Search Documents

By Ezra L. Kotzin

Foundry sands used to make molds and cores have been very important to foundrymen since metal casting began hundreds of years ago. They are now used in two basic ways, either in an uncured green state, grain-bonded with clay, or in a set cured state achieved with sand that, mixed with resins or oils, is cured by baking or by chemical reaction. The term sand, as generally used in foundry applications, may best be defined as material composed of granular particles of mineral matter, ranging in size from 0.5 to 2 mm in diameter. The particulate nature of the material may be the result of natural disaggregation or result from crushing and screening of rock or ceramic materials; crushed and screened products are sometimes referred to as "manufactured sand." Based on their origin, the raw materials for foundry sands will vary in grain shape, grain composition, relative surface, grain size, and grain distribution patterns. These properties, in addition to their chemical analyses, sintering point and expansion characteristics play an important part in the choice of sands used as the base molding or core aggregate in metal casting. Sands with different origins may be blended to produce specific compositions and grain size distributions. Early raw material requirements based on silica sand were simple, but as sand/core/mold technology became more sophisticated and binder technology continued to be developed, the physical properties of foundry sands became more critical. Silica sand is composed of quartz, along with, in most cases, small amounts of feldspar, mica, clay, and other common minerals. Although silica sand is still by far the most widely used base material in production of molds and cores used in metal casting, other natural mineral sands have their own unique characteristics and fill an important niche in special applications. As a result, the term sand, as applied to raw materials used in metal casting, has been logically extended to include granular materials composed of a group of minerals other than quartz. With increased use in advanced foundry technology, natural sands composed predominantly of zircon, chromite, staurolite, or aluminum silicate minerals and of granularized chromite or olivine, have become more than just alternate materials and are now commonly classified as sands when the grains are sand-sized. Foundry sand may therefore be considered under two categories: silica sands and non-silica sands.

Jan 1, 1994

By Thomas F. Stinson

Energy-producing states see severance taxes as attractive sources of increased revenues for otherwise tight budgets. Consumers in energy-poor states, however, protest that current rates are excessive and have moved to obtain a reduction. The US Supreme Court heard two cases questioning such taxes during its 1981 term, and Congress, in each of its last two sessions, has seriously considered measures placing a ceiling on severance tax rates. Although discussions usually focus on coal severance taxes levied by Montana and Wyoming, ramifications of changes in national policy are much larger, potentially affecting mineral taxes in all states. Severance taxes yield substantial revenues in some states, as illustrated in the accompanying table. In fiscal 1980, Texas collected more than $1.5 billion from such taxes, while Louisiana, Alaska, and Oklahoma collected $525 million, $507 million, and $436 million, respectively. Oil and natural gas production were the major items taxed. While the table shows only the 10 states with the largest severance tax collections, a total of 17 states had severance tax receipts exceeding $10 million in 1980. The enormous increases in severance tax revenue between 1970 and 1980 can be seen from the table by comparing columns A and B. For the 10 states shown, revenues increased from $650 million to $3.8 billion during that period, due to a combination of higher prices, increased production, and new or increased taxes. In most states, increases in prices and production were more evident than higher tax rates. Although the revenue increase is impressive, it understates the extent of changes occurring during the past decade. Since tax collections are shown for fiscal 1980, the full impact of the decontrol of domestic oil prices is not evident. Also, taxes on natural gas reflect controlled prices. When full de-control of natural gas occurs, significantly higher revenues can be expected in gas-producing states, even if tax rates, production, and world prices remain constant. These increases in severance tax revenues, coupled with further increases expected to accompany natural gas decontrol, have produced fears that a substantial transfer of income is taking place from residents of energy-poor states to those living in energy-rich areas. Others worry that increased severance tax revenues will be used to substitute for a substantial portion of state taxes that would have otherwise been collected from firms and individuals. The resulting improvements in tax climate, it is thought, may encourage firms and workers to migrate to energy-producing states. While these issues are often portrayed as pitting energy have-nots against the haves, such is not entirely the case. Much of the original impetus for limits on coal taxes came from Texas residents, the state collecting the most severance tax revenue. One way of gaining perspective on these concerns is by examining severance taxes per capita and as a percent of state tax collections (see columns C and D in the table). When this is done, Alaska, where 1980 taxes on oil and gas production totaled more than $1300 per capita (and 35% of all state tax collections), stands out as a special case. There, the state was able to eliminate some individual taxes, place revenues in a permanent trust fund, and consider offering a rebate of some previous income

Jan 4, 1982

By W. Hitchcock

To enable the analysis of stability for a mine feasibility study a variety of geotechnical engineering parameters need to be obtained. At the early stage of a project it is usual for those responsible for the study to require a wide spatial distribution of RC holes in order to define a resource at the lowest possible cost. By the time a geotechnical study has commenced drilling priorities have usually switched to improving the definition of a resource, by drilling with diamond coring methods in the central area of the main orebody. The usual timing for geotechnical data collection is therefore after a wide distribution of holes have been drilled but which contain little geotechnical information. Conventional methods employed usually involve estimation methods, including book values and examination of disturbed core, or expensive additional drilling. With downhole geophysical methods we can economically take advantage of existing holes to obtain continuous values for density, defect orientation and ranking, elastic modulus values, unconfined compressive strength estimates and fracture frequency. This paper presents the results of a geophysical study and discusses the advantages and potential pitfalls of the method as compared to conventional methods of data collection.

Jan 1, 1999

By James H. Boettcher

Inflation and increasingly complex tax laws in the United States combined with rising national ism overseas have made the structuring of viable financing plans which meet the requirements of the various parties involved equally important in determining project success as the design of an efficient mining plan or selection of the optimal size equipment. Whereas the use of computerized analysis to design and evaluate the technical parameters of resource ventures is well accepted, computerized evaluation of the investment criteria (qualitative and quantitative) of the various parties to the project (mining firm, financial institution, product buyer, host government, etc.) is a more recent application which can make a material impact in strengthening project economics. By identifying the objectives of the parties and critically evaluating and testing them with the technical and economic/financial constraints on the project the sponsors can design a financial structure tailored to the attributes of the deposit. A myriad of new financial techniques have evolved for financing natural resource ventures, from "Commodity-backed bonds" to tax based limited partner- ships, but in every case the structure of the financing mechanism depends on carefully matching the parameters of the financial structure with the economic characteristics of the project and the objectives of its sponsors. This presentation outlines a methodlogy for computer based project evaluation in the design and structuring of stronger financial plans for natural resource ventures.

Jan 1, 1982

By Jack J. K. Daemen

A wide variety of subsidence prediction methods exist. They can be classified into empirical methods and mechanistic models. The empirical methods include profile functions and influence functions (Brzuner, 1973a,b; Kratzsch, 1974; Berry, 1978; Hood et al., 1981), the two empirical approaches of most practical value, if only be- cause they are readily programmed on calculators or computers. The profile functions have the advantage that they allow for ready determination of the necessary empirical parameters from field observations. They have the disadvantage of being restricted to subsidence calculations at a very limited number of points or lines above very simple (rectangular) mine geometries. This reduces greatly their practical applicability for damage predictions, which usually require estimates of strains, slopes or curvatures at structures that have arbitrary position and orientation with respect to planned mine excavations. Influence functions can be used to calculate subsidence at any point near an excavation of any in- seam outline. The main difficulty associated with empirical influence functions is the lack of uniqueness in the relation between subsidence and its cause, the convergence distribution over a mined excavation and its immediate surroundings. A secondary practical difficulty is the need for fairly arbitrary adjustments near the excavation edges, usually in the form of compensation zones (e.g. Brsuner, 1973; Hood et al., 1981). Determination of the appropriate empirical constants in influence functions is facilitated greatly when a direct mathematical connection exists between influence and profile function (several examples are given by Brauner, 1973 and by Hood et al., 1981), so that field data can be used to determine the parameters through backfitting of the profile functions, which is considerably simpler and more direct than backfitting of influence functions.

Jan 1, 1982

By E. W. Hawk

he power generation industry may be required to reduce carbon dioxide (C02) emissions if regulations related to global climate change are enacted. Coal-fired generation emits more than 80% of the power sector CO2 and would be a likely target for CO2 reductions. Compliance with the Kyoto Protocol will require a 33% reduction from the projected year 2012 emission level, even with moderate load growth. This article describes an analysis of power industry CO2 reduction options and their costs. It assesses how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered. The Global Climate Change Treaty signed at the Rio de Janiero Earth Summit in June 1992 set the long-term goal of stabilizing CO2 concentration in the atmosphere. The December 1997 Kyoto Protocol established short-term mandatory targets for the United States and 37 other developed countries. The United States' target is a 7% decrease by 2012 from the 1990 "greenhouse gas" level. Developing countries are exempted from reductions, according to the Kyoto Protocol, despite projections that indicate a significant increase in their emission levels. The Kyoto Protocol must be ratified by the US Senate. US power industry carbon emissions were 490 Mt (540 million st) in 1990 and are projected to be 680 Mt (749 million st) in 2012, according to the US Energy Information Administration. Coal-fired generation emits more than 80% of the power sector CO2. Assuming that the power industry is only required to reduce emissions by a proportional share, a 33% emission reduction, or 225 Mt (248 million st) of carbon, would be required to comply with

Jan 1, 1999

A chartered bus with about 30 attendees of the just completed 1998 SME Annual Meeting headed toward Green Cove Springs, FL, which the author had been told was located somewhere south of Jacksonville, FL. In conjunction with the meeting in Orlando, RGC (USA) Mineral Sands provided a tour of its facility. The author had worked with heavy minerals on a laboratory scale, performing the usual gravity and magnetic separations, but had never been to a heavy mineral mine and processing facility. Years ago as a metallurgist, the author once applied for a job in a heavy mineral operation in Florida -it may have been the same operation. After turning north on to Highway 95, the endless billboards promoting beach-front retirement communities proved the Atlantic ocean was just a few miles away (although the author never caught a glimpse of it). After another hour, the bus suddenly turned west and continued inland for about 65 km (40 miles). The thought occurred, "We are talking about beach sands, what are we doing heading away from the ocean?" As the bus continued inland, the author was struck by the flatness of the land and by the lakes, rivers and wetlands. He was also impressed by the many fine stands of pine and hardwoods. The office of RGC (USA) Mineral Sands is located about 16 km (10 miles) south of Green Cove Springs. Upon leaving the bus, members of the tour were greeted by Graeme Sloan, general manager, and Elliot Mallard, manager of mining. They provided some general information about the operation, including a slide show. RGC's Florida operation produces four concentrates: zircon (ZrSiO,), rutile (TiO,), ilmenite (FeTiO,) and leucoxene (an alteration product of ilmenite containing 67% to 70% TiO,). With a work force of about 170, the annual production of the above products is about 23,27, 45 and 14 kt (25,000 30,000 50,000 and 15,000 st), respectively. RGC also has other mineral sand operations, in addition to gold and base metal mines, mostly in Australia.

Jan 1, 1998

By Brad C. Lewis

The coal mining industry has experienced a general trend toward longwall operations. An increasing percentage of underground coal is being mined by longwalls. And productivity in longwalls is likewise increasing. Operators of longwalls, however, have not yet reached a state of mining euphoria. Competitiveness within the industry and from alternate fuel sources is forcing continued pursuit of higher productivities and lower costs. [Figures 1, 2 and 3] present trends in the industry. Longwall mines, as defined here, are those reportedly having longwall installations in each of the respective years. Production from both the continuous miner and longwall units is included in the longwall mines. Nonlongwall mines are all other underground mines. Productivity calculations are based on total employee-hours associated with the operation. Annual percent increases in productivity appear to have peaked in the 1985-1987 time frame. This was due, in part, to implementation of technological advancements and improvements in management-labor relations. The results shown in [Fig. 3] aroused the author's curiosity. The first question was "Have technological advancements to increase productivity peaked?" It does not appear so.

Jan 1, 1990

By H. J. M. Rose

Arising out of the world energy crisis and the increasing demand for nuclear fuels, the Elliot Lake operation of Denison Mines Limited is currently expanding its facilities to meet its increased contractual obligations of some 90,500,000 kg of uranium oxide between now and the year 2011. The mining of uranium is subjected to increasingly stringent environmental controls by governmental and associated agencies so as to safeguard the health of the employees. A heavy burden of responsibility is thus placed on the Ventilation Department to ensure, through efficient planning and good control, that satisfactory ventilation conditions prevail throughout the entire operation. Management realized at the outset of the present phase of this expansion, that the establishment of a properly organized and administered Ventilation Department would be essential to ensure that long term production goals are achieved within the numerous constraints imposed by existing legislation. The paper describes the formation of the department by recruiting technically competent, but largely inexperienced, ventilation personnel, their practical training programme, the departmental structure and the operational and control responsibilities of the ventilation staff.

Jan 1, 1980

By Gregory Owen Lewis

The use of gravity concentration as a means of recovering the 'free' gold component from alluvial and milled ore products is widely used and is receiving increasing attention, particularly with the introduction of the centrifugal-type concentrating units. Because of ever-increasing mining and processing costs and a decline in the gold price, it has become important that the recov­ery efficiency from concentrates is improved so as to increase the yield of bankable gold from this primary recovery step. This paper outlines an alternative hydrometallurgical approach aimed at achieving overall gold recoveries in excess of 98%, together with the elimination of any secondary residue streams which, in the case of conventional treatment methods, require re-processing. An adaptation to the Minataur™ Process technology is being applied with the proposed method, incorpo­rating the pre-treatment of the concentrate, oxidative leaching of the pre-treatment residue, followed by precipitation of a high­purity gold. This route is seen to have application in all scales of operation. Selected results from laboratory-scale testwork are presented to highlight the discussion.

Jan 1, 1998

By Zhang Youdi

A two-step approach has been developed for surface mine short term planning by the authors. The first step is mid term control and planning by the use of Goal Programming. This step gives optimal results for mid term planning (i. e. yearly or quarterly mine plan) as well as a macro control for short term planning (i. e. monthly or weekly plan.) The second step of the approach deals with short term production scheduling by the application of CAD technique and Systems Simulation. An interactive color character graphic design system has been developed with a software package. The menu-driven and module- structured package provides sufficient functions for surface mine short term planning and makes the model very flexible and user-friendly. This model has been applied to a large surface coal mine for short term planning optimization. Satisfactory results have been obtained. It is concluded that for complicated mining conditions this two-step combined approach gives an optimal control of mid term planning, makes the short term planning easier to avoid blindness; it has been proven that the Goal Programming is a powerful tool for solving multi-objective decision-making problems; guided by GP mid term planning, the CAD technique and simulation software package for short term planning are able to be concentrated on their practicality and flexibility.

Jan 1, 1992

By Andrzej Walentek

This paper presents the results of numerical modeling of the fractured zone around longwall gateroads. The numerical computations have been based on the results of underground measurements of the fractured zone around longwall gateroads, which were performed for various geological and mining conditions and measured with the use of the endoscopic method with a digital camera. Having results of the underground investigations, trials of duplicating them by the Finite Element Method using software PHASE and the Hoek-Brown failure criterion were performed. In order that the fractured zone predicted by the model-based computations closely simulate that measured underground, some selected parameters in the Hoek-Brown failure criterion were modified based on the earlier determined relations used for prediction of the roof-to-floor convergence in longwall gateroads. As a result, the model-based computations produce results very close to those obtained from the underground measurements. Determination of the fractured-rock zone around the mine roads is of great importance to mining practice, especially in planning and designing supports for longwall gateroads. The influence of the front abutment pressure causes the fractured rock zone around the roads to increase and results in an increase of support load. Moreover, proper determination of the fractured rock zone is one of basic elements in the process of planning roof bolting for mine workings.

Jan 1, 2009

By Majid Sadeghi, Ali Naghi Dehghan, Kaveh Ahangari, Seyed Mahdi Pourhashemi

"Instrumentation and monitoring of ground deformations in tunneling is a principal means for selecting and controlling the excavation and support methods among those foreseen in the design, for ensuring safety during tunnel construction (including personnel safety inside the tunnel and safety of structures located at ground surface) and, finally, for ensuring construction quality management. In this paper, the effect of Hakim Tunnel excavation on the behavior of the surrounding ground was investigated based on the geotechnical instrumentation. This tunnel with 1080 m length, 18 m width and 12.6 m height is being constructed using the SEM/NATM along the Hakim Highway in Tehran. The results which are obtained from recorded displacements by geodetic pins (on the tunnel wall and roof), extensometers and settlements pins (at the ground surface) demonstrate the tunnel stability during the various stages of excavation. However, it is concluded that the rate of excavation in different sequences could have a major role on stability of tunnel. In this case the surface and underground openings were monitored as well as needed for controlling the face probably collapse. INTRODUCTION Tunneling is increasingly being used world-wide to provide the infrastructure required for sustainable urban areas. The high demand for space and the disturbance of existing infrastructures by construction measures increasingly forces future infrastructure projects to be conducted underground. One of the important purposes of tunneling projects in urban area is not only to minimize displacements but also to control them during the construction (Pourhashemi et al., 2015). Normal method of tunnel stability analysis is not able to evaluate the real rock and soil mass behavior. Hence, instrumentation is a practical method to monitor displacements, to evaluate the stability of underground openings, and also to determine the rock and soil mass properties (Dehghan et al., 2012. Dehghan, 2013). Rocks and soils are materials with properties that can change instantly and significantly from one point to the next. Some complications may often happen due to uncertainties in the loads that the new facility must withstand during construction and operation. Instrumentation and monitoring provide quantitative information on actual behavior of ground and adjacent structures. A lot of deformation monitoring studies for determining and analyzing different kinds of engineering structures such as tunnels, bridges, high-rise buildings and dams are implemented. Considering the type of the structure, its environmental"

Jan 1, 2016

By Prakash M. . P. E. Donde

1. INTRODUCTION The Washington Metropolitan Area Transit Authority (WMATA) has often taken a leading role in introducing innovative construction technologies to build its transit system. Most recently, Contract Section E-5a, which included Fort Totten Station and Tunnels was constructed utilizing the New Austrian Tunneling Method (NATM) in soft ground. Along with the station and tunnels, two permanent shafts were also constructed in soft ground employing the NATM technique. This project is located within the District of Columbia on the Greenbelt Route. The subject of this paper is to discuss the unique method of construction of these two shafts, and explore the benefits of applying the NATM technique to the construction of deep shafts. The design of the shafts was performed jointly by Jenny Engineering Corporation of Springfield, New Jersey, and Mayreder Consult of Linz, Austria. The designers also provided construction support services and a resident NATM expert at the site during construction. The construction of the project started in April 1988 by a joint venture of Mergentime Corporation and H. T. Construction, a subsidiary of Hochtief Company from Germany. This $48.7 million construction project has been completed. 2. SUBSURFACE CONDITIONS The two NATM shafts are located primarily in Cretaceous-age deposits that are over 100 million years old. These deposits are intermixed and lenticular in nature

Jan 1, 1993

By Guillermo Krstulovich

Pillar strength is a fundamental variable in the design of room and pillar mining. A number of researchers have investigated the strength of mine pillars by loading cubical, cylindrical and rectangular model pillars to failure in a compression testing machine (1). Several of these researchers have observed an increase in the compressive strength of model pillar with an increase in friction at the platen-specimen interface (2, 3, 4, 5). It has been postulated that the friction prevents lateral expansion of the specimen, thereby exerting a confining pressure at the interface. Seldenrath and Gramberg in their work with cylindrical specimens of limestone and marble noted that the effect of clamping the ends of the specimens, i.e., to restrict lateral movement of the specimen face, was to increase the compressive strength about 10% for marble and from 50-75% for the limestone, as compared to the same type of specimens when tested with the end planes free (6). No attempt was made to determine the confining pressure exerted by the clamps. In recent years, Bureau of Mines has conducted an extensive study, similar to Seldenrath and Gramberg's, with dog bone specimens. The confining pressure exerted by the clamps was determined and an increase in the compressive strength with increasing confining pressure noted (7, 8).

Jan 1, 1970

By Richard Meriwether Smith

Mining-related earthy bodies in contact with the atmosphere are now counted, generally, as minesoils. Because soils within this broad category are extremely young the influence of parent material is stronger than in older soils, where climate, organisms, and topography have had time to interact with near-surface rocks to form more distinctly differentiated profiles. Understanding of minesoil properties and processes is aided by definitions of rock types in terms of chemical, physical, and mineralogical characteristics that are, with some degree of consistency, translatable into soils. Geological correlations based on age or sedimentary sequences are helpful if they assure details of mineralogy and lithology, but our pedologic objectives demand that any conflicts involving rock types must be resolved in favor of distinctions having strongest implications for soil properties after mining. Chemically this approach emphasizes accounting of potential acid-base status, plant nutrient availability by adapted and calibrated extraction procedures, and absence of biotoxins. Physically it anticipates particle sizes, shapes, and arrangements in readily pervious soil profiles that will favor plant growth with desired levels of moisture and oxygen. Concurrently we are considering soil property suitability for uses other than growth of plants. Above all we need to be able to predict pedogenic processes in the particular environment, including rate as well as direction of chemical and physical change.

Jan 1, 1974

By John Bailey

Stressmap is a program whereby the earth's stress field is charted in detail and utilized for design of mines and mine exploitation. This program is implemented by mapping the attitude (location, direction, dip, and extent) of induced rock ruptures during the process of hydrafracturing drill holes contiguous to mine interest. The program includes utilization of ancillary naturally occurring stress relief signals, They are precipitated because the earth is indeed dynamic and the strata of the crust are continually adjusting to load and/or strain differentials resulting in rock deformation and fracturing. These fracturing adjustments occur as small to tiny earthquakes comparable to Richter magnitudes of one, zero, minus one, and smaller events termed microearthquakes. Obviously, the earth's stress field changes due to continued differential loading and crustal movements; therefore it becomes conspicuously evident that resolving today's stress field as opposed to paleostresses is most important for efficient, economical, and safe mining operations.

Jan 1, 1974

By D. Royston, D. Denlay

Pulp lifters are used to discharge ground pulp from non-overflow grinding mills. In straight-radial channel pulp lifters, discharge is often incomplete and back-flow down the pulp lifter can occur. Leading-curve channel pulp lifters can be used to ensure complete discharge, especially at high mill rotational speeds. The complex motion of solid materials in pulp lifters has been modelled mathematically for both straight-radial and curved pulp lifters in order to make comparisons between the two types. The model is supported by practical observations of the performance of curved pulp-lifters in a commercial 24ftSAG Mill as well as observations of the discharge from several commercial straight-radial pulp-lifter AG/SAG Mills.

Jan 1, 1999

By Kal V. S. Sastry, Stephen N. Little

Computer simulation of comminution systems is found to provide significant cost savings by enabling efficient circuit design and development of control systems. These simulation systems are based on sound mathematical models and numerical methods. Nevertheless, they are found to be hard-to-use and hard-to-modify to carry out more elaborate process analysis. This paper discusses the fundamental principles and practical aspects of an advanced, highly functional, and user-friendly SIMulator for COMminution, SIMCOM, that is being developed at Berkeley by incorporating state-of-the-art software engineering principles.

Jan 1, 1992

By Z. Rogovin

A Knowledge of the amount of time the material spends in a continuous mill in a closed-grinding-circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of tracers in residence-time-distribution (RTD) experiments. In a typical wet process the RTD measurements are usually done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article a simple to use mathematical method for the calculation of the closed circuit material residence time in the mill is developed. Using this method there are no restrictions on the location of the tracer injection or detection points. Any convenient location in the closed circuit can be chosen without affecting the simplicity of the method. This method also enables the calculation of the degree of mixing in the mill. The use of this method for the analysis of impulse response data obtained from several commercial grinding circuits is presented.

Jan 1, 1986