Search Documents

By J. L. Hendrix, M. Ahmadiantehrani, G. Ramadorai

The concept of hypochlorite treatment prior to cyanidation in the heap leaching of low grade carbonaceous gold ores is discussed. Laboratory column leach tests using a low grade carbonaceous ore were performed to investigate the effects of pH, hypochlorite consumption and concentration, and bed height on total gold extraction. At high pH, hypochlorite stability increases and thus, hypochlorite consumption decreases. At room temperature, total gold extraction is proportional to hypochlorite consumption. However, at some point additional hypochlorite consumption does not increase gold extraction. Gold recoveries of 10% and 80% are achieved at 12 and 167 lb/ton hypochlorite consumption, respectively. Increasing hypochlorite concentration increases the rate of extraction. For a given hypochlorite consumption, gold extraction increased with decreasing ore bed height. Finally, using calcium hypochlorite results in higher gold extraction than using sodium hypochlorite at a fixed hypochlorite consumption.

Jan 1, 1992

By I. F. Walder

Mill tailings from skarn-type base metal deposits were studied in order to ascertain potential element mobility in response to weathering. Hypogene ore minerals are sphalerite, galena, and chalcopyrite, showing minor supergene oxidation to smithsonite, cerussite, and covellite. Gangue minerals are pyrite, pyrrhotite, magnetite, hematite, andradite and grossular gamet, hedenbergite, calcite, ankerite, and quartz. Foremost of the eleven tailing piles studied, the hypogene sulfide minerals show no or only incipient post-mining oxidation. Iron oxides and hydroxides form the main oxidation products in the tailings and are enriched in heavy metals. A distinction between pre-and post-mining oxide phases may be obtained based on petrographic observations which distinguish whole-grain versus partial grain replacement. Zn and Cd do not appear to be enriched in the weathering derived oxidation minerals and will be more easily leached from the tailings than other metals.

Jan 1, 1994

By D. E. Ranta, M. G. Hester

The ore reserve modelling of stratiform uranium deposits to be mined by selective underground mining methods must be done with consideration of the erratic nature of the ore-forming processes that produced the mineralization. Estimation methods that model the uranium grade as a smooth transition between high-grade and low-grade drill hole intercepts tend to greatly overestimate the ore tonnage. Care must be taken to first establish realtistic ore pod geometries and then estimate the grade of the reserve units within the pods.

Jan 1, 1992

By Pentti Kallio

From the aspect of economic feasibility of mining, ineffective use of expensive mechanization investments is becoming a problem. In many cases, the machinery is in operation only 50 - 60 % of the total working time. The lost time when the machines are idle means a considerable over-investment in machines. The lost time, with LHD equipment in particular, accumulates from the following constituents: - the needs of the person operating the machine trips to the work site, lunch, coffee and other breaks, want for comfort, etc. - deficiencies in the monitoring and control systems for machine operation waiting periods at loading and unloading stations, unnecessary and erroneous actions, inefficient work, etc. - deficiencies in the machine condition monitoring system , and inefficient service and maintenance work The data transfer and computer technology of today provides means for resolving problems in several areas - including the area of underground loading operations. In the paper those areas of automation and data handling are considered which make possible an improvement in the usage and monitoring of LHD equipment. These fields are: remote control of equipment, use of TV cameras and monitors in remote control, locating equipment and data transfer down the mine, measurement of the load and the data storing system, systems for following the condition of the equipment, unmanned operation of equipment.

Jan 1, 1989

By R. R. Oder, R. J. Gray

We report measurements of the effects of rank, type, and grade of coal on grinding energy and grinding media consumption in a Pitt Mill. The rank of coal has a greater effect on grinding energy than does coal type. The effect of coal grade on grinding energy depends upon the relative grindability of the mineral matter and of the hydrocarbon components of the coal. The mineral matter is primarily responsible for abrasive media wear in a Pitt Mill. The widely recognized HGI test for coal breakage may yield misleading results, particularly for multiple-banded bright and dull coal where the screening procedure used in sample preparation favors the testing of the hardest coal fraction. The work reported here indicates that the Pitt Mill, which grinds the whole coal in a single stage and which yields easily interpreted results, is an excellent candidate for testing coal pulverization characteristics including energy requirements and equipment wear. The measurements of the effects of coal characteristics on grinding energy and on media consumption have been used to estimate the cost of fine grinding in a Pitt Mill. The results, based on a conceptual level evaluation of grinding at the rate of 1 TPH, show that there are trade-offs possible between the cost of energy and cost of media consumption which involve choice of grinding media size. The use of fine-size grinding media to lower grinding energy and to increase throughput can be deceptive because the total cost of grinding must consider both energy and media consumption.

Jan 1, 1992

By Alexandr A. Abramov, Svetlana M. Angelova, Oleg P. Maljuk

In this paper the effect of the ratio of grinding and grindable size classes (ore lumps, particles and grains) and the guantity of intermediate size classes in the feed of the primary wet autogenous grinding "Cascade" mill is studied and the features of the influence of these factors on the mill capacity are shown. On the basis of the experimental data from Lebedinsky mineral processing plant, where magnetite guartzites are processed, a coefficient of the "total ratio of size classes" in the feed of 9x3 m "Cascade" mill was estimated. It helps to get an evaluation of the effect of ore size classes ratio in mill media on the mill capacity and to work out some ways for its optimization in closed or semiclosed technological circuites of primary autogenous grinding. The operation of the specific energy effects for some intermediate size classes, removed from the mill as circulating load, is proposed to improve its efficiency before regrinding in "Cascade" mill and decrease negative influence of such classes accumulation in the mill media.

Jan 1, 1995

By P. T. Kane, O&apos

Capital and energy are the dominant cost factors in nickel production from laterites. Since the 1973 energy crisis, pyrometallurgical developments have been oriented towards lower cost sources of energy and higher grade ores and hydrometallurgy towards higher recoveries and greater flexibility in types of ores treated. Energy recuperation offers some potential, but at a price. 'The lower energy acid leaching process is indicated to have the greatest potential, particularly with its inherently high cobalt recovery.

Jan 1, 1979

By H. Bernatowicz

The Nucoalyzer (On-Line Nuclear Analyzer) is a new method recently made comercially available for monitoring the elemental composition of a process stream. Applications for the Nucoalyzer include grading ore on a conveyor belt before or after it has gone through primary crushing, monitoring the slurry being transported in a pipe to the concentrator, and monitoring the stream of concentrate or the tailings from the concentrator. The Nucoalyzer may also be used at the smelter to monitor elements in the feed that include copper, sulfur, iron and silicon where a uniform feed is desired. The advantage of the Nucoalyzer over most other techniques are (a) it performs the measurement directly on the process with no sampling necessary, (b) the analysis can be performed on streams of particulate and slurries, and (c) the system does not have to make contact with the material it measures. These Nucoalyzers are operating at coal fired power plants and several more are about to be placed in service. This paper discusses the principles of operation of the Nucoalyzer, our experience in the field, application of minicomputers to data reduction, and potential applications in the ferrous and non-ferrous industries.

Jan 1, 1982

By Juan Eduardo Barrera

SUNNARY AND CONCLUSIONS Argentina presents to the foreign and local investors a mineral wealth that is largely unexplored, untested, underdeveloped and therefore incompletely evaluated. In view of the above, the new administration of President Raul Alfonsin through its Department of nines has designed and implemented a strategy ( Plan de Expansión Ninera P.E.M.), whose main objective aims at improving the "investment climate" in the sector. It is the Government's basic intention to apply the Mining Promotion Law with responsibility but with generosity to encourage the attraction of investment (local and foreign) to the sector. The establishment of a Data Bank system to evaluate possible new potential ore mining developments will help to connect the owners of potential projects with investors outside the sector. Argentina has an interesting gold ore potential. Estimated reserves of individual projects already known amount to almost 300 tonnes of gold for potential production. The government strongly believes and present information indicates that more systematic exploration has to be undertaken in the Jurassic areas that almost cover the whole of Patagonia. Two recent gold discoveries (Angela in the Chubut province, and Cerro Vanguardia in Santa Cruz province) indicate the potential of this area.

Jan 1, 1988

By Jerry C. Tien

This paper investigated the airflow pattern in the working face area during a cross-cut development. The study used a 10:l scale face model and a mock continuous miner. Results showed that keeping up the line curtain is essential in order to avoid recirculation and to control respirable dust and methane, in the face area.

Jan 1, 1989

By Nick Barton, Khosrow Bakhtar

Two plate load tests of 1 m2 area were per- formed in a pressure tunnel at the Rocky Mountain Pumped Hydro Project. Reaction for the 250 tons loading in this 10.5 meter diameter tunnel was provided by deeply anchored, diverging rock bolts, eight per load frame. Pressure build up to 2.5 MPa was provided by circular flatjacks. Rock deformation was recorded at depths of approximately 0.3, 0.9, 1.2, 1.8 and 3.3 meters using axially located multiple position borehole extensometers. The tests were performed in representative units of massive shale and thin to medium bedded siltstone. Stress was built up in four equal steps to 2.5 MPa, held constant for one week for creep monitoring, then unloaded, reloaded and unloaded over a period of one day. The most deformable unit was the massive shale which exhibited 1.3 mm of permanent deformation at the surface after the first loading and unloading cycle, which included 0.36 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 2.6 mm, following a maximum deformation at the surface of approximately 3.6 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 0.4 GPa when loading, and 0.3 GPa when unloading. The thin to medium bedded siltstone exhibited only 0.17 mm of permanent deformation at the surface after the first loading-unloading cycle, which included only 0.05 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 0.27 mm, following a maximum deformation at the surface of approximately 0.53 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 6.2 GPa when loading and 21.9 GPa when unloading.

Jan 1, 1986

By Russell Frith

A review of published literature reveals case histories whereby the entire periphery of a coal pillar has “burst” out as a single event during first workings, the associated energy and material release causing significant damage to adjacent roadways and any equipment/infrastructure located within said roadways. Such events are distinct from coal burst events during first workings such as that at the Austar Mine in 2014, or those linked to overburden bumps related to either horizontal stress-driven slip along major faults and/or thick, massive strata units in the overburden or floor of the coal seam.

By I. Longson

Maintaining control over underground environmental conditions in the United Kingdom is increasingly dependent on the contribution of underground booster fans. Given the recent trends of higher rates of production from a fewer number of coal faces with higher levels of mechanization and higher power consumption, the effect has been to place a greater load on the mine ventilation system. This has increased the scale of potential problems that may arise should any of the main ventilation control devices not perform at the required full duty. This is particularly true for underground booster fans. Major changes occur in the main ventilation parameters on the stoppage or restart of a booster fan which results in a temporary loss of environmental control. This paper analyzes the impact of such events and details a mathematical model thar has been developed for a single-mesh circuit containing a main and a booster fan. Predictions based on this simple model are presented and discussed with particular reference to the energy changes occurring within the ventilation system immediately following a booster fan stop or restart

Jan 1, 1995

By Wang Xifu, Zhang Daxian, Zhang Youdi

In mine haulage system, the surge bunker or stockpile installed between two facilities can raise the system production capacity. The arrangement of surge bunker has great relation with the capability development of the whole haulage system and the economic benifit. In the haulage system, surge bunker plays a role of surge capacity, accident capacity and technology capacity. In this paper, the variation of the material in surge bunker is analysed while the mine haulage system is working, the calculation method of the whole output is raised. With the goal of the maximum system output, the method of deciding the rational size of surge bunker is put out. In case study, the system output in Huolinhe surface mine is calculated, thus the rational size of surge bunker in huaulage system is decided.

Jan 1, 1996

By C. C. Harvey

Based on resource studies in many developing countries, four categories of industrial clay resources are recognized as precursors to development strategies. Category I: High quality, high technology clays requiring major investment for large tonnage international markets. Category 2: Unique specialty clays requiring advanced technologies for small tonnage niche markets. Category 3: Lower technology, moderate quality clays, predominantly to supply local markets. Category 4: Low quality clays requiring little or no processing. Projects with Categories 1 and 2 clays require extended development times (green field to investment decisions) with significant pre-development investment, while projects with Categories 3 and 4 clays require shorter development timetables and lower levels of investment.

Jan 1, 1998

By T. J. Kim, S. Suh

The purpose of this paper is to evaluate overall prospects of the export market in the Pacific Rim for Illinois steam coal in terms of recent changes in global socioeconomic factors. To pursue this objective, three factors affecting the prospects of Illinois coal in the Asian market were selected for detailed analysis: quality requirements of imported coal, particularly those of the Japanese market; import controls and regulatory factors; and transportation factors affecting the export of Illinois coal. Based on these analyses, alternative long-term strategies are suggested for promoting Illinois coal export in the Asian market.

Jan 1, 1988

By Bekta? Uz

Istanbul is the bigest metropolitan city of Turkey with more than 15 millions of population and construction activities are steadly increasing with respect to that increase in population. In this papaer petrographical, physico-mechanical properties of natural aggregate mines from west, (Tekirdag) to East, Izmit (Gebze) 'will be summarized in connection with the concrete production. However the locations suitable for aggregate production in these area as; Paleozoic aged sandstones (Ayazaga, Cendere, Mahmutbey areas), Permb-Carboniferous aged limestones (Cebeciköy area), Triassic limes tones (Ömerli-Gebze areas) and Eosen limestones (Çatalca area), Plio-Quaternary aged volcanic basalts (Tekirdag, Çorlu, Beykoz areas). Plio-quaternary aged, fine grained aggregates within sandy formations are mined in Silivri-Sinekli area, Catalca-Ormanali area, Agacli-Akpinar (Kemerburgaz area) and Sile-Karakiraz-Sahilköy areas. Sandstones mineralogically contain mainly of Quartz+Feldspar and less amount of Mica (biotite+muscovite) rich with slica content and sedimentary origined. Especially limestones are cryptocrystaline textured, unique mineral composed of calcite and secondary have Dolomite ± (Quartz+Albite). Basalts are microlitic textured and contain Olivine+Pyroxene+Plagioclase. Chemically basalts rich with Fe and Mg and also volcanic origined. Sands are fine grained natural aggregates mainly contain semiangled, rounded minerals and rock fragments. Mineralogically have Quartz + Feldspar ± pyroxene+ ambhibole ±garnet and less amount of epidote ± magnetite ± hematite. Different rocks, used in aggregates such as limestones, sandstones-sands and basalts, supply varied concrete strength because of their mineralogical composition and characteristics of textures. Moreover, Basalts (Karatepe area) are good example for the higgest concrete strength (1017-1895 sc; kg/cm2) in our study area because of their clambed mineralogical apperance such as intersertal texture. As the result of extensive field and comparative laboratuary studies, the effect of petrographic, physical, mechanical properties of the aggregates on concrete srtength is extensivelly discussed in this paper.

Jan 1, 2005

By D. J. Murdock, Wyslouzil, I. M. Flint

The highly competitive nature of the international iron ore market has forced producers to improve the quality of their pellets. The demand for low-acid pellets suitable for direct reduction has resulted in an increase in the number of plants utilizing reverse froth flotation for silica reduction. Column flotation is being favored for this service because of low capital and operating costs and improved metallurgical performance compared to conventional flotation cells. This paper describes the benefits of column flotation and discusses some important aspects of circuit design.

Jan 1, 1995

By George Munro

Heavy water inflows of up to 1350 1/sec in the 19.6 km Moawhango-Tongariro Tunnel section of the Tongariro Power Development Scheme in New Zealand gave rise to severe operating problems, particularly in the equipment stripping stage when pumping installations had to be removed. Due to the necessity to commence stripping from the upstream side the contractors. Codelfa-Cogefar (NZ) Limited, took the decision to install a steel bulkhead some 5000m in from the lower. Tongariro, portal. The article lists the considerations taken in the placement of the bulkhead, and gives details of its design, installation and final removal. A brief description of the geology of the tunnel. together with water flow sources, rates and pressures is also included.

Jan 1, 1981

By David I. Dr. Hoyer

The Hicom mill is a conical mill in which a ball or autogenous load tumbles within a high-intensity acceleration field. An autogenous Hicom mill with a power density of about 1100 kw/m3 and a volume of just 4 litres reduced a 50 m quartzite feed to 90% passing 38 microns at a feed rate of 160kg/h (in closed circuit with a hydrocyclone). Batch tests have identified fracture, chipping and abrasion breakage mechanisms at pebble sizes of 5 to 50 mm. The special behaviour of the load in Hicom mills was exploited to develop a novel technique for estimating steady state autogenous load size distributions.

Jan 1, 1992