Search Documents

By Jessica M. Wempen, Dallan J. Coons, Bailey S. Simmons, Michael K. McCarter

Gate-road yield pillars are subject to increases in stress as the longwall face advances toward the pillars. Increases in pillar stress can be inferred by measuring roof/floor convergence surrounding the pillar. This paper presents a case study of convergence measurements surrounding a two-entry gate-road yield pillar in the head gate of a coal mine. Convergence was measured over a six-month period, as the longwall face approached and passed the pillar. Measurements were collected at eight locations surrounding the pillar: four locations in the travelway and four locations in the beltway. In addition to convergence stations, the pillar was instrumented with an array of seismometers. In future analysis, convergence measurements will be compared to seismic interpretations. This study reports on the geology and geometry of the longwall panel, the roof and rib support, the change in convergence over time, and the physical properties of coal and parting. Additionally, the convergence measurements are compared to pillar safety factor distributions derived from a finite element model. The convergence measurements contribute to the knowledge of when yield pillar abutment loading, caused by the encroaching longwall, is first detected. Knowing when abutment loading begins to yield the pillars can help define when standing secondary roof supports are required for head gate entry support.

By F. F. Peng, D. C. Yang, G. Yanief, E. H. Cho

This study deals with carrier flotation of cerium dioxide, a surrogate of plutonium oxide, which is the major contaminant at the Nevada Test Site (NTS). The objective of this study was to determine the feasibility of using carrier flotation for remediation of the site. In this study, a - 200-mesh fraction of pure cerium dioxide was used. Oleic acid was used as the collector, while calcium carbonate was used as the carrier. Mechanical-cell tests were conducted to float the surrogate from a mixture containing uncontaminated NTS soil, both in the absence and presence of the carrier. It was found that the addition of the carrier drastically enhanced the flotation recovery of cerium dioxide. The flotation recovery of the surrogate increased from 34% to 65% by adding only 0.5% calcium carbonate (-150 mesh). The recovery further increased to 95% by adding 10% calcium carbonate. The flotation method utilizing a carrier of calcium carbonate seems to have a high potential for the remediation of the soil contaminated with radionuclides at the NTS.

Jan 1, 1998

By Rodney H. Sergent

After being forgotten or ignored for nearly 100 years, the ability of bromine chemistry to extract gold from ore has been rediscovered. While bromine chemistry is similar to chlorine, there are some important differences. Bromine in its elemental form is a dense, fuming, red liquid. Elemental chlorine is a gas and requires a substantial amount of equipment to handle, store and deliver to solution. Bromine has an advantage in its ability to rapidly and completely oxidize heavy metals to water soluble halide salts. The first patent for use of bromine chemistry for gold extraction was issued in 1881 (1). By 1895, work done in Colorado concluded well roasted ores required approximately 1-1/2 lbs/ton of elemental bromine for superior extraction of metals (2)). At that time, bromine was deemed to be cost effective vs. chlorine even though it was more expensive on a pound basis than chlorine. The advent of cyanide technology virtually eliminated both chlorine and bromine from consideration for leaching of ores. Cyanide was so inexpensive that it made deposits requiring unique technologies unattractive for mining. Only since the deregulation of gold price has bromine/chlorine technology been considered for those ores not amenable to cyanide. While chlorine has found its way into the pretreatment steps, bromine is just beginning to realize its niche in the marketplace.

Jan 1, 1998

By Douglas W. Fuerstenau, Douglas M. Deason

The depletion of high grade siliceous phosphate ores is bringing about a search for economically processable replacements. The processing of unexploited dolomitic sedimentary phosphate reserves has numerous problems including the similar surface properties of the carbonate and phosphate minerals and the presence of significant concentrations of dissolved species in the flotation pulp. In this paper, inorganic adsorption and surface transformation phenomena exhibited by the dolomite/apatite systems are examined in detail. Electrokinetic, adsorption, and flotation results indicate that when placed in a common solution, these two minerals interact significantly, with a corresponding strong influence on flotation using a physisorbed collector. Such behavior can have strong implications for flotation plant practice.

Jan 1, 1993

By J. D. Miller, C. L. Lin

A PC, image-based, on-line instrument for measuring coarse particle size on a conveyor belt is under development. The hardware and software required to implement such a system are discussed, including the interface for the special image-acquisition hardware. The system concept is given with examples to illustrate the step-by-step procedure for the implementation of image-processing algorithms.

Jan 1, 1994

By Stuart K. Nicol, Malcolm D. Engel, Neville T. Moxon

Ion flotatir,n of gold is a process being developed to selectively float extremely dilute aurocyanide liquors using a novel surface active complexing agent. The principle of ion flotation is also applicable to a wide range of other metal-containing solutions. The market potential of the gold flotation process would be enhanced by the possible combination of the gold recovery capabilities with both cyanide recovery and metal removal. For example, recovery of copper cyanides from a return liquid strean1 would be a useful means of reducing operating costs and satisfying environmental pressures to treat tailings dams. Experimental work is described where samples of tailings solution from a far north Queensland gold mine were subjected to ion flotation to remove copper cyanide species from a clear recycle solution. The form in which these products was removed was of secondary importance compared to the need to produce a clean solution for use in the plant. Recovery of the anionic copper cyanide species was accomplished using a quaternary ammonium surfactant.

Jan 1, 1991

One of the core tenets of Sustainable Development is transparency and information sharing, i.e., government and corporate reporting. Governments report on issues within their sphere of responsibility to the degree that their constituents demand that they do so. Firms undertake reporting for two reasons: they are required to do so by law, and doing so makes good business sense. In recent years, stakeholders have come to see themselves as having a right to information about government actions and business operations that have the potential to affect their lives, health, community and environment. As a result, disparate groups, including industry associations, non-profit groups, academics, and individual firms, attempted to lay out what governments and firms should report. There are many types of sustainability reporting. In this paper we focus on three of them that both governments and firms utilize. We discuss the benefits of each. We argue that while the goal of complete and perfect data is not achievable or feasible, sustainability reporting of all three types is necessary to ensure that sound public and private decisions are made.

Jan 1, 2007

By Alan E. Isaacson

Extensive gravel deposits exist within a six-county area in the mountains surrounding the Salt Lake Valley, and in the mountain ranges to the west. The six-county area includes Davis, Salt Lake, Summit, Tooele, Utah, and Wasatch Counties. The majority of these are beach deposits from prehistoric Lake Bonneville. However, real estate development associated with a projected population increase of 54 percent over the next 20 years is expected to remove most gravel deposits in Salt Lake County from consideration for mining, forcing gravel operations to relocate from eastern Salt Lake Valley to the Oquirrh and Stansbury Mountains farther west. The gravels in these ranges are of lower quality and require additional processing to manufacture asphalt and concrete. Replacing gravel resources along the Wasatch Front with resources in the Oquirrh and Stansbury Mountains over the next 20 years has the potential to increase construction costs by nearly $1 billion. The majority of this cost (82 percent) is the result of increased transportation costs due to longer distances to market. The remainder of the cost is attributable to lower quality gravels that will require additional processing in the manufacture of asphalt and concrete. The following analysis and discussion does not take into consideration the amount of crushed stone that is currently being used in the construction industry in northern Utah, its use as a substitute for lower quality gravels, or as a factor in the base case projection.

Jan 1, 2001

By S. C. Schmelter

The destabilizing effect of water pressure on rock mass stability is examined quantitatively by the finite element method. A coupled code that accounts for the simultaneous effects of rock mass deformation and transient fluid flow is used for this purpose. The traditional soil mechanics assumption of an incompressible fluid is shown to be untenable for the analysis of porous, fractured rock slopes. A Mandel-Cryer effect, a transitory but elevated and potentially destabilizing water pressure following a cut, was not observed.

Jan 1, 1997

By J. Bilant, J. Donnelly

"A spatially-discretized heap leach simulation model was developed within the GoldSimTM modeling framework for the Coeur Rochester Mine, Nevada. The model is being evaluated by Rochester as a means of improving forecasting of silver and gold production on an actively loaded valley fill heap leach facility. Optimization of future heap leach operations and crusher product size is also being evaluated with this software. Simulation modeling incorporates metallurgical data such as mine planning, particle size distribution of placed ore, stacking plans, pad geometry, and leaching dynamics. The heap leach model is represented as a discretized matrix with lifts providing vertical separation to form 19,840 spatially discrete cells. Each cell is quantified with regard to ore properties and metal content. The model tracks solution and cyanide-complexed silver and gold within each cell as a function of time based on pad operations, unsaturated flow properties, and kinetic rates. Practical heap leach management and daily operation will be discussed as it relates to the simulation and forecasting model. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities, is an open-pit silver and gold mine located in Pershing County, Nevada. In 2015 Rochester produced approximately 4.6M troy oz silver (Ag) and 52K troy oz gold (Au) through combined cyanide heap leaching of the Stage II, III and IV heap leach pads with recovery via a Merrill Crowe process plant. Rochester is actively stacking and leaching ore on the Stage III Heap Leach Pad. The Stage III pad contains approximately 70M tons of ore in a valley fill configuration and is forecasted to receive an additional 20M tons of ore by the life-of-pad in 2019. The ultimate height of the pad is permitted to be 400 ft above the liner and solution collection system. Approximately 80 percent of the ore loaded on the Stage III pad is produced from tertiary crushing split from two crushing circuits that produce a nominal 80 percent passing 3/8” product. The remaining material consists of run-of-mine (ROM) from off loads of re-mined waste rock stockpiles. Metallurgical testing of the ore indicates low variability in geologic properties and high variability of both Ag and Au extraction rates for the various particle size distributions. Historically the valley fill configuration provided metal forecasting challenges that could not be predicted as the leach pads grew. Forecasting metal production and leach optimization of the Stage III pad became challenging due to the extreme variation in heap leach pad depth, application of available barren leach solution and the variability of Ag and Au extraction rates for the various ore particle size distributions. To assist with understanding and optimizing metal production forecasting with these factors for the Stage III pad, Hatch developed a spatially-discretized heap leach simulation model using GoldsimTM dynamic simulation software. The model incorporates metallurgical data such as mine planning (tonnages and grade), particle size distribution, ore crushing, ore stacking plan, pad geometry, and both leaching dynamics and kinetics to forecast metal production from a consolidated mine plan."

Jan 1, 2017

By V. I. Ryaboy, V. A. Luknitsky, V. V. Zuyev

The action has been studied of three types of reagents used as intensifiers in grinding copper-molybdenum, sulphide-sheelite, polymetallic and other types of ores, namely N-donor, dispersant, and surface-acting agents. It has been proved that, depending on the type of ore treated, the C (N-donor) and C-170 (dispersant) reagents increase the yield of the principal size fraction of 0.074mm by 8-16% (relative). Consequently, the specific mill capacity improves by 13-21 %. The C and C-170 reagents activate the subsequent flotation stage and are thus beneficial to the mineral recovery. The surface-acting reagents affect the mineral grinding process to a lesser extent. The intensifying action of the reagents is attributed to the effective crushing energy decrease (lower crack-resistance factor) or else to the slime-dispersing effect of the reagents. The pilot-plant test results for the C reagents are given. Both C and C170 reagents are commercially produced and recommended for use at a number of concentrators in Russia, Uzbekistan and Kazakhstan.

Jan 1, 1995

By K. Norrena, E. Magri

An important problem in mine operations is the classification of material as waste, low-grade stockpile and ore. This classification must often be made with blasthole data that are widely spaced and that have sampling errors. Geostatistical-simulation techniques combined with basic economic principles allow a procedure for classification that maximizes the expected profit. Geostatistical-simulation methods (Gaussian, indicator or annealing-based) allow the integration of hard and soft data in the creation of alternative, equally probable realizations of the mineral grades. At each location, for each realization one calculates the "profit" if the block were to be classified as ore or waste. The optimal classification is the one that maximizes expected profit (a maximum profit selec¬tion or MPS procedure). In this paper, the authors discuss the theoretical justification of the method and implementation details. The use of blasthole data from different types of mineral deposits, that is, different levels of continuity, are considered. The authors also show the efficacy of the procedure with different levels of sampling error. The increased revenue due to the MPS procedure and improved sampling is shown. The paper shows the geostatistical-simulation procedure and the uncertainty in block grades that result from incomplete and imperfect sampling. The optimal classification is presented. Optimal block classifications are transferred to realizable dig limits by hand-drawing polygonal boundaries. The results of the proposed method are compared to classification based on kriging. Limitations and areas of future work are identified.

Jan 1, 2000

By Jozef S. Stachulak, Bruce R. Conard

INTRODUCTION The concern of occupational exposure to diesel exhaust pollutants is an important workplace issue for the mining industry. During the last three decades of diesel operations at Inco, a significant amount of research and improvement has been made in the area of work environment, and effective diesel operation. This paper will review the experience gained by Inco's Ontario Division from the implementation and the use of modern engines, improved fuel quality, and the exhaust control technology, coupled with adherence to proper maintenance and ventilation design and practices. Past monitoring practices and the current occupational monitoring program at lnco are outlined. A major new research initiative involving multi-stake holders in diesel performance is described. MINING IN THE SUDBURY AREA The discovery of nickel-copper ore in the Sudbury area dates back to the year 1856. The existence of this orebody was noticed when a strong compass deflection was observed by a provincial surveyor. This discovery, even though documented in official re- ports, failed to arouse any public attention at that time. In 1884, a rock-cut was blasted through a small hill near the village of Sudbury to permit laying track for the Canadian Pacific Railway (Boldt 1967). The rock-cut uncovered a body of massive sulfides with a copper content of over nine percent. The mineralization is concentrated along the outer margin of the Sudbury Basin, an oval-shaped structure having a dimension of 55 x 95 kilometres. The ore extends down-dip to to at least 3000 metres below the surface. The mining methods at lnco can be divided into two categories: "filled-stope" and 'bulk" mining. This division, in the broad sense, may also reflect the environmental conditions of the mine. In the past, the selection of a mining method was based on the size, shape, grade and the strength of the ore and its surroundings. The recent development of improved technology and mining equipment permitted wider application of low cost bulk mining methods. UNDERGROUND DIESEL EQUIPMENT The first diesel-powered machine, a 145-horsepower scooptram, was put into operation in March 1966, in a cut-and-fill stoping complex at Frood Mine. The number of diesel machines underground in the Inco, Ontario Division, mines was increased to 360 units by 1971,550 in 1977 (Rutherford 1978), and over 830 diesel-powered units in 1995. The following list indicates current mobile diesel equipment. LHD 194 Loaders 81 Trucks 28 Jumbo Drills 78 Personnel Carrier 101 Service Equipment 155 Locomotives 50 Bolters 30 Scissor Lift 113 About 20 percent of the LHD and truck units are equipped with electronic fuel controlled engines. COMPOSITION OF DIESEL EXHAUST Diesel exhaust contains hundreds of pollutants (Watts 19921, including components of unburned fuel and lubricating oil and products of incomplete combustion of the fuel and oil. These pollutants are emitted either as gases or as particles. Gaseous pollutants include carbon monoxide, nitrogen oxides, and sulfur ox- ides, as well as a variety of organic compounds, such as hydro- carbons, aldehydes, and polynuclear aromatic hydrocarbons. The particle phase, also known as diesel particulate matter (DPM), is the filterable portion of diesel exhaust. Figure 1 depicts the trimodal particle size distribution that arises from different mechanisms of aerosol generation (Cantrell and Rubow 1992). Primary combustion aerosols, including diesel exhaust aerosol, are formed as very small particles (in the 0.001 to 0.08 micrometre range), but physical mechanisms such as condensation and coagulation quickly transfer the aerosol mass from the nuclei mode to the accumulation mode. These processes result in a mass median diameter of approximately 0.2 micrometres for diesel particulate matter, and 90% of the particles are less than 1.0 micrometre in size. These particles have a high surface area, permitting the adsorption of different substances produced during combustion. Mechanically generated aerosols, on the other hand, typically contain particles greater than 1 micrometre in diameter. The particle phases of diesel exhaust contain three components (Bagley, et al, 1996) shown by Figure 2, namely: a carbon- aceous fraction composed mainly of solid-carbon particles, a sulfate fraction containing small hydrated sulfate particles, and a soluble fraction that contains compounds that are soluble in organic solvents and are adsorbed or condensed onto carbon core particles. These compounds consist primarily of higher molecular weight hydrocarbons and PAH's and may contribute 15% to 45% of the weight of the total particulate matter (Schuetzle, 1983). The control of these pollutants is necessary to ensure a healthy work environment. Proper engine maintenance, engine design modifications, improved fuel quality, and use of exhaust control technology, coupled with good ventilation practices, all

Jan 1, 1997

By Tetsuji Hirato, A. J. Monhemius, Yasuhiro Awakura, G. W. Warren, E. Peters

An electrostatic pseudo-liquid membrane technique, in which extraction and stripping take place simultaneously in a single reaction vessel using an electrostatic dispersion, was applied to recover Ni(II) from aqueous 0.1 kg m-3 Ni(II)(as NiSO4) – CH3COONa solutions, and the Ni(II) ions were concentrated by a factor of 9 into an aqueous 1.0 kmol m-3 HCI solution using D2EHPA as an extractant at the applied voltage of 3.7 kV for the dispersion. When the process of ESPLIM proceeds favorably, the concentration of Ni(II) in the upper part of the organic phase of the reaction vessel is lower than that in the lower part. In addition, the concentration of Ni(II) in the organic phase of the extraction chamber is higher than that in the stripping chamber. For the stable operation of this process, the stripping rate must be greater than the extraction rate to prevent the excess accumulation of Ni(II) in the organic phase which leads to the poor dispersion of the aqueous phase.

Jan 1, 1993

By R. Frenette, A. W. Mo, H. A. Hamza

Fine particles present major technical and economic problems to those who deal with solid/liquid separation processes. In the coal industry the problem is compounded by the large amounts of produced fines such as those present in Western Canadian coals. Flocculants in the form of high molecular weight water soluble polymers are commonly considered an effective solution for the enhancement of the separation process. These reagents are relatively expensive especially when considering a low-price commodity such as coal. Optimization of the use of these reagents is therefore an operational necessity. Six polymers were evaluated as to their effectiveness in flocculating a fine coal tailing. Results were compared with those for a reference flocculant, in-use at that time in the washery. It was shown that, in general, flocculants significantly improve the solid/liquid separation process. The ranking of the flocculants as to their effectiveness in settling and filtration indicated that the best flocculants for settling were not necessarily the most effective for filtration. Flocculants that showed the best filtration improvement were generally cationic and those best for settling were anionic.

Jan 1, 1988

By F. M. Swain

High-calcium limestones occur in the upper part of the New Market Formation, of Lower Middle Ordovician age, in Franklin and Cumberland Counties, Pennsylvania. The high-calcium facies of the New Market Formation is represented by sublithographic limestone or vaughanite, which probably formed in quiet water; low-energy environments such as intershoal lagoons, or in protected bays similar to the present-day Florida Bay environment. Rapid facies changes are characteristic of the strata. The better grade of stone lies in the upper 100 to 125 feet of the New Market Formation and averages 95-97% calcium carbonate. Silica and magnesia are about equal in amount as impurities. One high-calcium belt extends from the Maryland state line through Chambersburg and Newville to beyond Carlisle. The strata in this belt are structurally complex, which requires careful field study' and core-drilling prior to exploitation. Stone suitable for blast-furnace flux is present in relatively large amounts, but stone for open-hearth use or portland cement requires more selective quarrying.

Jan 1, 1966

By Leo Misagi

THE ROLE OF MANAGEMENT IN PLANT SAFETY Safe Production In plant management, safe production is an ideal. It becomes reality when: 1. Plant employees work in healthful and safe conditions. 2. Plant safety is in harmony with productivity. 3. Worker absenteeism and turnover are low-the work force is stable. Plant management must apply its talents, skills, and resources to build and maintain the foundations of safe production on a system of policies, procedures, and attitudes. It must do so by marshaling all managerial functions - staffing, direction, control, innovation, and representation-toward that goal. Ideally, a plant safety program is proactive. Management should plan and implement safety activities that are aimed at prevention. Past accidents-accomplished facts-should not be the sole guide of future actions. In other words, positive preventive measures, not the fewness of accidents are the criteria for safety production. An ideal safety program is one which is cost effective. Management should view plant safety as part of a broader program-loss control. Loss control includes prevention of fires and other accidents, unhealthful conditions, and occurrences that cause bodily injury, illness, property loss, or damage. Management evaluates the employees' productivity and safety. An effective training program aimed at loss control is the hallmark of safe production. Ideally, both labor and management should be well versed in safety. They believe in the premise that work-related injury and illness, as well as property loss and damage from fire and other accidents, are manageable and preventable. Such belief prompts them to learn more about the work process and potential hazards associated with each job. They also learn how to expect and prevent fues and other accidents, and respond to emergencies at the plant. Plant management determines which individuals or groups of employees are accountable for the following functions:

Jan 1, 1991

By Eugene F. Casey, William H. Hansmire, J. Ghaboussi, Randall L. Lentell, Harvey W. Parker

INTRODUCTION Construction of a major intercepting sewer in Brooklyn, New York involved tunneling in soil over several subway lines. In two instances the clearance between the subway and sewer was sufficiently close that concern was raised about the influence of the new construction. Prior to each critical crossing, analytical studies were performed which characterized the tunneling influence. It was demonstrated that with adjustments in construction procedures the crossings could be made without affecting the integrity of the subway linings. A comprehensive program of instrumentation and full-time monitoring was undertaken to ensure that any unforeseen adverse developments during crossing would be recognized. The successful crossings were subsequently made with minimal influence. Reported herein are the special construction conditions for the two crossings, the analytical simulation of behavior, and the results of monitoring on the subway linings. SEWER TUNNEL CONSTRUCTION AND EXISTING SUBWAYS The Red Hook Intercepting Sewer is a 2600 m (8600 ft) long tunnel which is part of a major water pollution control project in New York City. For clarity of nomenclature, the sewer is termed a 'tunnel' while the rapid transit structures are termed 'subways'. For routine construction, the tunnel was mined by hand with a 3.2 m (10 ft-5 in.)

Jan 1, 1981

By S. A. Elmquist

Research activities performed by Cleveland-Cliffs Research and Hibbing Taconite plant personnel during the last decade have resulted in the development of an improved autogenous mill grinding circuit. Minus one (1) inch autogenous mill trommel oversize material, con-sidered to be a critical size, is magnetically cobbed and then crushed to 100% minus 3/8" prior to reentry into the feed end of the mill. Autogenous mill capacity increases, up to 25%, have been measured in pilot plant tests using this approach and are also anticipated for the Hibbing Taconite concentrator which presently has reached a 15.5% improvement.

Jan 1, 1994

By Huaiyu Liu, Shan Liu, Dashang Chang, Maixi Lu, Yaqun He, Yali Kuang

The expert system for coal preparation plant design mainly solves the crux--separation flowsheet design and optimization of product structure. There are twelve basic flowsheets available in the system which are representative of financial plants. The system can select better flowsheets automatically according to the property of feed and scale of plant. Then, it can choose the best flowsheet and product model from the better flowsheets through analysis and optimum calculation. The expert system is made up in Turbo Pascal 6.0 and consists of three sub-systems: Lump and grain coal system, coal slimes processing system, and raw coal system. Several representation methods, such as production rule, procedure, and object-oriented programming, are used to express the expert's knowledge in the system. To decide the optimum product structure, Zangwill's method is used to make an advance product model. The expert system has the performance of interpretation strategy, by 'tracer" technology and pre-arrangement text, and of learning new expert's knowledge.

Jan 1, 1996