Search Documents

By Daniel Hodouin, Antoine Berton

Mineral processing plants are monitored and controlled using measurements that are usually processed by on-line material balance calculation techniques. However, gross errors, due to sensor biases or failures, may corrupt all the process variable estimates. On-line gross error detection methods are required to ensure efficient mass balance evaluation. In the proposed approach, material imbalances and raw measurement corrections are tested by statistical techniques designed to detect and isolate sensor problems.

Jan 1, 2000

By Jim Johnson

The purpose of this paper is to summarize and discuss a variety of site specific conditions which are typically evaluated as part of the engineering design process for heap leach pads, solution control ponds, and associated facilities. The following sections will focus primarily on the topographic, climatologic, hydrologic, and geotechnical evaluations critical to selection of heap leach sites, and selection of a preferred heap leach configuration or method. Other important considerations in the design of a heap leach project, including evaluation of ore properties and leachability, pregnant solution processing requirements, spent ore neutralization/disposal requirements, and other anticipated reclamation requirements are beyond the scope of this paper are not addressed in any detail.

Jan 1, 1998

By David K. Parrish, Duane A. Labreche

Analyses of jointed, cracked, and fractured rock masses are needed in a variety of applications, including estimates of reduced elastic modulus for damaged rock, estimates of permeability changes as a function of stress changes, and estimates of relaxed regions due to excavation. A numerical model of a jointed rock mass, the compliant joint model, was used to study the response of a jointed rock mass near a circular excavation. The joint constitutive model was linear elastic in shear and nonlinear elastic in the relationship between normal stress and joint closure. Initial stresses were geostatic and representative of stresses in a granitic jointed rock mass approximately 300 m deep. The joint properties were based on values that are representative of joints in granite. The results from numerical simulations were compared with analytical results for stress near a circular opening in an elastic medium having reduced Young's Moduli to simulate jointing effects on the rock mass. The differences in response between the two models resulted from the differences in the symmetry of elastic properties, the shear modulus of the continua, and the constitutive relations in the two models. For example, the non- linear anisotropic elastic continuum described by the compliant joint model resulted in vertical stress concentrations near the side of the circular opening that were 25 percent higher than the vertical stress concentrations in an isotropic linear elastic medium. The equivalent Young's Moduli in the vertical and horizontal directions of the compliant joint continuum deviated by as much as 50 percent from the values assigned to the modeled region prior to excavations. The perturbations of the elastic Young's Moduli extended to distances of two to three radii from the opening.

Jan 1, 1986

By John E. Urosek, Timonthy R. Watkins

Room and pillar mining accounts for approximately 73 percent of the active gobs used in the United States in 1993. The Mine Safety and Health Administration conducted field investigations on six different types of bleeder systems used to ventilate areas mined by room and pillar methods. This paper discusses investigations that were conducted at mines using four of these systems.

Jan 1, 1995

By Andrew Hall

Many Latin American countries are facing a scarcity of water. As such, infrastructure decisions are quite different from those made in parts of the world that experience a positive water balance. In the latter case, the water treatment approach tends to be ?treat and discharge.? For Latin American regions facing the challenges that go with a negative water balance, the focus is on resource optimization and reuse. Historically, the water challenge has had a significant impact on economic development in Latin America, especially in sectors such as mining, where water usage is high. At the same time, countries such as Chile and Brazil are major development targets for mining and oil and gas operations. Given the water supply challenge, industry is increasingly turning to technologies and processes that maximize water recovery and reuse. With sulfide precipitation and ion exchange water treatment processes for example, it is possible to treat and recover more than 99 percent of water for reuse onsite. These technologies have been applied successfully in other regions of the world where water conservation practices are essential to economic survival.

Jan 1, 2012

By R. E. Johnson, L. V. Araújo, B. R. Palmer, L. M. Abrantes, G. W. Warren

The behaviour of chalcopyrite - mineral specimens and a Portuguese concentrate - in 2M chloride solutions prepared from hydrochloric acid and sodium chloride, has been characterized by cyclic voltammetry. The study has shown the influence of the potential and of the presence of impurities in the reaction schemes and their relative extent. The dissolution of chalcopyrite concentrate under potentiostatic control has been investigated and found to confirm the effect of the selected potential on the surface modification/rate of dissolution. An attempt has been made to correlate the information obtained with the response of the concentrate electrode to constant current treatments.

Jan 1, 1993

By P. R. A. Andrews, G. Heinrlch, V. I. Lakshmanan

The paper describes a simplified method to chemically modify the surface of industrial mineral fillers. Four industrial mineral samples were taken from feedstock of commercial fine grinding operations. These samples were ground in bench scale ball mills and in the presence of various organic solvents. The ground products were measured for particle size distribution, surface area, surface chemistry by oil absorption and degree of organicJminera1 bonding. Where appropriate, the ground products were compared to commercially available surface modified, industrial mineral fillers.

Jan 1, 1990

By D. Hong, K. N. Han

The leaching behavior of rhenium in ammonium iodide solutions with iodine as oxidant was studied. Experiments were carried out in an autoclave to investigate the effects of stirring speed, temperature, solution pH, and iodine and iodide concentrations on the dissolution of rhenium. It was found that a high temperature and a high solution pH were essential for the efficient leaching of rhenium. The dissolution rate was found to be dependent upon the concentration of iodine and iodide. It was concluded that the dissolution of rhenium under the conditions studied was controlled by the mass transfer of iodine with an apparent activation energy of 15.8 kJ/mole.

Jan 1, 1999

By J. Brinen, D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study copper ion adsorption, and its effect on subsequent sulfide collector adsorption, on pyrite and pyroxene minerals under flotation related conditions. Copper was found to adsorb on both of these minerals and cause enhanced sulfide collector adsorption. The distribution and depth profile of copper and collector on these mineral surfaces were obtained by using SIMS in the imaging mode. The results of this study have provided a valuable insight to understanding pyrite and gangue flotation observed frequently in operating plants.

Jan 1, 1995

By Kenneth R. Miller

Surface mine equipment operators in the Campbell County region of Wyoming's Powder River Basin have found new ways of solving old problems. Technology, experience, competitive pressures and an increasing grasp of economies of scale have driven mine operators, equipment manufacturers and suppliers to specialization of applications. In economic terms, today's coal price of $4.95/t ($4.50/st) equates to $2.53/t ($2.30/st) in 1980 terms - an incomprehensible value at that time. This article describes some examples of change and adaptation made by Powder River Basin coal operators in overburden stripping equipment and techniques. It focuses on the evolution of the design and use draglines, shovels, trucks, scrapers and dozers.

Jan 1, 1998

By V. G. Matziaris

The differentiation between saturated and un-saturated soils becomes necessary due to basic differences in their nature and engineering behavior. The most important difference is the existence of a suction zone, above the water table, in unsaturated soils. Pore water pressure in this zone is always negative and the shear strength is greater than the one in saturated soils. This is due to an occasional and apparent component in the Mohr-Coulomb equation, which appears in unsaturated soils. In slope stability analysis of unsaturated soils, the factor of safety increases due to this occasional cohesion component of the shear strength. However, the suction zone tends to disappear because of rainfall. In these cases the factor of safety decreases and eventually the slope may fail. In this article, a parametric study of the effect of suction zone fluctuation due to precipitation in slope stability is examined. For this purpose a Combined Hydrology and Stability Model (CHASM) has been applied.

Jan 1, 2005

By L. Wade, D. R. Pearce

A detailed account is given of the spectral ratio laboratory method for the determination of seismic velocity and attenuation through rock cores under simulated in-situ stress conditions. An account of a computer program called AUTOQ is described for automatic processing of a complete set of laboratory results. Some of these results are shown and discussion is directed to- wards the suitability of in-situ velocity or attenuation measurements in determining rockmass condition or stress regime.

Jan 1, 1996

By J. Loredo

Asturias, in northern Spain, emits 18 Mt CO2/year to the atmosphere, which supposes the biggest industrial CO2 emissions in the country. In order to avoid CO2 emissions to the atmosphere, keeping the availability of energy from fossil fuels, background studies focussed to the selection of favourable sites for CO2 geological storage are necessary. In Asturias, the options for CO2 geological storage are sequestration in deep saline aquifers or sequestration in unexploted coal beds. In the area, there is the biggest coal basin of the country and a great Palaeozoic sedimentary basin with appropriate silicoclastic or carbonated reservoirs and impermeable caprock for CO2 geological storage, located in proximity to thermoelectric power plants and other sources of CO2 emissions. All evidences suggest that CO2 storage in deep aquifers is the most interesting option but a legal planning and a technical regulation are still to be done. The possibility for CO2 sequestration in coal beds is modest and associated to the CBM commercial exploitation. It is necessary to have in mind that the feasibility of CO2 geological storage in Asturias apart of technical factors will depend on price of CO2 ton, legal conditioning and possibility to apply emission rights to projects.

Jan 1, 2006

By Gary S. Brierley, John W. Critchfield

This paper is a case history of a subsurface exploration program conducted for a system of sewer tunnels in upstate New York. The focus of the discussion is a non-technical outline of how the exploration process was organized to efficiently produce a large body of geological and geotechnical data. A brief description of the project and geological setting is provided, the scope of the exploration program is summarized, the logistics of collecting, processing and reporting subsurface data is outlined, and recommendations for management of explorations applicable to any rock tunnel are provided.

Jan 1, 1983

By Mary-Lee Athorn, David A. Barratt

An opportunity to compare the performance of different tunnel boring machines (TBMs) operating in similar rock conditions occurred during the construction of a major water scheme in the UK. The principal objectives of this study were: (i) To collate, analyse and present the data available for the four TBM drives of the Kielder Aquaduct Scheme in terms of the tunnelling system performance and the downtime experienced, particularly where these were influenced or controlled by geotechnical parameters. (ii) To isolate the major sources of machine downtime and highlight those aspects of the tunnelling system that critically affect tunnelling progress rates (iii) To determine, by statistical techniques, relations between TBM performance and rock properties.

Jan 1, 1986

By D. W. Park

Underground openings resulting from coal mining activities have been a serious cause of subsidence problems in the Warrior coalfield of Alabama, which is the 11th largest coal-producing state in the United States (National Coal Association, 1986). The problem will be even more serious in the future because 17 Gt (19 billion st) of Alabama's 22 Gt (24 billion st) of coal reserves are classified as an under- ground resource (Tolson et al., 1982). Subsidence data in this area has been scarce com- pared with other coalfields (Conroy, 1980; Dunrud and Osterwald, 1980; Gentry and Able, 1978; Hunt, 1979; King and Gentry, 1979). This paper discusses the results of a study of subsidence overlying two longwall mines that contrast each other. One of them (Mine #1) is a shallow longwall mine where the coal strength is very high, and the other mine (Mine #2) is extremely deep with a low strength of coal.

Jan 1, 1987

By Rodrigo Jerez

The mining business in general, and coal mining in particular, is exposed to frequent and significant swings in the business cycle. Marginal coal production enters the market place in a nearly perfect competition. It must be priced aggressively if market share is to be gained. The minimum price acceptable from the standpoint of the producer is reached at the point where total variable cost are recovered. Competition occurs as companies move to reduce their variable costs in an effort to cover some portion of their fixed costs at reduced market prices. Production planning and scheduling plays a critical role in reducing costs. Multiple scenarios based on changing market conditions require that competing firms have tools available to evaluate the economic impact of transportation, blending, and processing options. In certain applications, significant cost savings can occur as a result of blending or altering preparation levels. Linear programming provides a tool with which to evaluate options and acts as a like between the mine plan and marketing decisions.

Jan 1, 1992

By Steven W. Hunt, Ronald E. Heuer, Safdar A. Gill

A 3.3 m (11 feet) diameter, 51 m (168 feet) deep temporary steel casing which had been sunk within glacial soils buckled and collapsed on July 29, 1985. The collapse occurred at the CT-8 Dropshaft site in Milwaukee while two workmen were contact grouting outside the casing in an attempt to stop groundwater inflows through a bottom plug. This paper describes the soil and groundwater conditions at the site, the casing design, the method of shaft construction, and probable causes of the buckling failure. Specific aspects of the paper include: slurry method of shaft excavation and casing installation, soil creep, earth pressure due to three dimensional arching, and buckling strength of a casing surrounded by slurry rather than grout and firm soil. The paper should be of interest to designers and constructors of temporary ground support systems for deep shafts.

Jan 1, 1995

By S. K. Kawatra, T. C. Eisele

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. To reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, because different measures are required for reducing entrainment, locked particle flotation or true hydrophobic flotation. In this paper, evidence is presented that suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite; instead, the bulk of the recovered pyrite results either from simple entrainment or from being physically locked with floatable coal particles.

Jan 1, 1993

By G. G. Marino

Little comprehensive information has been reported on the behavior of room-and-pillar mines. The objective of this paper is to present case data on mine failures in the Illinois basin for use in practice. Presented are results of an ongoing study and details on the site characteristics of cases where sags have developed on the surface. Site data are reported to show the geologic, mining, and sag conditions that existed. Sags mainly develop from pillar, floor, or pillar-floor failure. The character of the sags depends upon the type of mine failure as well as the overburden response.

Jan 1, 1989