Search Documents

By C. Zhou, C. C. Jobes, J. H. DuCarme

"Magnetic proximity detection systems (PDSs) are used with continuous mining machines (CMMs) to protect miners from striking and pinning accidents. Generators are used in a PDS to create magnetic fields covering the space around a CMM. The PDS determines the proximity of a miner relative to the CMM based on the magnetic flux density detected by a miner-wearable component (MWC) and simultaneously alerts the miner and stops the motion of the CMM if the miner is within a proximity that creates a striking hazard. A stable magnetic field is essential to the accuracy of the proximity calculations performed by the PDS. This paper presents the results of a systematic study of the magnetic influence of two types of steel structures found near a CMM—the body of the CMM itself and the wire mesh used for roof and rib control. The results show that the steel of the CMM body can change the magnetic field distribution and also alter electrical parameters of a PDS by changing its generator current. The study also shows that, depending on the distance between the wire mesh and a generator, the magnetic field can also be altered. INTRODUCTION Continuous mining machines (CMMs) can be up to 10 m (33’) in length and more than 3 m (10’) in width. These machines perform the coal cutting operations in underground room-and-pillar coal mines. Accidents during CMM operation accounts for an average of 250 injuries every year, and 43 miners have been killed by striking or pinning accidents involving CMMs in the United States from 1984 to 2015.Because of these fatalities and injuries, the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 that requires the use of proximity detection systems (PDSs) on all CMMs with the exception of full-face machines (Mine Safety and Health Administration, 2015). Currently, there are five different proximity detection systems that MSHA has approved as permissible for use in U.S. underground coal mines (Mine Safety and Health Administration, 2013). All of these PDSs rely on a miner-wearable component (MWC) to detect the generated magnetic fields that PDSs produce around a CMM (Schiffbauer, 2002). These systems use the magnetic field strength readings in terms of magnetic flux density from the MWC to determine whether a miner is at a safe distance from the CMM. A stable magnetic field is essential for the accuracy of a PDS."

Jan 1, 2018

By C. R. DeGennaro, M. R. Girman, J. Bickson, J. P. Homer, C. C. Jobes

Between 2005 and 2021, a NIOSH internal review showed that haul trucks were involved in 54 incidents at surface mines in the United States. Haul truck collision warning and avoidance systems (CXS) can assist in preventing accidents at surface mines. CXS use technologies to detect people or objects and alarm to alert haul truck operators. Robust testing can help ensure that they detect objects without excessive false positive alarms. Testing and validation would increase confidence in and encourage implementation of a CXS. Researchers from the National Institute for Occupational Safety and Health (NIOSH) reviewed documents related to the evaluation and validation of CXS with two objectives: (1) to identify methods and parameters used to evaluate detection performance and (2) to identify gaps in CXS test methods and in detection performance. Stakeholders can use the findings from this research to guide implementation of CXS to improve safety at surface mines.

Mar 2, 2022

By P. L. Dunn

Automatic control of fine coal cleaning circuits has traditionally been limited by a lack of sensors. Although several nuclear-based analyzers are available, none have seen widespread acceptance. In this investigation, image analysis is used for on-line determination of ash content in fine coal slurries. The ash content of a flotation tailings stream is correlated to the mean gray level of the slurry. Based on a 90% prediction interval, an analysis of sensor performance indicates an accuracy of 73 ± 4% ash over a range from 65-90% ash. While this result is comparable to existing nuclear-based analyzers, the video-based system is only a fraction of the cost. The sensor is currently installed at the Middle Fork preparation plant owned by Pittston Coal Company.

Jan 1, 1997

By R. L. Keiski, H. Miettunen

"The serpentinite massifs of Hitura are located in the municipality of Nivala in Central Finland. The most important sulfide minerals in the ore are pentlandite, pyrrhotite and chalcopyrite. The ore body consists of amphibolite rocks in contact with serpentinite against mica gneiss. The mean Ni grade of the ore is about 0.7%, and the highest Ni grades have been encountered in close contact. In general, the inner parts of the ore are strongly serpentinized ultramafite and some sulfides have been converted to mackinawite and valleriite. The degree of alteration varies considerably within the ore body and, correspondingly, the grain size of the sulfides varies as well. In this study, flotation tests were done with samples from different zones of the ore body. The flotation test results on the bench scale and plant scale are discussed in terms of the mineralogical features of the ore. Ores in the North Hitura zone differ from those in the South Hitura zone.IntroductionThe Hitura nickel mine, like the entire Nivala area, is part of the Bothnian Svecokarelian schist zone, where numerous Ni-Cu boulders have been discovered since the early 1930s. The Nivala area has therefore been the subject of exploration activities by the Geological Survey of Finland (GSF) and mining companies. The first period of exploration started in 1936, and the Makola nickel deposit, located 3 km south of the Hitura mine, was discovered by GSF in 1937. About 415,000 tonnes of ore were mined at Makola between 1941 and 1954. In 1937, during the exploration and development stage of the Makola mine, boulder tracing and a geophysical survey revealed a significant ultramafic body with some lowgrade Ni-Cu occurrences in the South Hitura zone.In 1961, GSF continued the exploration program in the area and discovered the North Hitura ultramafic complex and its allied Ni-Cu occurrences. In 1964, Outokumpu Oy bought the property and, after underground exploration, comprehensive mineralogical studies, process research and a feasibility study, production started in 1970 (Isohanni et al., 1985)."

Jan 1, 2015

By Gerald W. Elger

Research at the Albany Metallurgy Research Center has shown that high-purity rutile can be produced from relatively low-grade ilmenite obtained from a massive rock deposit. Ilmenite is first smelted in an electric-arc furnace to separate the iron and produce a slag enriched in titanium dioxide. Titania slag mixed with a phosphate flux is then oxidized to synthesize rutile and form a phosphate-glass matrix which contains the impurities. Attrition scrubbing the treated slag in dilute solutions of phosphoric or sulfuric acid liberates the rutile, which is concentrated by physical methods. Tests show that synthesized rutile containing 95 to 97 pct titania responds to chlorination at the same rate as natural rutile.

Jan 1, 1973

By Liming Yuan, Isaac Zlochower, RICHARD THOMAS, Thomas H. Dubaniewicz, Teresa Barone

Mining vehicle manufacturers are developing lithium-ion (Li-ion) battery electric vehicles as an alternative to diesel-powered vehicles. In gassy underground mines, explosion-proof (XP) enclosures are commonly used to enclose electrical ignition sources to prevent propagation of an internal methane (CH4) air explosion to a surrounding explosive atmosphere. Li-ion batteries can create pressurized explosions within sealed enclosures due to thermal runaway (TR). Researchers at the National Institute for Occupational Safety and Health (NIOSH) measured TR pressures of lithiumiron phosphate (LFP) cells as a function of free space within sealed enclosures and observed an inverse power relationship. A well-confined cell produced 294 bar (4260 psia) of pressure during a TR, far exceeding minimum pressure containment specifications for conventional XP enclosures. Results indicate that adding enough free space surrounding LFP cells can reduce TR pressures to levels below that expected for CH4-air ignitions. Measured TR temperatures were below the minimum autoignition temperature of CH4-air.

Nov 6, 2020

By Lianhui Jia, Yali Han

"The key technologies of a large rectangular pipe jacking machine with dimensions of 10.12m × 7.27m (width x height) include selection of rectangular cross-section cutting modes, analysis on the strength and stiffness of the rectangular shield, integrated control of electro-hydraulic proportional thrust systems and ground conditioning for excavation are presented in detail in this paper. These key technologies have been successfully applied and verified on site during tunneling, providing a new concept for the building of large rectangular traffic and pedestrian tunnels in urban areas for the future.1 INTRODUCTIONIn the past, underground tunnels were mainly used for drainage, sewage, utilities, metro tunnel, etc. and most of them had circular cross-sections. Recently, as a result of economic development, gradually accelerating urbanization process and diminishing ground space, underground tunnels have already become a new trend for urban underground space utilization. Due to the heavy traffic flow, the demands for rectangular cross-section underground tunnels, such as pedestrian underpass and road tunnel, are increasing gradually.The Rectangular pipe jacking machine (hereinafter referred to as RPJM) was firstly developed in Japan for the construction of metro station, pedestrian underpass, underwater tunnel by-passes, etc. Kazunaki Kawai et al. introduced a RPJM developed and manufactured by KOMATSU in 2002 [1]. Tosikazu Kubota et al. confirmed the rectangular tunnels’ superiority to circular tunnels with regard to larger inner cross-section and lower construction cost in their RPJM construction reports [2]. Compared to circular pipe jacking machines, a RPJM also has the merits of a higher inner tunnel space utilization ratio and is able to excavate in shallow overburden areas. As shown in Figure 1, the effective area of a rectangular tunnel is more than 20% higher than that of an equivalent circular tunnel."

Jan 1, 2016

By D. Men, R. Q. Honaker, J. C. Hower

"Maceral separation is one possible technique to expand coking coal resources, either by increasing the blending ratio of non- or slightly caking coal or rationally utilizing the coking coal according to the different behaviors of macerals in coking. The success of maceral enrichment for a given coal using flotation is dependent on the differences in flotation kinetic rate among macerals. This paper presents the flotation rates and zeta potentials of the vitrinite-rich and inertiniterich maceral concentrates obtained from six coal samples of different ranks – from high-volatile B bituminous coal with mean random vitrinite reflectance (Rrandom) of 0.64 percent to low-volatile bituminous coal with Rrandom of 1.73 percent – using a float-sink procedure. The flotation results show that vitrinite-rich concentrates can be produced in tap water using froth flotation only with frother for the high-volatile B and A bituminous coal samples, but there was no good performance for the high-volatile C bituminous and medium- to low-volatile bituminous coal samples. The zeta potential results show that froth flotation could probably separate the high-volatile C bituminous coal samples well by adjusting pH, but there was no good performance for the higher-rank coal samples. IntroductionMetallurgical coke is used in blast furnaces for steel production and is produced by the carbonization of coking coal. Because caking coals are rare and expensive, they are often blended with non- or slightly caking coals. Considering the tight supply-demand situation for coking coal in China, it is important and urgent to develop highly efficient technologies for rationally utilizing and expanding coking coal resources (Mochizuki et al., 2013)."

Jan 1, 2015

By P. Amelunxen

Over the past several years, the combination of higher energy and steel costs and the recent commercial deployment of high-pressure grinding rolls (HPGR) technology in hard rock mining have led many multinational mining companies to evaluate the suitability of HPGR technology for their particular comminution circuits. HPGR technology is perceived to require a higher capital investment while delivering lower long-term operating costs. This paper undertakes a critical evaluation of this perception. By evaluating the capital and life-of-mine operating costs of competing circuit designs for soft, medium and hard ores, the HPGR break-even point can be identified, at which the incremental capital cost of an HPGR circuit is equivalent to the net present value of the projected operating cost reductions. For ores with hardness parameters above the break-even point, HPGR circuits could offer economic benefits, while for softer ores, SAG mill/ball mill/pebble crushing (SABC) circuits are likely to be more economical and energy efficient. This evaluation considers both an SABC reference circuit and a traditional stage crushing configuration. Other influential factors are also discussed.

Jan 1, 2011

By LUIS ALBERTO TORRES-CRUZ

The assessment of liquefaction vulnerability is crucial to understanding the potential consequences of a tailings dam failure. The “Plewes method” is a relatively well-known and simple screening method to assess liquefaction potential based on results of cone penetration testing (CPT) which may be complemented with laboratory testing. The objective of the current work is to emphasise the screening nature of the method and its uncertainties when applied in tailings deposits. Specifically, the paper highlights the difficulties in assessing the intrinsic uncertainty of the method and the additional uncertainty that results from variations of the slope of the critical state line (λ10) along the depth of the CPT sounding. The results of the method are too uncertain for detailed characterisation of tailings even when a relatively low intrinsic uncertainty is assumed. However, the method characterises weaker soils with lower uncertainty (although still too high for detailed characterisation) than stronger soils. The uncertainty of the method is negatively affected by the relatively low λ10 values that are typical of nonplastic tailings. It is suggested that the results of the method should be presented in scatter plots in which the spread of the data is consistent with the uncertainty of the method.

Jan 28, 2021

By P. A. Korpi

In March of 1978 the first set of Angular Spiral Liners utilized in grate discharge ball mills for wet grinding was put into service in the San Flanuel Concentrator of Flagma Copper Company. The use of these liners has decreased grinding media consumption by 19.2% and grinding energy consumption by 15.8%. In addition a 1.1% increase in grinding throughput is being realized through the use of the system. This paper describes the Angular Spiral Lining System and reviews the test program at the San Manuel Arizona Concentrator. Operating parameters are discussed in addition to the current testing program to futher optimize the system.

Jan 1, 1982

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"The National Institute for Occupational Safety and Health (NIOSH) has been researching refuge alternatives (RAs) since 2007. Refuge alternatives typically have built-in pressure relief valves (PRVs) to prevent the unit from reaching unsafe pressures. The Mine Safety and Health Administration (MSHA) requires that the PRVs vent the chamber at a maximum pressure of 1.25 kPa (0.18 psi, 5.0 in. H2O), or as specified by the manufacturer. To facilitate PRV testing, an instrumented benchtop test fixture was developed using an off-the-shelf centrifugal blower and ductwork. Relief pressures and flow characteristics were measured for three units: a modified PVC check valve, an off-the-shelf brass/cast iron butterfly check valve, and a commercially available valve that was designed specifically for one manufacturer’s steel pre-fabricated RA and has been adapted for use in built-in-place (BIP) RAs located at one mine. PRVs used in tent style RAs were not investigated. The units were tested with different modifications and configurations in order to check compliance with 30 CFR regulations. BACKGROUND The Mine Improvement and New Emergency Response Act of 2006 (Miner Act) (1) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement. Section 13 of the MINER Act specifically directed the National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines, and the Department of Labor to act on the results of such research as appropriate. These mandates culminated in the 2009 adoption of changes to 30 CFR mining health and safety regulations, requiring underground coal mines to provide mine emergency RAs and associated components, to provide a life-sustaining environment for persons trapped underground. Such RAs can be either self-contained mobile units or built-in-place (BIP) facilities. The regulatory changes also include provisions establishing requirements for the Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One specific criterion for maintaining a safe RA atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (specified as 0.18 psi, or approximately 5.0 in H2O), or at a pressure as specified by the RA manufacturer, above mine atmospheric pressure in the RA (2)."

Jan 1, 2016

By J. Fisher, M. Barish

Over the past several years, Somerset International has successfully installed over 20 patented Sub325® Fine Coal Recovery Systems in the United States, Australia, Canada and Russia. These installations recover between 5 TPH and 40 TPH for the host sites. In addition to the increased revenue from the direct recovery of a recirculating load (Screen Bowl “Insurance”, Direct Recovery vs. Indirect Recovery via Recycle, CPSA 2020), host sites have seen benefits ranging from improved operation of refuse equipment to a reduction in the solids content of the refuse streams. As Somerset has improved ultra-fine coal recovery through the introduction of Sub325® Effluent Flotation and, most recently, the Sub325® Effluent Settler™, the amount of coal that has been recovered from these systems has increased by up to as much as 25%. Many host sites have taken a sense of ownership in the Somerset system and consider it to be a critical circuit in the overall optimal performance of the plant. In the past year, Somerset has taken the initiative to expand upon the capabilities of the Sub325® Fine Coal Recovery System, primarily the Sub325® Solid Bowl Centrifuge, to include Refuse Tailings Dewatering to allow for co-mingled refuse disposal. As slurry ponds and boreholes are becoming difficult to impossible to permit and operate, there is a need for a reliable, low-maintenance, continuous operation that can produce a handleable refuse cake. Refuse tailings disposal applications are by no means limited to coal plants and impoundments. Somerset has successfully tested at iron ore and phosphate locations throughout the world and have begun commercial installations. The ability to dewater -325 mesh material, whether it be coal, coal refuse, iron ore tailings, or something else, is a vital piece of processing capability for the continued production of mining operations across the globe. This paper highlights the success that Somerset has had in the coal industry worldwide as well as the initial successes with phosphate, iron ore, and copper tailings (patent pending).

Mar 2, 2022

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results from the investigation of the application of thermal fragmentation in Australian hard rock underground narrow-vein mining. Two geologically similar samples from an underground narrow-vein hard rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method. Particle size distribution showed a higher generation of fine product, − 2 mm, by thermal fragmentation compared with selective blasting by 31%. The Bond work index for thermal ore (12.62 kWh/t) is half to that of the blasted ore value (25.32 kWh/t). The average grindability obtained for the thermal ore sample was greater than the blasted sample by a factor of 2.44, a higher value indicating a decrease in the energy required to grind. The thermal fragmentation method generates product with higher dissolution of gold in cyanide, by 14% for the − 9.5 + 2 mm size fraction samples. Additionally, the thermal fragmentation results in higher production of − 9.5 + 2 mm material by 15 % compared with selective blasting.

By NARAYAN K. BHAGAT, ARVIND K. MISHRA, C. Sawmliana, Rakesh Kumar Singh, Panchanan Hembram

Mining operations in close proximity to dwellings and sensitive structures present challenges in terms of mitigating the undesirable effects of blasting while maintaining productivity and ensuring the safety of surrounding communities. This paper explores the application of advanced blasting techniques, including the use of electronic detonators and the splitting of total explosive charges, to address these challenges. A series of experimental blasts were conducted, comparing blasts conducted with and without splitting of holes, to assess the impact on ground vibrations. The results demonstrated significant reductions in vibration magnitudes when implementing controlled blasting practices with splitting techniques. The findings highlight the importance of total explosive charge in determining ground vibration magnitudes within the danger zone of mine workings. The use of electronic detonators provided precise control over blast sequencing, contributing to safer and more efficient mining practices. These advanced blasting methods offer a practical and innovative solution for conducting safe mining operations near dwellings and sensitive structures, ensuring compliance with safety regulations while sustaining productivity.

Jan 23, 2024

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results from the investigation of the application of thermal fragmentation in Australian hard rock underground narrow-vein mining. Two geologically similar samples from an underground narrow-vein hard rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method. Particle size distribution showed a higher generation of fine product, − 2 mm, by thermal fragmentation compared with selective blasting by 31%. The Bond work index for thermal ore (12.62 kWh/t) is half to that of the blasted ore value (25.32 kWh/t). The average grindability obtained for the thermal ore sample was greater than the blasted sample by a factor of 2.44, a higher value indicating a decrease in the energy required to grind. The thermal fragmentation method generates product with higher dissolution of gold in cyanide, by 14% for the − 9.5 + 2 mm size fraction samples. Additionally, the thermal fragmentation results in higher production of − 9.5 + 2 mm material by 15 % compared with selective blasting.

By David B. Crouch

Wastes in various forms have always been a part of mining, and management of mine waste has evolved from the early days of "push it over the side and down the creek" to today's highly engineered waste facilities. Changes have been brought about not only by technological advances in the ?3M?s? - mining, milling, and metallurgy - but also by environmental awareness and changing social values that have been manifested in an ever-growing maze of regulations. This is a dynamic era, and the debate goes on. So it is that planners have to anticipate permit and regulatory requirements in the site-selection process along with the traditional criteria. The McLaughlin gold project is an example of how one company, Homestake, has met this planning challenge. In August of 1980, Homestake Mining Company announced a major gold discovery in northern California known as the McLaughlin Project. The property is approximately 80 air miles northeast of San Francisco near the junction of Lake, Napa, and Yolo Counties. This is an area where mercury has been mined off and on for over 100 years; gold has never been mined in the area. The gold is microscopic and finely dispersed in a complex geologic setting. Reserves are estimated at approximately 20 million tons at a grade of approximately 0.16 ounces per ton.

Jan 1, 1983

"Tell us how you got involved in mining?I was first exposed to mining at a young age, as a consequence of my dad and his passion for the industry and rock collecting. Even though he graduated with a degree in mining engineering from Washington State University, my dad spent most of his career working as a structural engineer for the Boeing Company. At the time, Boeing supported a range of employee activities and clubs, including one devoted to mineral prospecting, small-scale dredging and rock hounding. My dad was extremely active in the Prospectors Club, where as a family, we spent a good part of my youth tramping around the Pacific Northwest digging for mineral specimens and panning for gemstones and gold. On my mother’s side of the family, I had relatives that mined in Dawson City and Fairbanks, AK which left a family legacy of sorts. I loved the stories that my dad and a close buddy of his, who was a geologist, would tell about various operations and towns, as well as the wild times at the annual Northwest Mining Association (NWMA) meeting in Spokane, WA. My first recollection of ever being at a commercial operation was during a tour of the Bunker Hill Mine with my dad when I was 7 or 8 years old; this had to have been shortly before the May 1972 fire at Sunshine. That visit of the mine and processing facilities made a permanent impression on me. While I always knew there was something special about the Silver Valley, I began to understand why. To this day, I still get the same feeling when I visit historic mining districts like Leadville, Morenci, Virginia City, Butte, Silverton and Barkerville. During our summer excursions to Helena, MT to dig sapphires, we would usually make visits to Butte and watch mine operations inside the Berkley Pit and surface activities at the Kelly and Mountain Con. In high school, I did well in math and science and began entertaining thoughts of pursuing a degree in engineering. Above all, I wanted to go to a college in the West that had a good academic reputation, where I could also play football. As a 6-ft, 190-lb nose guard, my options for a Division I scholarship were pretty slim, and there weren’t that many technical schools in the Northwest that were Division II that offered athletic scholarships. As fate would have it, I was unexpectedly contacted by Marv Kay, a legendary coach at the Colorado School of Mines (CSM), and was recruited to play ball. Fortunately, I had a couple of high school friends who were already attending CSM, and I had just secured a summer internship with Asamera Minerals in Wenatchee, WA. It was as if all the stars had aligned, and, with the support of my parents, I made the decision to attend Mines. Despite the stress of getting through CSM during a period when the mining industry was in freefall, it was a great decision to attend Mines, and I’m thankful for all the opportunities, friendships, and faculty mentoring I received as a student"

Mar 1, 2019

By Cary Hirner, Dan Lopez, Ross Webb, Stephen O’Connell

"Construction of the largest desalinization plant in the Americas has commenced in northern Chile. It is part of a several billion dollar expansion at a copper mine whose operations nearly stopped due to the challenge of securing a reliable source of water from the Pacific Ocean in a safe and environmentally sound manner. This paper discusses the risk management, design and construction of a quadruple chamber intake and outfall shaft, high capacity pump station, three 7m diameter vertically drilled marine shafts and three subsea tunnels constructed through challenging Andean hard-rock geology. The three 2.5m diameter subsea microtunnels are being mined with vertical curves through variable quality rock 30 meters beneath the ocean and retrieved in the wet from the 7m diameter marine shafts. INTRODUCTION AND BACKGROUND The battle for securing the rights to a constant water supply is a worldwide issue and nowhere is that more evident than the Atacama Desert of Chile, the world’s driest place with areas of the desert that have not seen rainfall in recorded history. The Atacama Desert also happens to be home to some of the world’s largest ore deposits which require huge amounts of water to extract and process. What available water there is comes from three main sources: deep seated wells, glacial water from the Andes Mountains, and desalinated water. Vying for water from wells and glacial streams and lakes are numerous agricultural and domestic facilities in the valleys surrounding the Atacama Desert. Environmental regulations and legal rulings have limited the amount of “natural” source water which can be used for mining purposes. Desalination plants are a known solution for combating water scarcity, albeit a costly one. The total estimated cost of constructing this desalination plant is over $3B USD, which will include a 2500lps capacity and an approximately 118km pipeline from the coast up to the mine located in the Andes. The overall scope of the project includes design, procurement, and construction packages for the 2500lps desalination plant including the seawater reverse osmosis plant, water conveyance to the mine, power transmission, the reservoir and the marine works package which forms the basis of this paper. Key components of the underground construction portion of the Marine Works are:"

Jan 1, 2016

By A. M. Gaudin

A new method of measuring the viscosity of unstable suspensions has been developed, using a Heinz viscometer. The technique was applied to kaolin-water suspensions. Spreads in viscosity with lime additive were measured.

Jan 1, 1962