Search Documents

By P. M. Jones

Introduction The success of in situ leaching depends upon: • maintaining adequate injection and recovery flow capacities in wells, and • distributing leach solution effectively to contact and leach ore minerals within the target zone. Solution balance is an important indicator of the capability of a particular in situ hydrologic design to efficiently and effectively control and distribute leach solution within the target ore zone. As part of ongoing hydrological investigations into in situ leaching, the US Bureau of Mines (USBM) is studying factors affecting solution balance in an unsaturated copper ore deposit at the Cyprus Casa Grande Mine. The purpose of this study is to assess the effect of hydrogeologic features and in situ operating conditions on changes, during leaching, in: • solution storage within the deposit, and • solution balance. At the Casa Grande Mine, In-Situ-Leaching Test Facility, solution balance estimates are obtained for 10 selected intervals during 17 months of leaching under a variety of well configurations, pressures and flow conditions. Operational and geological description The Casa Grande Mine is located 32 miles south of Casa Grande, AZ. The mining area is within the Casa Grande Deposit, a porphyry copper stock consisting primarily of an intensely-fractured, granodiorite cap overlying a copper sulfide base. As a result of mine dewatering activity, unsaturated conditions existed in the deposit prior to leaching (Schmidt et al., 1990; Friedel and Schmidt, 1991). No groundwater was present in any of the in-situ-leaching, test-facility wells after drilling and prior to leach solution injection. Also, no ground water seepage occurs in the test-facility drift. The Casa Grande, In-Situ-Leaching Test Facility consists of 58 injection and recovery wells collared in an underground drift. The wells were drilled at various angles into the granodiorite deposit in a series of 15 divergent fans (Fig. 1). The fans are 12.5 ft apart and lie parallel to one another between the 900- and 1100-level drifts. Each fan contains three to five wells drilled at angles ranging from 6° to 89° from the horizontal. The wells can operate in an injection or a recovery mode. Currently, 36 flow sensors and 28 pressure transducers (part of a hydrologic, data acquisition system) are used to continuously monitor injection-well flow rates and pressures.

Jan 1, 1993

By John K. Hollmann

The use of the direct method of determining coal methane content has grown in the last decade from a research technique into a practical coal exploration tool. However, the literature available on the subject is somewhat lacking in site-specific guidance and observations on the conduct of the method and the use of the resulting data. This study discusses some practical lessons learned in conducting a large scale direct measurement project at an operating mine, describes the initia1 interpretations and uses of data from the project, and presents observations from subsequent mine operations into the success and limitations of using direct measurement data in mine planning. The site studied is in central Pennsylvania on the Appalachian Plateau and includes coal seams in the Allegheny series.

Jan 1, 1987

By P. V. R. Bhaskar Sarma, P. K. Sahoo, G. Roy Chaudhury

A process was developed to treat an ammoniacal leach liquor containing zinc using Di (2-ethyl hexyl) phosphoric acid (D2EHPA) as the extractant. The objective of this work was to develop a process package for the treatment of complex sulfide leach liquors. Zinc extraction could not be carried out directly from the ammoniacal solution in mixer-settler units because of crud formation and low extraction efficiency. After neutralizing the free ammonia with H2SO4, the extraction efficiency was only about 40%, due to the high concentration of (NH4)2SO4. To decrease the (NH4)2SO4 concentration, the free NH3 was steam stripped, and the resultant liquor was subjected to zinc solvent extraction. An extraction efficiency of 98% could be achieved by controlling the equilibrium pH. Stripping studies were also optimized after removing ammonia from the zinc-loaded organic. A continuous 100-hr operation that included extraction, scrubbing and stripping, was carried out successfully.

Jan 1, 1995

By Zhen-xing Diao, Feng Zhao, Ya-dong Xue

"Two important aspects of excavation performance of TBM are advance rate and cutter replacement/ring consumption, which is closed to the cost and construction duration of the project. To achieve this, a database of TBM parameters and the geological-geotechnical conditions during the excavation of Yinhanjiwei was compiled and analyzed. Relationships between different geological and TBM operational parameters were investigated. Results of analyzes show that there are qualitative correlation between Field Penetration Index (FPI) and rock geological parameters. And strong relationships between FPI and operational parameters are suggested. In this study, the cutter replacement and ring consumption were analyzed using statistical method for preliminary estimation in similar conditions. 1. ITRODUCTION Hard rock TBM is widely used in tunneling project nowadays because of its advantages to conventional drilling and blasting, especially in long tunnels. The biggest advantage is its high advance rate. However, rock conditions of tunnels are complicated. So TBM performance becomes a primary topic in tunneling engineering, which includes of rate of penetration, utilization, daily advancement, cutter consumption and so on. Many prediction models have been developed to estimate the TBM performance in the project planning phase. The most widely accepted and used models around the world are semi theoretical CSM model (Rostami and Ozdemir, 1993; Rostami, 1997) and the empirical NTNU model (Blindheim, 1979, Bruland, 1998).With increasing uses of TBMs in different ground conditions, an increasing number of researchers have developed new models in order to predict the performance of TBM more accurately in similar geological conditions.(Gong and Zhao, 2009; Hassanpour et al.,2009, 2010, 2011, 2014; Delisio et al., 2013; Delisio and Zhao, 2014)"

Jan 1, 2016

By Bekta? Uz

The study area is located between Orhangazi and Sapanca geographically known as Armutlu Peninsula (Figure 1). It is steep broken and mountainous with an area of 4000 km2. [ ] Economic marbles are investigated in regionally such as Orhangazi, Elmali, Menek?eyayla, Sapanca, Pamukova and they are seperated approximately 800 km2 (Figure 2). These marbles are massive, thick and dispersed as small sized outcrops in Armutlu Peninsula.

Jan 1, 2005

By G. A. Rowell, T. M. Barczak, J. C. Zelanko

The US Bureau of Mines conducted a multifaceted geomechanics research project at a bump-prone longwall coal mine in eastern Kentucky. This mine presented a unique opportunity to study coal mine bumps because the problem appeared to be confined to areas beneath a sandstone channel of limited areal extent. The Bureau's research plan sought to exploit the uniqueness of the site by monitoring strata behavior and longwall support reactions as the longwall face approached and passed beneath a sandstone channel. The study incorporated static pillar stress and strata deformation measurements, shield support leg pressure measurements and microseismic monitoring, as well as geologic mapping and the collection of observational data. Data collection was underway when a major coal bump occurred on the longwall face at the mine. Pillar behavior (load and deformation), shield loading and microseismic activity were monitored prior to, during and after the bump. Observations in the tailgate indicated that these pillars were failing prior to and following the face bump. Shield load data, evaluated in an effort to identify trends that could be used to forecast coal bumps, appear to provide a measure of the effectiveness of destressing operations conducted on the face (e.g. shot firing). Analyses of microseismic data revealed anomalous values associated with microseismic "energy" prior to the face bump. In addition, microseismic source-location data and underground observations provided some insight as to the sequence of pillar and face bumps.

Jan 1, 1992

By Lawrence F. Rooney

The wide distribution of limestone and dolomite and the decentralization of the depedent industries give the State Geological Survey a major role in the, development of these mineral resources. The amount of geological information necessary for efficient exploration is so large that few companies can afford to do the necessary basic field work or store the data. The state surveys fill these responsibilities and thus might be said to serve as the geological research departments of the limestone and dolomite industry. At the Indiana Geological Survey, the data of most value to limestone producers are in the form of unpublished measured sections, well records, cores, chemical analyses, directories, and geologic maps. Much of this information is published in summary form. The Survey also assists individual members of industry in exploration and evaluation of mineral deposits. In addition, a progressive State Survey provides the geological infor¬mation necessary for the development of new resources which do not appear to justify industry's own preliminary efforts.

Jan 1, 1966

By W. Blake, J. Mahaut, W. Hustrulid

Division II at Kamoto mine in Kolwezi, Zaire represents a transition zone between Divisions I and III where transverse and longitudinal cut-and-fill rooms were being mined. Because this transition zone had been geologically depicted as being badly faulted the mining in this division had been deferred to a future time. However, to increase production and to reduce mining costs by carrying out the mining of the 3 divisions simultaneously, it was decided to mine Division II. The mining research group of Gecamines was given the task of designing a mining geometry then testing this design in a full scale test. Based on an evaluation of the faulting and fracturing of the 2 parallel orebodies and on an extensive in situ testing program preliminary mathematical analyses were used to develop and evaluate room and pillar designs in the 35°-65° dipping bedded formations. Based on these analyses and the constraints of having to fit the design of Division II to grade into Divisions I and III in a logical manner, a mining geometry for Division II evolved. To test this design an instrumented room was excavated in the most critical area. The results of this full scale testing showed that the behavior of the roof and wall rocks were as had been predicted by finite element computer model studies which incorporated the material properties and results of the field testing. The room geometry design was both judged and observed to be stable, hence mining commenced.

Jan 1, 1977

By Paul J. A. Lever

The mine environment is dynamic and operating conditions change continually and are difficult to predict. New equipment, variable geological conditions, modified layouts, and different equipment operators make monitoring and control system difficult to apply without continual software maintenance. The paper reports on algorithms that were developed, encoded with Knowledge Craft Tools, and tested on underground coal mine data to adapt to the dynamic environment. The system receives data from sensors in near real time and then identifies patterns in the data. Using a set of mode features the data is automatically checked to determine the present operating mode. When the operating mode changes from the previous shifts, the system automatically learns the new mode characteristics and uses that mode context for further data analysis. The concepts presented in this paper are applicable to a wide variety of mining scenarios, not just underground coal mining.

Jan 1, 1992

By L. M. Klimov

In recent gears in the coal industry a great deal of attention is attached to the questions of elaborating and introducing the problems of planning and management and, first of all, in the sphere of mine production. The basis for planning of mi- ne production is complexes (sets) of problems for planning the development of mining operations based on different time periods, ensuring the follow-up of changes of mine productive capacities. Complexes of problems for planning, the development of mining operations at existing underground and surface mines within the OASUugol system (Coal Industry-wide Automatic System of Management) are aimed at ma- king decisions close to optimum, i.e. general lay-out of panels, blocks and pillars; transport and ventilation networks; schedules for working out parts of mine take; coordinated mining operations with limited labour and material resources; control of mining operations and ultimately maintaining productive capacities of existing mines at the required level.

Jan 1, 1979

By R. S. Kramer

A bulk compositional chemical analysis often provides incomplete information to help the mineral processor when faced with the problem of removing troublesome contaminants in low concentrations. Michigan Tech has developed a unique approach for addressing this problem. A combination of Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS), and image analysis was successfully used to characterize the species responsible for phosphorus contamination of less than . 05 weight percent in iron ore. An automated routine acquired the chemical signature of each particle on a back scattered electron image. The few particles containing phosphorus were identified from the hundreds of particles examined, and the phosphate phases present were easily characterized.

Jan 1, 1993

By R. D. Hansen, R. R. Klimpel

This paper discusses the influence of frother type and dosage on recovery/selectivity in coal/sulfide mineral flotation as a function of particle size. It is shown that different frother structures exhibit quite different but consistent performance characteristics depending on the underlying particle size ranges involved as well as the dosage levels of both the frother and collector. The data presented on existing commercial frothers and some new special purpose experimental frothers is used to illustrate some general operator guidelines on proper frother selection and use.

Jan 1, 1987

By Joaquin Marti, Peter A. Cundall

This paper reports on some recent work in which several schemes were developed to model jointed rock under high stress, with particular reference to the phenomenon of "block motion" observed during dynamic loading of underground structures. Three approaches were made, corresponding to an increasing relative importance of internal block deformations as compared to rigid block movements. The first one uses distinct element method and assumes internally rigid blocks, which can break, repeatedly, whenever an empirical crack criterion is met. In the second approach each block is allowed three degrees of freedom to deform internally. The third approach, still in the development stage, permits arbitrary deformation of all blocks, which are internally decomposed into finite-difference zones and automatically rezoned during slip to preserve the calculation accuracy on joints. The last two schemes allow arbitrary constitutive relations for the intact rock, and all three schemes permit the geometrical arrangement of joints to be arbitrarily complex, in contrast to normal Lagrange, finite-difference programs, which are unsuited to model discontinua.

Jan 1, 1979

By Arol, A. I., I. Iwasaki

The presence of calcium ion in iron ore pulps causes heterocoagulation of rnontmorillonite on hematite leading to indiscriminate dispersion. Two methods were investigated to control the adverse effect of montmorillonite: a chemical method using such complexing agents as EDTA and sodium tripoly- phosphate, and a mechanical method involving ultra- sonic treatment. Their roles in controlling the adverse effect were investigated by zeta potential measurements, starch adsorption tests, and flocculation and selective flocculation tests.

Jan 1, 1988

By H. D. R. Browner, D. A. Marsh

The need for a product dewatering step between the milling/classification and leach/carbon stages of gold plants has traditionally been performed by thickeners. Whether these be the 'conventional' or 'high-rate' types both require considerable initial capital outlay even without provision for standby facilities. In addition, their sensitivity (both mechanically and metallurgically) to changing feed conditions often results in these being considered 'high-risk' items of equipment, requiring a high degree of attention from operating personnel.

Jan 1, 1992

By Ross W. Smith, Xiapeng Zheng, Merrill P. Allen

The results of flotation of a primary desliming hydrosizer overflow material containing 14.6 wt.% P20, and 3.6 wt.% MgO are presented. The phosphate minerals were collophane and francolite and all minerals appeared to be liberated. The material had not been previously treated with flotation reagents. In the experimentation, various collectors were evaluated for effectiveness. The relative effectiveness of flotation in different flotation devices was determined. Finally a two-stage flotation scheme is proposed using column flotation of dolomite in the first stage and Denver cell flotation in the second.

Jan 1, 2002

By Jack Parker

Pillar design ought to be a matter of matching pillar strength against pillar loading conditions to come up with dimensions that will cause the pillar to behave as required - to stand forever, or for a limited time, or to fail in a controlled manner. But something has gone wrong in recent years, seriously wrong. Pillar design practices have departed from reality. The laboratory and computer have taken the place of the mind. If the mind is put to work and such pillar design practices are examined critically, it becomes obvious that they deal with conditions that do not exist in a real mine. Time, effort and money are wasted, and the end results are incorrect and misleading. These questionable pillar design practices have been passed on from generation to generation over the past 30 or 40 years. The hope here is that we can return to reality as soon as the questionable practices are generally recognized. We could then go back into the mines and define how pillars really work, and mining safety, efficiencies and costs should improve. Let us take a close look at current textbook design practices and compare them to real-life conditions. Common sense might then prevail. (At this time, we will consider only mine pillar design, but similar scrutiny should be applied to design criteria for width of openings, floor conditions and roof support systems.)

Jan 1, 1993

By Michael Li, Kathryn Rogers, Arie Moerman, Mike Cooper

The Brunswick Mine, a Division of Noranda Inc., produces zinc, lead, copper, and bulk lead-zinc concentrates through underground mining of a large massive sulphide deposit. The mining method employed is longhole open stoping with delayed backfilling. In 1996 Brunswick began a review of its mining methods and backfilling operations. In 1997 the decision was made to convert the backfill system from cemented and uncemented rockfill to paste backfill prepared from mill tailings. This paper will describe the features of the backfill preparation and distribution systems, review the handling of technical issues, and discuss experiences since plant commissioning.

Jan 1, 2001

By A. S. Astakhov

Working out of the production calendar plans (schedules) at deep mines which provide for the interaction of all kinds of mining operations determining coal output growth and mining and technical indices is a striking example of mining art. However, multi-variant decision making, a sophisticated system of integration, as well as high labour consumption for calculation and graphic operations in calendar planning require the improvement of traditional techniques and the development of new methods for calendar planning of mining operations at deep mines. The following specific aims were pursued in developing a computerized system of calendar planning (scheduling) of mining operations.

Jan 1, 1979

By S. K. Vidyarthi

Most wastewater clean-up processes suffer from a fundamental lack of specificity in that a Reverse Osmosis process removes all dissolved solids, an Electrodialysis Reversal process removes all ions, wanted or unwanted, etc. Most techniques require the use of a membrane or contact surfaces that are prone to foul-up and are ineffective in situations where solids may be present. A photochemical process for the metallurgical industry on the other hand has the ability to operate specifically on targets that can range from one selected ion to an entire group of homologous species such as all biologically active species. Processes can be designed to change the oxidation states of a target altering the environmental impact. Several processes are currently in operation ranging from Cyanide removal to disposal of radiation wastes. This paper describes applicable photochemical processes with the help of certain key model examples.

Jan 1, 1988