Search Documents

By A. Suarez, M. Menendez, M. R. Gent, P. Riesgo

"Recent requirements to reduce thermal coal plant emissions, and ultrafine coal's tendency to produce these emissions due to its typically high ash and moisture contents have limited the use of ultrafine coal. Ultrafine coal in beneficiation plants are usually either disposed of in tailing ponds at a loss in combustible material or disposed of by blending with coarser higher-grade products, resulting in a reduction in marketed product quality. A study of the options for processing ultrafine coal, consisting of < 200 µm hydrocyclone overflow, with 38.8 percent ash content is presented here. Ultrafine coal was processed based on 200-µm sieve bend and 10-µm hydrocyclone classifications, enhanced gravity separation (EGS) and froth flotation concentration as well as combinations of these. Yield, combustible material recovery (CMR) and product humidity were evaluated as test results.Depending on the processing applied, product ash content could be reduced up to 49.7 percent, and up to 95.8 percent CMR of the actual run of mill feed could be attained. All of the processing options analyzed could reduce produced thermal electric plant emissions due to ash and moisture from 22 to 38 percent of the actual unprocessed ultrafine coal product.Froth flotation was found to be the optimal process, yielding a product with the lowest ash content attained of 19.5 percent and CMR of 92.3 percent. Being the most versatile of the processes evaluated, it is capable of producing coal with varied ash contents but is subject to potential variations in coal flotability. The most complicated of the processing options, a combined sieve bend recovery of the > 200 µm fraction and EGS processing of the 10 to 200 µm fraction was found to be the next best option, attaining a combined 90.1 percent CMR and 25.0 percent ash content. IntroductionMunicipal, regional and national objectives to reduce fossil fuel combustion emissions and their effects on air quality and global weather changes are affecting thermal electric plant operations. Plans and regulations such as President Obama's Clean Power Plan (U.S. Environmental Protection Agency, 2015), the European Directive 2010/75/EU (European Commission, 2010) and China’s proposed Enhanced Actions on Climate Change (Wei, 2015) are of major significance to thermal electric plant operations. Although thermal plant efficiencies depend in large part on the losses of heat by plant components, the ash and humidity contents of thermal coal invariably reduce plant efficiencies and increase emissions of carbon dioxide (CO2), nitrogen oxides (NOx) and dust.Any noncombustible material present in thermal coal will result in higher CO2 emissions per unit of energy produced. Since no particle emission control can be totally effective, it is to be anticipated that any reduction in coal ash content will also result in reduced particle emissions. Kurose, Ikeda and Makino (2001) reported that NOx emissions also increase with coal ash content. The effect of coal moisture content during combustion is complex. Kurose, Ikeda and Makino (2001) showed that an increase in coal moisture content significantly reduces thermal NOx to total NOx production, and Bosoaga et al. (2006) showed that it tends to reduce NOx emissions. Since the humidity, pyrite and ash content of thermal coals directly affect thermal electric plant efficiencies and emissions, minimizing these factors should facilitate, at least in part, compliance with thermal electric plant emission limits. This, in turn, would affect the specifications and prices of the coal preparation plant products."

Jan 1, 2016

By John H. Bassarear

The never ending search for lower unit costs led Pima Mining Company&apos;s management to study various alternatives shortly after Expansion III was completed. It soon became apparent that a considerable amount of ore assaying 0.35% copper had to be moved in order to maintain mill feed at the desired 0.54% copper content, which is the overall grade of the ore reserves. Detailed investigations revealed that for a period of 8 - 10 years, about 14,000 tons per day of 0.30 - 0.40% copper ore would pass by the crusher en-route to the low grade stockpile. This ore is very hard, very clean and has to be mined at a relatively uniform rate. A six month pilot plant run testing autogenous and semi-autogenous grinding gave very encouraging results. Since no mining costs need to be charged to the extra tonnage (it had to be mined anyway) the only major costs would be against milling. The decision to proceed was made in August 1970 and Fluor-Utah was retained as the prime design construction contractor. Ore was first put through the new mill on December 29, 1971. By March of 1972 design tonnage of 14,000 TPD had been attained. The first three expansions at Pima Mining Company, 20 miles south of Tucson, increased mill capacity from 3,000 TPD to 36,000 TPD. These expansions included a separate, conventional, three stage crushing plant plus additions to the existing concentrator that primarily duplicated the then current flowsheet. Expansion IV, however, consisted of an entirely new and separate primary crusher and a completely new mill building located about 2,000 feet southeast of the 01 d concentrator. The new mill, using semi-autogenous grinding, produces scavenger and rougher flotation concentrates that are pumped to the old mill for regrinding, cleaning, thickening and filtration.

Jan 1, 1973

By Eugene C. Spilker

Cross country belt conveyors are becoming the preferred method of bulk material handling in the industrial complex. Installed cost, maintenance, reliability, simplicity and operating expense enhance this choice, especially when faced with rising cost and questionable availability of liquid fuels. Conveyor flights are getting longer, faster, and higher in capacity, and are being installed in rugged terrain. Rights of way are often difficult to obtain. All these considerations lead up to design aspects well beyond those for in-plant conveyors. This paper points out some of the aspects that lead to the successful design of a cross country belt conveyor system.

Jan 1, 1980

By Steve Kral

The third edition of the Underground Construction Association of SME?s (UCA) Cut-ting Edge series of conferences focused on a challenge every underground construction and tunneling project faces: controlling ground water. The conference, held in New York City in November, is a partnership between the UCA and The North American Tunneling Journal. It featured more than 20 technical presentations by professionals from around the world. Each described specific challenges unique to their projects and the solutions employed. More than 175 professionals attended the two-day conference that included an exhibition featuring 17 companies. In addition to the technical program, the Cutting Edge conference featured a site visit to the $10.4 billion East Side Access Project. Sponsors of the meeting included Soil Freeze, Traylor Bros., Kiewit, Skanska, Moretrench, Aecom and The Robbins Co.

By C. Garcia, A. Potulska, J. J. Opazo, T. Comi

"The Sierra Gorda SCM sulfide ore processing plant began commissioning in the third quarter of 2014. Located in the Atacama Desert in northern Chile, the project is an open pit mine and Copper-Molybdenum processing plant is one of the most highly-instrumented operations in the world. It is the first hard rock operation in Chile and the second in South America to utilize HPGR technology. It is a significant Molybdenum resource especially in the first five years and the Molybdenum separation plant is complex. Designed to process up to 60 million lbs. of fine Molybdenum per year, it uses the latest technology and equipment to ensure superior recovery and product quality. It also has gas handling and alarm systems to fulfil the Company’s vision of “Zero Harm”. This paper discusses the overall operation and issues relating to the concentrator start-up. These include a review of the mineral processing design, the unified process control center and management information systems, and the correlation of geological and metallurgical performance data (mine-to-mill) for use in anticipating and preparing for treatment of diverse ore deliveries. INTRODUCTION Sierra Gorda SCM is a joint venture partnership with KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining, and Sumitomo Corporation (Japan) operating in northern Chile. The Sierra Gorda open pit mine and Copper-Molybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, well-instrumented mine in Chile. This paper contains a general review of the project including geology and history. This was a very fast-track project going from greenfield site acquisition to mill start-up in 10 years. Highly-experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied. The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (see Figure 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km from the village of Sierra Gorda at an elevation of approximately 1,700 m above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic, and Escondida, to name a few."

Jan 1, 2015

By Brian Gettinger, Jim Schlaman, Alston Noronha

"INTRODUCTION The public understanding of green solutions today is based on the definition of sustainability adopted by the Brundtland Commission (World Commission on Environment and Development) in 1987: “development that meets the needs of the present without compromising the ability of future generations to meet their own needs.” Over time this initial definition evolved to identify three distinct factors impacting sustainability that are often referred to as the “Triple Bottom Line”: Economic, Environmental and Social. The triple bottom line approach seeks to drive outcomes that create maximum value for all stakeholders. In the last ten years purveyors of water and wastewater tunnel solutions have found themselves on the wrong side of a politically polarizing issue in the crosshairs of politicians, environmental activists and community groups branding tunnels as expensive, “gray” and not-sustainable. Tunnels under design were stopped and large planned tunnel programs were delayed or canceled. Therefore being sustainable and “green” is not simply using natural vegetation, but creating an asset that meets current and future needs and will not become a future liability. As this paper will discuss, tunnel projects embody a sustainable triple bottom line project well, are equally sustainable as green infrastructure, and have begun to gain awareness for their sustainability. GREEN INFRASTRUCTURE CHANGES TUNNELING LANDSCAPE The green movement quickly swept across the nation in the mid to late 2000’s and was a hot topic in the media and at all the local, regional and national industry conferences. Politicians espoused the benefit of green infrastructure including job creation, urban renewal, aesthetics, property values economics and sustainability. The political microscope was focused the closest on stormwater and wastewater management, particularly in communities responding to combined sewer overflow (CSO) consent decrees from the Environmental Protection Agency (EPA). As communities with CSO problems evaluated their long term control program (LTCP), local government officials and planners began to balk at the huge price tag required for compliance and began looking for alternatives. “Green” infrastructure was proposed as lower cost solution that could be used to offset capital-intensive “gray” infrastructure like new sewers, storage tanks, tunnels, and treatment facilities. In addition, including green infrastructure in a previously negotiated LTCP required a reset on the entire planning process, additional studies and more planning which would push capital investment further off into the future, subsequently delaying unpopular user rate increases. As a result, tunnel projects as well as trenched conveyance and treatment plant projects that had not yet started construction were stopped, delayed or substantially changed."

Jan 1, 2016

By Ernest L. Bradley

A positive pressure ventilation system, augmented by a dewatering well curtain and underground longhole drilling, provides effective ventilation and radon control at EXXON Minerals Company&apos;s Highland Underground Mine in the Southern Powder River Basin of Wyoming. Testing different types of bulkheads, sealants, and bleeder systems has led to improvements in the basic ventilation system. Continued testing of new or different materials and equipment is expected to lead to further improvement in the ventilation program. Effective training of both miners and supervisors is essential to maintaining and improving ventilation techniques. This paper addresses the ongoing ventilation program and experience to date at the Highland Uranium Mine.

Jan 1, 1979

By James R. Strong

Before getting into the subject of packaging and materials management, please permit me to introduce you to MICRO SWITCH. MICRO SWITCH, A Division of Honeywell Inc. is located in Freeport, Illinois. We manufacture and market thousands of types of precision snap-action electrical switches. Most of them are used as components by other manufacturers in industrial and commercial products. MICRO SWITCH also offers a broad line of industrial control devices including heavy- duty limit switches, relays, manual controls and proximity switches. Other product lines are solid state keyboards for the computer industry and high-performance d.c. motors used in computer related equipment. So you can see that we are a component manufacturer. With the exception of the keyboards, every one of our products would "fit comfortably into a breadbox." Some are so tiny that one could easily fit several thousand into a man&apos;s hat. In my position as supervisor-packaging. package design, and materials handling engineering, I am actively involved in package design projects, parts handling design projects, and numerous activities involving departmental layouts, storage facilities, and material handling equipment. Two package design technicians, a materials handling engineer, and a materials handling technician make up the technical staff.

Jan 1, 1973

By Ruichen Ren, Xu Han, Caixia Li, Zengchuan Yue

In this paper, the size-density distribution of coarse middling coking coal (CMCC) with different grinding fineness and flotation concentrates was investigated. Then, the flotation behaviors and liberation characteristics of different size-density fractions in ground CMCC were analyzed, and the different size-density fractions were divided into five categories: mostbeneficial, secondary-beneficial, poorly liberated, insignificant-pollution, and serious-pollution. Based on the content of particles with different liberation characteristics, an evaluation index of the liberation characteristic of ground CMCC, namely, the liberation perfection index (LPI), was proposed. The results indicated that grinding changed the size-density composition of CMCC, which affected the flotation performance. Insufficient grinding and overgrinding were not beneficial to flotation. Insufficient grinding caused a higher content of poorly liberated particles and a lower content of most-beneficial particles. Overgrinding increased the content of serious-pollution particles and reduced the content of most-beneficial particles. The size order of the LPI values of different ground CMCC was consistent with the flotation efficiency, and the LPI values of the other two similar samples were overall positively correlated with their flotation performance, suggesting that the method is universal.

Feb 14, 2023

By Florence Munter

This paper provides a discussion of the various federal and state laws governing water quality as related to mining operations. The specific laws addressed are the Clean Water Act, and the Arizona Mined Land Reclamation Act. Topics that will be addressed are mine water and process water discharges, storm water discharges, pollution prevention, dredge and fill, spill prevention control and countermeasure plan, and surface water protection. Proposed changes to the laws and regulations will be discussed. Compliance strategies will be suggested to prevent potential noncompliance and enforcement.

Jan 1, 1996

By W. R. Reed, G. W. Luxbacher

Mine worker exposure to respirable coal dust and silica dust can result in coal workers’ pneumoconiosis and silicosis which are occupational respiratory diseases that have no cure and are ultimately fatal. In 2021 the Mine Safety and Health Administration reported just over 11,000 operating metal/nonmetal mines with the potential for silica dust exposure for just under 200,000 miners. The National Institute for Occupational Safety and Health (NIOSH) conducts respirable coal and silica dust research associated with mining through its Office of Mine Safety and Health Research. NIOSH respirable coal and silica dust research began under the U.S. Bureau of Mines (USBM), which initially examined silica dust, progressing to include coal dust, with a stronger focus after 1969 with the passage of the Federal Coal Mine Health and Safety Act. A review of extramural research to develop real-time respirable silica dust monitor is presented along with a brief history of silica dust regulation.

Feb 1, 2024

By Cloyd D. McDowell

The Federal coal Mine Health and Safety Act of 1969 has been criticized by those who say it goes too far in controlling the activity of private enterprise and by those who say it does not go far enough in eliminating fatalities and accidents in an accident prone industry. Possibly a better evaluation of this legislation lies somewhere in between. From the viewpoint of the coal industry it can be said that through the efforts of those engaged in mining, both the operator and the miner, the year 1969 marked a record year in mine safety with only 190 fatalities and a frequency of 0.84 per million man hours exposure. This outstanding achievement compared to any previous was the result of a determined effort on the part of a concerned industry to improve its reputation as being the most hazardous industry in the nation. After the effective date of the Act, March 31, 1970, the Bureau of Mines assumed complete control of all safety and health activities of the mining industry. Unfortunately, there was no improvement in the safety record of underground mines in 1970 with the total of 255 fatal injuries and a frequency of 1.04 for the year. The number of fatalities declined to 177 in 1971 but the number of underground coal mines had declined from 5,955 to 2,268 during the two year period. Meanwhile, surface mined coal increased from about 38% of total production in 1969 to over 50% in 1971, keeping the annual production of coal at a normal level but involving fewer men.

Jan 1, 1973

By A. Cecala, J. Noll, J. Hummer

The National Institute for Occupational Safety and Health has observed that many control rooms and operator compartments in the U.S. mining industry do not have filtration systems capable of maintaining low dust concentrations in these areas. In this study at a mineral processing plant, to reduce respirable dust concentrations in a control room that had no cleaning system for intake air, a filtration and pressurization system originally designed for enclosed cabs was modified and installed. This system was composed of two filtering units: one to filter outside air and one to filter and recirculate the air inside the control room. Eighty-seven percent of submicrometer particles were reduced by the system under static conditions. This means that greater than 87 percent of respirable dust particles should be reduced as the particle-size distribution of respirable dust particles is greater than that of submicrometer particles, and filtration systems usually are more efficient in capturing the larger particles. A positive pressure near 0.02 inches of water gauge was produced, which is an important component of an effective system and minimizes the entry of particles, such as dust, into the room. The intake airflow was around 118 cfm, greater than the airflow suggested by the American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ASHRAE) for acceptable indoor air quality. After one year, the loading of the filter caused the airflow to decrease to 80 cfm, which still produces acceptable indoor air quality. Due to the loading of the filters, the reduction efficiency for submicrometer particles under static conditions increased to 94 percent from 87 percent.

Jan 1, 2015

By J. H. Daniel

Dust-related respiratory disease remains the major health concern in mining, and health agencies are proposing more stringent standards. The U.S. Bureau of Mines (USBM) is investigating techniques to continuously monitor respirable dust in real-time during the coal or ore extraction process. Continuous monitoring will allow mine operators to evaluate hazardous dust concentrations and adjust the operations to produce less dust. Mine instrumentation applications include machine-mounted and hand-held monitors, personal monitors, and area/environmental monitors. Six dust detection methods have been considered to meet application requirements. These are: light-scattering instruments, a smoke-particle detection technique, correlation of pressure drop across the collection filter with amount of dust deposited, the Tapered-Element Oscillating Microbalance (TEOM) instrument, a method that relates the amount of dust collected on a filter with the vibration of the filter, and beta attenuation measurement of dust. Studies to date have identified the TEOM instrument and the technique of correlating the amount of dust collected with the vibration ofthe filter as having the most promise for success. Development of the machine-mounted monitor is the highest research priority. The application options and progress to date in developing continuous monitoring instrumentation are presented.

Jan 1, 1995

By A. Leppala

Scope of the Courier 300 System The fact that reliable on-stream analysis is a prerequisite for effective flotation control is hardly disputed today. Nevertheless, up to now no system has been available that includes all the equipment necessary for successful analysis. However essential an on-stream analyser is in itself, reliable and accurate assaying can only be assured after techniques for sampling, handling the slurries and computing the X-ray data have been developed for the purpose. The Outokumpu Company&apos;s Courier 300 System is a complete package that can be installed and handed over with the key. It includes the equipment needed for sampling and handling the slurries. It has been developed from the start to meet industrial demands. Obviously an on-line system must comply with far stricter standards than one designed for a laboratory. Assays are computed by an Outokumpu 316 digital data processor, which is an integral part of the system and controls its entire performance. The computer software is programmed as a standard package, including a highly advanced new model for assay computation. Analysis output is available for a process computer, report typewriter:, and recorders. The package also includes calibration for slurry assays at our pilot installation before delivery. A complete Courier System can analyse up to 4Z slurries and six elements in each slurry. Thanks to its modular design, it can be dimensioned initially to the customer&apos;s requirements and is easy to expand later at low cost. Being a mining company itself, Outokumpu has been able to utilize its own long experience in non-ferrous metallurgy - an important factor contributing to the success of the Courier system. History of the project and present installations The first on-stream analyser was installed at Outokumpu&apos;a Pyhasalmi Con¬centrator at the end of 1967, after several years&apos; development. Since then,

Jan 1, 1971

By A. O. Drysdale

From a mining point of view the Portland Cement Industry falls logically into the Industrial Minerals Division. Portland Cement manufacture requires four principal materials, lime, silica, alumina and iron. The usual source of lime is limestone. Silica sources include clay, shale, quartz, sandstone and sand. Alumina is usually provided by selecting a silica source with a suitable alumina content such as clay and shale. "Cement Rock" is occasionally found in which all four ingredients are found in natural combination or sufficiently close that only minor adjustments are required. In the absence of iron oxides a white cement can be produced. All raw materials used in Canada contain some iron and in most plants further minor quantities of iron are added to promote fluxing, hence the typical grey colour of Portland cement. The modern period in cement manufacturing started in 1824 when Joseph Aspdin of England patented a process for the manufacture of a modified hydraulic cement which he called "Portland Cement". Hydraulic cements are cements that harden under water. Although natural cements, made by calcining and grinding natural argillaceous limestone were produced in Canada as early as the 1830&apos;s, Portland cement was not produced in Canada until 1890, about 18 years after it was first made in the United States.

Jan 1, 1964

By W. R. Junge

The investigation, selection, and implementation of remedial activities for large, complex mining and milling sites is dependent on the cost-effective management of tailing and waste materials. Site investigations evaluate the contaminant source areas, assess the potential release rate of contaminants, and determine the acceptable contaminant release rate for the site. Selection of appropriate remedial activities is based on evaluation of constructability, reliability, performance, effectiveness, permanence and cost. Remedial technologies available for tailing and waste material include removal, consolidation, capping and drainage control. Proper implementation and documentation of the selected remedial activities are critical to the overall success or failure of the remedial program. A step-by-step process, established at the initiation of a project, should accurately document all construction activities, monitor environmental conditions at the site, assess the performance of the remedial activities, and, ultimately certify that the remedial activities have met relevant and appropriate standards. Case histories are presented for a uranium mill at Uravan, Colorado and a lead, zinc mine at Gilman, Colorado. These case histories provide examples as to the combination of remedial technologies that have been applied at these specific sites.

Jan 1, 1989

By Richard A. Grieve

A 63.5 metric tons per hour (70 TPH) demonstration coal preparation plant was constructed on the Iowa State University campus, Ames, Iowa, as a part of the Iowa Coal Project funded by the state of Iowa and administered through the Energy and Minerals Resources Re-search Institute. Processing equipment in the plant circuit includes a heavy media separator, concentration tables, separating and dewatering screens, and conveying equipment. Coal samples of size 907 metric tons (1000 tons) with sulfur contents ranging from 2.5 to 8.75% sulfur from seven mines in the state of Iowa have been pro-cessed in the plant. Sulfur reductions have averaged 35%. With ash reduction averaging 45%. Equipment for advanced fine coal beneficiation research is currently being installed in the plant to include a slurry pretreatment circuit, froth flotation, oil agglomeration, pelletization, hydrocyclones, advanced design thickener and disc filtration.

Jan 1, 1978

By T. J. Lutz, S. Gallagher, J. R. Srednicki, J. J. Sammarco

The Illuminating Engineering Society of North America reports that an underground mine is the most difficult environment to illuminate (Rea, 2000). Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) are conducting ongoing studies designed to explore different lighting technologies for improving mine safety. Underground miners use different visual cues to escape from a smoke-filled environment. Primary and secondary escapeways are marked with reflective ceiling tags of various colors. Miners also look for mine rail tracks. The main objective of this paper is to compare different lighting types and ceiling tag colors to differentiate what works best in a smoke-filled environment. Various cap lamps (LED and incandescent) and lasers (red, blue, green) were compared to see which options resulted in the longest detection distances for red, green and blue reflective markers and a section of mine rail track. All targets advanced toward the human subject inside of a smoke-filled room to simulate the subject walking in a mine environment. Detection distances were recorded and analyzed to find the best cap lamp, laser color and target color in a smoke environment. Results show that cap lamp, laser color and target color do make a difference in detection distances and are perceived differently based on subject age. Cap lamps were superior to lasers in all circumstances of ceiling tag detection, with the exception of the green laser. The incandescent cap lamp worked best in the simulated smoke compared to the LED cap lamps. The green laser was the best color for detecting the tags and track compared to the red and blue lasers. The green tags were the easiest color to detect on the ceiling. On average, the track was easier for the subjects to detect than the ceiling tags.

Jan 1, 2013

By John K. Liu

The trend to larger grinding mills, requiring total drive power in the range of 10,000 KW(13,400 HP) or so provides the incentive for developing new power transmitting techniques, since conventional girth gears are limited to about 3700 to 4500 KW per mesh (5000-6000 HP). For the immediate future, the synchronous motor, with its beneficial power factor, and the squirrel cage induction motor, with its high reliability record and low maintenance, still promise to be the best choice for prime mover(s). Due to the abovementioned single mesh power limitation of the gear train, however, two or more motors must be combined to attain the required drive power. This paper describes a scheme for coupling these motors to the mill using a straightforward, essentially mechanical means that is based on proven components and controls.

Jan 1, 1977