Search Documents

By J. Kretschmann

"By the end of the 1950s, the German hard coal mining industry produced 150 million tons of hard coal per year in 170 collieries with 600,000 employees. At that time, 70% of the primary energy demand of the Federal Republic of Germany was covered by domestic coal. However, due to coal mining becoming an increasingly globalized business and the oil and gas industry producing with lower costs, the German domestic hard coal industry stood constantly under restructur-ing pressure. The industry declined until the end of its life cycle. In 2007, a political understanding was arranged to phase out German hard coal mining in a socially acceptable manner by the end of 2018. This decision required a new strategy for the coal mining industry. Being strictly finalized, the German hard coal mining industry has to be prepared for the post-mining era. To create a sustainable development strategy, the long-term impacts of coal mining activities in Germany concerning the environmental, economic and social dimensions will be analyzed systematically and forward-looking. The regional and social responsibility during the closing process and for the post-mining era will be emphasized. High technical standards in environmental protec-tion and post-mining technologies, as well as long term experiences in the development of former mine sites to create new jobs are significant from an international point of view. The traditionally constructive social partnership between employers, union, and employees has enabled long-term stable adaption processes and avoided social friction. The sustainability strategy of the German hard coal mining industry can be regarded as a role model for other mining countries and regions facing similar transition challenges. INTRODUCTION Principally, mining is a finite business that reaches its end if the deposits are depleted or the raw materials can no longer be mined in an economically profitable way. However, the impact of mining is po-tentially an infinite one – at least if you measure it at a human time scale. Mining always means interfering with geological and ecological structures that cannot be reversed to their original condition. In general, the mining cycle (Figure 1) can be divided into three phases: 1. The exploration phase, in which the deposit is investigated to determine its technical and economic profitability. The period of these undertakings is relatively short and can lead to the launch of mining operations. 2. What follows is the actual mining phase which usually lasts for a long time and ends latest when all deposits are fully depleted. This lifespan may be shortened if the economic conditions (production cost or market price) deteriorate. Nevertheless, mining may be resumed if those conditions become favorable once more (examples are silver mining in Germany or rare earths mining in the USA). 3. The longest phase, however, is the post-mining phase as the human interference into geology and nature is usually inten-sive and irreversible. Mining can lead to consequences which have a permanently adverse impact on people and the environment; therefore, they have to be managed as best we can (1)."

Jan 1, 2017

By Max Friedemann, Franziska Günther, Helmut Mischo

Ensuring adequate ventilation is a critical aspect of safety in underground mining operations. In small-scale mines in particular, key ventilation parameters such as temperature, humidity, and air velocity are often measured manually and only at infrequent intervals, typically using analog instruments. As a result, real-time monitoring of environmental changes, timely detection of hazardous situations, and demand-driven ventilation control are not feasible. This presentation discusses the selection and evaluation of modern digital ventilation measurement devices, including handheld instruments with digital data logging capabilities and continuously operating sensors with potential for real-time data transmission. The investigations focus on the challenges posed by underground environments with extremely high humidity levels, which can adversely affect sensor performance and electronic components. The results are based on testing conducted at the Research and Teaching Mine of TU Bergakademie Freiberg—an underground ore mine characterized by humidity levels exceeding 95%. Findings include assessments of measurement accuracy, reliability, and practical applicability under these demanding conditions.

Feb 22, 2026

By Peter L. Comanor

At Getchell, Nevada a thousand tons per day mill for extracting gold from an ore containing orpiment and realgar was operated several years until early 1967. A cyanide process with a roaster was used in the processing of the ore. Mill wastes were contained in tailings ponds, in which the concentration of arsenic, currently, is one per cent or higher, Studies were conducted determining the effect of the tailing wastes on the Upper Sonoran vegetation of the area. Grid and line-intercept techniques were employed to obtain botanical informatics of the area surrounding the tailings ponds. Data of the per cent ground cover, species frequency, and plant vitality as a function of distance from the tailings ponds was collected. The data was compared to other botanical data collected from a control site outside the influence of the tailings ponds. In an attempt to isolate naturally occurring factors for varying plant communities from hose induced by factors derived from the close proximity of the tailings, soil cores were taken along the line-intercepts at intervals of 30 meters. The cores were analyzed for several compounds and elements needed for growth, or known to inhibit growth. Specific physical parameters of the soil samples were also taken. The paper describes the impact made by mill wastes containing large amounts of arsenic on the Upper Sonoran vegetation of the Getchell region. Described in detail are the techniques used to make the correlations between the plant communities and the influences of mill wastes.

Jan 1, 1974

By H. J. H. Pieterse

This paper highlights the mineralogy of the Barrick Goldstrike Mines Inc. area. The mine is located at the north end of the Tuscarora Spur and is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend. The Betze, Post, and Meikle Mine are major deposits located in the area. The deportment of gold, its leachability, and various process options are also evaluated. Particular emphasis is given to the practical and economic considerations of ore control, and routing of ore to a process option.

Jan 1, 1993

By F. C. Appleyard

As one of the more important Industrials Minerals, gypsum occupies a significant place in the economy of the United States, particularly in that segment which can be loosely called the Construction Industry. For many years, products made from gypsum have been a major building material, and the usefulness and versatility of these products is such that their widespread use is expected to continue. In 1968, according to U.S. Bureau of Mines statistics, the value of all gypsum products sold in the United States was 405,000,000 - and although this value has dipped from the 1964 high of $ 432,000,000, it is expected to trend upward in the next few years to equal and surpass this figure as the construction industry recovers from its current squeeze of "tight money" and high interest rates. There are many factors to be measured in determining the potential value of any mineral deposit, and how it might fit within its particular industry. What, then, are the qualities which a gypsum deposit must have in order to profitably participate in the four hundred million dollar plus business which is the gypsum industry? First let's consider the geology of gypsum, the geographic distribution of deposits, and the more important factors such as size, grade, capital requirements, and operating cost. Then, an understanding of the uses of gypsum, various types of products, and location of markets would be helpful, along with such other factors as the structure of the industry, price trends, etc.

Jan 1, 1970

By Karl J. Benecke

Though the first patent on a bucket wheel excavator was granted in 1881 in the U.S. this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with the development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generating, despite the low heating value of German lignite in the order of 8500 kJ/kg (3600 BTU/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is in the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output open pit mines. The largest one, Fortuna Mine in the Cologne district, produced a, total of 45 000 000 t lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95 200 000 bank m3 equal to 200 000 000 t overburden had to be removed to accomplish this lignite output. The largest BWE (Fig. 1) ever built is working in the Fortuna Mine, too. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 t, its wheel diameter 21.6 m, as high as a 7-storey building.

Jan 1, 1977

By W. J. Schlitt, K. McNaughton

A heap-leach field test was conducted during the 1993-1994 winter season at Carmacks, Yukon Territory, Canada. The purpose of the test was to demonstrate the viability of heap leaching Carmacks oxide copper ore in an arctic setting on a year-round basis. The test itself utilized a 5-m-diam crib loaded with 250 t of composite ore from the Carmacks copper deposit. The ore was stacked to a total height of 7 m in the crib, including 1 m of ore as an over- layer above the emitter system. This matched the plan for the commercial heap at the time when the test was started. The design also replicated an interior segment of the commercial heap. Leaching was done at a flow rate of 0.2 L/min/m2 using leachate at 21 °C. This temperature was maintained with no external heat input other than normal process heat transferred from electrowinning to the leachate via solvent extraction. Winter conditions were quite typical of those expected at the mine site. The temperature reached -54°C, while averaging -13°C over a three-month period. In spite of some flow system problems, leaching continued unabated, and freezing was limited to the insulating ore over-layer and isolated points near the outer crib walls. Thus, the test demonstrated that year-round heap leaching of Carmacks copper ore is practical in an arctic setting.

Jan 1, 2000

By L. Sandbak

The TRJV Mine is located approximately 43 miles northeast of Winnemucca, along the east flank of the Osgood Mountains in the Potosi Mining District, Humboldt County, Northwest Nevada (see Figure 1). The Turquoise Ridge Mine is an underground mine, and is a 25% joint venture partner with Newmont Mining. The TRJV mine utilizes the underhand cut-and-fill mining method due to the relatively low rock quality in the ore zones and the relatively shallow dipping 25-45 degree ore body geometries. This paper defines a rehabilitation risk rating system (RRRS) for prioritizing rehabilitation of drifts damaged in the mining processes including long term development drifts providing access to the mining areas. The ultimate use is as a mine planning tool for the organized scheduling of rehab in a timely manner. A few case studies of the most needy rehab areas identified by the RRRS mapping system is presented, and the type of rehab completed design for these areas. Suggestions on improving the rehab risk mapping system include the use of support history and rock mass strength rating factors.

Feb 23, 2014

By B. Derin

In this study, the Reddy-Blander model was applied to predict the sulfide capacity (CS) values of FeOx-CaO-SiO2, FeOx-MnOx-SiO2 and FeO-MgO-SiO2 ternary slags, which were experimentally studied in the literature within the temperatures between 1,673 and 1,923 K. As expected, sulfide capacity values of the slags increased with increasing temperature and decreased with increasing acidic content. The model was found to be in agree-ment for all slag systems at the temperature range of 1,773-1,923 K. However, a disagreement occurred when the basic content was relatively high, at 1,673 K for FeOx-CaO-SiO2 and FeO-MnOx-SiO2 slags. The effect on the CS of high amounts of Fe+3 and Mn+3 in the slags is discussed.

Jan 1, 2011

The United States is being invaded... by foreign capital: marks, francs, pounds, yen, lire, riyals, you name it: On almost any given day the Wall Street Journal will contain a new report on a department store, newspaper, bank, hotel, agricultural land, supermarket chain, et a1 being bought into by overseas investment. Xenophobic reaction to this revised national condition has begun to set in. Several farming states have and are introducing legislation to monitor foreign land buying. In Congress a mandatory reporting requirement for foreign purchasing is currently under study. In a relatively short period the country has reverted from world leader- ship in overseas acquisition and involvement to become itself one of the prime investment opportunities in existence. Interestingly enough, one of the industries where this changed status has become most apparent and pronounced is within that small/regional/segmented/low value-to-weight bulk commodity enterprise ranked as the backbone of the nation's construction activity. U.S. cement making is not only undergoing internationalization in its ownership, but also in its product, equipment, and engineering expertise.

Jan 1, 1979

By Michael J. Beus, Jan G. Patricio

INTRODUCTION The U.S. Bureau of Mines, Spokane Mining Research Center, has been conducting and documenting rock mechanics research in the Coeur d’Alene mining district for the past ten years (1, 2, 3, 4, 14, 15). A current project combines the information gathered from rock mechanics instrumentation, geologic structure, and analytic techniques to improve shaft and support design for the deep mines of the district (3). This project required knowledge of the anticipated loads and the physical properties of the rock mass to provide accurate input data for computer design models. Several techniques have been utilized to determine the physical parameters including the USGS (U.S. Geological Survey) solid inclusion probe, the CSIR (Council for Scientific and Industrial Research) biaxial and triaxial strain cells, and the CSM (Colorado School of Mines) dilatometer. This paper describes the determination of the in situ modulus of deformation in three mines over a period of three years and the evaluation of these results as they applied to this project. The need for in-situ rock mass properties such as the modulus of deformation has stimulated research and development of a large number of instrumentation techniques. One area of continuing interest involves various methods of radial borehole dilation. This concept was pursued by Menard (9) with an apparatus known as the pressure meter, which is used frequently in soil mechanics. Other developments in rock mechanics include the CPC (cylindrical pressure cell) by Panek (11) and the dilatometer by Rocha et.al. (13) in Portugal. The CSM dilatometer, which also utilizes this technique, was chosen for this project because it required a small amount of background study, was inexpensive, and could easily be combined with other experiments being planned for the test locations. Although no previous field applications to hard rock (compressive strengths greater than 20,000 psi) has been documented, the instrument was selected since good results have been achieved in granite, oil shale, and several coal measure rocks (11, 12).

Jan 1, 1977

By Adam Bedell, Brad Crenshaw

Tunnel project contract documents often present groundwater infiltration requirements for components of the underground portions of the project. All too often these documents require quantifiable target inflows for these components, but only refer to them in subjective terms such as “dry,” “manageable,” etc. The Contractor’s definition of these terms will inevitably differ from the Engineer’s definition of these terms. The purpose of this paper is to look at common subjective terms used in documents and provide suggestions for reasonable quantifiable language. Additionally, the paper will provide information and recommendations on relative levels of cost and effort increase needed to provide increasing levels of water cutoff (i.e., achieve “dryness”?).

Dec 1, 2022

By Jon A. Hummer, Aleksandar D. Bugarski, Shawn Vanderslice, Teresa Barone

A study was conducted to examine the potential of diesel emissions control strategies based on retrofitting existing power packages with exhaust aftertreatment devices and repowering with advanced power packages. The retrofit systems, a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF), were evaluated individually using a US EPA tier 2 (ter 2) engine operated under four steady-state conditions and one transient cycle. The DOC effectively curtailed emissions of CO, and to some extent organic carbon (OC), elemental carbon (EC), and aerosol number concentration. The DPF system offered substantially higher reductions in OC and EC mass and aerosol number concentrations. Both, the DOC and DPF achieved reductions in the aforementioned emissions without adversely affecting emissions of NO2 and nano-sized aerosols. The strategy of repowering with an advanced system was examined using a US EPA tier 4 final (tier 4f) engine equipped with a cooled exhaust gas recirculation system and diesel exhaust fluid-based selective catalytic reduction system, but not with a DPF system. The tier 4f engine contributed substantially less than the tier 2 engine to the EC and OC mass, aerosol number, and CO, NO, and NO2 concentrations. The tier 4f engine was very effective in reducing aerosol mass, NO, and NO2 concentrations, but it was not equally effective in reducing aerosol number concentrations. The implementation of viable exhaust after treatment systems and advanced diesel power packages could be instrumental to the underground mining industry to secure a clean, economical, and dependable source of power for mobile equipment.

By E. W. Greig

This paper is an account of exploration for bauxite in the Amazon Basin, Brazil, and particularly of the discovery, exploration and development by Alcan of the Trombetas deposit so a general account of the Trombetas Project has already been published in E/MJ (Anon. 1975) to which the reader is referred for details on owner-ship, infrastructure and construction as well as the proposal for mining and treating the bauxite. It is impossible to consider the Trombetas deposits in isolation. A regional account of bauxite in and around the Guyana Shield and the northern portion of the Brazilian Shield is included and it is suggested that these deposits all formed during Tertiary time under similar conditions.

Jan 1, 1977

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By Charles T. Steuart

The Arkansas Novaculite of Devonian and Mississippian age is the most distinctive formation in the central Ouachita Mountains of Arkansas from the standpoint of both topography and lithology. The formation typically forms precipitous, narrow ridges (hogbacks) which reflect the steepness of dip and the resistance and thickness of the rock units. The Arkansas Novaculite varies from less than 200 feet thick in the north to locally over 800 feet thick in the south and outcrops over an east-west distance of 360 km (200 miles) in the Ouachita Mountains of Arkansas and Oklahoma. Most of the rocks of the formation are highly siliceous with novaculite predominating, and lesser quantities of chert, siliceous shale, conglomerate and rarely sandstone. Novaculite is commonly defined as a homogeneous mostly white rock, translucent on thin edges with a dull to waxy luster and composed almost entirely of microcrystalline quartz. The word novaculite comes from the Latin word novacula, meaning razor hone. This term was first used by Richard Kirwan in his mineralogy text of 1784. The origin of novaculite remains controversial but we believe it was a primary silica derived mostly from the alteration of submarine volcanic-rich materials, with numerous fine biogenic components and some minor clastics (derived mostly from foreland facies via turbidity currents) and deposited as an amorphous siliceous ooze in the deep Ouachita trough. It was subsequently converted to microcrystalline quartz during diagenesis by the compaction of the overlying rocks and the intense Late Paleozoic Ouachita Mountain tectonism. In the central and southern portions of the region three divisions of the formation have been defined: a Lower Division predominantly of light-colored novaculite; a Middle Division of interbedded dark chert and shale; and an Upper Division of massive often calcareous novaculite. In the northern exposures the formation is thinner and contains more black chert and shale, chert-shale conglom¬erate, sandstone and less novaculite. The massive novaculite of the Upper and Lower Divisions is a source of high purity silica (99+%). Indians were the first to use novaculite. They made their various tools and hunting implements from the weathered broken rock until they learned the quarrying techniques. The first white men in the area recognized the use of novaculite for sharpening their tools and knives: previously whetstones were obtained in small quantities from Europe. To this day whetstone is quarried mostly in areas which the Indians and possibly the Spanish previously worked. Some of the current mining practices have changed very little from those of the early quarryman. In areas where the novaculite of the Upper Division is poorly cemented, this friable tripolitic material has found applications in such uses as an abrasive, as a filler or extender in paints, plastics and other purposes. Some of the dense novaculite is suitable as a filler in fire bricks and also in plastics. Because some of it has the tendency to decrepitate when heated not all novaculite can be used for these applications. Several quarry operators are crushing novaculite for road, concrete, and other aggregate. This use was formerly rather limited due to the abrasiveness of the novaculite on crushing and screening equipment. Further potential uses of novaculite are speculative but include application of high purity silica in the production of silicon metal for solar cells, seed or "growing", and fusing quartz for electronics.

Jan 1, 1985

By Keat Chuan Chew, Qiao Yue Tung, Teoh Yaw Poh

"1 INTRODUCTION With a land area of 718 square kilometres housing a population of slightly over 5.4 million, as of 2014 (Department of Statistics Singapore 2015), Singapore is a highly urbanised city. Transport infrastructure is critical to keep the country and economy highly connected and functional as the population in Singapore continues to grow. The importance of a robust transport infrastructure is recognised by the Ministry of Transport in Singapore, which is working towards bringing 8 in 10 households within a 10-minute walk of a train station by 2030 (Ministry of Transport 2015). This gives rise to the rapid expansion of the rail network in highly urbanised Singapore, resulting in more tunnelling work having to be carried out in closer proximity to existing buildings. Such tunnelling work is expectedly more challenging and complex, and if not managed effectively, will impose higher risk to the adjacent buildings. Hence, the Building and Construction Authority (BCA) has implemented specific control measures to mitigate such tunnelling risks and to ensure safety of the public. 2 CHALLENGES FACED BY TUNNELLING WORK IN SINGAPORE 2.1 General Challenges of Tunnelling in Singapore With the increasing densification of the rail network in a highly urbanised setting, rail projects in Singapore are faced with several key challenges. One such construction challenge is constrained construction sites brought about by network intensification. Alongside the growth of the rail network, shown in Figure 1, other infrastructure networks in Singapore are also continuously growing. Underground interchange stations between networks become increasingly common, forcing each underground interchange station to be constructed deeper and in closer proximity to existing buildings (Figure 2). Singapore is not alone in facing this issue. The same can be observed in cities like London, in which its myriad network of subway lines pushes new lines and interchange stations to be constructed deeper."

Jan 1, 2016

By Deniz Akbay

The strength of rocks and soil is a crucial design parameter in engineering projects, and it can be determined through various test methods such as uniaxial compressive strength, tensile strength, and shear strength. The point load index test is a popular indirect test method for predicting the uniaxial compressive strength of rocks. However, the reliability of the point load index’s estimation of uniaxial compressive strength of rocks is questioned due to the wide range of coefficients that are used to predict uniaxial compressive strength of rocks using point load index values. Factors such as the shape and type of rock specimen, practitioner, and test apparatus used can affect the accuracy of the point load index test. This study investigated the effect of four different specimen shapes used in point load index test (diametral, axial, block, and irregular lump tests) in predicting the uniaxial compressive strength. The rock samples were tested using four test procedures which are called diametral, axial, block, and irregular lump tests. The results showed that the irregular lump test was the most accurate in predicting uniaxial compressive strength, with the highest correlation coefficients and lowest mean absolute percentage errors. The point load index test can be used as a reliable predictor of uniaxial compressive strength of rocks when the irregular lump test is preferred.

Oct 18, 2023

By R. A. Pimentel

Many longwall operators experience difficulty complying with the federal regulation limiting average dust exposure. Others are currently in compliance, but the dust exposure limit keeps then from increasing their production. Spray water is a major means of dust control. Excess water can cause problems in the transportation system and the cleaning plant, and reduces the Btu value of the run of mine coal. Thus, the dust exposure reduction per unit of water sprayed must be maximized. This paper discusses underground tests recently completed as part of a Bureau of Mines research program to determine the effects of variations in spray water flow rate, pressure, proportioning and spray orientation on longwall shearers.

Jan 1, 1984

By Jake Beale, Joe Wickline, M. Van Dyke, Ted M. Klemetti

A longwall coal mine in southwestern Virginia mining the Pocahontas #3 Coal Seam experienced a history of mining-related seismic events. The events were never large enough to cause concern until three major events occurred recording 3.4, 4.3, and 3.4 ML in 2005, 2006, and 2007 respectively. Two of the seismic events generated an air blast which damaged stoppings which fueled a mine fire in 2005 and 2007. The mine responded to the events by narrowing the longwall widths, changing ventilation controls, installing a 7-sensor seismic system around the active panel, and creating a mining hazard map to avoid similar geology in the future. All of the actions taken have prevented seismic activity from impacting mining operations, but it did not prevent other large seismic events from occurring (Van Dyke et al., 2018). In 2016, another large seismic event, measured at 3.7 ML, occurred in the gob that was reported by the local media and recorded by the United States Geological Survey (USGS). While the event did not directly impact mining operations, mine management wanted to know where and under what conditions could large seismic events occur in the future. The National Institute for Occupational Safety and Health (NIOSH) became involved to help understand what conditions precipitated these events so that future mine design could more accurately assess seismic hazards and reduce the risk to mine worker safety. Researchers at NIOSH and mine management created a seismic forecasting map that combined three factors: (1) overburden thickness, (2) sandstone thickness, and (3) the expected caving height of the gob. The criteria were developed based on the geologic data the mine collected from core drilling, e-log analysis, and fiberscope observations. The forecast map was able to provide an accuracy of 72%–85% of events 1.5 ML or greater and 100% accuracy of events that were 3.0 ML or greater based on historical data. The seismic forecasting map was applied to the entire future mining area to show areas where seismic potential could be the greatest based on current mine design planning, ultimately improving the ability of the mine operator to assess the seismic hazards surrounding active and future mining areas (Van Dyke et al. 2018). Following this research, the seismic forecasting map was implemented into the mine’s hazard recognition program and is continuously updated and evaluated prior to mining each longwall panel. This paper will cover in more detail how the seismic and lithologic data was processed and how the mine implemented a new seismic mitigation program based on the forecasting results.

Apr 26, 2022