001, Wayne County and 13 suburban Detroit communities constructed the Downriver Regional Storage and Transport System (DRSTS) to improve area water quality, protect public health and alleviate basement flooding. The project consisted of a 10-mile long storage and transport tunnel, a pump station at the existing wastewater treatment plant, 9 miles of relief sewers (6 in tunnel and 3 in open cut). The work was separated into 10 contracts. Due to hydraulic design requirements and other constraints, the tunnel profile was located generally 65 feet below ground surface within a soft to medium clay strata which skimmed along the top of a very dense glacial till “hardpan” overlaying bedrock. Boulders within the tunnel bore were recognized as a significant, but indeterminate risk. This paper presents a case history of the owner’s contracting strategy for risk assumption and management of the boulder impacts on the project. Actual conditions encountered during construction and contractual adjustments made to address problems are reviewed, and recommendations for future contracts are included.

Jan 1, 2003

By Omar A. Muhtadi

6.1 INTRODUCTION The three most critical factors in successful heap leaching operations are: • The methods employed to pretreat ore (i.e, crushing and agglomeration); • Placement of ore on the leach pad (heap building techniques); and • Wetting of the ore with cyanide (solution application techniques). Improper execution of any of these initial steps may result in a substantial sacrifice of total metal extraction or, in the worst case, in project failure. Ore preparation in terms of crushing and agglomeration was discussed in Chapter 5; this chapter therefore focuses on commonly employed techniques for heap construction and solution application. The main objective of heap construction is to obtain the most homogeneous heap possible. "Channeling" of leachate in heaps with preferential seepage paths leads to preferential leachate distribution and uneven/incomplete extraction. The two main contributing causes of channeling are inadequate attention to heap construction and uneven solution application. These pitfall s can best be avoided through a knowledge of the various techniques available and the applicability and success of these techniques with various ore types and site conditions. The remainder of this chapter provides a discussion on these two subjects. 6.2 HEAP BUILDING TECHNIQUES Successful heap building techniques vary with the type of ore and, since no two orebodies are exactly alike, some slight modifications are usually necessary for each specific project. However, it is possible to generalize in terms of the appropriate techniques to be used with ores having similar characteristics. This section discusses the three most commonly used methods of heap construction and provides some guidelines with regard to ore types, construction constraints, and lift height parameters for each of the three. 6.2.1 Run-of-Mine Dumping and Dozing The run-of-mine method of heap building can only be used with ore of a highly silicious nature (i.e., ore which will not generate a large amount of

Jan 1, 1988

By R. V. Hunter, J. F. T. Agapito

Introduction Significant increases in extraction ratio on the order of 6% to 8%, equivalent to as much as 142 t/m (48 st per ft) of panel, have occurred at the Big Island trona mine during the last five years with the help of a practical rock mechanics program. This increase in resource recovery also has contributed to improvements in productivity. Both conventional and continuous machine mining have been used to mine two flat-lying trona beds at depths of 250 m and 260 m (820 ft and 853 ft) in the Green River Formation in southwestern Wyoming. Conventional room-and-pillarmining originally was conducted in panels with extractions of 5 8% to 60%. The use of yield pillars has allowed the panel extraction in increase to 66%. Continuous machine mining was introduced, with a 64% extraction ratio using long, narrow pillars and wide rooms. Further improvements in resource recovery seem feasible in light of present mining experience. The rock mechanics program consisted of field instrumentation to determine the pillar and roof response hole locations. to mining and computer modeling to evaluate the stability of various layouts, which were then adopted for mining. Mining background Stauffer Chemical Co.&apos;s Big Island mine and refinery are located 40 km (25 miles) northwest of Green River, WY. Underground mining operations supply trona, a sodium mineral, to the refinery to produce soda ash. The room-and-pillar method is used to mine two 3 to 3.6 m (10 to 12 ft) thick, flat-laying seams at depths of about 250 to 260 m (820 to 850 ft). Mine production in 1986 was 2.3 Mt (2.5 million st). These were supplied through both conventional and continuous machine mining sec-

Jan 1, 1989

By Van Zyl Brink

A longwall-based coal mine in Australia, referred to in this paper as AusMine Colliery, experienced windblasts resulting from goaf falls. Windblasts were the cause of serious injuries and threatened the continued operation of the mine. A microseismic early warning system was installed and a significant success rate in providing early warning of large roof instability resulting in high velocity windblasts, has been achieved. Early warning of goafing is accepted as an operational tool on the mine. Severe demands are placed on the operator in terms of &apos;real time&apos; interpretation. The development of an expert system allowed for a probabilistic approach to achieve automatic alarms. This paper will quantify the success, failure and false alarm rates achieved by manual operation and automatic expert system-based decisions making, respectively.

Jan 1, 2002

By R. J. Matetic

The impact of longwall mining on the local hydrological regime has become an important environmental focal point. Unfortunately, only a few studies have addressed the timing and range of well fluid level fluctuations and the associated ground movement. Furthermore, even fewer studies have determined the influence of longwall mining on water quality. The U.S. Bureau of Mines is providing insight into this environmental concern through a program of field case studies. One such study was conducted in Cambria County, PA where five observation water wells were drilled above two adjacent longwall panels. In this study, three wells were completed as nested piezometers and the remaining two served as producing wells. The piezometers were positioned along a line oriented subparallel to the longwall face and were located at the centerline of each panel and over the intervening chain pillars. The piezometers were designed to monitor fluid level fluctuations in both shallow and deep water-bearing zones. Slug tests were conducted before and after mining to characterize changes in hydraulic conductivity of the respective water-bearing zones. Pressure transducers and data loggers were installed to provide continuous fluid level fluctuation data as mining developed through the study area. The producing wells were drilled to provide water quality information. One well was located directly above the centerline of a panel and the other was positioned over the panel&apos;s set-up rooms. The wells were designed to simulate domestic use and were produced daily, for four hour intervals, throughout the study. Samples of the produced water were collected before and after mining progressed through the area. In addition, an array of monuments was installed near the study wells and was periodically surveyed to characterize mining-induced surface deformations. This study shows that: a) the observed changes in ground water chemistry did not affect the potability of the water; b) short-term major water level fluctuations occur at the approximate time of undermining; and c) water level recovery begins before the process of subsidence is complete.

Jan 1, 1986

By G. Simmons

Santa Fe Pacific Gold Corporation (SFPGC) conducted pressure oxidation pilot plant studies at Hazen Research, Inc. on the Twin Creeks refractory carbonaceous gold ores during 1993 and 1994. Previous laboratory investigations demonstrated very good gold recoveries of 90 to 95%, using CIL cyanidation after batch pressure oxidation. However, results from the pilot plant showed that several ore types responded very poorly, with gold extractions of only 45 to 75%. Since these poor recoveries were unexpected, pilot plant testing was suspended for approximately four months while extensive research activities were conducted to determine the cause(s) and identify potential solutions. This paper describes the batch and pilot plant test results, the research activities that eventually identified the cause of the gold recovery problem, and the final semicontinuous and continuous pilot plant operations that confirmed possible solutions.

Jan 1, 1997