Search Documents

Water contact angles in the air/water/francolite, fuel oil/water/francolite and fuel oil/water/quartz systems were measured to describe the wetting characteristics of these minerals. It was found that white francolite is more hydrophilic than black and tan francolite both in the absence and presence of fatty acid addition. The contact angle measurement results do not correlate very well with the flotation response and it appears that kinetic aspects of the bubble attachment process play an important role in the francolite-fatty acid flotation system.

Jan 1, 1997

"The use of gas, temperature and airflow sensors to monitor mine ventilation atmospheres offers numerous safety and operational bene-fits to mines. Detection of dangerous gases, changes to airflows and temperature variations are some of the obvious benefits of using at-mospheric sensors in mines. The prediction of atmospheric conditions between sensors however is potentially difficult, and gaining full cover-age a mine will require either many sensors or a method of extrapolat-ing and predicting atmospheric conditions between and downstream from a sparser array of sensors. A dynamic simulation computer model technique is demonstrated to predict time based changes to atmosphere conditions downstream from sensors. The dynamic model predicts the time based changes to conditions throughout a mine model by simulating the mixing, addition and dilution of gases and airflow changes in incremental time steps. The advantages of this method is that a real time overview of full mine atmospheric conditions can be viewed at all locations, even areas without sensors. In addition, with careful planning and consideration of potential contaminant sources, the number of required sensors can be minimized. INTRODUCTIONMine Ventilation Sensors The importance of continuously monitoring mine atmospheres has been recognised since mining underground began and the effects of harmful gases on human health were discovered. Through the 19th and early 20th centuries, coal miners would take canaries underground with them as an early detection system against life threatening gases such as carbon dioxide, carbon monoxide and methane (Figure 1). The canary, normally a very songful bird, would become agitated, stop singing and eventually die if not removed from these gases, signalling the miners to quickly exit the mine (Davalle, 2011)."

Jan 1, 2016

By Edward K. Davison

The so-called "construction aggregates," sand and gravel, crushed stone, and several kinds of metallurgical slags, are used principally in the construction and maintenance of all kinds of roads, engineering structures, buildings, homes, airports, etc. Production of these aggregates is approaching two billion tons annually. In terms of tonnage produced, sand and gravel has been the leading mineral since 1954, with crushed stone gradually approaching an equal tonnage. Sand and gravel is of widespread occurrence and of wide variation in suitable gradation and quality. It is a low-value, heavy-loading, short-haul commodity. These characteristics account for the historic concentration of production tonnage in and near urban areas where construction activities are concentrated. The combination of improved urban and near-urban highway systems and the steadily rising rail rates for short-haul traffic has fostered a consistent change since World War II from rail to truck transport, with trucks now accounting for more than 807 of the tonnage moving away from the production sites. While there are increasing numbers of exceptions, truck transport of sand and gravel is generally limited to about 30 miles. The expansion of the urban and near-urban areas of even moderate density, which became so pronounced after World War II, has been the source of most of the sand and gravel industry's environmental difficulties. Dust, noise and truck traffic associated with the operations -- particularly truck traffic -- have, of course, generated public complaint. This has been particularly true in those many cases where housing developments have approached and even surrounded sand and gravel operations which were in operation before the development started.

Jan 1, 1974

By S. Chander

A series of nonionic and anionic surfactants were tested to enhance the flotation response of a low rank coal. An ethoxylated octyl phenol and several polypropylene polyethylene block copolymers were tested as nonionic surfactants. The anionic surfactant was a dioctyl sulfosuccinate. All the surfactants employed improved the yield significantly but the influence on grade was complex. Separate studies were conducted to determine the emulsification behavior of the surfactants. For the nonionic water soluble reagents tested, a correlation between emulsifying power of the surfactant and flotation was observed. An increase in the number of droplets produced in surfactant containing systems was considered to be the main reason for increase in the yield. Since it increased the number of collisions between dodecane droplets and coal particles. When a surfactant was introduced into the flotation pulp prior to addition of dodecane, it decreased the benefits of the surfactant significantly. The decrease was attributed to an increase in the wettability of coal and a decrease in the surfactant available for emulsification. When a suitable surfactant was added as a solution dissolved in the oily collector, a considerable increase in yield was observed.

Jan 1, 1993

In conjunction with steady increases in production levels, longwall operators have applied greater quantities of ventilating air and spray water in an effort to control respirable dust and/or methane. Air velocities greater than 7.6 m/s (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high velocities. The greatest likelihood for entraining dust into the high velocity airstream may occur as shields are advanced allowing relatively dry particles to fall from the shield canopy directly into the airstream. Laboratory tests to simulate dust liberation during shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH at velocities ranging from 2.0 to 8.2 m/s (400 to1600 fpm). Airborne dust samples were obtained with personal impactors to quantify the size distribution and concentration of the dust entrained at the various air velocities. Statistically significant increases in both total and respirable dust concentrations were measured as test air velocities were increased.

Jan 1, 2001

By L. Yan, T. Lutz, J. Noll

"Mine disasters, such as fires and explosions, can create a hazardous atmosphere due to the generation of carbon monoxide (CO). After a mine disaster, contaminated mine air can enter the refuge alternative (RA) as miners enter. Most built-in-place (BIP) RAs use an air delivery system to provide an unlimited supply of breathable air through a borehole which also serves to purge contaminants. In order to determine what levels of contaminants enter the RA, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted testing in NIOSH’s Pittsburgh Experimental Mine using groups of 5, 15, and 30 subjects entering the RA. The experiment used sulfur hexafluoride (SF6) as a tracer gas that was released into the air outside of the BIP RA to establish a uniform concentration. After the human subjects entered the BIP RA, the SF6 levels inside the RA were measured to quantify how much of the tracer gas entered the BIP RA. In tests conducted while the borehole air supply was left off as test subjects entered, interior contaminant levels were less than 3% of the exterior concentration. In tests conducted with the borehole air supply activated as test subjects entered, the interior contaminant levels were measured at less than 2% of the exterior concentration. Considering a mine disaster can result in 10,000 ppm of CO in the mine atmosphere, these percentages indicate that unhealthy CO concentrations that may lead to headaches, dizziness, and loss of judgement can occur in a BIP RA. This information will help mines make decisions concerning air locks, air delivery systems and a determination if purging mechanisms are necessary. INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and enforcement of mine safety standards (MSHA, 2006). Section 13 of the MINER Act specifically directs the National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of RAs for underground coal mines. This mandate culminated in the 2009 adoption of changes to the 30 CFR mining health and safety regulations, requiring underground coal mines to provide RAs capable of maintaining a life-sustaining environment for persons trapped underground. Such RAs can be either pre-fabricated or BIP shelters. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe, breathable atmosphere within RAs."

Jan 1, 2018

By Thomas A. Simpson

Traveling through the moors and valleys of Cornwall, England, one is reminded of the extensive mining activities of the past. Abandoned shafts, remains of granite block wheel houses and engine houses, battered brick stacks, old calciners, overgrown water wheel pits, count house remains, overgrown waste pits, and old portals are gaunt monuments to a once flourishing mining industry. Cornwall is bordered on the north by Devon and occupies the south-western most tip of Great Britain. The Atlantic Ocean borders the promontory; to the north, the mouth of the famous Bristol Channel faces the open sea; and to the south, the English Channel separates the land masses of Great Britain and Europe. This part of England is probably the most extensively mined ground in all of Europe. Such great mines as Dolcoath and Wheel Vor, Consols and South Carodan, Levant and Bottalack, remain legendary in the annals of metal mining in the nineteenth century. Many US mining districts hold close ties with Cornwall, Devon, and Wales through ancestors who emigrated from there to work in US mines in the eighteenth and early nineteenth centuries. Their descendants can be found in many major US mining districts, and their terms, expressions, customs, and methods have left an impact on the US mining scene that remains with us today.

Jan 9, 1981

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey’s test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

By Amar Prakash, V. M. S. R. Murthy, Ajoy Kumar Singh, Avinash Paul, John Loui Porathur

Weak, layered, and fragile rock mass formation, if not supported properly, is subject to roof failure thereby affecting safety and productivity in underground coal mines. Though Central Mining Research Institute – Indian School of Mines Rock Mass Rating (CMRI-ISM RMR) based well-defined support design guidelines are established, still occurrence of roof failures in underground coal mines is a real matter of concern for mining engineers and researchers. Numerical modeling techniques are successfully used by several researchers by simulating rock mass condition for stability assessment of mine openings. The analysis becomes crucial in case of weak and fragile rock formation. The present research envelops the determination of 31 cases of rock load by CMRI-ISM RMR under different geo-mining conditions followed by the development of modified Rock Mass Rating (RMR), i.e., rock mass rating dynamic ( RMRdyn) by incorporating P-wave velocity as a new parameter. The rock load determined using RMRdyn and numerical models was correlated and found in close agreement. In addition, the deviation in rock load determined by all the three approaches, i.e., CMRI-ISM RMR, numerical modeling, and RMRdyn, was compared with the actual field data. The percentage deviation obtained in RMRdyn and numerical modeling is less compared to CMRI-ISM RMR.

Sep 1, 2023

By P. Pages, J. Lombard, F. Fagnant, G. Bresson

This study is devoted to the improvement of the decision-making process in occupational protection of uranium miners in France. Its purpose is to apply the principles which are recommended by the I.C.R.P. in the field of radiation hazards. These principles, which have introduced the notion of "optimization" in standard setting, suggest the importance of applying cost-benefit and cost-effectiveness analysis to this sector. The objectives here are twofold : to evaluate the present organization of radiation protection on the basis of a simulation model of polluted air flow in the mine (due to the decay of a radioactive gas, radon) and to develop cost-effectiveness analysis of the various radiation protection policies.

Jan 1, 1981

By Halter L. Gould

Since the turn of the century there has been a marked increase in population, industrial and economic growth, and in energy requirements in the United States. During this time our energy needs have been met largely by natural gas and petroleum, but as our reserves of these materials are depleted, we are going to depend more and more on our large reserves of coal. The mining of coal for electrical power production has increased at a rapid rate during the past decade. Over half the coal produced in the United States in 1971 came from mines utilizing surface mining operations (Paone, et al, 1974). Surface mining is expected to increase as the rising cost of oil places more demand on coal for energy. About 57 percent of the coal reserves in the United States lie in the area west of the 100th meridian. About one-quarter of this can be mined by current surface methods. This would involve the disturbance of approximately 1.5 million acres (600,000 hectares). By the year 2000, projections indicate disturbance of about 200,000 acres, or 300 square miles, in the West. Mined areas receiving more than 250 mm of annual precipitation can usually be revegetated without irrigation if the spoils are properly shaped, the surface layer consists of suitable plant growth media, and proven techniques in rehabilitating disturbed rangeland are applied. Areas receiving less than 250 mm of annual rainfall or with high evapotranspiration rates pose a more difficult problem. Revegetation of these areas can probably be accomplished only with major inputs of water and good management (National Academy of Science, 1974).

Jan 1, 1978

By Martha Gross, Amanda Wachenfeld, Brian Keaney, Jean-Michel Charpentier, Frank Perrone

The Hampton Roads Bridge-Tunnel (HRBT) Expansion widens the existing four-lane bridgetunnel corridor to eight lanes through construction of two parallel tunnels, interstate widening, and bridge expansions. As part of the design-build contract, a supplemental geotechnical investigation was completed to support the design. The investigation for the subaqueous tunnel segment consisted of over 48,400 linear feet of drilling and 7,100 laboratory tests. This paper discusses the challenges of planning and executing a large-scale geotechnical investigation for underground works in a marine environment and the use of big data for effectively managing, interpreting, and transmitting data to the design-builder consistently throughout the investigation.

Jun 23, 2024

By W. Dan Hausel

In previous reports by Hausel et. al., (1979 a, b, and c), Leighton and McCallum (1979), and McCallum (1974;1979), several exploration procedures were examined as to their effectiveness in locating kimberlite intrusives in northern Colorado and southeastern Wyoming, where approximately 90 kimberlites have been recognized within 5 districts (Figure I). Briefly, geological mapping and stream sediment sampling for indic- ative heavy minerals of kimberlite (pyrope garnet, chrome diopside, and magnesian ilmenite) proved to be the two most effective methods in isolating kimberlite occurrences within the granitic terrain of Colorado and Wyoming (Hausel et. al., 1979 a, b, and c; Leighton and McCallum, 1979). Where a kimberlite intrusive is deeply weathered, remote sensing using color and color infrared aerial photography may be a potential reconnaissance tool in kimberlite exploration. The kimberlitic eluvium supports thicker grassy vegetation, and at least one species of grass (the Bluebunch Wheatgrass) is found to grow only within the eluvium. The result is that vegetation in the kimberlitic eluvium is a better infrared reflector than the vegetation in the surrounding granitic soils (Hausel et. al., 1979 b; McCallum, 1974

Jan 1, 1980

By Fengyu Ren, Kunpeng Yu, Gideon Chitomb, Qiangqiang Gao, Liqiang Ma, Jiangtao Zhai, Ichhuy Ngo

The penetration of rock fragments of overlying strata causes advanced ore dilution during drawing. The results of numerical and physical experiments showed that the proposed numerical simulation was applicable and the microscopic parameters of the model were reliable. The penetration under the variables of particle diameter ratio, density ratio, overlying strata thickness, and particle morphology was clarified. The penetration was quantitatively characterized by the discharge amount and the dilution rate. The experimental results showed that the diameter ratio and density ratio had a significant influence on the penetration. On the irregular shape of particles, the penetration is weakened. The overlying strata thickness had little effect on the penetration. This study could provide a theoretical basis for the full section uniform drawing, avoiding advanced ore dilution and further optimization of recovery rate.

Nov 13, 2023

By David L. Durler

In-situ uranium mining is a relatively new and innovative method utilized for the commercial extraction of uranium. As with any mining method, however, significant environmental concerns will be evident and must be addressed in a rational and far-sighted manner. Experience has shown that radiological and non-radiological environmental problems may not manifest themselves until after the in-situ methodology has become established and matured to some degree. It is important, therefore, to recognize potential environmental concerns and incorporate them into an environmental program that spans the premining, mining, and post-mining phases of an in-situ operation.

Jan 1, 1982

By Roland Froidevaux

The potential use of geostatistics for quantitative ore reserve reporting is shown using a simple gold case study as an example. The need of defining quantitative class limits is stressed, and a possible approach to this problem is suggested.

Jan 1, 1983

By R. Hogg

A standard procedure for determining size-specific gravity distributions of fine coal (including the -400 mesh fractions) by sieving and centrifugal sink-float separation is described. The significance of using a centrifugal sink-float technique and the effect of the magnitude of the centrifugal force on the separation of fine coal are confirmed in the present study. The relative merits of cumulative versus incremental sink-float are discussed. The procedure is evaluated quantitatively using data obtained for the products of froth flotation of -100 mesh coal.

Jan 1, 1994

By M. H. Morcali

Pistachio nut shells, an agricultural waste biomass, and Lewatit TP 214, a commercial sorbent, were investigated as adsorbents for the adsorption of platinum from dilute hexachloroplatinic acid solutions. Before the pistachio nut shells were carbonized, adsorption percentage was 65%, whereas Lewatit TP 214 ensured almost 100% adsorption. However, after the pistachio nut shell was carbonized at 1,000° C under an argon atmosphere, the platinum adsorption (%) increased two-fold. The effects of such parameters as sorbent dosage, contact time, temperature and solution pH on adsorption were studied in detail in batch mode. The adsorption equilibrium data were best fitted with the Langmuir isotherm model. The maximum adsorption capacities, Qmax, at 25° C were found to be 38.31 and 33.22 mg/g for the carbonized pistachio nut shell and Lewatit TP 214, respectively. The adsorption of platinum on both sorbents was found to be described by the pseudo-second-order kinetic model. The results indicated that the activated carbon prepared from pistachio nut shells can be effectively used for the removal of platinum from acidic solutions.

By D. Hodouin

Abstract. Dynamic experiments were performed in a continuous open-circuit 40x40 cm ball mill using a pseudo-random binary sequence of the feed rate and measuring the variations of the discharge particle-size distribution. The impulse response is calculated by a cross-correlation technique. Then a model involving a discrete transfer function and a time-series stochastic equation is calibrated using maximum likelihood methods. Based on this empirical model. a minimum variance controller with constrained input is designed and its performances are compared. by simulation, to the performances of a conventional PID regulator.

Jan 1, 1987

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and Mineral Processing Systems (MPSI) merged, a unique opportunity occurred for two independent mill fabricators to compare design pro¬cedures and the research upon which they were based. Several semiautogenuous (SAG) mill analyses are compared using Boliden Allis and MPSI methods. The differences and similarities are then used in a correlation of critical stress definitions and the acceptable design and inspection criteria. Given the opportunity to compare the total philosophies and methods of several companies involved in the design and fabrication of grinding mills, it was important to first develop the comparison method and ground rules. One option was to compare analytical methods by details such as numerical techniques and accuracies. However, this option was discarded in favor of a more general approach. The question that was finally posed was in two parts. Given an identical mill requirement: • What would be the difference in the analytical design result, and to what aspect of the analytical process could this difference be attributed? • What would be the difference in approaches to obtaining the final hardware in subcontracting, both in specifying and Quality Assurance surveillance? By using this comparative approach, questions of relative conservativeness and reliability would automatically be answered.

Jan 1, 1992