Search Documents

By R. L. Beatty

The Bond International Gold (BIG) Colosseum Gold Mine was discovered in 1865, but no recorded production occurred until the 1930's, with production approximately 19k9 (615 oz) of gold. The mine was closed in 1942 as a non-essential industry during World War II. The property was acquired by Dallhold Resources in mid 1986. Construction of a 1.1 million Mt carbon-in-pulp, cyanide mill started in November, 1986, and was completed in September, 1987. Minable reserves are estimated to be 9,560,831Mt (10,539,000St), with an average grade of 2.1 g/Mt (0.062 oz/st). This paper describes a general view of process flow and plant equipment, as well as a look at the maintenance and operational problems encountered in the fist six months of operation.

Jan 1, 1989

By Garry G. Lowder

The regional geologic setting is essentially a volcanic island arc built upon an oceanic basement, consisting of basalt and minor pelagic sediments (the Tinombo Formation of Eocene - lower Miocene age. Trail et. al. 1974). -- An east-west chain of intermediate and acid calc-alkaline volcanoes (the Bilungala Volcanics) was built on the oceanic basement during the Miocene. The Bilungala Volcanics are flanked to the north largely by contemporaneous andesites and volcanoclastic sediments of the Dolokapa Formation. During middle to upper Miocene time the Bilungala Volcanics were invaded by large masses of predominantly dioritic intrusive rock and it is within one of these dioritic intrusive complexes, the Bone Diorite, that the cluster of porphyry copper systems occurs. Renewed volcanic activity in the Plio-Pleistocene produced acid pyroclastic rocks (the Pinogu Volcanicsi whose distribution is controlled by present-day topography. Structural trends, largely interpreted from SLR imagery, are pre- dominantly NW or NIWJ. The right-lateral Gorontalo Fault, which trends hW through the town of Gorontalo (Katili, 19691 is the most prominent structural feature. Many of the major structures in the Tapadaa district have similar orientations and may be sympathetically related to the Gorontalo Fault.

Jan 1, 1976

By Meng Li, Hao Nie, Weitian Ding, Mamdouh Omran, Ying Li, Yao Ge, Yaowei Yu, Abourehab Hammam, Lei Zan

This study examines the isothermal and non-isothermal reduction behaviors of iron ore compacts in a pure hydrogen atmosphere and compares the results obtained during the reduction process by CO. The different phases accompanying the reduction reactions were identified using X-ray diffraction (XRD) and its morphology was microscopically examined. In isothermal experiments, temperature plays a significant role in the reduction process. At any given temperature, the reduction rate during the initial stages is higher than that during the final stages. The reduction rate in H2 atmosphere was faster than in CO gas. The comparison of activation energy values suggested that reduction with H2 is more efficient thanwith CO. At the same temperature, the time required to achieve a certain degree of reduction was lower when using H2 gas than CO atmosphere. In non-isothermal tests, the heating rate has a significant effect on the reduction rate and reduction extent. At the same heating rate, the degree of reduction was higher in H2 atmosphere than in CO gas. Based on experimental data, the parameters of reaction kinetics were deduced by application of model-free and model-fitting methods. The reduction in H2 atmosphere was controlled by nucleation model (Avrami-Erofeev model), while the CO reduction reaction was controlled by gas diffusion.

Sep 29, 2020

By M. Kane, O&apos

BHP Iron Ore initiated research programs in January of 1995 to develop long term plans for decommissioning of the waste rock material at their Mt. Whaleback operation. More than 2 billion tonnes of waste rock were deposited during the past 30 years. Ultimately, the operators will deposit a total of approximately 5 billion tonnes in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semi-arid climate adjacent to Newman, Western Australia, approximately 1200km north-northeast of Perth, Western Australia. The primary research program includes the development of technology for the long term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion, and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. A laboratory program and the soil-atmosphere modelling completed to design the horizontal field test plots are described. The construction of the horizontal surface field test plots are discussed together with the field instruments installed to monitor performance. The key components of the instrumentation program are the design and installation of large scale field lysimeters to measure the unsaturated flow of moisture into the waste rock from the base of the cover layer. The cover system is designed to maximize infiltration during wet periods for subsequent evapo-transpiration while minimizing surface runoff. The result is a near zero net infiltration to the underlying waste material. A key feature of the design is the use of pit run waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long term performance.

Jan 1, 1998

Sphalerite is commonly floated in an alkaline environment and under such conditions the overall activation mechanism is obscured by the hydrolysis of Cu2+ and precipitation of Cu(OH)2. Electrokinetic and kinetic flotation tests show that the activation of sphalerite is a two-stage process; the activation products formed on the surface of sphalerite in near neutral and in alkaline solutions in the first rapid activation stage are "flotation-inactive". These layers, when formed in an alkaline solution, are unstable and are transformed into the "flotation-active" form in the second stage. However, the surface layers formed during activation in alkaline environment by copper in the presence of lead ions are very stable and even after a long conditioning time the flotation rate is not improved. Consequently, while both Cu2+ and Pb2+ activate sphalerite flotation, quite unpredictable effects may result when both are present in the solution.

Jan 1, 1997

By Jacques LeBel

After a brief definition of asbestos and a review of regulations, the elements of asbestos dust control are outlined for various asbestos manufacturing industries. To prevent the asbestos dust to become airborne, the general procedure is to control the dust at the source by enclosure and exhaustion. The asbestos dust is collected and removed from the air with bag filter collectors of high efficiency (better than 99%) to ensure that the air emitted to the general environment or returned to the workplace are below the existing asbestos emissions regulations. Dust control systems should be regularly inspected and serviced to maintain at all times the efficiency and reliability of the equipment. Other effective procedures for asbestos dust control are also considered.

Jan 1, 1984

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.

By Thomas A. Gray

The Dolph Mine fire site is located in Lackawanna County, PA, approximately three miles northeast of the city of Scranton. The fire was burning in both coal refuse (culm) and underground anthracite mine workings. It was reportedly begun by rubbish burning on top of a culm bank. A site investigation was completed in 2006 to define the extent of the fire and to recommend fire control measures. A cut off trench was selected as the principal control method. Plans and specifications were prepared in late 2006. The project was bid and a contractor selected in early 2007. The trench construction was completed in 2007. This paper describes the investigation and selection of the fire control method and discusses the trench construction.

Jan 1, 2009

By K. J. Stanaway

Environmental pressures on waste disposal are forcing pigment producers to use higher content TiO2 feedstocks with lower levels of trace elements. Despite this, 50% of the worlds TiO2 comes from ilmenite concentrates with only 37 -54 % TiO2 An industry growth rate of 25 % in the next ten years combined with trends to diminishing resources and lower grades for rutile (95 % TiO2) and leucoxenized ilmenite (55 to 90% TiO2) mean that unless new discoveries are made soon, the industry will become even more reliant on ilmenite. A hypothetical ideal feedstock is presented and strategies to obtain it are suggested. Reasons for some of the mineral specifications are given.

Jan 1, 1994

By Gary A. Nowlan

The Casa Grande West-Santa Cruz porphyry-¬copper deposit is in the Basin and Range physiographic province west of Casa Grande, Arizona (Fig. 1). The Casa Grande West portion of the deposit is controlled by Casa Grande Copper Company and the Santa Cruz portion by ASARCO. The deposit contains at least 350,000,000 metric tons of rock with greater than 1 percent Cu. The deposit is covered by at least 300 m of sediment, with no visible expression of the deposit at the land surface. The deposit is in an area of prime agricultural land that depends heavily upon well irrigation because of a hot and arid climate. Because of the deep sedimentary cover, the chance is extremely remote that the geochemistry of soil or stream sediment would reflect the deposit even if the land surface were not disturbed by many years of farming. Irrigation wells of the area generally bottom in the sedimentary cover. The purpose of the study is to see if the Casa Grande West-Santa Cruz deposit is geochemically reflected in ground waters over and near the deposit.

Jan 1, 1981

By D. J. Tooker

For the next few minutes, I will be discussing a product and category that many people laughed at for years. The product is cat box filiers or commonly referred to by the brand name KITTY LITTER. This product was introduced in 1947 by Ed Lowe using the name KITTY LITTER. From 1947 to 1964 the product was sold mainly through pet shops. Starting in 1964, the grocery trade began to carry cat litters. From that point, the cate gory began a solid growth trend. Particularly in the '7O's, cat litter has experienced the same kind of explosive growth that has characterized the entire pet market. For example, in the twelve months ending 9/21/79, cat litter unit volume grew by 15% versus the previous twelve months. The basis for this explosive growth is easy to comprehend. The cat population itself is rapidly expanding, reflecting the changing life- styles of Americans. As famiiies grow smaller, there is room for a pet. As apartment and con dominim living shrinks living space, a cat fills the human need for animal companionship more efficiently. Table I illustrates current cat litter market factors and projects major trends into the future to conclude that the cat litter market will equal $205MM in 1985. With this dynamic growth defined, it was imperative that a company such as Lowe's that was totally devoted to the commodity-priced products, evaluate the opportunities for added- value product differentiation. This process was started approximately four years ago with a search for new cat litter products and other new product opportunities.

Jan 1, 1980

By John C. Draper

Little precise information is available on the effect of mining on the surface topography. It is often assumed that after mining the surface will simply sink. This is not an infallible conclusion as is well illustrated in two of the three examples herein. This paper describes the results of an attempt to precisely measure the surface movement in the area around coal pillars left in place for three oil wells in a completely mined and caved area at the Harwick Mine of the Duquesne Light Company. The dates when the various measurements were made are shown on the data sheets and indicate the rate of surface movement. These oil wells are identified as wells Nos. 2, 3, and 6. This mine property is located on the north side of the Allegheny River at Cheswick, Pennsylvania, and extends in a northerly and westerly direction about five miles. The three well pillars are situated on the westerly side of the Bessemer and Lake Erie Railroad some 2,000 feet from Rural Ridge, Pennsylvania (Fig, 1).

Jan 1, 1964

By George E. Valadão, Iván A. Reyes, Mizraim U. Flores, Armando C. Araujo, Rubén H. Olcay

Dewatering tailings to higher grades than paste produces a stable deposit that typically does not require retention dams and is called a “dry stack.” A proposal of different dewatering techniques applied in the fine tailings produced after final desliming phase, obtained from the treating of phosphatic ores, is the main objective of this work. The dewatering techniques evaluated were column thickener, deep cone classifier, and hyperbaric filtration. Calcite and dolomite were the main mineral contained in the phosphate tailings and these have a very fine granulometry; the tailings presented different behaviours related to the dewatering technique applied. The test column thickener and deep cone classifier with the best operational parameters found to obtain a maximum percentage of solids in mass were ~ 71% and ~ 67%, with values of yield stress ~ 200 Pa and ~ 100 Pa, respectively. In the hyperbaric filtration, a cake with ~ 10% moisture was obtained. This indicates that the transportation conditions are not the same. The overflow turbidity levels obtained from column thickener and deep cone classifier test did not exceed the value 100 NTU, whilst for the filtrate of the hyperbaric filter obtained values ~ 800 NTU. It was possible to preliminary estimate the recovery direct of water, considering each dewatering technique for final disposal of the tailings. The best dewatering techniques obtained were in the following order for the disposal in phosphate fine tailings dams; the hyperbaric filter showed an excellent dewatering capacity with productions rates around 160 kg h− 1 m− 2 for moisture cake of 10%, followed by the column thickener and deep cone classifier with paste ~ 71% of solids (W/W) and high-density slurry ~ 67% of solids (W/W), respectively.

Dec 23, 2023

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.

By Keith E. Meyers

Condition monitoring is a viable troubleshooting practice among many industries to extend equipment performance, minimize unplanned downtime, reduce maintenance and repair time and costs, and increase related aspects of plant safety. But obstacles abound for mining, mineral-processing and cement operations striving to implement the technologies. Harsh machine environments can muddy efforts. High vibration in machinery can interfere with wide-spread rollout. Staff expertise or skills may be lacking. And costs may be prohibitive. Fault detection has emerged as a practical and cost-effective solution to identify process and machinery faults before failure interrupts productivity or jeopardizes worker safety. Fault detection can be a stand-alone system or connected to plant automation.

Jan 1, 2005

By M. Szatkowski

The studies conducted by Laplante and coworkers (1983,1984) with flotation of galena and quartz, showed that the rate of flotation reaches a maximum value for a certain intermediate value of the air flow rate. A similar, though less pronounced, effect of the air flow rate on the selectivity was also observed. Luttrell and coworkers (1985) showed that the size of air bubbles has a significant effect on both rate and selectivity of coal flotation. These two studies used flotation tests in which no froth layer was formed. This note describes effects of the air flow rate and bubble size on the rate constant and selectivity of coal flotation, using a mechanical laboratory machine with a froth layer allowed to form. Experimental A raw, dry ground Illinois coal was used in flotation tests. The size distribution and ash content of the samples are : Particle size (µm) Weight (%) Ash (%) +600 4.30 41.7 600/200 43.05 19.0 200/74 22.25 16.0 - 74 30.40 24.0 average 20.8 No. 2 fuel oil with a concentration of 200 g/t of feed and M.IBC with concentrations of 11, 22, and 33 mg/L of pulp (128, 256, 384 g/t, respectively) were used as flotation reagents. Tap water with a natural pH of 7.0 to 7.8 was used throughout the tests. No other reagents were used. The starting concentration of coal in the pulp was 86 g/L. A standard flotation machine with the pulp volume of 5 L was used in experiments. Three different air flow rates were employed, resulting in three air escape velocity values of 14, 30, and 70 cm/min. The air escape velocity (AEV) was calculated as the ratio of air flow rate (Qa) to the slurry surface (Ss) in the machine. For a comparison, the upper limit of air escape velocity values used in commercial size flotation machines is between 70 and 100 cm/min (WEMCO, 1983). A machine consisting of a generator of fine bubbles and a separatory column, described elsewhere (Szatkowski and Freyberger, 1985), was used for some tests where bubble size lower than that generated in the standard machines was required. Prior to a flotation test, a batch of coal was mixed with water in the flotation cell for at least 10 minutes to ensure that all coal was thoroughly wet. Then the specified amount of fuel oil was added and the pulp was conditioned for five minutes. The specified amount of MIBC was added 15 seconds before the end of conditioning. After air flow was opened, flotation products were collected for 0 to 30, 30 to 60, and 60 to 120 second intervals. Content of the combustible material in samples was determined by subtracting the ash content from 100%. A photographic technique was used to determine initial distributions of bubble size generated by the flotation machines. Bubbles generated in water containing the prescribed amount of the frother but no solids were photographed against a black background. The average diameter and standard deviation were then calculated for each set of flotation conditions. The method gives results reproducible within k 5% of the average bubble size. Table 1 contains information about the measured bubble size distributions expressed by the average bubble diameter (Db) and the standard deviation ( SD ) . Results and discussion The general formula for calculating the flotation selectivity is: o = recovery of coal/recovery of ash (1)

Jan 1, 1988

By R. Kealey, D. Huo, Q. Zhang, Y. A. Sari

Greenhouse gas (GHG) emissions from primary mineral and metal production account for ~10% of global GHG emissions. One of the main sources of GHG emissions in mining operations is fuel consumption by haul trucks. Given their size and carrying capacity, the fuel consumption of haul trucks can approach 250 liters per hour. An average of 30% of the idle time of the trucks is spent while waiting in the queue. Inefficient truck dispatch planning can waste resources, cause dilution and elevate GHG emissions. In this research, a machine learning based truck dispatch approach was developed to dynamically route the haul trucks based on the loaded material, the road traffic, the estimated wait time, and the maintenance needs of the trucks. The GHG reduction potential of this smart fleet management approach was estimated by calculating and comparing the related carbon emissions versus scenarios using traditional fleet allocation approaches. Results suggest that this dynamic fleet allocation approach can significantly reduce GHG emissions at mineral production sites by optimizing waiting times and the overall distance travelled while achieving the same production levels.

Mar 2, 2022

By Joshua Cole, Joshua Sovechles, Christian Cardoso, Guillermo Bermudez, Martta Hirsi, Joshua Dettamanti, Rabia Abbasi

The implementation of technological advancements in flotation is key to optimize performance in mining operations. Consequently, flotation cell’s performance is highly dependent on the effectiveness of the mixing mechanism. A more efficient flotation mixing mechanism is likely to improve metallurgical performance and optimize energy consumption, which is the motivation for Metso’s journey to develop the latest iteration of FloatForce®. Looking to test the new design at plant scale, Metso approached the Kennecott Copperton concentrator, which is continuously looking for different venues to improve metallurgical performance. In this context, a test campaign was conducted to implement this new flotation mixing mechanism in their rougher circuit during 2024. The industrial trial consisted of several sampling campaigns assessing different operational parameters for comparison purposes around a 300m3 flotation cell. The effect of the new flotation mixing mechanism on the cell’s power draw was also studied. The results of this trial at Kennecott are presented in this paper. Overall new flotation mixing mechanism, FloatForce+ was seen to perform as well as the original FloatForce.

Feb 1, 2025

By George H. Roseveare

Early flotation dealt primarily with the bulk concentration of sulphide minerals or the separation of one sulphide from another and was referred to as oil flotation because oils and fats were used as reagents. The separation or concentration of one nonmetallic mineral from another developed later with the use of fatty acids. Fatty acids are organic acids present usually as glycerides in tall oil and oils of fish, peanut, cottenseed, soya beans and ethers of veg¬etable and animal origin. Some, of these oils and their derivatives were used by the Phoenicians as early as 600 B.C. in making soap, and the use of such reagents in mineral dressing is referred to as "soap flotation". The first use of oleic acid for the recovery of minerals was the early agglomeration process.' The coarse particles of ore, from 1/16 to 1/4 inch diameter, were coated with large amounts of soap or oil and after screaming from the gangue were recovered by screening, hydraulic or table classification. In 1886, a patent was issued to Mrs. Carrie Everson in which the essential feature was the constituted commingling of pulverized ore, fat or an oil, either animal, mineral, or vegetable, for the purpose of effecting .a. union of the free metal or metallic portion of the ore with such admixed material whereby the same may be changed in subsequent separation of quartz or other rock therefrom by washing or other suitable means. The patent mentions the use of red, cotton seed, caster, sperm and linseed oils, In the early use of collectors the amount of oil for froth flotation was often 2 to 6 per cent by weight of the ore rather than pounds per ton.

Jan 1, 1959

By Satoshi Honda, Mitsuru Shimizu, Tatsuji Nagao, Motoaki Kurisu, Hirokazu Izumi, Toshinori Takahashi, Hiroyuki Itoi

"1. INTRODUCTION Grade separation of roads and railway tracks is an effective method for solving traffic-related issues in cities. However, in urban areas where the existing traffic infrastructure is already overcrowded, construction of new roads often faces problems especially in the proximity of existing structures. This paper summarizes the construction plan and results of new road tunnel construction in the proximity of the piers of elevated tracks on the Tokaido Shinkansen railway.2. SUMMARY OF CONSTRUCTION AND ISSUES Auxiliary Route No. 26 as specified in the Tokyo urban plan is a project by the Tokyo Metropolitan Government, covering the construction of a new road with a total length of 22.3 km currently on the way to completion. In Shinagawa Ward, Tokyo, Auxiliary Route No. 26 is designed to cross the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line, so for this project, the East Japan Railway Company (JR East) was commissioned to design and build a road crossing under the railway tracks (Sumiyoshi Underpass). Figures 1 through 3 show a sketch of the Sumiyoshi Underpass. The Sumiyoshi Underpass was planned as a two-lane tunnel for vehicles, which was to cross under the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line at an angle of 70 degrees. The structure concerned is a single-story single-span box culvert structure with the following dimensions: 11.5 m wide, 7.7 m high and 31.6 m long. The Tokaido Shinkansen Line tracks were constructed on a girder-type elevated bridge built in the 1960s, and the foundation piles of the piers (P7 and P8) in the proximity of this crossing box culvert of RC structure were constructed using an earth drill method. The crossing structure for this project is located extremely close to the piers of the Tokaido Shinkansen railway tracks, with a minimal separation of 0.4 m, and the most significant issue of this project was construction in a manner that would not obstruct the normal operations of the Tokaido Shinkansen (Figure 4). Initially, we considered installing a temporary earth retaining structure in the proximity of the piers, cutting the ground and building an RC box, but concluded that it would be very difficult to apply this method because of probable excessive displacements in the Shinkansen railway piers. That is why we decided on the use of a non-open cut method in order to minimize the impact on the piers."

Jan 1, 2016