Search Documents

By C. Maltesh

Anionic conditioning of phosphate ores prior to fatty acid flotation is a very critical step that determines the eventual selectivity, recovery and hence the economics of the process. However the chemical mechanisms operating during this conditioning step are not established. Several studies have been conducted in the past to determine the mode of interaction of collectors with the phosphate fractions however these have been done on a laboratory scale using pure phosphate minerals. In order to test the relevance of the observed effects to plant practice in this work a comprehensive survey of plant practice was first conducted and then adsorption on flotation feed and francolite were studied under simulated plant conditions. Effects of conditioning energy and water chemistry as well as solids loading and fuel oil were determined. Most importantly, different adsorption mechanisms were found to be dominant under laboratory and plant conditions. In plant water, there was some physisorption of oleic acid on phosphate flotation feed and francolite in addition to chemisorption. However, in distilled water under laboratory conditions only chemisorption was detected. Fuel oil reduced the residual oleic acid in solution after adsorption, which explains the beneficial role of extender in phosphate flotation. The dissolved species in solution arising from the flotation feed or plant processing water are shown to clearly play a major role in determining the adsorption of oleic acid on the substrates. The study also specifically demonstrates the importance of conducting research tests under plant mixing conditions and plant water chemistry for the results to be useful commercially.

Jan 1, 1996

By T. Qiu

"The purpose of this study is to investigate the effect of the dosage of sodium hypochlorite as activator on the flotations of depressed marmatite and depressed chalcopyrite, with a focus on activation-flotation kinetics. Four flotation kinetic models were applied to test data using 1stOpt statistical analysis software to estimate the relationships between the maximum flotation recovery rates for the depressed marmatite and depressed chalcopyrite, the flotation rate constants and the sodium hypochlorite dosages. Within the range investigated, the highest flotation performances of depressed marmatite and depressed chalcopyrite were obtained at 2.5 mL/L sodium hypochlorite with zinc recovery rate of 93.8 percent and 3 mL/L sodium hypochlorite with copper recovery rate of 94.6 percent, respectively, after four minutes of flotation. A second-order model with rectangular distribution of flotabilities gave the best fit to test data collected at various sodium hypochlorite dosages. For the highest flotation performances of depressed marmatite and depressed chalcopyrite, the respective equations of their flotation models were derived and presented.IntroductionCyanidation tailings are the solid residues generated by gold plants that use cyanide to extract gold (Lv, Ding and Qian, 2015; Zhang, Li and Yu, 2013). Because of increasing demand for gold, the Chinese gold industry has developed rapidly, with production amounting to 451.799 tons in 2014, an increase of 5.5 percent from 2013. Chinese gold production has been the highest in the world for eight consecutive years. As a result, more than 2.45 million tons of cyanidation tailings are estimated to be discharged into tailings ponds every year (Li et al., 2010; Lv, Ding and Qian et al., 2015; Wang et al., 2015; Zhang, Li and Yu, 2013; Zhang, Li and Yu, 2012), and approximately 300 million tons of cyanide tailings are stockpiled in China, with the potential to cause serious environmental pollution as well as death to wildlife (Adams and Lloyd, 2008; Donato et al., 2007; Hewitt, Breuer and Jeffery, 2012; Velasquez-Lopez et al., 2011; Stephen et al., 2009; Zagury, Oudjehani and Deschenes, 2004). Concerns over cyanidation tailings are not exclusively environmental but also economic, as tailings occupy considerable land area, and tailings storage facilities increase the production costs of gold enterprises (Donato et al., 2007). Tailings often contain other valuable metals such as zinc, lead and copper. For example, the cyanidation tailings of Gaoyao Hetai Gold Plant in Guangdong Province contain 2.5 percent copper (Cu), 0.31 percent lead (Pb), 0.23 percent zinc (Zn) and 15.36 percent iron (Fe) (Shi, 2008), and the tailings of Tianshui Gold Plant in Gansu Province contain 1.94 percent Cu, 5.96 percent Pb, 0.27 percent Zn and 24.62 percent Fe. Cyanidation tailings have therefore been increasingly viewed as a secondary resource rather than waste."

Jan 1, 2016

By K. Hanumantha Rao, A. Javadi Nooshabadi

"Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by chalcopyrite (CuFeS2), which is a copper iron sulfide mineral, during grinding, was investigated. It was observed that chalcopyrite generated H2O2 in pulp liquid during wet grinding and also in the solids when placed in water immediately after dry grinding. The generation of H2O2 during either wet or dry grinding was thought to be due to a reaction between chalcopyrite and water where the mineral surface is catalytically active in producing •OH free radicals by breaking down the water molecule. The effect of pH in the grinding medium or in the water in which solids are added immediately after dry grinding showed that the lower the pH value, the higher the H2O2 generation. When chalcopyrite and pyrite are mixed in different proportions, the formation of H2O2 was seen to increase with increasing pyrite fraction in the mixed composition. The results of H2O2 formation in pulp liquid of chalcopyrite and together with pyrite at different experimental conditions have been explained by Eh-pH diagrams of these minerals. This study highlights the necessity of revisiting the electrochemical and/or galvanic interaction mechanisms between the chalcopyrite and pyrite in terms of their flotation behavior.IntroductionHydrogen peroxide causes nonselective oxidation of sulfide minerals if present in pulp liquid. Oxidation of sulfide minerals takes place when they are exposed to atmosphere and during the grinding process when the particle size is reduced for flotation. The oxidation of chalcopyrite leads to iron dissolution from the particle surface and from a metal-deficient, sulfur-rich surface (Fairthorne et al., 1997). Other studies report the formation of iron hydroxide on the surface with the metal ion dislodged on the surface (Buckley and Woods, 1984; Chander, 1991). The chemical reactions for the oxidation of chalcopyrite in alkaline and in acidic solutions with the addition of oxidants, such as oxygen or hydrogen peroxide, are shown in Eqs. (1) and (2), respectively (Shi and Fornasiero, 2010)."

Jan 1, 2015

By Thomas C. Shapiro

This is the final article in a three-part series on microcomputers and application software in the mineral industry. The first article covered microcomputer terms and concepts. The second discussed exploration and mining software. This article will examine plant, administrative, and geotechnical software. Every effort has been made to be current in the latest software developments. Rapid change, however, is a fact of life in the computer world and any omission is inadvertent. Introduction Geotechnical disciplines have received considerable attention in software programming. Calculations are repetitive and the formulas needed to solve them are not extremely complicated. These programs are ideally suited to the microcomputer and the microcomputer is ideally suited to the consulting geologist or engineer, due to its low cost and reliability. In fact, the advent of the Apple (a registered trademark of Apple Computer Inc.) and, more recently, the IBM personal computer has caused an explosion of inexpensive software programs available to the microcomputing public. Another area that has benefited from computerization, although not in the same way, has been mineral beneficiation. Here, process control for start-up or phase-down operations has been used in newer plants for some time. Programs to perform various calculations are becoming more common as micros increase in number. Tappi Journal has a section with solutions to handheld-calculator and microcomputer problems. Process Modeling Most process modeling is still done only on mainframes. One such program is called ASPEN PLUS (a registered trademark of Aspen Technology), and a one-week course is recommended so the user can best use the program. This program is available through timesharing from University Computing Co. Programs to find an optimal solution using Linear Programming (LP) have been around for some time. Also, plant process simulation has been possible using simulation programs. Both simulation and LP are expensive to program and run. Although there are LP programs available for some micros, the user must be fairly knowledgeable about how to set up the problem. This is because each problem must be set up as a unique program that typically requires custom programming. There are some programs that can handle blending of mine crudes and examine economic parameters over the life of the mine. Plant Applications Areas relating to mine and plant applications with programs available for micros are maintenance, production reporting, inventory, accounting, and personnel scheduling. Maintenance Maintenance typically requires that certain jobs be performed in a particular sequence and parts be ordered with enough lead time for maintenance to take place on time. There is, therefore, a critical sequence of tasks that must be performed or the scheduled maintenance will not take place. Two answers needed for maintenance project scheduling are: what is the lead time needed

Jan 4, 1984

By Galen G. Waddell

Several years of rock-burst research conducted by the Federal Bureau of Mines, in cooperation with the mining companies of the Coeur d?Alene Mining District, Idaho, in addition to progress made by others throughout the world, have led to a good understanding of the rock-burst problem. This paper describes conditions which have caused specific bursts, present capabilities of detecting stress buildup and bursts, control methods, and a suggested approach to analyzing any individual mine-burst problem.

Jan 1, 1970

By Carlton H. Baab

In June, 1981 the Electric Power Research Institute (EPRI) issued a report titled "Control Systems in Coal Preparation Plants" to determine the status of instrumentation and automation systems in the coal preparation industry. EPRI concluded that the control systems presently being employed in the U.S. coal preparation plants "are relatively primitive compared with those in other mineral processing industries; and analytical instrumentation is virtually non-existent". Until recently, clean coal has had a low selling price and satisfying the purchasers' specifications required only minimum cleaning. However, it is becoming more apparent that the increases in coalfired utility power plants forced outage rates are relative to the deterioration in the quality of fired coal. Utility companies are becoming aware of the economic value of reducing the variability of ash, moisture and sulfur in steam coal purchase orders. New contracts are currently being negotiated between electric utilities and coal producers that include provisions for increased penalties if the product does not meet specifications. With tighter specifications on the quality of steam coal, interest is increasing in more sophisticated control systems. One type of device that is currently assisting the preparation plant operator optimize and control the coal cleaning process is nuclear based instrumentation. Nuclear instrumentation includes methods for measuring weight, level, and density as well as for performing elemental analysis on coal. This paper discusses the various types and applications of nuclear instrumentation currently in use in the coal preparation industry.

Jan 1, 1983

By S. H. Amini, A. Noble

"While many classic mineral processing circuit design approaches rely on deterministic methods, numerous studies have shown that the uncertainty inherent to the various input parameters can significantly influence design decisions. In a separation circuit, many of the technical uncertainties can be mathematically represented as statistical distributions for the unit recovery and feed grade. These uncertainties are then propagated by the circuit design and reflected in the circuit performance indicators, such as product grade and global recovery. An effective design strategy entails identifying which units are most influential in this uncertainty propagation and thus merit further consideration. Unfortunately, few analytical tools provide this information, particularly those that rely solely on deterministic methods. However, one promising approach is through the application of Taguchi’s method, in a fashion similar to statistical tolerancing of manufactured products. Since the technical challenges are fundamentally similar, Taguchi’s method shows promise in evaluating the level of compounded uncertainty by various circuit designs while determining the role of each separation stage on the overall selectivity and variability of separation circuits. This paper demonstrates Taguchi’s method in several two and three unit circuit designs. INTRODUCTION AND METHOD DESCRIPTION Uncertainty in Mineral Processing Circuit Design Analysis and estimation of uncertainty propagation in mineral processing separation circuits is an essential and significant aspect of an optimal circuit design procedure. Most of the current circuit design methodologies have been constructed, implemented, and validated using a deterministic modeling approach. However, numerous studies have shown that the inherent uncertainty induced by uncertain design parameters can be a significant factor in many mineral processing applications (e.g. Kraslawski 1989; Xiao and Vien 2003; Ghaffari et al. 2012). Thus, an effective circuit design methodology must be able to quantify uncertainty in separation circuits with limited input data. This paper describes Taguchi’s method, as an experimental design technique, to approximate uncertainty in mineral processing applications, and then the similarity of results between Taguchi’s method and Monte Carlo Simulation is investigated. Monte Carlo Simulation The term “Monte Carlo Simulation” has been used to refer to a variety of stochastic simulation methods spanning a broad array of business, technical, and scientific domains. Most generally, Monte Carlo Simulation refers to numerical analysis which is based on (pseudo) random sampling from a domain of input parameters with a known statistical distribution. This methodology allows one to determine the distribution of expected results from a standard deterministic process model. Execution of a Monte Carlo simulation begins by identifying the domain of input parameters, statistical distributions for each parameter, and a deterministic process model which describes the anticipated result as a function of the inputs. Next, one discrete random sample is taken for each input parameter, considering the input distributions. The process model is then solved for this mix of input parameters, producing a single simulation result. This procedure is then repeated a “large” number of times, utilizing new randomly sampled input parameters for each simulation iteration. Once the desired number of iterations is reached, the results of each independent simulation are aggregated to produce descriptive statistics such as minimum, maximum, mean, standard deviation, kurtosis, and other distribution parameters. Given enough iterations, the Monte Carlo method fully explores potential synergies between the input parameters. The methodology does not require the process model to be differentiable, continuous, or even analytically defined. While the number of required iterations varies in relation to th"

Jan 1, 2017

By Nick Salisbury, Alan Howard, Scott Tunison

INTRODUCTION Geotechnical investigations for tunneling projects typically use vertical test borings and, to a lesser extent, angled borings. Horizontal drilling applications were often limited to specialty testing programs and to perform probe drilling from a tunnel boring machine (TBM) as part of production tunneling. The former often involved cumbersome setups with skid rigs and cribbing in a pilot tunnel or shaft. The latter usually was limited to generic probing for rock quality and ground water conditions with no sampling. Neither yielded continuous core at production rates suitable for design and construction planning. Conventional vertical investigations still make sense in many instances, particularly for tunnels planned beneath urban settings where truck access is convenient and where the tunnel horizon is not readily accessible via a portal or shaft. However, equipment is presently available to conduct horizontal geotechnicall investigations at reasonable production rates and cost. Advantages include continuously sampling the tunneling horizon and minimizing “access drilling” to get the zone of interest at the underground construction horizon. Horizontal boring lengths of up to approximately 800 m are considered feasible and those in the range of 150 to300 m are now routine. These capabilities make horizontal borings an attractive option to consider when looking at deep tunnels beneath ridges, especially where access is limited. Fewer drilling staging sites can also mean reduced environmental impacts when investigating tunnels proposed beneath sensitive lands such as public wilderness areas. Investment in early construction packages to develop portals for investigation access and, possibly in excavating test shafts for the same purpose should even be considered. Potential benefits in the form of achieving improved overall project costs using horizontal borings exist because of the significant additional data collected in the tunnel horizon. For this reason they should be considered during the routine cost-benefit analyses generally conducted for planning geotechnical investigations for tunneling. The authors also believe that collection of such data will reduce Geotechnical Baseline Report (GBR) conservatism and lead to lower potential for

Jan 1, 2005

By J. Davies

This paper describes the successful management and construction of the 5.18 m (17 ft) diameter, segmentally lined, North Dorchester Bay CSO storage tunnel in Boston, MA. This 3,300 m (10,830 ft) long tunnel was mined through variable soft ground with only 6 m (20 ft) of cover, using an earth pressure balance tunnel boring machine. These extensive data collected from the projects unique automated and internet accessible geotechnical and TBM monitoring system, will be examined and used to explore the relationships between geological conditions, TBM operating parameters and measured settlements. The paper will also discuss the use of screw revolutions as an indicator of muck volume.

By John A. Breslin

The year 2010 will mark the 100th anniversary of the beginning of the research efforts by the U.S. government to improve the health and safety of miners working in the United States. This research began in 1910 with the establishment of the U.S. Bureau of Mines (the Bureau) and it has continued during the past 10 decades, even after the closure of the Bureau in 1996. The research on safer mining technology, formerly done by the Bureau, has now been combined with National Institute for Occupational Safety and Health (NIOSH) studies of miners? health to form a unified federal research program to improve the health and safety of miners. This article describes this research and places some of the accomplishments into perspective with other activities in the U.S. Mine Safety and Health Time Line (insert).

Jan 1, 2010

By Hemant Agrawal, Arvind Kumar Mishra

Rock breakage using blasting is one of the important operations of the mining industry. The delay timing decides the initiation sequence of holes in the blasts and is a crucial factor to improve the overall blast performance. Blast-induced ground vibration is an undesired yet unavoidable outcome of blasting. Peak particle velocity (PPV) is commonly used to measure the magnitude of blast-induced ground vibration. Channelization and better utilization of explosive energy delay are provided between blast holes using initiating systems. The use of different initiation systems even on the same site results in a very significant difference in the values of PPV generated. Due to scattered delay timings of pyrotechnic detonators, the scaled distance predictor equations obtained become unreliable. The error/scatter in delay timing leads to overlapping of holes and hence increases in maximum charge per delay. In this paper, an analytical approach has been discussed to measure the overlapping of holes during blasting with initiation systems having inherent cap scatter. The analytical approach will be calculating the probable overlapping of holes due to scatter in delay timing and will help blasting engineers to understand the variation in maximum charge per delay due to pyrotechnic based initiating systems. In this study, a total number of 102 blasts were conducted using different initiation systems at two different opencast coal mine and 221 corresponding blast vibrations events were recorded.

Nov 10, 2020

By L. Wilfley, G. A. Calboreanu

"Wear resistant 25% Cr hard cast iron is a heterogeneous material containing 1,600 HV hard chromium carbides embedded into martensitic matrix. It is the most used cast alloy in wear operations of mining industry, chemical industry, fracking, etc. During the last decade the hard iron manufacturers increased wear resistance in the following ways: • Reduce / eliminate harmful retained austenite and chromium + carbon depleted areas especially within eutectic carbide cells. In Max5A the improved 25% Cr alloy brittle carbide eutectic cells are removed which increases toughness. • Delay delamination between chromium carbides and matrix particularly during sliding abrasion wear. Delamination commences at the weakest chromium carbide – matrix contact lines exposing chromium carbide to localized bending stresses which gradually chip carbides away. Once the chromium carbide base is removed accelerated wear degradation occurs. • Evenly randomize and avoid discontinuities in the chromium carbide network. When chromium carbides are perpendicularly positioned to the wear surface wear rate is minimized. On the contrary the highest wear rate takes place when 3D oriented chromium carbides are parallel with the wear surface. In this case chromium carbides cover top network discontinuities being just matrix supported which leads to rapid carbide cracking. The new hard iron discussed in this paper fulfils and exceeds the above requirements increasing the casting service life around 250% in various wear operations. Physical and mechanical properties of Max5A are compared with well manufactured Industry Standard 25% Cr hard iron. The paper presents practical accomplishments obtained in the USA, South America and India. INTRODUCTION The chemical composition of Max5A and Industry Standard 25% Cr are identical like specified by ASTM A532 Class III Type A requesting C = 2.0-3.3% and Cr = 23.0-30.0%. Manganese, silicon, nickel, molybdenum and copper contents are limited by maximum accepted quantities.[1] According to published data the eutectic chromium carbides chemical composition of 25% Cr hard iron is Cr = 54% and C = 8% which indicates strong depletion of chromium and carbon along chromium carbide - matrix interfaces. [2] The optimized Max5A microstructure has minimized retained austenite, is devoid of harmful carbide eutectic cells and has the most advantageous chromium carbide and secondary chromium carbide morphology. This favorable microstructure increases wear resistance, mechanical properties and corrosion resistance. The paper compares the Max5A microscopic features and mechanical – physical properties with similar properties of high quality Industry Standard 25% Cr."

Jan 1, 2017

By J. R. Palmes

Three coal samples, selected out of eight with well characterized surface properties, were used in flocculation tests and synthetic mixture of coal and silica was used in the selective flocculation experiments. Coal wettability and flocculant type were found to have a strong effect on the flocculation results.

Jan 1, 1993

By V. E. Housman

EPA's Mining Waste Section within the Office of Solid Waste is continuing to collect and analyze information on mining waste management practices. Starting in 1991, the Mining Waste Section has continued to conduct site visits and prepare case study reports on the waste generation and management practices of operating mines. In choosing sites to study, a reasonable attempt was made to provide diversity in mining commodity types, geographic regions, geology, climate, and environment. To date, EPA has visited the following mines: Asarco Troy (copper) in Montana, Newmont Rain in Nevada (gold), Cyprus Thompson Creek (molybdenum) in Idaho, LTV Steel (iron) in Minnesota, Phelps Dodge Morenci (copper) in Arizona, Doe Run Fletcher (lead) in Missouri, Brewer (gold) in South Carolina, IMC Four Corners (phosphate) .in Florida, Pennzoil Culberson (sulfur) in Texas, Nerco Cripple Creek (gold) in Colorado, Copper Range White Pine (copper) in Michigan, Magma San Manuel (copper) in Arizona, Colosseum (gold) in California, and several gold placer mines in Alaska, including the Valdez Creek Mine. EPA has prepared a case study report on each facility. The mine operators were provided an opportunity to comment on their respective site visit report and their comments have been included in' each respective report. These site visit reports have in turn been incorporated into technical resource documents which provide a detailed description of each mining sector. EPA is currently reviewing the technical resource documents and plans to release the documents in the Spring of 1994.

Jan 1, 1994

By Dan Brunner, Scott Thomson, Ben Lyddall, Duncan Thomson

Geosensing is used in oilfield drilling in conjunction with geophysical tools to support characterization of rock properties, geology, and reservoir conditions. This technology is now available to the mining industry and has been successfully applied to underground in-seam directional drilling in Australian coal mines for geologic exploration and methane drainage. The system utilizes a range of drill rig and wellhead mounted sensors which, combined with analytical software, produce real-time data from which 3D spatial features can be accurately modelled significantly in advance of mining. This innovation greatly expands on the information obtained from current in-seam directional drilling practices and provides for improved characterization of coal seams, including soft and weak zones, locations of geologic discontinuities, and analysis of formation flow. This paper provides a description of the geosensing system and the interpretation of actual data from long in-seam directionally drilled methane drainage boreholes at mines in Australia, and discusses how this system increases the value of directional drilling as an exploration tool for the coal mining sector, and the evaporite and hard-rock mining sectors where directional drilling is also applied.

Feb 1, 2024

By Peter Shuttleworth, Chris Fesq, Eddie Woods

Precast concrete segmental linings for tunnels have traditionally been designed with conventional steel bar reinforcement. In many cases, this has been satisfactory in service, but in others, major problems have occurred with the durability of the linings. Commonly this has resulted from corrosion of the reinforcement, mainly from chloridesin ground water, causing spalling of the concrete and leading to very expensive and disruptive repair programs. This paper discusses the relative merits of designing tunnel linings with steel fiber reinforcement to provide long-term durability, improved impact resistance and toughness for greater load capacity across joints, enhanced robustness during transportation and erection, plus improved fire resistance with the addition of polypropylene fibers. Guidance is also given in the selection of the correct fiber type, mix design and testing methods to establish the optimum dosage required and production techniques to ensure even distribution and compaction.

Jan 1, 2005

By Ted H. Eyde

The Bowie chabazite deposit has yielded the most mined tonnage of any natural zeolite deposit in the United States. Since 1962 the deposit has yielded about 12,000 tons of crude chabazite, with an estimated market value of S30 million when sold as an activated molecular -sieve product. Between 1,000 and 1,500 tons of high-purity crude lump chabazite is now produced annually by stripping and selectively mining the lower, massive, half-foot-thick, "high-grade" bed. All of the chabazite is still shipped out of State for grinding prior to extrusion and activation. Zeolite minerals were discovered at the Bowie deposit in 1875, when Oscar Lowe identified a hydrous silicate related to chabazite or stilbite from a tuff bed that cropped out in the San Simon Valley. It was not until 1959, however, that chabzite, erionite, and clinoptilolite were positively identified as the principal constituents of an altered vitric-tuff horizon that crops out in the area originally described by Lowe. Shortly after the rediscovery of zeolite minerals in the San Simon Valley, several of the major producers of synthetic zeolites acquired land positions covering the outcrops, including projected extensions, and began exploration drilling. By 1980 all of the known chabazite reserves had been acquired by five companies and two individuals. The more than 3,000 holes drilled to explore the deposit and the excellent exposures provided by the strip-mined areas indicate that the chabazite-bearing horizon (known as the marker tuff) is confined to a flat-lying lacustrine section known to the operators as the Green Lake Beds. The deposition of the parent airborne vitric ash and subsequent zeolitic alteration was controlled by many factors, including the lake-bottom topography, depth and cation content of the saline-alkaline lake water, and proximity to post-depositional erosion surfaces. Zeolitic alteration was complete when an extensive system of younger paleochannels deeply eroded the Green Lake Beds. This left only a few erosional remnants of the marker tuff and the lower "high-grade-bed" that constitute the present deposit. Both the channel gravels and the Green Lake Beds are overlain by a section of halite-bearing brown mud-stones, known as the Brown Lake Beds. The bowie chabazite deposit can be used as a model to guide the exploration and development of other zeolite deposits that formed in saline-alkaline lacustrine environments.

Jan 1, 1987

By Richard H. Olson

Talc deposits in the Precambrian of southwestern Montana (Beaverhead and Madison Counties) are unique within the U. S. A. in that large bodies of tremolite-free talc can be open-pit mined. All known deposits are in pre-Beltian dolomite units. The origin is suspected to be metasomatic, with the siliceous component having been contributed by an intrusive Precambrian granite gneiss. Precambrian deformation was extreme and is characterized by multiple periods of tight isoclinal folding and the flowage of less competent rocks, rather than by faulting. Post- Precambrian folding has been relatively negligible; the characteristic Laramide structure is block-faulting developed along northwest-southeast trends. The talc is thought to have been formed in Precambrian time; the high-angle block-faults probably have no significance with regard to the formation of the talc, but do tend to complicate mining operations. Tremolite-free talc ore bodies with horizontal widths of more than 200 feet, vertical depths of several hundreds of feet, and strike-lengths of as much as one-half mile are known in the Ruby Range and the Gravelly Range. Where dolomite is interbedded with tremolite-free talc in the Gravelly Range, the scale of this relationship permits the use of conventional open-pit mining methods with subsequent upgrading by hand-sorting techniques. Underground mining has been used in the past, but all current Montana talc-mining operations are on the surface. The hand-sorted ore, some of which is shipped overseas, is finely ground or micronized in roller mills and fluid-energy mills. The products are distributed both nationwide and abroad.

Jan 1, 1975

By John Hardy

The performance of five dense-medium washers was evaluated in four preparation plants. Three of the plants were making a two-product separation that produced a clean coal and a refuse; one plant employed dense-medium vessels in series to effect a primary and a secondary separation. The secondary drum-type washer produced a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam generation. The sharpness-of-separation was excellent for all four primary separations and the secondary separation.

Jan 1, 1966

By M. Fan, R. Letkiewicz, A. Hobert, J. Milbourne

Ultrafine copper, gold and silver minerals flotation has become increasingly important because of the rising demand for processing finely disseminated ores. This paper investigates the improved flotation of ultrafine ores from a Troilus Gold project. Troilus is primarily an Au-Cu deposit but contains minor amounts of Ag, Zn and Pb, as well as traces of Bi, Te, and Mo. As a result of ultrafine Cu-Au-Ag dissemination and associated grinding requirements, Eriez’ column/StackCell and Denver benchtop cells were utilized to optimize their respective flotation responses. Enhanced flotation results were achieved using column and StackCell technologies. KAX 51 and SPRI 206 collectors, Na2SO3, and ZnSO4 depressants were the primary reagents employed. In column/StackCell flotation of three main mineral deposit ore composites, the rougher-scavenger-cleaner circuit Cu, Au and Ag flotation recoveries were 90.4~95.8% at a copper grade of 13.6-17.4%, 87.5-95.1% at a gold grade of 101-145.9 g/t, and 88.6-91.8% at a silver grade of 62.6-251.4 g/t, respectively. The benefits of Eriez Column/StackCell flotation technologies include high flotation selectivity and increased recovery due to unique hydrodynamic designs. Specifically, the StackCell design facilitates high turbulent kinetic energy dissipation rates to improve fine particle recovery and incorporates countercurrent wash water to significantly reduce hydraulic entrainment of the finest size gangue minerals to the froth product.

Feb 1, 2023