Search Documents

By Michael M. Kimberley

Gold is sufficiently valuable that concentrations as small as 1 p.p.m. may support low-cost mining. Mindful of this, Sunoco Energy Development Company (Sunedco) obtained fire-assay analyses on some sulfide-rich sandstone encountered during routine drilling. Initial fire-assay values from independent laboratories indicated some significant gold values and independent analysis by atomic-absorption spectroscopy also indicated detectable gold at economically interesting concentrations. Sunoco geologists realized the potential for spurious results inherent in both fire assaying and atomic-absorption spectroscopy. Fire assaying that relies on gold measurement by weight requires perfect separation of gold from all other elements, Imperfect separation may artificially enhance apparent gold concentrations. Atomic-absorption-spectroscopy (AAS) measurements are potentially subject to interferences from other elements. For example, Beamish and Van Loon (1977, p.4) report AAS measurements of 4 p.p.m. Au to be characteristic of completely barren soil samples when samples are prepared by standard dissolution in HC1 to form solutions of about 10,000 p.p.m. total cations (mostly Na, Ca, Mg, Al, and Fe) .

Jan 1, 1981

By Cyril W. Draffin

Introduction Americans have long been proud of their ability to recognize a need, define it, and then develop workable solutions. The U.S. underground coal conversion (UCC) program is a good example. In 1974, the need to utilize coal resources that could not be mined was recognized, and Congress gave the Bureau of Mines $1.7 million to gain a better understanding of the UCC technology and its potential applications. Since 1977 when the U.S. Dept. of Energy (DOE) was formed, workable technologies have been tested, the market for underground coal conversion has been recognized, and extensive industrial interest has developed. Perspective The U.S. is blessed with extensive coal resources. Coal supplies about 19% of our national energy needs, yet recently promulgated environmental standards and increasing mining costs have limited direct coal use. UCC potentially can use coal that is economically or technically infeasible to mine because the coal is too thick, deep, dirty, high-ash, and wet; has an excessive angle of dip; or has unpredictable and poor overburden characteristics that make mining unsafe. Coal can be gasified underground or perhaps liquefied below the earth’s surface. Underground coal gasification (UCG) is the prime element of the underground coal conversion program. It enables coal to be converted to gas underground. UCC Coal Resource Recent data show a total U.S. coal resource base of about 6.4 trillion tons. Of this, 1.8 trillion tons might be accessed by UCC, including some minable coal. A commercial UCC process could quadruple roughly the 450 billion tons of U.S. coal reserves, which presently are recoverable by mining. The U.S. coal resources are divided into five sectors. The two most eastern sectors contain relatively thin, swelling bituminous coals that are difficult to gasify. Of the two, the bituminous coal in the Eastern Province is the most difficult because it is deeper than , in the Interior Province and the terrain is more rugged. The sector along the Rocky Mountains contains huge amounts of thick low-rank coals that are the most promising for early development by UCC. The coal has good continuity and the terrain is suitable. Low-rank coals such as subbituminous and lignite are highly reactive and tend to shrink and disaggregate when heated. Most of the coal in the Pacific

Jan 1, 1980

By Yi Luo, Jeremy Slagley, Arunkumar Rai, Steve Guffey, Syd S. Peng

Research was conducted to study the characteristics of longwall mining machine noises and to develop engineering controls for the reduction of noise exposure at longwall faces. Time-motion noise dosimeter data was analyzed and compared with existing databases. Experiments were conducted above ground on a stage loader/crusher to explore the potential of using active noise control (noise cancellation) in reducing the noise levels. A 5-7 dBA reduction in recorded stage loader noise was achieved. This paper presents the equipment, procedure and results of the noise surveys, as well as the active noise control experiments.

Jan 1, 2005

By R. Bhaskar

The results of an experimental study on the dispersion and deposition characteristics of fine coal dust in mine airways are presented. Experiments were conducted at various flow velocities using bituminous and semi-anthracite-coal dust which had a large proportion of dust in the respirable size range. Cross sectional variations in the concentration of dust at various points in the airway were also measured. Instruments used in the experiments included gravimetric samplers and impactors. Concentration measurements were made both for the respirable and total airborne dust. The experimental design, sampling procedures and results are discussed. The study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground mine airways.

Jan 1, 1986

By Haydn H. Murray

The area from Ohio on the east, Tennessee on the south, and Minnesota on the west: contains some very unique and useful clay deposits. Included are fireclays and plastic clays in Ohio, Kentucky, Indiana, Illinois, and Missouri; flint clays in Kentucky and Missouri; ball clays in Kentuckv and Tennessee; adsorbent clays (fuller's earth) in Missouri, southern Illinois, and Tennessee; and alluvial clays and shales for structural clay products from every state. Unique kaolin clays are known in Minnesota, Missouri, and southern Illinois and halloy-site localities are known in southern Indiana. The geology, physical properties, and uses or potential uses of these midwestern clays are described.

Jan 1, 1980

By James D. Reilly

The time-worn adage "an ounce of prevention is worth a pound of cure" was never more applicable than when used in reference to coal mine safety. Many individuals have dedicated many hours to developing effective accident prevention programs, and much has been accomplished. Each production escalation, however, creates new hazards and safety problems which need special study and research. It is a never ending cyle. To study the progress of coal-mine safety is to raise memories of many individuals who have been dedicated to removing the hazards that have developed with increased productivity and deeper penetration into the earth for coal. Some vivid examples of this dedication are the works of the men who pioneered the use of the safety lamp and the use of rock dust in mining.

Jan 1, 1968

By J. Platt

Recent EPRI research on utilities? likely strategies to reduce sulfur emissions differs sharply from policy analyses showing all- switching or all-scrubbing choices. Energy Ventures Analysis, with Stearns-Catalytic and A. T. Kearney, estimated sulfur-removal costs for scrubbing or switching at virtually all affected plants in the 31 Eastern States. Cost tradeoffs occur between $30 and $40-plus per ton FOB mine in Central Appalachia ($33-44-plus per tonne). 1/2 to 3/4 of total sulfur reductions comes from scrubbing, whose costs act as a cap on low-sulfur coal prices. In a severe environmental scenario, low- sulfur coal demand evaporates, replaced by very low-sulfur (0.7%) coal demand. Additional findings and implications of EPRI coal supply and market studies will be reviewed.

Jan 1, 1987

By H. I. Meyer

The mine is a large open-pit copper mine located near Tucson, AZ. Mining operations involve shovels digging at relatively fixed locations and haul trucks moving the muck to a primary ore crusher, a primary waste crusher, and directly to waste dumps. The total investment in shovels and trucks is some $100 million. Fig. l is a schematic drawing of the operation. A static method of truck assignment is used; i.e., each driver is given one particular shovel to serve until reassigned by the dispatcher. A dynamic system is one where trucks are reassigned after each trip. The problem is to compute a near optimum assignment of trucks for efficient operation.

Jan 1, 1979

By G. Hargrave, K. W. Moloney, M. R. Stokes

In recent years drivage advance rates in the UK have in- creased from 35m per week in the 1980's to 100/150m per week possible today. These extended rates of advance have resulted in an increase in the potential methane, dust and heat generation at the drivage face. In order to disperse this additional pollutant load requires an increase of fresh air at the face. Although advance rates have changed, current auxiliary ventilation practice has not. UK mining law requires that the fresh air must be delivered to within 5m of the face. This has lead to the wide spread use of overlap auxiliary systems, since a pure forcing system set at this distance would lead to excessive airborne dust. UK mining law does not at present consider on-board mounted exhaust scrubber fans to constitute an effective overlap fan within mechanised drivages. In an attempt to determine whether working conditions could be safely and economically improved within mechanised drivages, a series of preliminary full scale gallery trials were con- ducted. A summary of the principal findings of these trials are presented together with an outline of a series of representative CFD simulations, scale model experiments.

Jan 1, 1997

By W. F. Visser

The growing availability of information and data analysis capabilities of recent years provides new opportunities for improving the performance of mining operations. By using real-time measurements and artificial intelligence, it is possible to respond faster to changing conditions, while accurate and timely information permits rapid evaluation of changes and fast business improvement decisions. This article presents a blueprint for alignment of systems, organizational design, and management practices to leverage these developments in performance-driven operations management in mining and mineral processing. The first component of the blueprint is a performance framework with a system of key performance indicators for production control that can be used across organizational levels. This system places improvement at the core of management activities, giving greater importance to improvement skills at lower organizational levels, so companies can leverage available information for improving operational control. Secondly, the blueprint defines an organizational structure that strengthens performance improvement with technological and change management capabilities. Finally, the blueprint proposes alignment of management practices, covering the optimization of short-interval controls, the application of an improvement project portfolio management system that determines the ownership of improvement projects, and the coordination of controls across the organization. This combination of systems, organizational design, and management alignment supports rapid decision-making at the right organizational level. Introduction of the presented blueprint for operations management enables mines to leverage the developments in information and analysis capabilities to improve the performance of operations.

By R. S. Kalyoncu

Materials demands by the advancing process technologies, desire for higher performance and durability, and improved efficiency in combustion processes, such as applications in heat engines, heat exchanges, and batteries have added to the driving force fueling R&D efforts for the development of components with the combined characteristics of metals and non-metals. These new materials involve refined and specialized microstructures that can lead to improvements in the performance characteristics and durability new technological applications require. Fabrication and sintering methods, once believed to be sufficient, alone, have been found to be inadequate in the manufacture of such advanced components. Realization of the importance of the starting powders has led to efforts to produce materials of ultrahigh purity and ultrafine particle size with very narrow particle size distributions. Such powder characteristics are essential for the fabrication of components with high density and with the desired mechanical, electrical, or magnetic properties called for by the specific application. Novel ultrafine and ultrapure powder preparation techniques are discussed and effects of impurities on the powder characteristics, particle size and morphology, sintering behavior and properties of the finished product are elucidated.

Jan 1, 1992

By Douglas F. Crickmer

Pocahontas Land Corporation, a wholly-owned subsidiary of Norfolk and western Railway Company, owns a 100,000-acre block of coal lands in Martin, Johnson, Pike, Floyd and Lawrence Counties, Kentucky. These holdings were largely acquired in three major purchases between the years 1942 and 1959. The area is undeveloped and constitutes a part of the coal reserve for future mining. This block, which is principally in Martin County, lies in a triangle formed by the Levisa and Tug Forks of Big Sandy River on the sides with Dewey Dam at its base and the Town of Louisa at the apex. The topography'is typical of eastern Kentucky and consists of steep hills rising from 500 to 800 feet above creek level. There is little level ground in the area. As a matter of fact, some roads are on the creek bottoms with what little bottom land is available in the hollows being utilized for small-scale farming. The steep hills are marked by three separate massive sandstone formations which form cliffs ranging from 40 to 100 feet in height.

Jan 1, 1964

By M. A. A. de Klaver

Functional Description Figure 1 is a typical flowsheet for a system for solid fuel addition to filter cake. Solid fuel, coal, coal breeze, or charcoal, is fed from a,stockpile to a surge hopper. The solid fuel is metered into a grinding mill. The fuel is dried and ground in a grinding mill. The on-size particles are removed from the mill by air sweeping. The ground solid fuel is separated from the air stream by a cyclone and stored in a surge hopper. The ground solid fuel is then pneumatically conveyed to a small hopper in the balling area. The fuel is proportioned into the filter cake just prior to mixing. An efficient mixer is very important to have a successful operation. The exact flowsheet would depend on a number of factors including what fuel is used, how the fuel is received, and the cnaracteristics of the fuel as received. Availability of floor space in the plant may also affect the flowsheet. For example, drying air may be supplied from the pellet furnace if the grinding mill can be located near the grate, or the pneumatic conveying system and a surge hopper may be eliminated by placing the grinding mill adjacent .to the mixing area. Also, for a multiple line plant, a ball mill rather than a roller mill may be more suitable.

Jan 1, 1980

By R. K. Mehta

Conventional triboelectrification based dry coal beneficiation methods require ground coal as a prerequisite feed material, energy intensive static-in-line mixer or cyclonic tribocharger configuration, and transport and/or improvement in the design of free-fall separators to improve the separation efficiency of [me pyrite/mineral matter from coal. The proposed paper illustrates the two concepts. First, the use of ceramic media in a polyurethane lined attitor in achieving simultaneous grinding and differential charging. Second, the use of an electrocentrifuge to selectively separate coal from mineral matter present in the triboelectrified mixture. It is of interest to note that some ceramic media can satisfy the requirements of both desired density and work function to achieve grinding and differential charging.

Jan 1, 1996

By G. L. Barthauer

It is a distinct privilege to have the opportunity of addressing this group today. Although I, myself, am not a mining engineer, I have always had profound admiration and respect for those of you who each day live and work according to the tenets of Murphy's Law. Murphy, as some of you may know, was an Irish philosopher whose sole contribution to his field was the observation, "In the mining industry, if anything can possibly go wrong, it will!" You have heard this afternoon a variety of papers, touching on or describing in some detail imminent problems which presently face the coal industry. Many of these problems show no signs of diminishing. Actually, there is good reason to believe that they will intensify as governing bodies pass additional enabling legislation and regulatory agencies adopt more stringent "Rules and Regulations". In many cases, these groups are seemingly oblivious or indifferent to either cost factors or technical problems involved in achieving the desired goals.

Jan 1, 1967

By W. Dziurzynski

The present article sets forward the results of field tests that made it possible to validate the mathematical model used in the VENTGRAPH ventilation engineer programmes. The case considered relates to the introduction of a new heading to the ventilation network of the mine. The utilisation of computer programmes in practice is justified by the necessity of ensuring expected performance and secure conditions in the network of mine headings, where - for example - plans are being made to utilise the transport dip-heading, taking into consideration fire and methane hazards. In the article we have presented the methodology of preparation of a database for computer programmes of the VENTGRAPH system, obtained on the basis of ventilation measurements. The next step consists in the execution of a design of the modified network and prediction, this on the basis of heading geometries, of parameters characterising the flow of air for the designed headings. Due to the fact that the heading was in the final stage of driving, following its introduction to normal operation and the stabilisation of flow values it was possible to retake ventilation measurements, which validated the results obtained through computer simulations. In order to execute measurements of the volume flow in the dip-heading, we employed a new wireless multipoint measurement system to determine the velocity field of air in the mine heading; the results are characterised by a high accuracy of measurement. As a part of fire prevention and incident management planning, a series of underground fire case studies for the a validated network flow model has been made. Results of simulations show the capabilities of the FIRE module of the mentioned software, including assessment of stability of flow directions and hints on counter and preventive measures for particular locations of fire.

Jan 1, 2009

By James W. Bass

Introduction Atmospheric fluidized bed combustion (AFBC) is an improvement over coal-fired boiler design. It offers several advantages over conventional boilers. AFBC can meet sulfur and nitrogen oxide emission regulations without the need for add-on flue gas treatment equipment. The relatively low combustion temperature inhibits ash melting, thus reducing slagging and fouling that can in turn increase a boiler's fuel flexibility. AFBC process The fluidized bed boiler that operates at atmospheric pressure on the fire side (AFBC) is relatively simple and no different in purpose from those pulverized coal boilers used by utilities today. Fluidized bed boilers can generate steam at the pressure and temperature needed by modern steam turbines. Only the firing system is different. In fluidized bed combustion, the fuel can be almost any coal or waste fuel. It is burned in the presence of a bubbling bed of limestone. Air is forced through the bed at a velocity sufficient to support the weight of the bed particles. When the bed is fully fluidized, it bubbles like a boiling liquid. Although the burning coal makes up less than 1% of the fluidized bed, all the bed particles are heated quickly by the turbulence. The calcium in limestone reacts with sulfur dioxide produced in coal combustion to form calcium sulfate in a dry solid state. In this way, sulfur emissions regulations can be met without installing flue gas desulfurization equipment. Boiler tubes submerged in the bed absorb heat directly from the turbulent solids. The heat converts water in the tubes to steam or superheats the steam. Because of the intimate contact of the boiler tubes with the fluidized bed, heat transfer is highly efficient. Consequently, less boiler tubing surface is needed to generate the same amount of steam as in a comparable pulverized coal boiler. The optimum temperature for sulfur capture is relatively low, about 815°C (1500°F) as opposed to 1370°C (2500°F) for pulverized coal boilers. This results in the formation of lower levels of NON. Because operating temperatures are below those that fuse coal ash, a single design can burn a variety of coals without slagging or fouling problems. TVA's AFBC development program Tennessee Valley Authority's (TVA) involvement in AFBC development began in 1974 and has addressed the technical uncertainties through a comprehensive program of design, experimental, and analytical studies. In 1979, TVA and the Electric Power Research Institute (EPRI) developed plans for a 20-MW AFBC pilot plant, a 10-fold scale-up over the next largest test facility. Pilot plant design features TVA constructed the pilot plant at the Shawnee Steam Plant near

Jan 4, 1986

By W. A. Vine

Next year, in 1964, Butte will celebrate its Centennial. It was in May, 1864, that the first recorded mining activity took place. During that summer, several rich placers were found on Silver Bow Creek and its tributaries, and a gold rush followed. As placer mining proceeded in the creek beds, the quartz lodes on the hillsides were located and the veins were prospected. Mining in Butte entered its second phase when the rich silver mines, the Alice, Moulton, and Lexington, were opened. The silver boom lasted until the decline in the price of silver in the early 1890's forced the closure of many of the mines. An indication of the beginning of the copper mining era in Butte was in 1866 when it was noticed that green copper carbonate discolored some of the, lode material. It was not until ten years later, however, that the Anaconda and St. Lawrence claims were located by Michael and Ed Hickey. The claims were sold in 1880 to Marcus Daly and in 1881, Daly obtained financing and organized the Anaconda Silver Mining Company to exploit the vein The silver venture was a failure because of the predominance of copper which diluted the bullion to only 400 fine.

Jan 1, 1963

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dumper operators are frequently exposed to whole body vibration (WBV) in surface mines. Surface mining activities involve the amalgamation of comparatively high intensity of vibration and extended exposure durations. Efficient risk reduction mandates knowing of important phases of a task that poses a threat to health of dumper operators. So far in India very limited studies have been reported on WBV exposure with regard to surface mines. This paper evaluates WBV of dumper operators based on ISO 2631-1:1997 Standards and European Union (EU) Directive 2002 for different phases of job cycle. Six dumpers were considered for this study and the vibration measurements were made for all the four phases of the job cycle by placing the triaxial accelerometer on the operator’s seat-surface and at the seat-back, independently. The findings of the study revealed that the haulage task (loaded travel and empty travel) remains the chief contributor to vibration exposure according to seat-surface and seat-back measurements. Maximum frequency weighted root mean square (RMS) of 1.12 m/s2 and 1.09 m/s2 were reported for empty travel task for seat-surface and seat-back measurements, respectively. For seat-surface measurements based on RMS, Z axis remains as the dominant axis of vibration for all the dumpers during haulage task, whereas for seat-back measurements, the dominant axis varies between X and Y. Exposure action value (EAV) based on RMS has exceeded the threshold value of 0.5 m/s2 for all the dumpers during loaded travel and empty travel for seat-surface as well as for seat-back measurements.

By G. R. Doubek

Dual Tube Reverse Circulation (DTRC) drilling has been extensively used for collecting groundwater information for the dewatering program at Amax Gold Inc. Sleeper Mine. This paper presents a discuss ion of the types of data which can be collected from DTRC drilling, as well as the effect submergence has on the data. A simple low-cost method of injection testing has been developed using DTRC equipment, allowing quantitative data to be obtained from exploration or test holes. Potential yields can be determined for each drill location, allowing siting and design of production wells to be optimized.

Jan 1, 1992