Search Documents

By N. R. Sainath

This paper discusses a laboratory investigation that studied the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 40- and 100-mm-diam (1.5- and 4-in.-diam) cores were first mapped by visual inspection. The permeability of cores to water-stressed in a triaxial stress field representative of in situ conditions - was estimated. The samples were then exposed to 20g/L (2.7 oz/gal) sulfuric acid and the experiment was repeated. The porosity and the rate of recovery of copper from the specimen during leaching were also studied. The measured permeability of unleached samples with no visible fractures ranged from 10-16 to 10-19 m2 and it increased as leaching progressed. The porosity increased significantly with leaching, while the rate of copper recovery decreased.

Jan 1, 1994

By M. S. Klima, B. K. Kim

The use of a 25.4-mm- (1-in.-) diam water-only hydro-cyclone for separating liberated 125 x 25- µm high-density particles from similar-size lower-density (2.65 g/cc quartz particles, as might be used in soil washing applications, was investigated. As expected, cyclone performance was greatly affected by changes in cyclone geometry and operating conditions. A single-stage separation recovered 75% of the magnetite (4.8 g/cc) while rejecting nearly 60% of the quartz. With ferrosilicon (7.0 g/cc) as the heavy component, the recovery improved to 85%. The use of dense medium in a single stage increased both ferrosilicon recovery and quartz rejection to approximately 90% each. In addition, computer simulations of a three-stage circuit were performed. The simulations showed that recoveries approaching 97% with quartz rejections of 95% were possible.

Jan 1, 1999

By Dae S. Young, Steven F. Hoerger

The geostatistical method of indicator kriging (IK) was extended to analyze two-dimensional distributions of rock joint orientations. The IK method provides a non-parametric approach for spatial analysis of local probability distribu- tions. By taking into account the spatial correlation of rock joint outcomes and the relative geometry between estimation unit and samples, the IK method provides optimum, spatially conditioned estimates. The estimation method was tested by comparing distributions of actual mapped rock joint orientations with their corresponding kriged estimates. The comparisons show the unbiasedness and accuracy of the non-parametric approach for estimating local probability distributions.

Jan 1, 1986

By Wang Yingmin, Xu Zhuyun

The optimum of general mine ventilation networks is very difficult and has a considerable significance. Based on the content model, this paper presents a more general nonlinear programming model whose number of variables equals that of independent meshes. The constrained conditions are linear inequalities only. The model is changed into an unconstrained problem with multiper method. The optimum results are computed with DFP algorithm and the Improved Golden section method is used in its linear searching. The computer program written in Quick BASIC is suitable to the optimum of any type of large mine ventilation networks with different regulating devices. The paper presents two examples for optimum of ventilation networks.

Jan 1, 1991

By B. Amadei, A. Squassabia

This paper introduces the Rock Mass Median (RMM) index, a statistical measure of the mechanical quality of a rock mass thus is obtained through a mechanistic interpretation of the Poisson stochastic process. This process is the theoretical foundation of the Exponential Model, a probability distribution successfully used in practice to describe the spacing of discontinuities in rocks. Building on the Exponential Model, a simple method to compute RMM based on a widely accepted mechanical quality index is also presented. Verification is per formed through the analysis of two sets of core samples. Hypothesis testing at the 5% level of significance supports the validity of RMM for these samples.

Jan 1, 1994

By Vernon F. Swanson

The expansion of a fluidized bed of carbon depends on fluid velocity, fluid temperature (viscosity) and particle size of the carbon. This paper presents a mathematical model which can be used to calculate the necessary fluid velocity. It will allow the design of sufficient freeboard in the column to accommodate expected operating conditions. Although this paper is keyed towards the use of activated carbon in precious metals adsorbtion from water solutions, the model is.valid with any fluid. Additionally, the method of calculating the required suspension velocity in CIL or CIP pulps is described.

Jan 1, 1992

By M. Girardeau, J. Blondin, M. Nomine

It is well known that surface moisture and fine content have a strong influence on coal handle- ability. It is known as well that these two criteria are not sufficient to classify coals. It seems that certain types of coals are intrinsically difficult to handle, the reason being still not well understood. For these coals, moisture and fine content are aggravating factors and have to be strictly controlled in order to avoid handling problems (sticking, arching in hoppers.. .). CERCHAR has undertaken research aimed at identifying the role of intrinsic characteristics of coal with regard to handling properties. Two of them have been identified as particularly relevant : the clay content and the "colloidal particle" content. Two simple tests commonly used for soils characterisation, but never used so far for coal, have been applied to characterise a wide range of coals. The derived classification has been compared with an empirical classification based on dry screening tests. DRY SCREENING EXPERIMENTS Dry screening at a relatively low screen aperture (e.g. 6 mm) may be considered as a good tool for assessing the handleability of wet fine coals. Difficult to handle coals always lead to rapid plugging of the screen whilst easy to handle coals can be screened without difficulties. A wide range of coals has been selected with various ash, moisture and fine content. Their characteristics are given in table 1. The experimental set-up consists of a 2 t.p.h vibrating screen equipped with two automatic re- cording balances collecting respectively oversize and undersize material. Provided that the feeding rate is accurately controlled, good reproducibility in the percentage passing as a function of time is obtained. Figure 1 gives examples of different types of relations that were obtained. - LMC coal exhibits a behaviour that is characteristic of easy to handle coals : % passing remains constant in the course of the screening operation. - B coal behaves slightly differently. One observe first a rapid decrease in the flow passing through the screen and then a stabilization. Hand- ling properties can be considered as intermediately - The curve relative to LHB coal is characteristic of a very difficult to handle coal that blinds the screen almost immediately. It is necessary to point out the fact that the classification derived from screening experiments is a global one, including not only intrinsic factors but also external factors such as fines and moisture content. The role of surface moisture is in particular very important and variations in this parameter may upset the empirical classification

Jan 1, 1988

By Stephen LaBrooy, David Muir

Gold ores in the geologically more recent rocks are often associated with copper minerals which pose problems of high reagent consumption with conventional cyanidation practice. Many examples exist in northern Australia, Indonesia, Papua­New Guinea, Chile, and Brazil where, despite various treatment options (LaBrooy, 1992), the processing of oxide and transition ores is uneconomic either for copper or gold recovery. Hence, there is a need for a reagent which is selective for gold without leaching copper minerals. The ammonia-cyanide system appears to meet this criterion (Muir et al, 1989; LaBrooy et al, 1991; Costello et al, 1992; Hayes and Corrans, 1992) but it has proven difficult to optimise and apply to a variety of ores due to differences in the mineralogy and reactivity of ores and a lack of understanding of how the system works. Recent work on the mechanism, however, (Muir et al, 1993) has thrown a new light on the problem which should allow better process control. Ammonia­cyanide mixtures behave neither like free cyanide nor free ammonia and too much of either reagent in the mixture is detrimental. The key to the process is understanding how ammonia enhances gold extraction yet inhibits copper extraction in an essentially cyanide environment.

Jan 1, 1993

By A. J. Hendron, G. Mesri, R. M. Semple

Squeezing ground conditions in hard-rock tunneling are associated with fault zones containing brecciated rock and gouge. Gouge is a stiff clay-like soil that exhibits a propensity to creep. The ground loads applied to tunnel supports in squeezing ground are known to be significantly time dependent. Accordingly, an experimental and analytical study is presented that deals with soil creep and its application to the prediction of tunnel support requirements in squeezing ground conditions. Relatively undisturbed samples of fault gouge obtained from Straight Creek tunnel in Colorado and Pacheco tunnel in California are classified as very stiff to hard clays of low plasticity. Constant-load undrained triaxial compression tests are performed on these materials. A simple, three-parameter creep equation is developed that adequately describes the observed deformation of fault gouge with respect to applied stress and time. The equation is shown to fit existing creep data of various soil types. The creep equation is used to modify an existing continuum-mechanics solution to the time-dependent behavior of unlined and lined cylindrical openings in a creepsensitive medium under a hydrostatic state of stress. Assuming properties for the medium that are representative of the fault gouge materials tested, parameter studies are performed for unsupported and supported tunnels in squeezing ground. The analyses permit estimates to be made of the steel set supports required for tunnels at different depths in various squeezing ground conditions.

Jan 1, 1974

By Robert F. Baker

Neanderthal technology is a harsh and inaccurate way to describe modern underground construction and mining practices, but such an exaggeration helps to focus on a major problem or wasted opportunity of modern society. Why is it not safer to excavate in the underground? Why are the working conditions still so unfavorable? Why are urban freeways, shopping malls, warehouses, power plants, sewage disposal treatment plants, and similar facilities still constructed on the surface of the ground--because it is a better location? On the contrary, if underground technology made full use of existing knowledge, underground resources and space would be much more effectively used. And why is the technology so inadequate? Certainly, researchers and practitioners are aware of the shortcomings and are equally aware of problems that have to be overcome. One of the most important reasons has to do with the type of policy goals that society has set in the past. Policy makers may have agreed that improvements would be desirable but no serious commitments have been made--that is, there has been no major allocation of resources to advance these technologies. And yet, to bring about significant changes will require significant time and resources. The resources that are needed are far in excess of what industry can afford to invest, particularly since the pay-off may be far in the future. So the problem reverts to society in general. As long as society is willing to tolerate the present costs and safety requirements for recovering minerals and for constructing underground facilities, then the changes will be slow in coming. Until such time as society sees and desires the benefits

Jan 1, 1974

By Thomas Oberndorfer

Recent publications indicate that there is a rising interest in the field of mining method selection, and increasing efforts are being undertaken to develop satisfying solutions. Yet, computer assistance for mining method selection (MMS), or in other, terms assistance in the (pre-)feasibility state of a project, still lags behind the computer application in other mining activities. This is true for research as well as for application. This paper is intended as a contribution to the development in computer-assisted mining method selection, and focuses especially on underground hard-rock mining. It is structured in four main parts. The first deals with general aspects of mining method. selection within the process of mine planning, and with problems and requirements which derive from this specific situation. In the second part some numerical MMS-approaches hitherto published are briefly introduced, and investigations on these approaches are discussed. Based on .these experiences, in the third part an analysis of the complex system MMS is presented. It focuses on heuristics, influencing factors, objectives, assessment-routines and mining methods, and emphasizes the essential necessity of a profound mining method description (MMD) specially developed for the requirements of MMS and numerical processing. Accordingly the fourth part of this paper presents a mining method description model developed at the Department of Mining Engineering, Montan-University Leoben (MUL), Austria. It describes the consequences of the investigation, in particular the new mining method description model, on 'the design of a MMS-system. The paper closes with a outlook on the possibilities of an successful MMS-system being realised.

Jan 1, 1992

By James C. Puckett

The mining industry finds itself in the middle, between the need to increase production of our energy resources and the necessity of minimizing the environmental impact. Using the recent past as a guide, the mine planning engineer's function will continue to increase as further coal quality constraints are made upon the production staff. The engineer will need to make use of all available tools in order to provide timely answers to the complex "what if" questions that arise. This need to consider many alternatives is bringing about a rapidly increasing acceptance and utilization of the computer. In the areas of data handling, mineralization modeling, and production simulation, the computer is an effective tool for the mine planning engineer. Described herein is a coal data storage and analysis system developed to provide timely answers to the "what if" questions for an operating strip coal mine in Montana. The characteristics of a computerized coal data base and coal quality planning system are outlined in this chapter. The system has been developed for use at a particular coal mine; however, it has applicability to coal mines in general. Fig. 1 is a flow chart showing the functional relationships of the system. There are three main file types: the drill-hole data base, the boundary file, and the zone file. The purposes for which each file is organized are illustrated on the flow chart.

Jan 1, 1979

By H. E. Rojas, G. T. Adel

The primary objective of most comminution operations is liberation; however, mill performance is generally quantified in terms of particle size. Only recently has the use of image analysis equipment made it possible to quantify mill performance on the basis of liberation. In this investigation, a series of tests were carried out to study the effect of mill operating parameters on the liberation of sphalerite from a sphalerite/dolomite ore. The parameters studied included mill rotational speed, mill loading and ball size. The results of this work appear to indicate that sphalerite liberation is improved under conditions that promote impact breakage, while dolomite breakage is enhanced under attrition conditions.

Jan 1, 1992

By J. B. Hiskey, S. Chander, B. J. Scheiner

The use of selected iron complexing agents in preventing or ameliorating acid mine drainage was investigated. The experiments were conducted in weathering columns using refuse samples from a coal cleaning plant. It was observed that the treatment with iron complexing agents significantly altered the rate of oxidation. Some of the reagents tested reduced the rate of oxidation whereas the others even enhanced it. The results showed that a commercial reagent containing oleyl imidazoline was most effective in retarding the oxidation rate. In addition, a simple treatment with this reagent substantially decreased the rate of oxidation of pyrite in a column that was generating acid at a high rate. The effect of this reagent on the surface properties of pyrite was studied by cyclic voltammetry and zeta potential measurements. The decrease in the rate of oxidation resulted from suppression of both anodic and cathodic reactions at the surface of pyrite.

Jan 1, 1993

By Franc Runovc

The service hoisting plant in the mining transportation is an installation serving for the vertical transport of material and persons. An adequate mathematical model is presented for simple evaluation of the project parameters where different plant designs and the ways of transport are take into consideration. The technical and economical optimization procedure is added to the basic mathematical model of the project. This approach enables on one hand the optimization of the reconstruction of the multi-purpose hoisting plants in order to suppress possible bottle necks, while on the other hand it enables the determination of such values of the parameters of the choice and of the operation that the sum of total expenses per a transport unit' becomes the lowest. The optimization procedure is designed in such a way that all numerical data of the optimum hoisting plant are printed out together with the graphical representation of dependencies of the fundamental parameters in broader optimization region.

Jan 1, 1992

By G. S. Austin, L. A. Brandvold, J. Renault

A series of tests were run on soil samples collected near the site of a Socorro, NM lead smelter that was abandoned more than 98 years ago. Three 30.5- x 30.5-m (100-X 100-ft) squares provided 13 samples each. As described in Part I (this issue), each sample was divided into seven splits according to particle size. A mineralogical examination of the fine-size fraction of Pb-contaminated soils failed to reveal crystalline Pb compounds. These authors conclude that Pb is present as amorphous phases or is adsorbed on the surfaces of soil particles. Site vegetation contained elevated Pb levels that increased with increasing Pb amounts in the soil. However, the biological absorption coefficient (BAC) indicates that some of the site's Pb is unavailable, or the plants are able to limit their uptake. Of the vegetation tested, rabbit bush showed the greatest increase of Pb levels in its roots, whereas levels in creosote were highest in the foliage. In cactus, the Pb levels varied. The amount of Pb due to dust incorporated in plant tissue is almost negligible compared to the amount absorbed through the plant vascular system.

Jan 1, 1994

By Dianne M. Satalic, Peter A. Spencer

Bacterial leaching is a mature technology and has been applied in six commercial plants with others in the design stage or under construction. Bacterial oxidation is a relatively inexpensive process which uses naturally occurring soil bacteria to assist in extraction of base and precious metals. Bacterial oxidation has ini­tially been applied for gold recovery but the technology is now being transferred to base metal leaching with processes already developed for copper, cobalt and nickel. Bacterial oxidation plants often have capital and operating cost advantages over competing technologies and do not need a highly skilled workforce. The most common species found in the conditions used for bacterial oxidation and bacterial leaching are Thiobacillus fer­rooxidans and Thiobacillus thiooxidans. One common species other than Thiobaci!lus found in the commercial bacterial leach cultures is Leptospirillum ferrooxidans. Mixed cultures of the three species named here have formed the basis of the technolo­gy applied in most of the commercial applications of bacterial leaching to date. These bacterial species already mentioned all belong in the classification of mesophiles and have an operating range from 20 to 43°C. One other culture, a moderate thermophile operating over the range 40 to 50°C, has been used in one commercial plant in Western Australia. Bacterial oxidation takes place in acidic solutions under aer­obic conditions. The oxidation reaction normally produces iron (II) in solution which is ultimately conve1ted into the iron (III) form. The pH value falls naturally as the sulphide minerals are oxidised and the starting pH value can fall as low as pH 0.6 as the oxidation reaction proceeds. This paper examines the impact of the technology selection and its application on the design, engineering and operation of a bacterial oxidation plant. The effect of the changes to these para­meters on the cost of the bacterial oxidation plant is discussed.

Jan 1, 1998

Up to the middle of 19 14, when I had reached what seemed like the advanced age of 30, I had enjoyed far more than my share of success and a lot of minor adventure. But the exciting experiences in distant lands that Soldiers of Fortune had made me long for had not yet materialized. And I had not accomplished the two goals that Mrs. Hughes' geography class at Belmont had set up for me. They were to see In its tropical home the enormous yellow bill of the toucan bird and to ride on a straw "bolsa" on Lake Titicaca. These aims were gratified In the next five years that were the epitome of "romance" in its German connotation of facts seen through the rosy glasses of imagination. Dr. Louis Ricketts was to a large extent responsible for my opportunity. I had been lucky enough to do a lot of work for and with the Doctor, as he was affectionately called by the mining men of the southwest. My association was in connection with his work with John Greenway on the complex metallurgical problems at Ajo. Soon after the Ajo investigation Ricketts had been made chief consultant for the Anaconda Copper Co. When Anaconda decided to undertake a cam- paign of exploration of the west coast of South America Dr. Ricketts thought of me and arranged with Greenway to give me a leave of absence from my Calumet and Arizona job. It took three days in New York in June 1914 to arrange the expedition. Ben Thayer, executive vice president of Anaconda, did most of the planning and I was to report to him. T.H. France, a 45-year-old mining engineer who had been driven out of Mexico by the Madera Revolution, was to accompany and help me. He spoke excellent Spanish and his years of Mexican experience had taught him how to get along with Latin Americans. He went ahead to Bolivia, our first target, to get an idea of the country and the problems. This was lucky as I hardly knew where Bolivia was.

Jan 1, 1976

By Walter Shukin, Mark T. Olsen

An enormous quantity of tailings to be ultimately stored, unfavorable topography, severe climatic conditions, and an environmentally offensive red effluent all contributed to the challenge of designing an effective and cost efficient tailings confinement program at the open-pit iron ore mine operated by Quebec Cartier Mining Co. at Mount Wright in northeastern Quebec. The mine has been operating since 1976, but a detailed disposal plan was first initiated with construction of some channels and ditches during 1980. In the coming years, a system of dams, channels, and tailings confinement dikes will be constructed to accommodate tailings produced in the next 25 years. Careful consideration has been given to environmental effects, and the works under construction have been sized and situated to be extended as required to an ultimate mine life of 87 years.

Jan 8, 1981

By R. D. Doepker, P. L. Drake

The dissolution of metals from various metal- mine tailings has been studied through a series of submerged tailings batch tests at US Bureau of Mines laboratories. Tailings selected for this study included both reactive (as determined by column leaching studies) and benign tailings. Metal mobilization in aerated (97% saturated with oxygen) samples appeared to be consistently greater than metal dissolution from stagnant (79% or 70% saturated with oxygen) waters. In the early weeks of the study, sulfate concentrations increased with solid-liquid contact time, while calcium dissolution remained early constant. Metal concentrations varied in relation to solid-liquid contact time and aeration. Leachate pH appeared to be nearly independent of solid-liquid contact time for basic tailings. Reactive tailings having both a submerged and a surface component demonstrated increased metal mobility.

Jan 1, 1991