Search Documents

By Kenneth M. Reim

In 1971, United States Borax & Chemical Corporation (U.S.Borax) initiated a mineral exploration program on federal lands in Southeast Alaska, with the commitment that any possible development would be done with great care for the environment. This program resulted in the discovery of a molybdenum deposit and the location of mining claims in 1974, in an area 45 miles east of Ketchikan, now called the Quartz Hill Molybdenum Project (Figure 1). At the time of this mineral discovery, the area was part of the Tongass National Forest, managed by the Forest Service, United States Department of Agriculture, and open to mineral entry and multiple use. In late 1978, the area was designated Misty Fjords National Monument and closed to mineral entry, and in late 1980 the area surrounding Quartz Hill was classified as Wilderness. These new laws and regulations, as well as the special interest environmental groups which oppose resource development, have significantly delayed and increased the costs of developing Quartz Hill.

Jan 1, 1983

By A. Noble, R. Q. Honaker, J. Werner

Recovery of rare earth elements (REE) from coal-related resources has recently received significant interest due to supply concerns and their key roles in critical industries and defense-related technologies. An integrated flowsheet consisting of sorting, crushing/grinding, physical separation, acid leaching, solvent extraction, and selective precipitation was designed to achieve continuous production of rare earth products from various coal-related resources such as coarse refuse and acid mine drainage. A pilot plant was constructed that enabled continuous testing of the circuitry on a range of different coal-based feedstocks. Despite achieving significant success in producing high-grade rare earth oxide products, low REE recovery values and high operational costs necessitated a re-evaluation of the process flowsheet. This article describes the circuitry improvements that were based on both laboratory and pilot plant test results. Roasting as a pre-leach treatment was found to significantly improve the leaching rate and overall REE recovery values. After roasting West Kentucky No. 13 and Fire Clay coal refuse materials at 600 °C, REE recovery increased by 60 and 40 absolute percentage points, respectively. Rare earth concentration in the pregnant leachate solution (PLS) was increased to around 700 ppm prior to solvent extraction using a staged precipitation method. REEs in the precipitate were re-dissolved, purified, and extracted from the PLS using solvent extraction and selective precipitation to values of around 80%. As a result of the improvements, chemical consumption in the acid leaching and solvent extraction processes was significantly reduced. A techno-economical assessment of the improved flowsheet indicated significant commercialization potential.

By P. T. Bissert, L. Yan, J. R. Srednicki, J. A. Yonkey

"Refuge alternatives (RAs) are required in underground coal mines to support life post-disaster. RAs are mandated by MSHA to maintain an apparent temperature (AT) at or below 95°F (35°C) while providing a safe and livable shelter for a minimum of 96 hours. Because strata composition and mine temperatures will affect the final AT within an occupied RA, NIOSH researchers have collaborated with five underground coal mines across the US to characterize the effects of geographic location and seasonal temperature fluctuations on mine air temperature, relative humidity, and mine strata temperatures. The data collected indicates that some mines will experience greater temperature fluctuations than others, based on geographic location. The mine which demonstrated the greatest temperature differential over the course of the year resulted in a mine air temperature that ranged from 53.4°F (11.9°C) to 84.2°F (29.0°C) and a rib surface temperature that ranged from 55.4°F (13.0°C) to 82.8°F (28.2°C). This data suggests that the location and seasonal peak temperature can significantly affect the mine strata temperature, which could lead to a fully occupied RA exceeding the 95°F (35°C) AT limit over the course of 96 hours. The data reported in this paper could be used to examine the heat buildup inside an RA for actual mine conditions. Thermal simulations could be implemented to evaluate maximum occupancy ratings based on actual mine temperatures and strata compositions. INTRODUCTION In the event of a mine disaster, miners’ primary focus is to escape. Should their attempt be futile, they can enter a refuge alternative (RA) to await rescue. In 2008, the Mine Safety and Health Administration (MSHA) mandated that underground coal mines implement RAs within 1,000 ft (304.8 m) of the working face and spaced within one-hour travel distances in outby areas where persons work such that persons in outby areas are never more than than a 30-minute travel distance from an RA or safe exit. These RAs are required to provide a safe and habitable shelter for a minimum of 96 hours and to prevent the apparent temperature (AT) from exceeding 95°F (35°C) [1]. There is concern throughout the industry that in some cases the internal ambient of occupied RAs may exceed the 95°F (35°C) AT limit due to the potentially hot mine atmosphere as well as the metabolic heat generated by RA occupants and the carbon dioxide scrubbing system. The National Institute for Occupational Safety and Health (NIOSH) has conducted tests in its Safety Research Coal Mine (SRCM) and its Experimental Mine (EM) to investigate heat buildup in RAs. It was found that the number of occupants in an RA may need to be reduced based on the ambient mine temperature, which varies from mine to mine [2]. Further testing and analyses were completed to evaluate the mechanisms (conduction, convection, radiation) by which heat is transferred from an RA to the mine surroundings. Additionally, the effects of varying mine strata compositions on the heat buildup inside an RA were studied [3]. The mine strata temperatures will increase due to heat transfer from within an RA. Depending on the mine strata composition, some mines may be more thermally conductive than others. For example, sandstone is much more conductive than shale or coal (i.e. it disippates heat at a quicker rate). All things being equal, the air temperature inside of an RA after 96 hours will be higher for a mine with strata that has low thermal conductivity compared to a mine with high thermal conductivity."

Jan 1, 2017

By Martin C. Kuhn

The use of tritium in manufacturing and its subsequent loss to the local environment in Tucson, Arizona resulted in a great debate relative to the physiological effects of low level radiation. This paper reviews some of the facts of the release and attempts to quantify the degree of hazard encountered by the local community. Some of the difficulties in assessing the true degree of absorbed dose and the assumptions necessary for calculation purposes are presented.

Jan 1, 1981

By Bahaa Alyosif, Murat Erdemoğlu, Muhammet Kürşat Aydemir, Turan Uysal

The effect of intensive milling on the conversion of microcline ( KAlSi3O8) to potassium chloride (KCl) occurred during the chlorination roasting process for artificial KCl production was investigated. A feldspar ore with 10.89% K2O grade and containing microcline was dry milled by a planetary ball mill for mechanical activation. Milled ore mixed with calcium chloride was roasted at temperatures between 500 and 1000 °C to get the chlorination roasting process. The product was then leached in water to dissolve KCl occurring during the roasting, which will be precipitated from the pregnant leach solution by evaporation. Results showed that potassium recovery from the unmilled ore increased rapidly up to 800 °C, and dramatically decreased at higher temperatures due to the removal of KCl from the furnace by means of evaporation. A potassium recovery of 31.95% was achieved by the unmilled ore, whereas it was 88.43% when 15 min milled ore was roasted at 750 °C. It was concluded that intensive milling caused mechanical activation of microcline to reduce the roasting temperature of the chlorination roasting process.

May 31, 2023

By James E. Breland

Society's growing concern over the number of deaths and serious injuries occurring in coal mines, coupled with a growing sentiment to develop and promulgate improved mandatory health or safety standards, was no doubt the basis for passage by Congress of the Federal Coal Mine Health and Safety Act of 1969, being Public Law 91-173 approved December 30, 1969. Even prior to passage of the Act, strong reaction was quick to arise concerning the effect of such legislation upon the coal mining industry. Initial response varied from mild forms of criticism to' the expressed fear of complete suspension of operations and mine closings. Primarily responsible for these early forms of skepticism were speculative or fanciful cost estimates which led operators to contemplate a less than prosperous existence. However, in spite of this unfavorable outlook, the majority of the operators have faced up to the situation and have been striving to comply with the Act and the regulations issued thereunder. While encouraging strides have been made toward implementation of the Act, it must be recognized that noticeable results have been attained only through many months of determined effort and, as anticipated, at quite heavy expense to the operator.

Jan 1, 1973

By A. M. El Shafey, Ahmed W. Hussein, Ibrahim M. Gaafar, Mona M. Fawzy, Mohamed Diab, Mohamed S. Abu El Ghar

The Quaternary stream sediments of the Diit area, southern Red Sea coast, Egypt, were mineralogically studied for their content of economic heavy minerals. The study area covered approximately 450 km2 and included three main parts: Wadi and Delta Diit, as well as Diit lens. The mineralogical investigation revealed that these sediments contain considerable amounts of placer ilmenite, magnetite, zircon, sphene, apatite, garnet, and rutile. Also present, in minor or trace amounts, are uranothorite, monazite, xenotime, fergusonite, khatyrkite, and gold. The magnetic fractionation tests, supplemented with the XRD and SEM mineral analyses, indicated the presence of Fe-oxide minerals as wuestite, hematite, and maghemite accompanied with magnetite as products for hand magnet separation. Ilmenite separation was carried out using a high intensity magnetic separator at a current of 1 A, while the paramagnetic minerals (e.g., garnet, pyroxene, amphibole, epidote, monazite, xenotime, and fergusonite) were separated as magnetic fraction at a current of 3 A. The non-magnetic minerals (e.g., zircon, apatite and rutile, uranophane, uranothorite, gold, and khatyrkite) were obtained at 3 A current. On a mineralogical and geochemical basis, the present work suggests that Diit stream sediments should be considered as a potential source for Ti, Fe, Zr, Zn, and Cu after the physical upgrading processes for concentrating the minerals carrying the aforementioned economic elements.

Jan 21, 2022

By N. R. Sainath

This paper discusses the results of a laboratory investigation carried out to study the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 1.5 and 4 inch diameter cores were mapped by visual inspection. The cores were stressed in a triaxial stress field representative of in situ conditions. The permeability of the samples to water was then estimated. The samples were exposed to 20 g/l sulfuric acid and the experiment repeated. The Permeability of unleached samples ranges from 10-1 to 10-19 m2 and it increases as leaching progresses. The porosity variation and the rate of recovery of copper from the specimen during leaching were also studied.

Jan 1, 1991

By Ian M. Loomis, Keith G. Wallace

The Waste Isolation Pilot Plant (WIPP) is a U.S. Department of Energy research and development facility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste. The waste storage horizon is 655 m (2150 ft) below surface in bedded salt. To date the WIPP project has not emplaced any waste. There are three intake shafts used to supply air to the underground. All air is exhausted though a single return shaft. The total design airflow during normal operations is 200 m3/s (424,000 cfm). The ventilation system is designed to provide separate air splits to construction, experimental, and storage activities. Separation is achieved by isolating the storage circuit from the construction or experimental circuits with bulkheads. Any air leakage must be towards the storage area of the facility. Field studies have shown that the pressure differential necessary to maintain the correct leakage direction is susceptible to the effects of natural ventilation; therefore, extensive studies and analyses have been conducted to quantity the natural ventilation effects on the WIPP underground airflow system. A component of this work is a monitoring system designed to measure the air properties necessary for calculation of the natural ventilation pressure (NVP). This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure at strategic locations on surface and underground. The psychrometric parameters of the air are measured every fifteen minutes. From these data, trends can be determined showing the impact of NVP on the ventilation system during diurnal variations in surface climate. Both summer and winter conditions have been studied. To the author's knowledge this is the first reported instance of automatic and continuous production of time and temperature variant NVPs. This paper describes the results of the initial monitoring study. INTRODUCTION The ventilation system at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico, is designed to perform two distinct functions. First, it supports normal mine ventilation requirements complying with all state and federal mine regulations. Second, the system is designed to prevent an uncontrolled release of radioactive contaminants from the storage and transportation areas of the facility. Although a nuclear radiation release in the facility is considered unlikely, many special features are implemented in the ventilation system to prevent the possible spread of contamination. The facility is constructed with the waste transportation and storage areas separated from the mining and non-radioactive experimental areas. The ventilation system is designed such that air leakage is from the mining and experimental areas to the storage areas. Furthermore, radiation detectors are located throughout the storage and waste transportation areas underground and an exhaust filtration building is installed on surface to prevent the possible release of radiation to the environment. For over two years the underground ventilation system has been rigorously tested and balanced. It was during this period that the adverse effects of NVP were noticed and subsequently quantified. From extensive field studies and computer models, several mitigating features were designed and constructed and special operational procedures were implemented to control the impacts of NVP. To quantify more accurately the NVP at the WIPP, a continuous monitoring system was installed. This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure every fifteen minutes at strategic locations on surface and underground. From this psychrometric data, the NVP is calculated. Fan operating pressures and flows and strategic differential pressures are recorded from the site Continuous Monitoring System (CMS). The monitoring system provides a means of evaluating how the ventilation system behaves in regard to climatic conditions and to judge the efficacy of the mitigating features and operational procedures. To the author's knowledge, continuous calculation of NVP as a function of time and surface temperature has not been previously reported. Overview of the Waste Isolation Pilot Plant The U.S. Department of Energy determined that the plastic nature of bedded salt may provide the best solution to isolate transuranic (TRU) waste from the biosphere. Initial evaluations at the WIPP site began in 1974. In 1979, the United States Congress enacted Public Law 96-164 for the construction and development of the WIPP project. The mission of the WIPP is to demonstrate the safe, long-term disposal of TRU waste generated by the national defense programs of the United States. TRU waste is classified as a low to medium level waste. The waste is stored in drums and does not produce significant heat (not greater than 1 W per drum). The WIPP site is located approximately 47 km (29 miles) east of Carlsbad, New Mexico in the Chihuahuan Desert. The repository is located in the 630 m (2000 ft) thick Salado Formation. This Permian Basin salt deposit is about 225 million years old and appears to have been minimally disturbed by earthquake, faulting, and ground water activity since it was deposited. The underground facility is 660 m

Jan 1, 1993

By Russell H. W. Chadwick

Reviewing events in the minerals industry, in economic geology, and in my own exploration work, I find that the most compelling subject for comment is the increasing ferment in ore deposits theory. New discoveries and continued investigations of bedded deposits of lead and zinc, copper, iron, uranium, etc., coupled with the availability of much new and significant data from sedimentary and metamorphic petrology, geochemistry, and oceanography, has led many economic geologists like myself to become disenchanted with former simplistic notions. Now disenchantment among serious people should presuppose both valid objections to the old, and valid new substitutes. I can sum up my own position and, I believe, what most of the recent writers on ore deposits theory are trying to tell us, by saying that a physico-chemical (bench science) approach to a natural science is neither correct nor useful, and that the obvious cure is a return to the study of the geology of ore deposits. More specifically, ore should be viewed merely as an unusual concentration produced, in stages, by the natural processes inherent in the geochemical cycle. In criticizing the conceptual basis of a science, one is involved simultaneously in the inherent character of the science, its subject matter, and the old and new concepts. I have found it impossible to make a clean separation along those lines. As a result, and as the title suggests, these are not-quite-random reflections on genesis, a matter near and dear to all true treasure hunters since Agricola.

Jan 1, 1967

By PDF

Flotation columns are widely used in mineral processing and coal preparation industry today. Mathematical modeling of flotation columns has conventionally been done using axial dispersion or tank-in-series models. However, for design and scale up purposes these models are not adequate enough because they do not provide detailed information of the flow fields within the column. This paper presents a Two-Dimensional, Two-Phase. Fluid-dynamic Model and its numerical solutions for some cases encountered in column flotation. The MAC (Marker and Cell) method was employed to obtain the numerical solutions, and based on this method a computer code COLUMNFLOW was developed. The simulated flow field reveals the presence of a circulation flow structure in flotation columns, which could be one of the main reasons for mixing in column flotation. The effects of some parameters such as superficial gas and liquid velocities on the characteristics of the flow structure in flotation columns were also tested with the numerical model.

Jan 1, 1994

By R. N. Powell

The Pipeline ore body was discovered in March 1991. The construction of the new mine and mill did not start until early March of 1996. Upon completion of permitting and corporate project approval, the 289 million USD project was “fast tracked”. The commissioning began 11 months after start of construction and the project ended 40 million USD under the budget figure. The objective of this paper is to review and highlight the Pipeline Project history from discovery, design, lawsuits, permitting, and re-design through to current - 1998operating practices. Particular emphasis will review the process design, design mistakes, and design successes. The paper will review project history, feasibility, design concepts, operator training, construction, financial and the current operation. Additional discussion will review what design features worked and which did not work within the process plant.

Jan 1, 1999

By K. Severin, B. Flanigan, P. Marion

“Plutonic-related” gold deposits in Interior and SW Alaska (Tintina Gold Belt) vary significantly in size, grade, vein/deposit morphology, depth of emplacement, distance from causative pluton and metal association. Metal associations such as Au-Bi and Au-As-(Sb-Hg) are a good empirical indicator of depth of emplacement and distance from causative pluton and have been used successfully in exploration. Results from a variety of analytical techniques also suggest a phenomenological cause for these metal associations, e.g. gold and bismuth have linked metallogenesis at high temperatures and thus are best correlated at deposits that are deep and/or close to causative intrusions.

Jan 1, 2000

By Francois E. Heuze

The mined geologic burial of high-level nuclear waste is how the favored option for disposal. The underground repositories must keep the waste away from the biosphere for very long times - several thousands to tens of thousands of years. Also, access must be maintained to the vaults for several tens of years, so that the waste can be retrieved, if necessary. Both the excavation of the underground chambers, and the radiogenic heating will disturb the rock mass. The overall rock mechanics problem is to understand and predict the processes associated with these perturbations, and their impact oh the isolation and containment of the waste (3)**. The specific rock. mechanics issues which have been identified for the three candidate hard rocks (basalt, granite, and tuff), are summarized in Table 1. The table also indicates the level of adequacy of our knowledge in the areas of the various issues. Such an evaluation is consistent with the general consensus of the rock mechanics profession, as explained in several key reports and publications (1 to 11). The main shortcomings of today's rock mechanics for waste repositories can be summarized as: ? lack of resolution for remote mapping of fractures in rock masses ? great difficulty in testing large volumes of rocks to determine their mechanical properties.

Jan 1, 1981

By J. T. Hollow

The Fort Knox Mine is located in Alaska?s interior, where the average ambient air temperatures range from -24°C (-11°F) in January to 16°C (61°F) in July. The mill processes a free-milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leaching, carbon adsorption and cyanide destruction kinetics. Additionally, an energy-balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy-balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy-balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post-project plant performance that validates the model and shows that the mine produced an additional 596 kg (19,155 oz) of gold while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By J. H. Kempton

The scrutiny given to model predictions of pit-lake water quality has focused attention on the uncertainty associated with long-term predictions. Although comparison of probabilistic predictive modeling of water quality in existing pit lakes indicates that short-term predictions can bracket most parameters, uncertainties in wall-rock reactions and the stability of groundwater composition and climate remain unquantified. This overview of the uncertainties associated with longer-term predictions is presented as support for those considering policy decisions that must be made in the absence of reliable estimates of future conditions.

Jan 1, 1998

By Isabel F. Barton, MarkD. Barton, Christian A. Rathkopf

Molybdenite is the world’s principal source of rhenium (Re), a critical element in multiple high-tech applications. However, the Re contents in molybdenite vary by orders of magnitude on scales ranging from single grains to whole deposits. In order to better understand the systematics of this variation and what geochemical factors control molybdenite Re concentration, and hence overall Re resources, we examine global patterns in molybdenite Re contents through a compilation of > 3000 measurements of Re in molybdenite from > 700 mainly ore-bearing moderate- to high-temperature hydrothermal systems of different types. Our results are similar to but expand on those of earlier studies. Rhenium concentration in molybdenite has a lognormal distribution and varies systematically with type of geologic system, intrusive lithology, and Mo grade. The lowest-Re molybdenite occurs in greisens (geometric mean 1 ppm ± a multiplicative standard deviation of 9), quartz vein-hosted W-Sn deposits (2 ± 5 ppm), unmineralized granites and granodiorites (12 ± 8 ppm), intrusion-related deposits (24 ± 8 ppm), and porphyry W-Sn deposits (16 ± 11 ppm). Rhenium is most enriched in molybdenites from volcanic sublimates (23,800 ± 5 ppm), with skarn Fe and Au (560 ± 5 ppm and 540 ± 3 ppm respectively) and porphyry Cu and Cu-Au deposits next (470 ± 4 and 430 ± 7 ppm respectively). Among porphyries, skarns, and quartz vein-hosted deposits, Re is most highly concentrated in molybdenites from Cu and Au systems and its concentration decreases systematically through Cu-Mo, Mo, Sn, and W deposits. In nearly all cases, molybdenites from systems associated with intermediate igneous rocks contain more Re than molybdenites from systems of the same type with more felsic rock associations. The disparity between Re contents of molybdenite in felsic and intermediate systems is largest for porphyries, quartz vein-hosted, and skarn deposits and is near zero for subeconomic or barren granite and granodiorite Mo systems; felsic intrusion-related deposits have slightly higher molybdenite Re than their equivalents associated with intermediate intrusions. In most systems, molybdenite Re content does not correlate with metal grade, but may have an inverse correlation with Au grade in intrusion-related deposits (based on a small number of data points) and does exhibit a strong inverse correlation with deposit Mo grade. Dilution of Re through larger amounts (higher deposit grades) of molybdenite explains about 40% of this correlation, but the relative enrichment of Re in molybdenite from low-Mo deposits must also reflect some selective enrichment of Re/Mo in porphyry Cu systems compared to porphyry Mo systems. We found no evidence for secular increase or other systematic temporal variation in molybdenite Re content. The data regarding the use of molybdenite Re content as a proxy for mantle influence are ambiguous. Nearly all observed empirical correlations can be traced back to differences in redox state and sulfide concentration, the two geochemical factors identified here and by previous experimental work as the controlling influences on Re mobility under hydrothermal conditions. Hydrothermal systems with reducing conditions (W- and Sn-rich) tend to have low molybdenite Re even though compiled whole-rock data indicate that their source rocks have as much or more Re as those of more oxidized systems (e.g., Cu-rich). Vapor-phase exsolution, crustal assimilation, and mixing with external fluids may all enrich molybdenite Re concentrations in individual deposits and deposit types, but their extent and importance in overall hydrothermal concentration of Re is uncertain. Thus, it appears that the available molybdenite Re resource in an ore deposit largely depends on how the deposit’s redox and sulfidation conditions have varied over time and space during the timespan of hydrothermal activity. Oxidized, high-sulfide conditions tend to concentrate Re in molybdenite, whereas reducing conditions tend to leave Re dispersed at low concentrations in the bulk rock.

By C. Cristoffanini

A real-time transient pipeline simulation was used to model the operational pressure response in the concentrate and tailings pipelines of the Minera Los Pelambres copper mine in Chile. A high-fidelity simulator was needed to train the operators on safe operation of the pipeline for different scenarios. A simulator that solves the transient equations was used to dynamically predict the pressure and flow throughout the pipeline to provide real-time responses to operational changes such as opening or closing a choke valve, or sending a water batch. Slurry rheological properties were incorporated into the model. This paper presents the technical background of the pipeline simulation model and the study of slurry properties. The paper shows the results of the transient simulation for different operating scenarios such as start-up, shutdown and leakage, by presenting the hydraulic gradient curves for each case. Finally, the paper briefly presents how the simulator was connected to an emulated control system and used to train the operator, it demonstrates the most effective tool available to learn to resolve undesirable conditions.

Feb 23, 2014

By Yung Sam Kim

The study of ultrasonic-wave propagation in substances has been remarkably advanced in recent years in most engineering and science fields. The main object in studying the velocity of ultrasonic-wave propagation in solids, is to determine dynamic properties of these materials. The present paper, however, presents some other possible applications of ultrasonic-wave propagation in the study of rock mechanics as follows: Investigation of the mechanism of microseismic activites of geologic materials, (a) at initial or low stress level, (b) at final or fracture stress level, and (c) under fatigue loading condition. Also, correlations among stress level, density, and the velocity of ultrasonic-wave propagation in rocks are discussed in this paper.

Jan 1, 1973

By Tim O’Neil

ISO 9000 is a system of quality standards that originated in Europe in the 1980s and has since been widely adopted by manufacturing companies throughout the world. The ISO 9000 standards have received less attention in the minerals industry. But, in part as a result of customer pressure, a trend is beginning to emerge for minerals producers to seek ISO certification. This is especially true among producers of industrial minerals. In early October 1994, SME's Industrial Minerals Division held a conference "ISO 9000 - uniting industrial mineral producers and consumers into quality partnerships," in Nashville, TN to bring people from the industry together to talk about their experiences with ISO 9000. William J. Miles, of Bentonite Corp. Inc., and A. Frank Alsobrook, of Alsobrook and Co., were cochairmen of the meeting. In his introductory remarks, Miles noted, "ISO 9000 is more than a quality program. It is a quality philosophy. Appropriately imple-mented, it is a contract between the supplier and the customer. It leads to continuous quality improvement and reduced manufacturing costs."

Jan 1, 1995