Search Documents

By Abou Saghafi

In order to investigate the design parameters of a future longwall in a thick coal seam a numerical model of gas emission from the goaf area was developed. A Longwall goaf was modelled as a collection of different size coal blocks. For each coal block the partial differential equation of gas flow was independently solved. In developing the flow equations, both pressure-driven and diffusion driven gas flow regimes were considered. The total gas emission rate was calculated by integrating the gas release from each individual coal block over the whole goaf area. The main output of the computer program are gas flowrate from goaf and residual content of caved coal in the goaf as a function of distance from the face. The model was applied to a longwall face driven in a thick seam where large volumes of coal in the roof were to be left behind the face. The gas contained in the coal was mainly CO, with a high desorption rate. Simulations were under- taken to quantify the effect of size of the caved coal on the flowrate from the goaf. The flow properties of coal, such as diffusivity, permeability and coal swelling due to gas adsorption, were directly measured on coal samples from the seam.

Jan 1, 1996

By A. K. Bakshi

In cold regions, rinsing of spent cyanide from leach heaps is stopped during winter and is resumed again after the snow melts. The effect of this idle time on the overall removal process was studied in this experiment. Samples were collected for rinsing tests from one heap at a gold mine near Fairbanks, Alaska. Continuous and interrupted rinsing of this sample were carried out in test columns. The rinse solution was analyzed at regular intervals to determine the rate of cyanide removal from the solids. It was found that total cyanide concentration per rinse cycle for interrupted rinsing test was higher than for the corresponding continuous rinsing test. As a result, interrupted rinsing required less rinsing cycles than continuous rinsing.

Jan 1, 1995

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

By R. J. Snow, S. N. Bhattacharya, D. D. Patil

Electrokinetics involves the movement of charged particles or water molecules in an applied dc field. Applications in particle fluid systems include the dewatering of soils, the densification of mill tailings and the treatment of coal wastes. In this paper, a novel application of this technique is discussed, wherein an electric field is applied to a coal-water slurry flowing through a pipe, resulting in lower pressure losses in the system. A unique experimental setup was designed and built to study the effect of an electric field (dc) on the wall shear stress for the flow of coal-water slurry through the pipe. The effect of solids concentration, current strength and pH on drag reduction across the system was quantified.

Jan 1, 2002

By John Songstead

INTRODUCTION The Bunker Hill mine, located at Kellogg, ID, in the Coeur d'Alene mining district, has been a major pro¬ducer of lead-zinc-silver ore since 1887. Since its dis¬covery, it has produced over 25 401 171 t (28 million st) of ore from 20 to 25 veins and ore zones. The mine now covers an area of approximately 1.609 km (1 mile) in length and 0.8 km (1/2 mile) in width and extends from 1097 m (3600 ft) above sea level to 488 m (1600 ft) below sea level. Production is presently at a rate of 1542 t/d (1700 stpd). During 1965, a new stoping method, the Bunker Hill pillar system, was developed to enable the profitable mining of large, low-grade zinc ore bodies. The system was specifically designed to in¬corporate the Atlas Copco T26GH rubber-tired loaders. High productivities were achieved, and the method was adapted for mining the higher grade stopes where large timber square sets are utilized. This results in nearly 100% extraction. GEOLOGY The area encompassing the Bunker Hill mine lies immediately south of the Osburn fault, a major east-west striking, deep-seated strike slip fault which is the dominant structural feature in the Coeur d'Alene district. The Bunker Hill forms a series of veins and mineralized zones which occur as link structures, tension fractures, and breccia zones in folded, interbedded argillaceous quartzites of the Revett and St. Regis formations of the Precambrian belt series. The Rosco ore body is predominantly a zinc ore body above the Cate fault, which is presently known to occur from the 13 level. [elevation 488 m (1600 ft)] to the 1600 level [elevation 304 m (1000 ft) ]. These ore bodies are stringer zones with at least one dominant 1.8 to 4.5 m (6 to 15 ft) wide band of ore. They dip 0.09 to 0.26 rad (5° to 15°) steeper than the local 0.61 rad (35°) dip of the Cate fault, and also deviate 0.26 to 0.52 rad (15° to 30°) in strike from the Cate. Because of the flat dip and fractured weak hanging wall, normal cut-and-fill mining has not proven practical in this ore body. The mechanized timber methods described in the next section and the Bunker Hill pillar system are the mining methods successfully used. MINING METHODS While pillar stoping and mechanized cut-and-fill stop¬ing methods were obviously superior to the widely used timber stoping methods, as far as cost and productivity

Jan 1, 1982

By R. R. Klimpel

This paper is a summary of the author's industrial experiences on the selection and optimization of flotation reagent schemes for the recovery of gold species. The trends given are a composite of data and experiences gained on 24 different gold ores from around the globe. The primary emphasis is on the benefits of matching the associated gold mineralogy to a reagent scheme most appropriate for that mineralogy. Two general categories are discussed: the flotation of free or native gold species and the flotation of gold associated with a variety of sulfide minerals. Important plant operating factors influencing each of these two categories are presented with supporting examples. Carefully matching reagent chemistry and appropriate operating conditions to any given gold-bearing ore will not only lower the total reagent cost but, more importantly, can lead to measurable increases in gold recovery.

Jan 1, 2000

By H. J. Bogert

Shallow, gently dipping quartz veins at the Mineral Hill Mine are mined in room and pillar stopes. Ore zones are severely folded and fractured, thus actual pillar strength and physical properties of the rock mass deviate significantly from conventional laboratory tests and pillar theory. Laboratory specimens large enough to include pre-existing fractures proved to be representative of actual pillar strength. Further adjustment for specific pillars was based on RQD. Deformation and stress were measured in several pillars during pillar recovery. Stress data and finite element modeling were used to estimate absolute pillar stress at failure. The stress/strain relation provided an excellent indicator of pillar behavior. Good agreement between lab data and underground data was found.

Jan 1, 1995

By Richard D. Harvey

Petrographic properties of carbonate rocks are useful guides to the utilization of these rocks in SO2-scrubbing systems. High porosity and fineness of grain are thought to be the principal properties that contribute to high dissolution rates of the rocks in the scrubbing liquor. Lake marls and chalks are the major types of carbonate rocks that have these properties. Lake marls are composed mainly of equant grains of calcite (mean grain size generally less than 4 microns) weakly agglomerated in- to larger, porous particles. The marls commonly consist of 80 to 90 percent CaCo3 as calcite and aragonite. Impurities are, for the most part, quartz silt and organic matter. The average pore volume for samples of lake marls (1- to 1.2-mm particles) is about 0.50 cc/g, which corresponds to a porosity of about 57 percent. The mean size of pores in these marls is generally between 1 and 2 microns in diameter. Surface areas of lake marls range from 0.8 to 6.8 m2/g. Chalks have grain sizes and shapes similar to those of lake marls, but they generally have smaller amounts of quartz and organic matter and minor amounts of clay minerals. Pore volumes differ from one chalk formation to another; the 1- to 1. 2-mm particles average about 0.20 cc/g, which corresponds to a porosity of about 35 percent. The mean diameter of pores in chalks tested ranges from 0. 15 to 0.76 micron. Surface areas of chalks range from 3. 2 to 20. 1 m2/g. In the United States lake marls are restricted largely to Pleistocene- age sediments that occur in the states around the Great Lakes. Chalk and chalky limestones are restricted mainly to the Upper Cretaceous and Tertiary strata in the Kansas-Nebraska-Colorado area and in the south- eastern states, from Texas to Florida. Results of laboratory tests of the relative dissolution rates of samples at pH 6 and 44°C indicate that, in addition to many lake marls and chalks, oolitic aragonite, pelecypod shells, and carbonate waste sludges from certain industrial plants also have high dissolution rates.

Jan 1, 1974

By V. J. Matta, A. A. Pincheira, I. A. Reghezza, Ch. J. Vergara

The growth of solvent extraction in Chile has been astonishing during the last years and has been established as a very successful technology. However, there are still limitations that must be improved, mainly, the problem of carry over from one phase to the other and the losses of organic reagent associated with the crud formation. These are problems that our company has been taking care, solving them with high efficiency and low costs, allowing important increases in the copper output of our plants and capital savings by means of the optimization of the use of nonproductive units in the SX plants.

Jan 1, 1998

By E. De Souza, J. F. Archibald

"Many underground mines use cemented backfill to mitigate environmental effects associated with tailings disposal. The large energy needs associated with mine backfilling and cement production operations create significant CO2 and Greenhouse Gas Emissions. This paper introduces post-consumer glass as an alternate, equally effective and lower cost binder agent strategy for cement in backfill that may be implemented to assist in reducing solid waste production, lowering energy costs, and restricting Greenhouse Gas Emissions. Extensive engineering testing, consisting of pipe flow loop tests and strength tests, has been implemented in order to demonstrate the technical feasibility of process integration within industry. An economic analysis has demonstrated that glass is competitive in cost relative to cement and a socioeconomic study has further indicated that the utilization of glass in mine backfill would create a new market for waste glass that requires less processing and reduces costs."

Jan 1, 2005

By N. Parra, M. N. Herrera, T. Vargas, C. González, B. Escobar

The bioleaching of mineral sulfide pulps in a bench-scale rotating-drum reactor was studied. The reactor contained horizontal paddles on the inner wall for lifting the mineral pulp. The performance of the reactor was tested by bioleaching a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans (ATCC 19859). The concentrate was efficiently bioleached at a 50% pulp density with the drum operating at from 0.5 to 1.0 rpm. Attempts at bioleaching the concentrate at the same pulp density used in a conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows the process to operate at much higher pulp densities than conventional stirred-tank reactors. This results in improved bacterial activity because of better attrition control of the mineral particles.

Jan 1, 1999

By Jerry Wang, Greg Bold, Mahmood Khwaja, Rebecca Caldon, William Simcoe

Phase III and Phase IV of the Beaver Creek Clean River Project, Albany, NY, includes microtunnel construction of 2,320 feet of 48-inch/36-inch internal diameter (ID) conveyance pipe and a 525 foot long 9.5-ft horseshoe shape roadheader excavated tunnel. Notable challenges were encountered during the construction including mixed face tunnel conditions, undocumented existing fill ground conditions that resulted in settlement during shaft construction, and unstable tunnel face conditions. This paper discusses several of the key challenges encountered during construction and selected solutions to construction sequencing and methodology to successfully complete Phase III and Phase IV of the Beaver Creek Clean River Project.

Dec 1, 2022

By Regina N. Tempel, Laurie S. Balistrieri, Lisa L. Stillings, Lisa A. Shevenell, Maggy F. Lengke

Dexter pit lake, within the townsite of Tuscarora, Nevada, has been in existence since 1990 and provides a natural laboratory for the study of cycles of trace elements associated with ore deposits (e.g. As, Cu, Pb, and Se). Our goal in this study is to develop and calibrate methods of geochemical modeling that may be applied to estimating the concentrations and fluxes of trace elements in pit lake systems. Our initial modeling work considers limnology, hydrology, wall rock mineralogy and geochemistry, benthic fluxes, and colloid composition. Results from our work may be useful in evaluating water quality in the arid West.

Jan 1, 2000

By Wen L. Cai

This paper examines the effects of different block dimensions and cone bases on the economic open pit limit design based on case studies on a coal deposit consisted of two west- east elongated, near vertical thin seams starting with a base model dimension of 200x170x50 (NX*NY*NZ) with a block dimension of 10mx5mx4m (DX*DY*DZ), the blocks were combined along easting, northing and elevation directions. Two cone bases were used, one with a base radius of 10 meters, the other with a base radius of 0. Two pit design algorithms, one is the floating cone algorithm, the other is an optimum algorithm, were used to see which one of the two pit design algorithms is more sensitive to block dimension and cone base variations. The results are presented and analyzed.

Jan 1, 1992

Gold heap leach operations often process low grade ores with little margin for cost increases. The advantage of heap leach operations is the considerable savings in both capital and operating costs. This paper looks at an alternative pH modifier to lime in the heap leach process, namely bauxite waste mud or red mud. The red mud can contain trace amounts of gold and was found to be an excellent source of slow release sodium hydroxide for long-term pH modification. Column cyanide leaches showed that 25 kgt-1 of red mud provided a higher pH and longer pH modification than 0.25 kgt-1 of lime. Contaminants leached from the red mud hampered the adsorption of the aurocyanide complex onto activated carbon.

Jan 1, 1993

By Roland Heersink, Charles H. Wells

This paper discusses how a mill uses off-site data hosting approach to effectively utilize an entire suite of advanced applications to optimize daily operations, without incurring the overhead of on-site systems, staff and support. Details of the solution are provided, together with a live view of actual plant operations. Security and authentication mechanisms are also outlined so that users may gain an appreciation of the actual security of the remotely hosted data. A number of Web-hosted software applications provide direct connectivity to the database offering rapid and deterministic response times to clients. A 24x7 help-desk is available to authorized users from any Internet connected device. The paper shows how mill management advantageously use wireless PDA's to view what is going on at anytime and from anywhere. It concludes with a summary of how the approach is being used to speed decision-making and capture spot market opportunities.

Jan 1, 2002

By D. N. Thompson, R. L. Sayer, K. S. Noah

Economical remediation of acid rock drainage (ARD) at secluded high-altitude western ore mines is difficult given the current treatment technology. Several passive-engineered systems that are based on wetland technology were tested in the laboratory with three western ore mine ARDs (Co, Cu and Fe mines) and with a copper leachate effluent. These systems used well-weathered lodgepole pine sawdust as the sole carbon source and mud from a pond at one of the mine sites as the source of sulfate-reducing bacteria (SRB). Simple one-pass flow-through systems removed 44% to 99% of the vari¬ous heavy metals front the Co and Cu mine ARDs and increased the pH from 3 to 7 after 28 days of SRB acclimation with a five-day residence time. Carbohydrate utilization rates were generally low, except for one 437-day run, which consumed 25%, 30% and 21 % of the cellulose, hemicellulose and lignin, respectively. Initial pH, amounts of toxic heavy metals and the degree of predegradation of the sawdust were found to significantly affect both remediation potential and acclimation time. Engineered SRB systems, alone or in combination with other passive technologies, offer promise for the economical remediation of western US ore mine ARDs.

Jan 1, 2000

By Harry M. Castrantas, James L. Manganaro, Craig W. Rautiola, James Carmichael

Caro's acid (peroxymonosulfuric acid) was successfully field tested as a cyanide detoxification agent at a North American gold mine. An on-site FMC generator injected Caro's acid into a mill tailings slurry sump. The WAD cN-(weakly acid dissociable plus free cN-) was reduced from 40-108 ppm to below the target level of 20 ppm using a 1/1 mole ratio of CA (Caro's acid) /CN-. At an inlet CA/CN-mole ratio of 1.8/1, WAD CN­concentrations as low as 4 ppm cN-were achieved. Raw material costs for the cyanide detoxification were cut by 60% compared to using hydrogen peroxide (H202) alone. Detoxification time with Caro's acid was much faster compared to H202. This resulted in completion of detoxification before the treated slurry reached the tailings pond thereby substantially reducing the probability of wildlife fatalities.

Jan 1, 1993

By A. K. Ghose

The increasing application of roadheading machines in the coal industry has prompted the development of an appropriate selection methodology for such machine applications in specific locales. Accurate geological sections and comprehensive rock testing are required for all machine tunneling. Using suitable geotechnical parameters and index tests, sensitive both to excavability and standability of the strata, a classification scheme has evolved to help evaluate the rock mass vis-a-vis application of a given weight-class of roadheading machine. The classification parameters include point load index, brittleness, abrasiveness, average crack density, and ground water, which with assigned numerical ratings, lead to a quantitative global rating of the rock mass. For each rock mass class, the selection of an appropriate roadheading machine is recommended. The paper illustrates the application of the rock mass rating system and also describes simple index tests for evaluating the classification parameters for brittleness and abrasiveness. Manuscript not received in time for publication.

Jan 1, 1983

By T. L. Heidrick

Late Cretaceous-early Tertiary Cordilleran porphyry Cu-Mo districts and their consanguineous Zn-Pb-Ag-Au-W vein and replacement deposits of the Rocky Mountain region comprise one of the largest, best studied, diverse, complex, puzzling, and richest compound metallogenic provinces on earth. A concise space-time definition of intermineral plate, regional and local structure-tectonic frameworks is crucial to deciphering their diachronous metallogeny and enhancing the explorationist's odds of future discovery.

Jan 1, 2013