Search Documents

By Charles J. Johnson

The United States is totally dependent on imports for all primary chromite and most ferrochrome supplies. Although the United States imports chromite and ferrochrome from a number of countries, the long-term future of chromite supplies appears to lie in southern Africa (Republic of South Africa and Zimbabwe) where 88 percent of known world reserves exist. Floreover, low mining costs and the availability of low-cost electricity for ferrochrome production gives South Africa a comparative advantage over most other chromite and ferrochrome-producing nations. A well-known problem faced by the United States is that when viewed from a longer-term perspective, the major sources of supply of metallurgical grade chromite and ferrochrome may be subject to disruption. The three countries that have caused the greatest concern have been the Republic of South Africa, the Soviet Union, and Zimbabwe. South Africa presents a particularly difficult problem because it may be subject to internal political unrest and/or U. N, economic sanctions. South Africa has increased its share of world chromium production from about 30 percent in 1968 to 62 percent in 1978.1

Jan 1, 1982

By William J. Maloney

Blind drilled shafts are becoming increasingly popular as a secondary and sometimes primary means of ventilation. This is particularly true in the Appalachian coalfields. Some reasons for the rebirth of blind shafts are economics, timeliness, safety characteristics and their inherent independence from underground operations. Blind drilling has had limited use in hard rock and tunneling ventilation. Advances in cutters, bit design, equipment and lining systems have made blind drilled shafts the shaft construction technique of choice for ventilation specialists. History of blind drilling Blind drilling's roots include the Nevada test site, the coalfields of Appalachia and Germany, and the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin. Shafts completed by oilfield equipment ranged from the shallow 1.5 and 1.8 m (5 and 6 ft) lined shafts on the Nevada test site to two 3 m (10 ft) lined, 222 m (730 ft) deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths. The record, completed in 1969, is a 2.28-m-diam (90-in.-diam), 1875-m (6150-ft) deep shaft, located in the Aleutian Islands of Alaska.

Jan 1, 1993

By D. R. Spears, D. A. Stanley

The US Bureau of Mines investigated the fundamental aspects of shear-flocculation using a rapid, in-situ particle size analyzer. Silica was stirred in the presence of an aliphatic amine to determine the effects of collector coverage, stirring speed and solids concentration on the kinetics of shear-flocculation. The results showed that shear flocculation is a two-stage process. In the first stage, which occurs during the first 1-2 min. of the reaction, the mean particle size increases rapidly, and in the second stage, an equilibrium is set up between the rates of floc growth and floc decay. Collector dosage affected the position of the equilibrium by altering the number of surface sites for particle-particle attachment. A minimum stirring speed was necessary for shear flocculation, which was dependent on solids concentration and collector dosage. This stirring speed was the minimum necessary for particles to overcome the electrostatic energy barrier, and that results in keeping the conditioned particles dispersed. Larger particles flocculated more rapidly. At very high stirring speeds, large flocs became unstable, resulting in a narrowed particle size distribution in the slurry.

Jan 1, 1995

By Terry Ritzel

Predictive maintenance technologies include vibration analysis, tribology, infrared thermography, ultrasonic detection and electrical measurements. These technologies have been applied to large electric mining shovels at the Cyprus Sierrita Mine outside of Tucson, AZ. The predictive maintenance program was initiated on the P&H models 2300 and 4100 electric shovels during August 1996. Results of these technologies have shown the potential for improving electric min- ing shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition-based planning of component replacement. Maintenance costs are minimized by focusing resources through condition-based prioritization.

Jan 1, 1997

By Harry M. Conger

Good afternoon, fellow members of the international mining community. I appreciate the opportunity to participate in this special three-day, international gathering, and to join with you in honoring one of my very good friends, Doug Fuerstenau. It couldn't be more fitting to have this kind of event to mark Doug's 60th birthday. You know, in addition to his faculty position at the University of California in Berkeley, Doug is a member of the Board of Directors of our Homestake Mining Company. So it is a double pleasure for me to help pay tribute to one of the outstanding academicians of the mining industry as well as a man with whom I work closely in running Homestake. I have been asked to talk about "The Future of Precious Metals," but I will concentrate my remarks on gold. Since the theme of this Symposium is "Challenges in Mineral Processing," what I'm going to talk about is a challenge that relates especially to a major problem faced by those of us who process ores to recover gold. I noted that in the Scope of this Symposium, it stated: "the mineral industry is currently facing many challenges to improve the economics, operating efficiencies and environmental concerns of the mineral processing system." I couldn't agree more with that statement. I think that a need exists for us to address this situation as it involves gold. And who better to consider this than the worldwide leaders of mineral processing research here assembled. I start with the premise that we need a new method for cyanide use or a chemical to replace sodium cyanide entirely. In the case of using cyanide differently, I see a continuing difficulty in getting general public acceptance regardless of how

Jan 1, 1989

By Yu Qixiang, Wu Yanyun, Guo Junfeng

The experience of mining coal and gas outburstprone coal seams shows that the degree of outburst danger in various coal seams and even at different parts of the same seam are quite different, and that to deal with them respectively in different ways will not noly be significant to safety but bring us remarkable economical profit, Based on the statistical data,including elght static and dynamic factors, gathered from coal and gas outburst spots at Nantong colliery in Chong Qing district of China, this paper has partitioned the degree of outburst danger of the No. 5 seam there by means of Fuzzy Clustering method. Because in the evaluation multiple indices have been considered, the result of partitioning is identical to practice and more efficient in applications.

Jan 1, 1991

By R. D. H. Bedd

GEOLOGICAL NOTES The area under discussion is situated approximately 150 m north of Loraine No. 3 shaft at ± 1500 m below surface. The block being mined extends from about halfway between 50 and 52 levels to just below 48 level (see Fig. 1). The EB reefs form the lower portion of the EB zone of the Elsburg series and in the 81 line area the various conglomerate bands show the best development. Up to 18 separate reef bands are developed and the distance from the bottom conglomerate band to the top is ± 26 m. The thickness of the quartzite which forms the middling between the various reef bands varies from 0.1 to 2 m. The strike is roughly north-¬south. The reef bands are payable individually. However, owing to the steepness of the reefs and their close prox¬imity, conventional mining would prove very difficult. The nonpayable reef bands all carry varying amounts of gold and the whole area is a massive payable reef body approximately 26 m wide and 60 m high at 300 to 400 m on strike. The major structure of the area consists of a north¬-south trending syncline. The western flank of the syncline has a steep easterly dip, in places approaching the vertical. This flank cuts out against the overlying rocks of the EA zone. The latter forms a noncon¬formity with the underlying EB zone. The eastern flank of the syncline dips to the west at an average dip of 0.17 rad (10°). The 0.1 rad (6°) north-plunging syncline was sub¬jected to severe faulting. The most important are the Nos. 4 and 10 faults, both of which have a roughly north-south strike. The No. 4 fault dips to the west at an angle of 1.04 rad (60°) with a downthrow of approximately 150 m to the west. The dip of the No. 10 fault is 0.69 to 0.81 rad (40° to 50°) west, with the western block having moved 150 m updip relative to the eastern block. The EB reefs are being mined by the sublevel stoping method down from the sub-outcrop position to the cutoff against the No. 4 fault. On the downthrow side of the No. 10 fault, that is just above the 54 level, two reef bands are payable and will be mined conven¬tionally. ROCK MECHANICS From the section in Fig. 1, it can be seen that the area under consideration is surrounded by stoped-out areas. This will naturally change the stress distribution extensively. The only way to calculate the stress field for such a geometry is to use the finite element method. It was established that this method worked for the present geometry and so the method was applied to predict the stress behavior of the final geometry. From the results, it appeared that the effect of the old stopes was to destress the area. There are, however, some areas-such as the 50 and 48 north footwall haulages-which will require continuous attention. In these two footwall haulages, deterioration can take place due to tensile stress which

Jan 1, 1982

By J. K. Neathery, T. X. Li, H. Ban, J. M. Stencel, X. K. Jiang

Upgrading molybdenite ore can be technically difficult and expensive if talc is a major impurity in the ore. The layered structure of molybdenite and talc decreases the surface specificity of floatation and suppression agents, thereby making molybdenite ore beneficiation inefficient if under some wet processing methods. However, oxidic talc surfaces may be distinct from the sulfidic or oxysulfidic molybdenite surfaces, such distinction related to electron work functions and/or densities of electron donors/acceptors sites. If such differences are present, the upgrading of finely sized molybdenite ore by dry triboelectrostatic methods may hold advantages over traditional wet methods. We report on the upgrading of molybdenite ore using a laboratory-scale, drytriboelectrostatic beneficiation system. This system employs pneumatic transport conditions to tribocharge, beneficiate and collect the fine molybdenite ore particles. Using this system, two Mo ores were beneficiated under dry conditions without the addition of water or surface modifiers and additives. Beneficiation performance was dependent on the particle size of the feed ore. The surface and particulate morphology and elemental concentrations in the parent feeds and the beneficiated products were examined by scanning electron microscopy (SEM) and optical microscopy. These data, in conjunction with a complete recovery analysis, define some potential advantages of dry, triboelectrostatic beneficiation processing and provide insight into factors controlling molybdenite ore upgrading.

Jan 1, 1999

By Hans Breuer

The new regulations for the bituminous coal mining industry, issued by the mining authorities of the Federal Republic of Germany, are aimed at reducing to a feasible minimum any development of the coal workers pneumoconiosis (CWP) by lowering the admissible dust exposure of mine workers. Additional and improved measures of dust suppression and job assignment control *) are required for the purpose In this connection two basically different demands are placed on dust measurements: As far as dust suppression is concerned, the causes of dust development and the effectiveness of methods applied to reduce dust concentrations have to be identified, whereas with regard to the control of job assignment, the dust exposure of mine workers has to be depermined. Demands placed on dust measurements -- specifically for determining dust exposure -- are liable to become more severe since the threshold limit values were considerably reduced in these last years and since any additional dust suppression measures as well as a purposeful job assignment to certain mine workers are dependent on relevant measuring data. Therefore, research work has been carried out with the objective of measuring and evaluating, in terms of their effect (i. e. their incidence on the development of a CWP), size distribution, concentration, and specific noxiousness of any prevailing dust conditions.

Jan 1, 1980

By C. A. Pickles, S. J. Splinter

Silicon oxynitride, Si2N20, has many of the intrinsic properties of a potential high temperature engineering ceramic material. Some of these properties are similar to those of silicon nitride, which has been more intensively studied. However, although silicon nitride ceramics are approaching a state of microstructural refinement for various engineering applications, silicon oxynitride has received little attention. This has been mainly due to a lack of an economical and reproducible method of producing pure crystalline Si2N2O. Several reports exist on the preparation of crystalline Si2N2O from SiO2 and Si3N4, yet very little kinetic data exist. Even less is known about the carbothermic reduction of SiO2 in a nitrogen atmosphere to produce Si2N2O. In this paper, a review of the properties and methods of preparing silicon oxynitride will be presented. In addition, results obtained by reactively sintering SiO2 and Si3N4 will be discussed. The overall reaction is as follows:

Jan 1, 1990

By J. J. Krizek, A. H. Ditto

INTRODUCTION The Carr Fork property is situated in the Bingham Mining District located on the east slope of the Oquirrh Mountain range in Utah. The mine is adjacent to and lies west of Kennecott's Bingham Pit some 25 miles southwest of Salt Lake City. The Bingham Mining District contains one of the largest copper reserves on North America. Mineralization is associated with the Bingham stock which intruded through some 16,000 feet of sedimentary formations. Mineralization and a1teration zoning was developed radially from the Bingham stock with lower grade disseminated copper mineralization centrally located in the stock and adjoining quartzites. In addition, several garnetized limestone beds abutting the stock were also well mineralized. These skarns will be Carr Fork's initial mining target. Of the several limestone beds, only two, the Yampa and the Highland Boy have significant commercial interest at present. These beds which are 50 feet to 150 feet thick and are separated by 200 to 400 feet of quartzite were highly folded, thrusted and faulted, resulting in a dip variance from 20" to vertical. The predominant dip, however, is between 20" and 45" from horizontal. Quartzites surrounding the limestone beds were subjected to the same degree of tectonic activity with resultant intense fracturing and stress relief. The limestone beds which have a higher elastic modulus and which also experienced fracture healing during mineralization appear to have greater competency and strength than the quartzites. Four shafts nominally 3500 feet deep will provide access to the mine which will be a highly mechanized trackless operation, designed to produce 14,000 tons per hoisting day. First production is scheduled for the last quarter of 1979.

Jan 1, 1977

By Ted D. Johnson

INTRODUCTION The tailing dam is part of the SOHIO L-Bar Uranium Mine and Mill located about 70.8 kilometers (44 miles) west of Albuquerque in northwestern New Mexico. The dam location is shown on Figure 1. The tailing dam is one of the last upstream method dams permitted in the industry. Design and construction aspects of the project, as well as operation and maintenance considerations, are reviewed herein. Since initial construction, SOHIO Western Mining Company and Woodward-Clyde Consultants have developed several modifications and improvements in the dam's operating and monitoring procedures. This work has been done in coordination with the New Mexico State Engineer's Office and in accordance with recommendations in a report done for the Corps of Engineer's Phase I Dam Inspection Report. Modifications and improvements described should be of particular interest to owners and operators of other tailing dams utilizing the upstream method of deposition. The tailing facility was designed for a 10-year life to provide an ultimate storage capacity of 6 1/2 billion kilograms (7 1/2 million short tons) in an area of about 180 acres. A plan view of the tailing dam is shown on Figure 2. The tailing consists of approximately 75% sand size material and 25% fines (material passing the No. 200 sieve). The tailing dam includes a small earth starter dam with raises of the dam accomplished using tailing deposited by upstream method techniques. The starter dam is a homogeneous embankment about 610 meters (2000 feet) long, a maximum height of 12 meters (40 feet) and 2 1/2:1 (horizontal to vertical) upstream and downstream slopes. The starter dam contains an internal drainage system which includes a near vertical chimney drain connected to horizontal finger drains. A typical section through the maximum height of the starter dam is shown on Figure 3. A small confining dam, approximately 1.6 meters (5 feet) high, is constructed beyond the limits

Jan 1, 1980

By Richard M. Crowell, John W. Shield, Todd J. Harvey

Facing lower gold prices, gold mine operators throughout the world are seeking ways to reduce costs for treating refractory sulfide ores. Many gold mines, currently producing oxide ores, have underlying refractory sulfide deposits and the operators could extend the mine life by processing these sulfides. Fortunately, oxidation technologies for refractory ores need not be complex nor costly. GeoBiotics, Inc. has developed heap biooxidation technologies (GEOCOAT™) for treatment of refractory gold ores and concentrates. GEOCOATTM uses simple low cost unit operations common to heap leaching of gold and copper ores. The cost effectiveness and flexibility of GEOCOAT™ heap biooxidation allows mining companies to expand operations to include refract01y ore. In addition, GEOCOAT™ can be utilized to supplement or replace existing oxidation processes such as roasting, autoclaving, or agitated tank biooxidation, and to treat a lower resource grade than is currently economic. The GEOCOAT™ technology involves coating sulfide concentrates onto sized support rocks and biooxidizing the sulfides in a heap configuration. After biooxidation the concentrate is stripped from the support rock, neutralized and leached in conventional cyanidation facilities. Ashanti Goldfields Company Ltd. (AGC) produces over 885,000 ounces of gold per year from oxide and refractory ores at its Obuasi operations in Ghana. Refractory flotation concentrates are treated in roasters and in the world's largest stirred tank biooxidation facility. In August 1998, AGC and GeoBiotics jointly constructed and operated a field demonstration heap of the GEOCOATTM process at the Obuasi operations. The heap contained I 082 tonnes of support rock and 125 tonnes of concentrate. The heap was approximately 19 meters square at the base and 3.8 meters high, and ran for 88 days after which the concentrate was reclaimed. Average gold recovery after biooxidation was 91.5% with a NaCN consumption of 8.6 kg/t. Baseline gold recovery by direct cyanidation of the concentrate was 53.8%.

Jan 1, 1999

By R. K. Rajamani

The theoretical model based on fluid mechanics, in conjunction with the laser-Doppler velocimetry (LDV) measurements, elucidate the size-classification mechanisms in an industrial hydrocyclone. The model has no adjustable parameters and involves solving the Navier-Stokes equations to predict the liquid-phase velocities. The spatial-concentration gradients were determined considering the particle phase in the Lagrangian frame and the classification curve was determined by balancing the forces acting on the particle. The force balance requires liquid velocities, which in turn depend on the local volumetric concentration of the particles. Hence, complete modeling work involves coupling both the concentration and liquid-phase velocity calculations until convergence is reached. Finally, the experimental and predicted classification curves were presented for 250-mm hydrocyclone operating at high-percent solids.

Jan 1, 1994

By A. J. Richardson

Before the development of the underground stoping and mining costs can be considered, certain facts about the ore body, the proposed mine, markets, etc., must be known or determined. In the case to be studied, the zinc-lead mineralization occurred with a narrow vertically dipping structure of undetermined length and vertical extent. Exploration completed to date has revealed 6.5 mil¬lion st t of proven reserves. A further 820,000 st of in¬dicated reserves has been outlined and this tonnage is considered capable of being expanded by a factor of approximately four after more detailed drilling. After studying the market conditions and completing a very preliminary feasibility study, it was decided that production would be 730,000 stpy (or 2000 stpd) of ore. First year production would be at the rate of 1500 stpd. The main design criteria for the selection of the min¬ing methods are minimizing surface subsidence, maxi¬mum recovery of the ore body, maximum degree of grade control, maximum productivity, and safe working conditions. Two basic extraction systems are considered capable of meeting these requirements: mechanized cut¬and-fill stoping and sublevel long-hole stoping with filling. The primary development system of the mine has been designed to give maximum flexibility in stoping systems and layout and to permit changes if considered necessary as a consequence of actual production ex¬perience. At the present time, access to the mine is by a circu¬lar concrete lined vertical shaft, 16 ft diam, sunk to a depth of 1380 ft. Two exploration levels have been driven within the ore zone at depths of 165 and 1246 ft below the surface outcrop. The development to date had the objective of sampling the mineralization and produc¬ing detailed information on the outline of the ore body and the distribution and controls of zinc and lead values. In an attempt to satisfy the basic design criteria for the mine, it was decided that production would be best achieved by a combination of 40% sublevel long-hole stoping and 60% cut-and-fill mining. Costs of exploration and capital development of per¬manent underground facilities are normally written off over the life of a mine. Production expenditures, on the other hand, are of a temporary nature and are normally charged as and when incurred as an operating expense. Reasonably accurate predictions of mine production costs can be built up from engineering design and estimates of individual mine activities for ultimate inclusion in the comprehen¬sive data required for financial decision making. The simulated operations can be costed on a detailed basis in the form of a monthly operating budget. The budget format can be generalized or detailed, depending upon the scope of the project. However, ex¬perience suggests that a fairly detailed format has the advantage of assuring that all significant cost items are included. For underground costing it is suggested that the budget structure include five major cost centers (i.e. development, diamond drilling, ore extraction, hoisting/ transportation, and general mine expense). These in turn are detailed under numerous subheadings. The mechanism for compiling an operating budget will be illustrated. Because of its relative simplicity, ore extraction under sublevel long-hole stoping has been chosen for illustration. All other activities, simple or complex, can be estimated in similar fashion. BLOCK AND STOPE DEVELOPMENT Long-hole blocks, used where advantageous, will be up to 250 ft in height, depending upon the vertical con¬tinuity of the mineralization, and approximately 300 ft long. Drawpoints will be at 36-ft intervals and serviced by loading crosscuts driven from a footwall drift parallel to and close to the ore zone. Pillars between the stopes will be 50 ft wide. Stopes will be drilled off with vertical rings of blastholes drilled from sublevels approximately 60 ft apart vertically. This drilling will be done by percussion drilling machines (31/2 in.) mounted on a trackless drilling rig. Load¬haul-dump (LHD) equipment will be used to move broken ore from the drawpoints to the orepass connecting to rail haulage systems. On completion, long-hole stopes will be backfilled to prevent caving and to facili¬tate later pillar removal. From a planned stope layout, a forecast of produc¬tion and development is made in Table 1. Table 1. Block Tonnage and Stope Development Quantity Ore Waste Total ore block 375,000 st 2 stopes 310,000 st 1 pillar 65,000 st Access crosscuts, 4 at 100 ft 400 ft Drill sublevel drifts, 6 at 300 ft 1800 ft Stope raises, 3 at 250 ft 750 ft Undercut sublevel drifts, 2 at 300 ft 600 ft Loadout crosscuts at 35-ft intervals 550 ft 100 ft 3300 ft 500 ft Total development footage 3800 ft Tons per ft of development 987 st

Jan 1, 1982

By Z. T. Bieniawsk, C. A. F. F. Santos

The effects of artificial weathering on the mechanical properties of the Loyalhanna sandstone have been investigated. Weathering was simulated in the laboratory by subjecting cylin- drical specimens of rock to alternate cycles of wetting and drying (in distilled water at 2O0C 2 5OC and in an electric oven at 105OC t 1°C, respectively). The total number of cycles was 100 and the geomechanical characteristics of the altered material were determined through uniaxial compressive and indirect tensile ("Brazilian") tests, with the determination of axial and trans- verse strains and monitoring of acoustic emission activity (rate and total event count). Moisture content and weight loss data were collected after each cycle and the mechanical parameters (unconfined strength, indirect tensile strength, young's modulus, Poisson's ratio, permanent set and AE/MS activity) were determined for unweathered specimens and after 10, 20, 50 and 100 cycles of wetting and drying. Hypotheses for the effect of weathering on the geomechanical properties of the Loyalhanna sandstone are proposed as reinforced by petrographic analyses carried out for the different stages of artificial weathering. A methodology for assessing the degree of physical weathering of rocks is proposed based on the number of wetting and drying cycles.

Jan 1, 1986

The 2014 George A. Fox Conference at the Graduate Center, City University of New York in New York City was presented under the theme, ?21st Century Challenges for the Tunneling Industry. Bruce Grewcock, chief executive officer and president of Peter Kiewit Sons? Inc., opened the conference with a keynote address in which he set the tone for the rest of the day by touching on the many challenges the industry is facing, which are plentiful and complex. Covering the breadth of the industry, he spoke about everything from the technical challenges that come from working beneath the streets of some of the most densely populated regions in the world to the challenges that come from working with the people who live in those areas. ?My observation is that we, as an industry, are being asked to put structures in places where they are needed, but are complex environments to work in,? said Grewcock. ?We work in an industry that relies on some of the most technically challenging engineering in the world, and when we are done with a project, we cover it up and no one ever sees it.? Despite these issues, Grewcock said that, in his opinion, the biggest challenge the industry is facing is that of people; more precisely, where to find the next batch of people. Looking out at the conference-record crowd of more than 400 registered attendees, Grewcock quipped that he saw plenty of gray beards and asked aloud, ?Where will we find, educate and train the people to tackle the issues that this industry will face in the future??

Mar 1, 2014

By G. H. Kuhnhausen

The Bear Creek Uranium Mill was designed in 1975 to process 909 tonnes per day (1000 STPD) of low-grade uranium ore from the Powder River Basin in Wyoming. The mill was expanded to 1818 tonnes per day (2000 STPD) in 1979. The Bear Creek Uranium Project is owned by the Bear Creek Uranium Company, a partnership of Rocky Mountain Energy Company and Mono Power Company. The original mill design contemplated processing ores from Bear Creek Uranium Company properties exclusively. The expanded capacity has been utilized for tolling ores from Kerr McGee Nuclear Corp. and other mining companies in the region. This paper describes the process of designing the original mill, the lessons learned from operation, and the design of the process modifications required for expansion. The project background, design philosophy, design basis, design criteria, actual flowsheet, special design considerations, and a comparison of assumed operating conditions and actual operating results will be presented. Bear Creek Uranium Company wishes to thank and acknowledge the help granted by the many operating companies who provided invaluable information, insight, and critique of the Bear Creek design through all the various stages and were instrumental in the successful completion and start-up of the mill. Without their contributions, the design philosophy used at Bear Creek would not have been possible and the results obtained would surely have been less satisfactory.

Jan 1, 1979

By A. M. Alfantazi, R. R. Moskalyk

Over the years, improvements have been made in the recovery of nonferrous metals, including improvements in the areas of mineral processing, pyrometallurgy and hydrometallurgy to extract cobalt as a byproduct from host minerals containing mainly nickel, copper and associated precious metals. At present, the technological emphasis is on solvent extraction coupled with electrowinning (SX-EW) for lateritic sources of supply within the Southern Hemisphere, such as in Australia and New Caledonia. Although sulfide-bearing ores, such as those found in Canada and Russia, will serve as a viable long-term source for cobalt, a ubiquitous metal, the future trend is anticipated to be in the implementation of compact and efficient SX-EW facilities that apply state-of-the -art innovation with environmental compliance This paper serves to collate the known practices for the recovery of market-grade cobalt by means of electrowinning from either an aqueous sulfate medium or chloride medium after upstream leaching, solvent-extraction and solution-purification procedures. For completeness, other commercial production techniques for the recovery of cobalt as a sulfide or oxide product are included in the summary of current cobalt processing practices.

Jan 1, 2000

By Thomas D. Kaufmann

The 1982 recession set the US mining and metals industries reeling. Will the oncoming recession of 1991 hit as hard? Probably not, thanks to a shallower downturn, a weaker dollar and remarkable lower costs. Effects of the last recession That the 1982 recession was traumatic to the American mining and metals industry is an understatement. Quantities of metals consumed dropped. Metals prices fell despite continuing general inflation. The resulting real gross revenues of producers of each of the major metals plunged, in the trough of 1982, to levels one-fourth to two-thirds of those of the peak of 1979 (Table 1). By contrast, most industries in the United States were not hit anywhere nearly as hard. Real GNP, the aggregate of all production, slipped only 1 % from 1979 to 1982. Metals are most sensitive to the business cycle because of their applications. All metals but gold are raw materials to downstream industries. Raw materials are victims of strong fluctuations. This is because buying industries try to hold high inventories in boom periods when goods are in short supply. They reduce inventory levels in buyers markets when suppliers have idle capacity and raw materials are in ample supply.

Jan 1, 1990