Search Documents

By J. B. Yianatos, G. S. Dobby, J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

The question is posed as to why columns typically have a collection zone 10 m high (H) by 1 m in diameter (D). Three geometry dependent factors are considered: degree of mixing, Np; volumetric bias rate, B; and volumetric gas rate, G. Increasing H:D decreased Np and B, which improves performance but decreases G, which causes the column to approach overloading. Taking typical column operating conditions, it is concluded that a collection zone H:D of 10:l is a reasonable compromise.

Jan 1, 1987

By Judith A. Marks, Deane K. Smith, Jan M. Mutmansky, Maria Klimkiewicz

The mechanical mining of coal seams where roof, partings, and floor rock are extracted along with the coal often introduces large numbers of quartz particles into the mine atmosphere. This study concentrates on the quartz properties in situ and in the airborne dust to determine how they are released from the source rock and whether they are fractured by the mining machinery. Three mines using drum-type continuous miners from different geographic areas were sampled to provide a data base. The roof and floor rocks were primarily siltstones containing 5% to 25% quartz measured by the X-ray powder diffraction (XRPD) method. Much of the work presented here is based on the morphologies of the mineral grains determined by the scanning electron microscope (SEM). The study concentrated on particles of 0.2 to 10.0 µm and on particles containing > 75% Si. Mechanically-crushed quartz particles were also examined for comparison purposes. Particle shapes from the airborne samples suggested that fractured quartz particles were rare. Particle statistics also show that the average size of quartz particles in the airborne samples were similar to the average size of all particles. The conclusion is that very few quartz particles from the source rocks are fractured during mining due to their small initial size and the protection of the associated clays.

Jan 1, 1991

By Robert Stefanko

The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given elsewhere (1,2). The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania.

Jan 1, 1969

By T. Ertekin, R. V. Ramani, W. Sung

The emission of methane in the coal mine working faces has two immediate impacts with regard to coal mine planning. Firstly, at the planning stage, the coal mine ventilation system must be designed such that airflows in the faces keep the concentrations of the gas in faces areas to below one percent. If the concentrations were greater than one percent, the production machine has to be shut down resulting in a loss of productive time. In an extreme case, concentration can reach explosibility limits which may lead to ignitions and explosions. Secondly, in excessively gassy coal seams, several alternatives can be applied to the mine layout configuration, and the mining method to be predicted for the extraction of coal, so as to insure a productive and safe operation. In this study a two-phase, two-dimensional finite-difference model was used to predict the methane emission rates into active mine working area under several methane drainage schemes. The numerical model utilizes a recently developed multi-mechanistic flow theory which describes the flow of methane in an heterogeneous and anisotropic coal seam. Transport of methane in the micropore structure of the coal is described by the Fick's law of dif- fusion under the influence of existing concentration gradient, while flow in the more permeable butt and face cleats (macropore spaces) is formulated by Dar- cy's law under the influence of existing pressure gradient. The desorption of the methane is accounted with the aid of a quasi-steady kinetic sorption model. A series of simulation studies were conducted in a systematic manner by sifting through the parameters associated with the coal seam characteristics and the degasification strategies in order to understand those which most significantly affect the methane emission rates in the face areas during mining. Along these lines, the effects of coal seam properties such as thickness, porosity, permeability, sorption characteristics and scheduling of drainage process against the mining operation have been isolated to understand the role of each individual parameter on the methane emission rates.

Jan 1, 1987

By Linda Frederick

In July 1997, Krupp Canada obtained the contract to design and supply the conveyor system for Chile's Los Pelambres copper mine expansion project. Progress on the overland conveyor system is currently on schedule. It is a challenging task to convey copper ore from an open-pit mine located on a mountain site 3,000 m (9,840 ft) above sea level down 1,300 m (4,265 ft) to the processing plant at the valley floor below. The Los Pelambres conveyor system moves copper ore at a rate of 8.7 ktlh (9,600 stph) and at a speed of 6 ml sec (1,180 ftlmin) for 12,750 m (41,830 ft). The distance is divided in three conveyors, each 1,800 mm (71 in.) wide. The largest conveyor is 6 km (3.7 miles) long. To protect against avalanches and rockslides, the conveyors run through a 12-km- (7.4-mile-) long tunnel system. The lowest of the three conveyors is equipped with a shuttling head end. With this, the conveyor discharge point can be moved back and forth by 100 m (330 ft), allowing it to build up a longitudinal stockpile at its end. To meet the extreme design parameters, the limits of conveyor design had to be pushed to record-setting marks. For instance, the ST-7800 steel cord conveyor belt is the strongest belt ever installed in a conveyor system. A total drive power of 25 MW (33,535 hp), consisting of 10 2.5-MW (3,352-hp) drives, is included in the design plans. In loaded condition, the electric motors act as generators and feed electric energy back into the power grid. The motors are controlled by variable frequency inverters that provide an infinite adjustment of motor speed. This technology allows starting and stop- ping the conveyors precisely along predetermined acceleration and deceleration ramps. This is done so harmful belt jerking and stress waves can be avoided.

Jan 1, 1999

By M. Dayne Aldridge

A description is given of an experimental ventilation control system designed, built, and tested by WVU under United States Bureau of Mines sponsorship. A description is given of the control, system used and the mine-wide microcomputer-based ventilation monitoring system used with it. Test results of experiments conducted with this system at Eastern Associated Coal Corporation's Federal No. 2 underground coal mine are presented. In addition, a brief description is given of a new microprocessor based system presently being tested.

Jan 1, 1980

By R. B. Hawkins

The discovery of the gold deposits of the Jerritt Canyon district and the construction of the E. R. Bell Mine is one of the significant mining developments in the United States during the past ten years. This mine will exploit one of the larger deposits of disseminated gold presently known, with proven, recoverable reserves in excess of 67.6 million grams of gold. Interest generated by the success of this project has contributed greatly to the tremendous resurgence in exploration for disseminated gold deposits in Nevada and throughout the west. The Jerritt Canyon project, including the Bell Mine, is a 70/30 joint venture between Freeport Gold Company and FMC Gold Incorporated, both of which are wholly owned affiliates of the respective parent companies, Freeport-McMoRan, Inc. and FMC Incorporated. Under the terms of the joint venture agreement, Freeport Exploration Company, another Freeport-McMoRan affiliate, manages the exploration and pre-mine development. Drilling, design, construction and management of the Bell Mine are provided by Freeport Gold Company.

Jan 1, 1982

By J. W. C. Wong, S. D. Miller, J. J. Jeffery

Pre-mining identification of acid forming mine and waste materials is of concern to the mining industry because of the potential for the generation of acid mine drainage, acid rock drainage, and soil acidity problems. Accurate identification of acid forming material is essential for developing appropriate waste management strategies to reduce environmental problems related to acid generation from sulphide containing wastes. The acid-base accounting procedure, in its various forms , is commonly used for pre-mining screening of mine and mine waste materials. The procedure is generally effective when used and applied correctly but is prone to incorrect interpretation of results which can have significant financial and environmental implications. This paper examines the acid-base accounting Procedure and the possibility of misuse of this method with special emphasis on the sampling method, the sulphide forms, the acid neutralization capacity, and the interpretation of results. Data from numerous coal, base metal, and gold mining operations are used to illustrate the application of the acid-base account. The data base indicates that overall, approximately 1/3 of all waste generated by mining and mineral processing is potentially acid forming indicating the need for correct identification and management. Problems associated with simple application of 'absolute' acid-base criteria for classifying acid forming material are highlighted and the need for developing site specific or 'relative' criteria is discussed and illustrated by case study.

Jan 1, 1991

By N. S. P. Kumar

INTRODUCTION Development work at Carr Fork Mine of Anaconda Copper Company in Tooele, Utah commenced in August 1974. A decision to install an underground gyratory crusher for primary crushing run-of-mine ore and waste was made in 1976. Higher throughput rates, larger reduction ratios and greater flexibility in terms of meeting immediate and expanded production needs were the main reasons for selecting the gyratory crusher over the jaw crusher. UNDERGROUND MATERIALS HANDLING Underground crushing and conveying system was designed for a capacity of 16,300 mtpd of ore and waste on a 2-shift, 5-day week basis. Engineering and design of crusher complex was performed by Anaconda engineers at Carr Fork. Figure 1 represents the longitudinal section of mine showing the general materials handling system. Mine area is trackless except for materials and production haulage which is run on rail track on both 1200 and 970 levels. Ore from stopes and waste rock from development headings are handled by 3.8 cu m (5 cu yd) Jarco scoops and dumped into 2.4 m (8 ft) diameter ore and waste passes at the 1200 level. The material gravitates down to the 970 level where it is loaded into 12 cu m (420 cu ft) ASEA mine cars using side loading chutes. The muck train, consisting of 15 to 18 cars and two 27 mt General Electric trolley locomotives, is hauled over a distance of 2,300 m (7,550 ft) to

Jan 1, 1981

By T. D. Rourke, E. J. Cording, O&apos

INTRODUCTION Detailed investigation of a 60-ft-deep excavation in a mixed profile of sands and stiff clay was performed by the University of Illinois for the Washington Metropolitan Area Transit Authority (METRO). The work was coordinated through DeLeuw, Cather and Co., the General Engineering Consultant of METRO. Instrumentation was concentrated in a portion of braced excavation for the Gallery Place Station near the intersection of 7th and G Street. The early construction date, the 60 ft depth of cut, and the proximity of large buildings formed the basis for selection of this site as the focal point of observation and measurement. A history of lateral and vertical displacement is provided wherein movements which occurred during excavation to the full depth of cut and, subsequently, during station construction and the removal of braces are described in detail. Observations of preloading and the consequent brace loads and wall displacements are described. The effect of temperature change on brace loads is discussed and the measured apparent earth pressure for the 60-ft cut is provided. The paper discusses the relationship of lateral displacements of the cut wall to the construction procedure, and compares the lateral wall displacement with both lateral and vertical movement in the surrounding soil mass. Based on observed movement, the method by which displacement was predicted for a nearby 82-ft-deep excavation is described. The performance of the 82-ft-deep excavation has been summarized elsewhere (2).

Jan 1, 1974

By Jean-Michel M. Rendu

According to statistical theory, the geostatistical methods of ore reserves estimation are greatly superior to any other method. However acceptance of geostatistics by the mining industry has been slow and not as wide spread as one would expect. One of the reasons for this cautious approach is that it is often questioned whether the geo- statistical assumptions are satisfied in real world situations. When blocks of ore are estimated in a mineral deposit, geostatistical theory can be used to determine which method of estimation should give the best results. Using this theory, the relationship between estimated value and true block value can be quantified. There is a need to verify that this theoretical relationship is actually observed in practice, and that the block estimates ' obtained using the theoretical ly best method of estimation, are actually most similar to the true block values. In this paper the results expected according to the theory are compared with the results actually obtained. Sample values from a large bedded gold deposit have been used. Blocks of ore have been estimated by a number of methods, including the polygone, inverse power of the distance, kriging, logarithmic kriging and other geostatistical methods. The block estimates have been calculated from samples on a large grid, and compared with the true block values obtained from additional samples on a much smaller grid. The results of this comparison show extremely good agreement between theory and actual results.

Jan 1, 1979

By Robert G. Lundquist

REAM (for Rapid Excavation And Mining) is a method of rock fragmentation by high-velocity projectile impact developed by Physics International Company. This paper reports the results of field testing over the last two years. The success of the method is based on the fact that the amount of rock broken per shot scales nonlinearly with projectile impact energy. Thus, high energy impact yields spectacularly low specific energies for rock breakage. The field work reported used 90- and 105-mm military guns to accelerate 8-1/2 and 10-pound concrete and steel projectiles to velocities of 5000 to 5500 fps. All tests were performed in a competent 25,000 psi granodiorite at Hope Valley, California. During the first year of field testing 26 feet of 13-foot-diameter tunnel were produced with the 105-mm gun. The first 20 feet of this tunnel were line-drilled to aid in producing a stable portal. During the second year the tunnel was extended an additional 29 feet using the 90-mm gun. The 55-foot tunnel was produced by 590 shots. Between 1-1/4 and 1-1/2 tons of granite were broken by each shot. A silenced 90-mm gun was placed underground and the tunnel portal closed with a steel barrier. Overpressures of less than 1 psi were measured on the inside of the barrier, corresponding to an impulse noise of about 170 db. The muck produced was similar to drill and blast muck. Overbreak and ground support problems appeared to be less than with drill and blast. The contour of the tunnel was easily controlled using the 90-mm gun; the tests were also conducted using a 57-mm gun for trimming. Projections indicate that advance rates with REAM will be three to seven times faster than drill and blast, at less than two-thirds the cost. This is based on the development of a fully integrated continuous system and an inexpensive propellant giving a total expendables cost of less than $3 per shot. Other applications of the REAM technology are found in secondary breakage for open pit mining, in drilling large diameter holes, and in underground mining for longwall mining, overhand stoping, and raising.

Jan 1, 1974

By A. L. Mular

Steady-state material balances calculated from data measured at various locations around process units are useful for many purposes, such as metallurgical accounting, on-line control, and the development of mathematical models. Often it is possible to calculate material balances by several independent procedures when excess measurement information, i.e., redundant data, is available. Clearly, if the data were collected without measurement errors, a theoretical condition never found in practice, all material balances calculated from redundant data would be in agreement. The real situation is that error exists in practical measurements, so that the results of material balances determined from available optional procedures differ. Consequently, best fit computational procedures to improve the material balances by taking measurement errors into account have been formulated. Such procedures can be used also to judge whether measurements are grossly in error due to either faulty observations or defective data sensing devices. A variety of mathematical techniques are available which serve to adjust raw data. The adjusted data permit mass balancing that does not depend on the computational method. To illustrate the need for an adjustment procedure, Table 1 shows a raw data set acquired around the Brenda Mines Ltd. No. 4 grinding circuit shown schematically in Fig. 1. At least seven optional ways to calculate a circulating load ratio may be employed. These are shown in Table 2 where, depending upon the calculation [ ]

Jan 1, 1979

By Q. Xu

The new process consists of the selective coalescence of fine hematite particles by fine magnetite. The gangue minerals are dispersed by some dispersant; thus it can be separated by desliming. This process is particularly suitable for fine-grained hematite/magnetite-type deposits.

Jan 1, 1989

By R. V. Ramani, R. Srikanth, R. Zhao

A two-part study was conducted to understand the factors affecting respirable dust generation potential or dustiness of coal seams. In the first part, the data from three prior comprehensive laboratory studies was analyzed to establish quantitative relationships between respirable dust generation potential and coal characteristics. This analysis indicates that respirable dust generation rate is positively correlated with Hardgrove Grindability Index (HGI), fuel ratio (fixed carbodvolatile matter), Vitrinke Reflectance (VR), and Level of Organic Metamorphism (LOM). In the second part, specially-designed single breakage experiments were conducted to determine the primary dust generation potential of 17 coal samples obtained from four continuous miner sections, three longwall sections, and the Penn State Coal Data Bank. The single breakage study indicates that primary dust generation rate is positively correlated with fixed carbon content, fuel ratio (fixed carbon/volatile matter), VR, and LOM. Since VR and LOM are strongly influenced by the process of coalification, differences in respirable dust generation rates in different coal seams may be explained by the thermal metamorphism of sedimentary organic matter during subsurface burial.

Jan 1, 1995

By K. A. Prisbrey

Mineral carbonation is the reaction of carbon dioxide with mineral silicates to form solid, carbonate compounds. The carbonate ion holds carbon in a low energy state – lower than in carbon dioxide. Thus the reaction of carbon dioxide to produce mineral carbonates captures the carbon in a stable, solid form. The University of Utah is investigating the carbonation of silicate minerals by mechanochemical processing, which has the potential of being much less expensive than other methods. Tests to date have shown that a marked change takes place in the lizardite variety of serpentine after 15 to 20 minutes of intense grinding in the presence of gaseous CO2. Further testing is in progress.

Jan 1, 2004

By R. Herrera-Urbina, D. W. Fuerstenau

A large number and a wide variety of chemical reagents are used in flotation processes for wettability and Eh control, particle agglomeration/dispersion and bubble stability. A historical account of the use of flotation reagents through the years since flotation was introduced as a viable and economic process for the concentration of sulfide minerals is given and a review of old and modern postulates of their interaction with minerals is presented. Although the results of surface and colloid chemistry studies with well characterized mineral/flotation reagent systems have advanced our understanding of the role played by these chemicals in the flotation process, many questions remain unanswered. Moreover, new flotation reagents are needed to solve the challenge posed by the treatment of problematic-type ores and fuel deposits that have increasingly become the source of our raw and energy materials. Because of the depletion of high-grade and relatively easy-to-process ores, flotation scientists and engineers are confronted with finding more specific and selective flotation chemicals to effectively and economically concentrate minerals. The development of new flotation reagents is vital for cleaning fine coal and processing polysulfide, polymetallic ores, and mixed oxide/sulfide ores.

Jan 1, 1989

By V. Rajaram, D. P. O’Connor, L. Sakamoto

In 1988, the Metropolitan Water Reclamation District of Greater Chicago (MWRD) imposed a no-blasting specification (blasting is restricted to the construction shaft and shaft bottom or boot) on the Deep Tunnel project. This was prompted by numerous complaints from residents in the vicinity of the project and controversies experienced on previous projects from blasting the rock overlying the tunnel. This paper will describe the methods used by two major contractors driving 20 km (12.5 miles) of tunnel, and drilling more than 36 shafts under this restrictive specification. The impacts are detailed on design, construction, schedule, cost and the environment.

Jan 1, 1993

By R. P. Upadhyay

The Deserado Mine, located in northwest Colorado, is an underground coal mine designed to produce 1.225 million tons (1.35 million short tons) of clean coal per year for the Bonanza Plant located in northeastern Utah. Coal is transported to the power plant via a 61 kilometer (38 mile) captive railroad. Most of the surface facilities and the stationary underground equipment is controlled and continuously monitored by the computers located at the surface control room. In addition to system control, the computer also continuously monitors vital environmental conditions using sensors located at various critical locations underground. The system's advantages are increased mine productivity and safety.

Jan 1, 1988

By V. I. Lakshmanan, P. D. Tackaberry

The use of activated carbon as an alternative to Merrill Crowe precipitation to recover gold from pregnant leach solutions is recognized. Recovery using activated carbon, however, suffers from the interference, due to organic fouling, clay content and increasingly from the presence of elements such as copper. Ion exchange separation technology is familiar to the mining industry (uranium) and its potential application to the gold mining industry is evaluated with considerable efforts by research workers in South Africa, Australia, and North America. The present paper reviews in detail the status of the research work that identifies potential opportunities.

Jan 1, 1990