Search Documents

By D. M. Range

Exxon is reclaiming an 80-hm2 (200¬acre) Wyoming uranium tailings basin in accordance with US Nuclear Regula¬tory Commission (NRC) requirements. The reclamation plan is designed to control the tailings and their radioactive emissions for at least 1000 years. Rigorous modeling and analyses of potential erosion by wind and water were used in planning. The use of riprap was minimized and the need for long¬term reclamation maintenance was eliminated. The resulting design is simi¬lar to regions stable from erosion cre¬ated by nature. The concepts used in the design and implementation have wider reclamation application. Highland history Exxon operated the Highland uranium operations from 1972 until mid-1984. Open pit and underground operations mined the roll front, sandstone ore body. The 2.5 kt/d (3000 stpd) mill employed conventional crushing, grinding, sulfu¬ric acid leach, CCD, SX, precipitation, and drying circuits. The mill produced 10 Mt (11 million st) of tailings. An¬other operator began commercial scale in situ leach operations in 1988. The tailings basin was constructed by deposition of mill tailings in a natural ravine dammed with a 30-m (100-ft) high by 1050-m (3400-ft) long clay core earthen dam built entirely downstream of tailings. Figure 1 shows the layout of the tail¬ings basin in 1984. Tailings were de¬posited along the dam face on the east side of the basin as well as in the west end and along the south edge until the early 1980s. This left a deep water pond in the middle of the basin. The deep pond was largely filled with tailings during the last four years of mill opera¬tions by the construction of two tailings causeways and the operation of a float¬ing tailings line. The pond water volume was mini¬mized by recycling tailings water to the mill and by operating a 32-L/s (500¬gpm) evaporation enhancement spray system during the last few years of mill operations. Regulatory requirements Several conceptual tailings basin rec¬lamation plans were prepared during the mine life. In September 1984, Exxon began preparation of a detailed plan in response to an NRC request. Water, Waste and Land Inc. (WWL) of Fort Collins, CO was selected to help pre¬pare the plan that was submitted to the NRC in December 1984. The design had to meet the require¬ments found in NRC regulations (NRC, 1985). These were based on regulations prepared by the Environmental Protec¬tion Agency (EPA, 1983) at the man¬date of federal law (UMTRA, 1978). The NRC regulations contain strict primary standards and a somewhat more flexible set of secondary standards. The primary standards include requiring that: • radiation from tailings be reduced to background levels; • radon gas emitted by the tailings be reduced to 20 pCi/m2/s from the surface of the reclaimed tailings pile; • tailings not be dispersed into the environment; and • these conditions endure without routine maintenance for at least 200 years and for 1000 years to the extent reasonably attainable. The lengthy time requirements pre¬sented a large engineering challenge. Radon is a radioactive, chemically inert gas with a 3.8 day half-life. It is released from uranium tailings by the radioactive decay of radium, which, in turn, is a radioactive decay product of uranium. Radon emissions from ura¬nium tailings can be controlled with an earthen cover thick enough that the radon gas decays to its solid, short-lived radio¬active daughters before the radon dif¬fuses through the cover material into the air.

Jan 1, 1989

By Shankar S. Hegde

In many areas of the United States much of the most readily minable coal is nearing depletion, while at the same time, increased national attention is being given to coal as a major alternate energy source. If some of the thinner, more erratic, deeper and lower quality coals, which comprise the great bulk of U.S. resources, are to be mined efficiently and economically, greater attention must be devoted to careful planning of mines and to preparation facilities. One of the cornerstones to careful and successful mine planning is precise knowledge of coal thickness and areal distribution, roof and floor quality, and seam quality. Data on which this knowledge is based are obtained from various borehole techniques and, in some cases, seismic methods. Despite the many technical innovations that have been made in acquiring subsurface data, little attention has been given to the problem of systematic storage and retrieval procedures of the data and assembling them in a form that can be used for various computer mapping programs now available. (See Bilter and Martin, 1977; Bryant and Zobrist, 1977 and Farrell and Wherry, 1978). The purpose of this paper is to describe a series of user oriented programs developed over the past five years which are specifically designed for precise logging of rock core, accurate storage and retrieval of this data, correlation of seams between logs, tagging seams, computer assisted data posting of maps and preparing maps and profile sections for report illustrations. The entire system stresses increased precision and speed for a series of operations which are now largely manual, time consuming and prone to error.

Jan 1, 1980

By T. Hayes

Track-type tractors remain one of the most cost-efficient stripping tools available to coal miners. Whether they are "sweetening up" a dragline operation with pre-benching or serving as the primary stripping tool, dozers can play an important role in driving down mining costs. This paper reviews the application zone of track-type tractors. In addition, it provides tips on site set-up, equipping of tractors, and machine operation which the audience can take home and apply.

Jan 1, 1996

By D. P. Caplice

On behalf of the Ontario Water Resources Commission, I would like to express my sincere appreciation to your Institute for presenting us with this opportunity to outline the regulatory control programme as it relates to the mining industry in the Province of Ontario. In Canada, and particularly in Ontario, we are blessed with an abundance of natural resources. Fresh water in the form of lakes and rivers covers nearly 17 per cent of the area of the Province. (Total area of the Province of Ontario is 412,582 square miles.) The mining industry, which had its beginning in the early 1800's with a small iron ore plant, has progressed with the major discoveries of nickel and copper in 1883, silver in 1903, gold in 1908, iron in 1939 and uranium in 1953, to the point where, in 1966, almost one billion dollars in mineral wealth was mined in Ontario. Water, in spite of its great abundance and with due respects that it may become a natural resource worthy of export in the foreseeable future, has become increasingly precious in Ontario, particularly in the more urban areas in the southern part of the Province.

Jan 1, 1968

By J. E. Lonergan

The in-pit placement of crushing and conveying equipment results in a flattening of the pit slope of a multiple-bench open pit mine. To maximize the economic benefit of lower haulage costs associated with in-pit conveying, one must minimize the cost of the flatter slope which is expressed in terms of additional stripping or tied up ore. A computer program that compares the tonnage aspects of various conveyor layouts will be discussed.

Jan 1, 1985

By Henry N. Doyle

One can hardly discuss coal pneumoconiosis unless it is placed in the context of the total pneumoconiosis problem in the mining industry. However, it might be well if first we defined a few terms, since it has been my experience that the use of the word pneumoconiosis frequently causes con- fusion among those who are not familiar with the term. Pneumoconiosis comes from two Greek words meaning lung and dust. Hence, the word pneumoconiosis simply means dusty lung, or dust on the lung. There are many forms of the disease, some of which are disabling and some are not. Among the many dusts which cause pneumoconiosis might be included silica, asbestos, coal, talc, iron ore, and many other mineral dusts. Silicosis is a specific form of pneumoconiosis. It is caused by the inhalation of excessive amounts of silicon dioxide in the form of crystalline quartz. The disease is manifested by nodulation of the lungs which is apparent on an X-ray film. Continued exposure to silicon dioxide causes the nodules to grow and ultimately large areas of the lung become scar tissue which pre- vents the lung from performing its physiologic function. In its more advanced stages, there is a significant loss of pulmonary function which accounts for

Jan 1, 1966

By W. A. Haley

Wheel loaders became important bulk materials handling tools in the early fifties. As they grew in stature, productivity, reliability, and acceptance, the demand for larger, more rugged machines evolved. In the early sixties, the introduction of a 6-yard model by a major equipment manufacturer led quickly to widespread experimenting and rapid worldwide acceptance in loading blasted rock in stone quarries and smaller metal mines. As the wheel loaders grew in popularity for shot rock loading, larger models, 12- to 15-yard size were developed and saw widespread use by 1970. In the past 20 years, at most quarries and small to medium size mines, most cable operated power shovels have been replaced by large wheel loaders and more recently, hydraulic excavators as the primary loading tool. Wheel loaders larger than the 15-yard class are not used widely. Until about 1970, very few overburden haulage trucks were used in domestic coal mines. About that time, many states started enforcing stringent mine relcamation regulations and in 1977, even more stringent federal legislation was passed. These controls brought about drastic changes in coal surface mining methods in the mountainous areas of Appalachia, in smaller midwestern mines and in the large mines of the western states. Basically, simple material casting methods were replaced at most eastern mines by "haul-back" and "mountain top mining" methods using controlled placement of overburden as it is removed from the coal. These methods dictated much more extensive use of loaders/ shovels and trucks to the point that most coal mining in those areas is now by loader/shovel trucks methods. And those areas have become the home of the country's largest population of large wheel loaders and trucks in the 35- to 85-ton size class with a trend to even larger trucks and shovels. To maintain equal production or provide for growth, the new methods have caused a sharp increase in machine intensity to the extent that at some mines, up to three times as many machines were required to mine a million tons of coal in the late seventies as compared to the machine needs in the sixties. Mining costs and coal prices also took a big jump in the mid-seventies, paralleling the drastic price increases in oil and other forms of energy.

Jan 1, 1984

By Remo Grandori

The Umiray Angat 13,2 km long tunnel in Philippines have been bored through extremely variable and difficult ground conditions including a number of special events. In particular the following adverse conditions were found: faults in decomposed ground, high temperature rocks, extremely rapid and important convergence phenomena, water inflows up to 800 litres per second. The special El Nino climatic conditions caused a long dry season and lower the level of the lake that was granting the access by barge to the site under the minimum navigable level. Many equipment have had therefore to be transported to site by a 10 ton capacity helicopter, after having been partially dismounted. For the same reason most of the tunnel drive have been bored servicing the site by 1 ton capacity helicopters to transport materials, spares and personnel. In order to overcome the above geological and logistic problems several innovation were introduced and tested in this project. Despite all that difficulties the 13,2 km of tunnel were bored in about 24 months, with a global average of 500 m/month.

Jan 1, 2001

By Kurt M. Larson

Future haulage cost projections led Foster Yeoman Limited into developing a fully mobile crushing and conveying system at its Torr Works quarry in Somerset, England. The purpose-built system has an effective throughput of 2,500 tonnes/hour and features an Orenstein and Koppel (O & K) manufactured walking frame, a Fuller-Traylor type 54 X 74 TC gyratory crusher, and unique mobile conveyor modules designed and manufactured by Foster Yeoman. Used in a single-bench operation in this 6 million-tonne per annum limestone aggregate quarry, the system is fed at the production face by 2 Caterpillar 992C loading shovels. The entire system is moved on a daily basis following production face locations.

Jan 1, 1986

By C. C. Stewart

Jim Walter Resources, Inc. operates four underground coal mines in Alabama. In 1986, during longwall recovery operations, sparks from a torch ignited methane that migrated onto the face after a roof fall. The fire quickly spread to the gob at the tailgate end of the longwall. The fire was successfully "area" sealed and mining operations resumed after five weeks. However, several problems were encountered during this process. This paper describes the events following the fire, methods used to control the situation, problems encountered, and steps taken to ensure preparedness for any future occurrences of this type.

Jan 1, 1993

By A J. Jonaitis

The DENVER Tube Press is a simple, high pressure (1500 PSI (100 bar» filtration unit, developed for processing difficult-to-dewater materials and to produce a handleable filter cake and clear filtrate product. Lab and pilot testwork conducted in Australia on coal fines (55-70\ -35 micron (400 mesh)) have shown that total moisture contents of less than 20\ are consistently achieved in the final cake products from the Tube Press. Currently, these coal super fines are sent to waste due to uneconomical mechanical dewatering methods, which were only able to reduce total moisture levels in excess of 30%. Calculated, throughput rates for the 500 Series Tube Press exceeded 1700 kg/hr (3750 lbs/hr). Feed solids concentration requirements are between 45 and 50\ to achieve these results.

Jan 1, 1993

By Brian Ulrich

The majority of individuals involved in the mining industry can appreciate and under-stand that mining is an activity that is necessary to satisfy the very basic needs of society, and to assist in accommodating our ever-changing world. As the expression goes, ?if it can?t be grown, it has to be mined.? And at this point in time, society has granted the mining industry the right to go about the business of mining, with the general anticipation that the work will be carried out without causing undue harm to the environment or populations in and around the mining operation. The term ?sustainable development? is gaining momentum as a popular concept, and indeed it has become something of a catch-all phrase, but it is important that the idea behind the term is not cast aside as a nonsense buzz word, as it simply is an indication that development (e.g. mining) can be satisfactorily carried out with an eye toward stewardship of the environment and society. On Feb. 19, 2010, a round-table discussion (Roundtable 2010) on ?Strides Toward Sustainability in Mining? was hosted by Knight Piésold and Co. (Knight Piésold) at the Red Lion Inn and Casino in Elko, NV. Knight Piésold had local representatives (Bryan Ulrich and Steve Boyce), as well as representatives from other office locations (Cynthia Parnow and Rick Damiani from Denver, CO, and Rick Frechette from Tucson, AZ) to help facilitate the discussion. The meeting played host to 30 attendees from five states. Attendees included personnel from nine mining properties and various corporate offices. The majority of participants were people who are directly involved with environmental work on a day-to-day basis. Others were project managers whose jobs involve some level of environmental focus.

Jan 1, 2010

By R. N. Chakravorty

It is well established that coal can react with oxygen in air at ambient temperature and as a result heat is produced. If the heat is not fully dissipated the temperature of the coal mass will increase, thereby enhancing the rate of oxidation with a greater production of heat. If this phenomena continues, the coal mass can ignite under favourable heat accumulation conditions. A number of mine fires are caused each year due to this phenomena, commonly known as spontaneous combustion. The early detection of spontaneous combustion is of prime importance to mining engineers since any fire which could be detected at an early stage may save the mine from considerable damage and subsequent loss of production. Obviously, there is no single general criteria by which one can assess whether the under- ground mining of a coal seam will result in liability to spontaneous combustion. This has made it imperative to develop systems for the early detection of heating and to follow its development. In recent years considerable advances have been made in the design and development of methods for the early detection of spontaneous combustion. The Mining Research Laboratories (CANMET) is presently investigating the problem of spontaneous combustion in coal mines with Kaiser Resources Ltd. at their hydraulic mine at Sparwood, B.C. on a co-operative basis, and some of the work was described earlier in the Canadian Institute of Mining & Metallurgy Bulletin (1,Z). This paper summarizes and updates the work done by CANMET on the detection of spontaneous combustion in coal mines.

Jan 1, 1980

By Bastiawarman Rifki, Nugraha Nico, Priatna Anton

The Deep Mill Level Zone (DMLZ) is one of the underground mines operated by PT Freeport Indonesia (PTFI). DMLZ is located approximately 1,500 m below ground level, where dominant rock types are skarn and diorite. The DMLZ mine and layout was designed based on the previous mine located above ground, the Deep Ore Zone (DOZ). The DOZ mine, located approximately 1,000 m below ground level, was a proven success, with a maximum capacity of 80K tonnes per day. During the production ramp up, which started in 2015, the DMLZ experienced several seismic events. The most significant event occurred in January 2018 with a recorded magnitude of more than 2.0 Mw, which resulted in a 14-month delay of the undercutting until March 2019. The significant event in January 2018 required the DMLZ to apply several adjustments related to the mining plan to help ensure it could continue development and achieve production target safely. This paper will describe the changes in the DMLZ mine plan as a response to the seismic activity at the mine, the reason behind the decisions being made to change the mine plan and strategy, as well as strengths and weaknesses between the previous plan compared with the new plan.

Apr 26, 2022

By F. Habashi

Brazil is a major mineral and metal producer, has magnificent fauna and flora, and superb architecture. In 1693 gold was discovered in Ouro Preto and Brazil produced about half of the world's gold. In 1726 diamond was discovered in the region of Tijuco in the Province of Minas Gerais, 150 km east of Bello Horizonte. The country became independence from Portugal in 1822 as the Brazilian Empire. In 1876, an Englishman succeeded in obtaining from the Amazon region seeds of rubber trees and secretly transferred them to England, where they were planted in the royal gardens at Kew. Some of the seedlings which spouted were sent to Ceylon and Singapore. Thus, began the rubber industry in the East. Today, Brazil is the largest producer of niobium, and produces a large number of other metals. The Mineral Research Center in Rio de Janeiro is the countries main Government establishment for mineral research. The country has been a republic since 1889 with its capital in Brazilia.

Jan 1, 2009

By James W. Bass

Atmospheric fluidized bed combustion (AFBC) is an improvement in coal-fired boiler design that offers several advantages over conventional boilers. AFC can meet sulfur and nitrogen oxide emission regulations without the need for add-on flue gas treatment equipment. The relatively low combustion temperature inhibits ash melting, thus reducing slagging and fouling which can, in turn, increase a boiler's fuel flexibility. This report discusses, in general, AFBC technology and, in particular, progress at the 20-MW Pilot Plant built by the Tennessee Valley Authority (TVA) at its Shawnee Power Station near Paducah, Kentucky.

Jan 1, 1985

By J. D. Brown

The purpose of this paper is to inform members of the coal producing and consuming community about techniques used by The Carter Mining Company to control product quality at a large surface coal mining operation. During the early years of mining operations, coal quality received adequate attention but the Company's main emphasis was to build up its production rate and minimize mining costs. While these goals are still of prime importance, coal quality has received substantial attention in recent years. A Company guideline that no coal shipment shall exceed any contract or company-imposed coal quality specification has been successfully implemented. To implement this guideline, geology and coal quality modeling procedures were improved, in-pit drilling and blending programs were refined, and detailed shipment procedures were developed. Background Surface coal mining of subbituminous C rank coal in the Cillette. (Campbell County) Wyoming area has become increasingly competitive during recent years. Prior to 1974, one small surface mine produced coal for local consumption. During the last ten years, 13 new surface coal mines have been constructed. Coal production from Campbell County, Wyoming totalled 88 million short tons (79.8 million metric tons) in 1983, the majority being shipped to electric utilities in the central and southern United States via unit trains having a capacity of 10,000 short tons (9,072 metric tons).

Jan 1, 1984

The recent mine disasters in Australian coal mines have initiated an introduction of Self-Contained Self-Rescuer (SCSR) as component in the development of new escape strategies for miners. These self-contained self-rescuers are closed circuit, demand sensitive breathing apparatus that make oxygen available to the wearer for a nominal period of time. Their operation is completely independent of the surrounding atmosphere. Once properly donned, the SCSR can assist a miner to escape from an area containing smoke, toxic gases or an oxygen deficient atmosphere. The duration of a typical SCSR is usually taken at the point of complete collapse of the breathing bag which is accompanied by an increase in breathing resistance and inhaled levels of carbon dioxide. Because the oxygen consumption (V02) and the heart rate are correlated, a prediction of V02 and consequently the duration of an SCSR can be made by monitoring the heart rate. Thirty-seven volunteers participated in field simulated escape trials at four underground coal mines. The results from the field trials suggested that oxygen consumption depends on the heart rate, the body weight and exercise rating of the miner. All the volunteers were asked to fill out the questionnaires to evaluate the performance of the units. The miners indicated that they could tolerate the inhaled temperature without any difficulty to breathing resistance. A complete statistical analysis of the field results is also presented.

Jan 1, 1997

By B. Anameric, S. Kawatra

Pig iron nuggets, which have similar chemical and physical properties with blast furnace pig iron, were produced by a single step heat treatment of self reducing – fluxing dried greenballs. During this single step heat treatment the transformation of self reducing fluxing dried greenballs into pig iron nuggets did not take place instantaneously. Rather, it was composed of three transformation stages, (1) transformation of self reducing – fluxing dried greenballs into direct reduced iron (DRI), (2) transformation of DRI into transition direct reduced iron (TDRI), and (3) transformation of TDRI into pig iron nuggets. Thus, the objective of this research was to investigate these transformation mechanisms by analyzing the transformation stage products. The transformation stage products were produced at a constant furnace temperature of 1425°C and various furnace residence times. They were characterized according to their microstructure, microhardness and apparent density. The changes in the product’s physical and chemical properties with furnace residence time were utilized in understanding the transformation behavior, the chemical events that took place and the controlling mechanisms. It was determined that the transformations were dictated by the changes in the slag viscosity and wetting properties, and by carbon diffusion into metallized areas.

Jan 1, 2007

By Adrian Brown

Floor heave can be a major problem in large open pit mines. Unrestrained floor heave can lead to flooding, equipment destruction, slope instability and subsidence. It is particularly troublesome in coal mines where the floor is frequently relatively flat, and is often underlain by major water Searing units. This paper examines methods of analysis used in computing floor stability, and sets out a simple rational method of evaluating the required level of water pressure control to maintain acceptable floor stability. The approach is illustrated by reference to the stability of the floor of the Morwell open cut lignite project in Southeast Australia, where this approach has been used successfully for over a decade.

Jan 1, 1982