Search Documents

By P. D. Rao

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. Coals from Usibelli Coal Mine and the Beluga coal field have a heating value of approximately 8,000 Btu/lb and 28% moisture. Hydrothermal treatment (at 275 to 352'C) of lump coal from Usibelli Coal Mine and Beluga coal field enhanced the heating value of the coal, on an equilibrium moisture basis, from 8,000 Btu/lb to nearly 12,000 Btu/lb. The product coal with high heating value and 0.2 % S is an environmentally acceptable premium fuel. The Hardgrove grindability index of the coal is greatly improved, further enhancing its value. Increase in hydrothermal drying temperature promotes vesiculation of resinite. Vitrinite reflectance increased to 0.72 and vitrinite was subjected to widespread visiculation resulting in a coke like structure indicative that the material went through the fluid stage.

Jan 1, 1991

By Weiran Zuo, Jinsheng Guo, Chun Yu, Jinyu Zhan, Bao Guo

High-precision prediction of the target minerals’ content in the feed and concentrate products is vitally important for the efficient beneficiation of mineral resources. Visible and near-infrared (NIR) spectroscopy provides a cost-effective way for online measurement of the mineral content in an industrial process. In this investigation, simulated specimens consisting of five different types of minerals that are present in the copper oxide ore, malachite, quartz, calcite, hematite, and chlorite were prepared with a variety of malachite contents, and the mixed specimens were analyzed by a visible-NIR spectrometer in an integral sphere mode. The reflectance spectrum is used as input and the malachite content as output to build the prediction model. The obtained data was modeled by support vector machines (SVM), and a Grey Wolf Optimization (GWO) is proposed with the goal of improving the prediction accuracy. The GWO algorithm has been applied to adaptively search for the best combination of featured values. After cyclic comparison, the optimal penalty factors c and g can be quickly and accurately selected. The experimental results show that the SVM model established by the GWO algorithm has a better fitting effect and smaller prediction error, compared with other models.

Aug 3, 2023

The ventilation conditions at the underground coal mines are influenced; first: by the disturbances of the natural nature (barometric pressure, methane liberation, etc.), and second: by the disturbances caused by the production process. The major goal of this study was to determine the changes of the ventilation parameters, such as the flow, pressure and methane concentration around the longwall panel, particularly, along the longwall face due to the shearer operation (motion). It is well known from the practice, that the movement of the shearer influences the ventilation parameters around the longwall panel, including the gob area. Until now, these data were gathered in a single or multiple locations at the different time. However, only the simultaneous measurements of all of these values allow seeing the time dependent interrelationships between measured parameters. To be able to show these interrelationships, special experiments, described in this paper, were carried out by the author. These experiments were prepared and executed at the BUDRYK Coal Mine in Poland. During each experiment a simultaneous measurements and monitoring of the barometric pressure, air velocity and methane concentration at the different locations along the longwall face, were performed. The investigation was possible by using a special setup of instruments with a short sampling time, i.e., within 2 seconds. The monitoring of the absolute pressure was conducted by using the digital barometer µBar, developed by EMAG, based on the SETRA pressure transducer, model 470. The velocity of air was measured using the electronic vane-anemometers, developed by IMG-PAN. The methane concentrations were measured using methanometers as the part of the EMAG automatic gas monitoring system. The investigation data confirmed that disturbances due to the operation (motion) of the shearer at the longwall face have a local character. It could be also seen that a large diameter shearer (compared to the total cross-section area available for the air flow) is acting as the piston compressing the air (the overpressure) ahead of the shearer. This fact affects the methane mixing process and flow patterns in the vicinity.

Jan 1, 2009

By Mario E. Rossi

Often geometallurgical models are prepared at various project stages from very few data and are assumed to be representative of very large tonnages. These may include recovery models; crushing and grinding parameters and models; models of concentrate grades; models of acid consumption; etc. These models commonly do not carry a measure of uncertainty or variability, and are taken at face value at the time of design and planning. This paper proposes a proactive approach to modelling variability, providing uncertainty estimates and thus allowing for risk analysis and mitigation of geometallurgical models. The variability model is built up by understanding the limitations of the pillars of a geometallurgical model: data uncertainty; geologic model uncertainty; domain definition uncertainty; and parameter estimation uncertainty. Of these factors, typically domain definition is the most significant contributor to geometallurgical model variability. First, the fundamental supports for these models are briefly discussed, with domain definition emphasized. Second, two methods for uncertainty modelling are proposed. The first, more applicable to conceptual or early-stage projects, is a simpler and more expedient alternative that provides initial assessments of variability. This is intended to aid management in decision-making related to budgeting, including further sampling and testing. The second, a block-by-block approach that allows a detailed assessment of risk for specific designs and mine plans, thus providing further opportunities for mitigation. In the example provided, emphasis is placed in communicating this variability to both management and technical personnel in the form of “measured-indicated-inferred” indicators and also block-by-block confidence intervals.

Jun 25, 2023

By M. Hakan Morcali, Onuralp Yücel, Haldun Gürcan, Serdar Aktas, Semih Özbey, Alper Keskin

"This work presents a method for the precipitation of cobalt sulfate by alcohols, specifically ethanol and methanol. The effect of the initial concentration of cobalt, the volumetric ratio of alcohol to cobalt sulfate solution, the addition of sulfuric acid and ammonia, and the effects of common ions on the precipitation percentage were investigated. The performances of ethanol and methanol were compared in terms of the precipitation percentage of cobalt sulfate, and explanations for different performances are offered. In the sulfate-based solution, the alcohol was shown to displace water ligands from the first coordination sphere of the cobalt(II) cations, which led to the precipitation of the cobalt ions as cobalt sulfate heptahydrate. SEM analysis revealed that the particle sizes of the powders produced by this method are smaller than those of commercially available cobalt sulfate. The scientific literature contains no data on the solubility of cobalt sulfate in ethanol. In this study, the solubility product constant (Ksp) for cobalt sulfate was experimentally calculated to be approximately 1.15 x 10-5.IntroductionCobalt sulfate, which is one of the most important compounds of cobalt, is used in the electroplating and electrochemical industries. The addition of cobalt sulfate to nickel-plating baths makes the treated metals brighter, harder, smoother and more ductile (Armstrong et al., 1988). It is also used as a desiccant for lithographic inks, varnishes, paints and linoleum, as well as in storage batteries, e.g., nickel-cadmium (Ni-Cd) and lithium-ion (Li-ion) rechargeable batteries (Kang et al., 2010). Cobalt sulfate is employed as a coloring agent in ceramics, enamels and glazes to prevent discoloration and as a copigment for the decoration of porcelain. In addition, cobalt sulfate has been used in animal feeds as a mineral supplement (Budavari et al., 1996; Kirk and Othmer, 1999).In the past, brewers used cobalt sulfate to prolong the life of beer foam (Kesteloot et al., 1968). Ranchers have dosed livestock with cobalt sulfate or used fertilizer enriched with this mineral to ensure that their animals obtained sufficient amounts of the trace mineral, which is essential to the production of vitamin B12. Cobalt sulfate has also been used in veterinary medication to prevent and treat cobalt deficiency in ruminants, which causes a reduction in feed intake and body weight, accompanied by emaciation, anemia and debility.Cobalt sulfate is a water-soluble bivalent cobalt salt. Cobalt sulfate heptahydrate dehydrates entirely at 420° C, and the dehydrated salt forms red monoclinic crystals."

Jan 1, 2015

Arsenic (As) removal behavior from Changgoon mine tailings was investigated using Acidithiobacillus ferrooxidans (A. ferrooxidans) in well-controlled batch reactors by varying pulp density (0.5?4%, pH=1.8, temp=30oC), reaction initial pH (1.8?2.2, pulp density=0.5%, temp=30oC), and temperature (25?35oC, pulp density=0.5%, pH=1.8). The initial concentration of As in the mine tailings used for bioleaching tests was about 30000 ppm, and the size range of tailings used in this study was 63?74 µm. The reaction speed and initial cell concentration were fixed to 150 rpm and 107 cells/mL, respectively. To complement leaching experiments, pH, oxidation/reduction potential (ORP), and amount of ferrous/ferric ions in leachate were analyzed. Scanning electron microscopy and x-ray diffraction analyses were also conducted for the samples before and after leaching to see if any morphological and compositional changes in tailings took place during leaching process. The As leaching efficiency increased with decreasing pulp density, decreasing pH, and increasing temperature in the presence of A. ferrooxidans. Specifically, no significant change in As removal rate was observed when pulp density d 2% while the removal rate dramatically decreased at pulp density of 4%. Regarding pH effect, As removal rate was much more enhanced at lower pHs (i.e., 1.8 and 2.0) compared to pH 2.2. Increasing temperature was observed to tend to enhance As removal rate, showing about 20% enhanced leaching rate under 35oC compared to 25oC and 30oC at the elapsed time of 5 days. The results for As removal behavior at different conditions (i.e., pH, temperature, pulp density) were consistent with the change in pH, ORP, and ferric ion concentration in leachate, showing greater removal rate at the condition with lower pH, and higher ORP and ferric ion concentration in leachate. Furthermore, decreasing removal efficiency was likely in part due to the extent of the formation of by-product (i.e., jarosite) of ferric ions.

Feb 27, 2013

By Dale D. Teeters

Today, I would like to talk about ways to maximize the efficiency of surface coal operations. I doubt I will present any startling new ideas, but my comments may, hopefully, stimulate some conversation today and later back at your own operations. Strip mining is a very old technique used by ancient societies. Only with the coming of the machine age in the early twentieth century did we attempt to increase the magnitude of our operations. The industry, as we know it today, really only got started in the early 1900s with the advent of steam shovels. In the first portion of this presentation, I will attempt to show that we have, in many cases, not changed the basics of strip mining, only the scale. In doing so, quite often we have complicated the operations to the point of being unmanageable and unprofitable.

Jan 1, 1981

By J. D. Miller, C. L. Lin

Appropriate software and hardware necessary to adapt a x-ray CT analyzer for determination of coal washability has recently been developed and sucessfully tested for well characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed x-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink-float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined.

Jan 1, 2001

By J. D. Miller, C. L. Lin

As the techniques and resolution for 3-D spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional x-ray microtomography offers a unique imaging capability. Spatial resolution on the order of ten microns can be achieved with the use of microfocus x-ray generators. Recently, a state-of-the-art cone beam x-ray microtomography system has been installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility has been designed to obtain 2048 x 2048 pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind, instrument will be used to obtain three-dimensional spatial reconstruction for such applications as specific examples 3D liberation analysis, pore structure analysis of particle beds during filtration and air-void system of concrete structures. The utilization of x-ray microtomography not only will allow for quantitative analysis of multiphase systems but also allow for textural characterization and the determination of phase continuity. In this paper, we present information regarding the current use of this new facility and reviewed potential applications for the advanced analytical system.

Jan 1, 2001

By E. A. Sarver

The Fe(II) regeneration process is an important aspect of Alternate Anode Reaction Technology (AART) for copper electrowinning (EW). In AART, Fe(II) is oxidized to Fe(III) at the anode during EW, and it must be regenerated to maintain recyclable electrolytes. Regeneration is achieved via Fe(III) reduction by SO2(aq), and the reaction is catalyzed by activated carbon particles. To better understand this process, a kinetic model was developed and experimentally validated for the Fe(II) regeneration in the current work. The investigation focused on the primary reaction mechanism and the reaction rate dependence on four variables: carbon particle size, flow rate, initial Fe(III) concentration and initial SO2 concentration. The Fe(II) regeneration reaction is mass-transfer controlled in the presence of activated carbon. Carbon particle size and initial Fe(III) are the most influential factors under the conditions tested. Initial SO2 concentration is insignificant to the reaction rate.

Jan 1, 2007

By Klaus Rieker

Over the last 30 years Wayss & Freytag Ingenieurbau AG has gained a lot of experience in mechanized tunnelling on various major projects. During this period most important developments concerning the machine technology for EPB- and Slurry-Shields have taken place. Since the first application of a hydro shield for the Wilhelmsburg Collector project in Hamburg in the early seventies, several stages of development have led to the current state-of-the-art in mechanized tunnelling. The continuous improvement of TBM techniques allows the execution of high quality tunnelling, particularly with regard to maximum safety and efficiency. The practical experience of the construction companies is of essential importance in order to continue further development and improvement.

Jan 1, 2005

By William G. Fischer

Basic laboratory tests initiated the. Rock Mechanics program. The stress-strain curve, modulus of elasticity, Poisson's ratio, the uniaxial rock strengths, Mohr's envelope, the stress at failure, and creep were investigated. A series of underground problems were then approached using this information; and various field measuring devices, most of which were developed by the Bureau of Mines. Initially, stress concentrations near mine openings were evaluated using the stress relief technique. This required an accurate determination of the pre-mining stress field. Later, stress concentrations associated with the cave line .sere studied. After about thirty stress reliefs over an appropriate time interval the effects of one type of mining could be compared against another. The microseismic technique was used to investigate a possible application of warning devices near the cave line. A study of mane reorientation was made Problems related to the shape and size of pillars and barriers were studied. Partial extraction mining systems were evaluated. The effectiveness of roof bolting patterns were examined. Control of roof stresses was attempted. A new system of mining in heavy ground has been developed using the information secured in the Rock Mechanics program without this system, mining in more than one instance would Nave been next to impossible. Indeed; from this one discovery alone, the Rock Mechanics program has paid off in improved safety as well as in dollars.

Jan 1, 1964

By G. Vallebuona

Currently, empirical models are used for predicting the hydrocyclone performance in terms of capacity, cut size (d50,c), water split and partition curve. These models, for example those of Lynch and Plitt, have been developed and checked for hydro cyclones with diameters larger than four inches. For smaller diameter hydrocyclones little empirical modelling has been done. This paper reports extended experimental research on small hydrocyclones. For these cyclones, the suitability of existing empirical models has been checked and their accuracy compared. Modifications of the existing models equations are proposed, improving their predictive capability for the small cyclones performance.

Jan 1, 1994

By Betty L. Gibbs

Microcomputers are becoming more convenient to use at all levels of the business world, including the mining industry and mine offices. The state of the mining industry requires that we become more productive and innovative in our analysis of deposits and operations. With the help of computers, examination of options to increase productivity can be performed quickly and inexpensively. Effective use of the computer for designing underground workings combines the calculation power and speed of a computer with the technical expertise and judgment of the engineer. Computer programs can perform calculations in minutes that could take an engineer several months. The engineer must be on guard when using the computer for any calculation because it is very easy to assume the results produced by a computer program are always correct. The computer is a sophisticated calculator but cannot recognize logical errors nor transposition of numbers. Also some intuitive or obvious decisions made by an engineer are difficult or impossible to program effectively.

Jan 1, 1987

By Enrique Levy

The publication from which this paper was abstracted is the first at-tempt to correlate all the metallogenic deta compiled by the author for the preparation of the 1:2,000,000 Metallogenic Map of Central America. It is not a treaty of metallogenic theories but rather a careful effort to postulate metallogenic provinces and epochs with the intention to stimulate other geologists and mining companies familiar with the area to criticize and improve on the ideas proposed. The sole purpose being to find new mineral deposits for the betterment of our people.

Jan 1, 1971

By W. J. Mahoney

A good quality assurance program at a coal mine or power plant is accurate, timely and consistent. The quality analysis is accurate due to a complete sampling of the coal stream loaded into the unit train. The sample analysis is accurate because standardized testing procedures are applied. Once an analysis is completed, the results must be communicated to the electric utility in a timely manner. The electric utility needs the results to better manage the coal inventory at its power plants. A quality assurance program can also help a mine deliver a consistent product to a utility's power plants. The importance of accuracy, timeliness and consistency are based on major changes that are taking place in the electric utility industry.

Jan 1, 1994

By V. S. Tadsen

Today, man is able to probe space because of technological advancements including the ability to control certain combustion reactions very precisely. The recent adjustment of the attitude of Skylab by radio command from earth is an excellent example of such control. It is strange, and indeed unfortunate, that very little is known about the mechanism of combustion of pulverized coal, the primary fuel for rotary kilns. The selection of a coal for direct pulverized firing of a rotary lime kiln may be determined by trial and error, persistence of sales personnel, proximate analyses, grindability, or apparent BTU cost. Occasionally, the only question asked is, "How much lime will it make?" To study the behavior of a particle of coal in the combustion stream of a rotary kiln is most difficult. We must, therefore, discuss the general mechanism of combustion of pulverized coal, and relate this mechanism to the selection of a proper coal for a rotary kiln. The classic three T's -time, temperature, turbulence -must be enlarged upon for a better understanding of the problem. Pulverized coal occupies only 0.01 per cent of the volume of air required for its combustion. This mixture behaves like a gas and the general laws governing the movement of solid particles in gasses are in effect. The differential velocity between air and coal particles depends on forced and natural convection, diffusion, and the length of time each particle is in the combustion space. As a particle of coal absorbs heat from its surroundings, it begins to give off volatiles". These gasses ignite as their kindling temperature is reached, and burn readily because of the excess oxygen immediately available. Combustion proceeds at this stage by the outward diffusion of gas from the coal particle into the surrounding oxygen-rich envelope. We could say combustion at this stage represents a small coal particle surrounded by an envelope of volatiles burning at their point of contact with sufficient oxygen. This release or expulsion of gasses from the coal may result in exfoliation or disintegration of the coal particle. If this occurs, and it is desirable that it should, it will accelerate the final stages of combustion. The escape of volatile material from the particle of coal and its subsequent combustion will cause increased turbulence around that individual particle. Ignition is maintained by radiation from gasses and solids in the combustion system, and most importantly, re-radiation from the kiln refractories and the process load.

Jan 1, 1978

By L. P. James, W. W. Atkinson

Utah has produced about one billion troy oz. (31.7M tonnes) of silver, more than any U.S. state except Idaho. Several very high grade ore systems, now closed, occur within large polymetallic limestone-hosted districts related to plutonic complexes. These Utah mines fed several major lead smelters for nearly a century. Interaction of magmatic chloride-rich fluids with carbonate rocks localized significant bonanzas within these districts. A low sulfidation state was produced in the fluids by their passage through limestones. The Bingham porphyry mine has also yielded more byproduct silver than other porphyry copper-gold systems. Away from exposed intrusive rocks, some large silver-only systems occur in Mesozoic sandstone and in caldera-related veins in volcano sedimentary rocks. Thick permeable latest-Proterozoic basement meta quartzite sequences present beneath western Utah may have been important, as perhaps they were in the Coeur d’Alene district of Idaho, in providing chloride and silver-rich ore fluids. However, it is clear that specific Tertiary magmatic events played an essential role in the evolution of the Utah silver-rich metallogenic province. The largest silver districts in the state are genetically related to porphyritic plutonic rocks.

Jan 1, 2000

By J. H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) amended the Federal Mine Safety and Health Act of 1977 to improve the safety of mines. The MINER Act established a Technical Study Panel (the Panel) to provide independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant materials in underground coal mining (1). Because frictional heating is a common cause of belt fires, the Panel recommended that the Mine Safety and Health Administration (MSHA) evaluate the drum friction test to determine if such a test would contribute to conveyor belt safety beyond that provided by the Belt Evaluation Laboratory Test (BELT). This paper compares the results of the drum friction test to results from the BELT and large-scale tests for six different conveyor belts. The results are used to evaluate the drum friction test as a method to determine the fire resistance of conveyor belts.

Jan 1, 2011

By Guodong Li, Chenlin Wang, Zibiao Yu, Bo Xu

Abandoned coal mines have many underground space resources, such as roadways, shafts, and gobs. Among them, abandoned roadways are the best gas storage space for underground compressed air energy storage (CAES). However, CAES caverns have high air pressure and strict sealing requirements. Therefore, the stability and sealing of abandoned roadways under high internal pressure must be analyzed. Afterward, the suitability of abandoned roadways used for CAES caverns should be evaluated. In this study, the numerical simulation software FLAC3D was used to calculate the stress, deformation, plastic zone volume, and pore pressure of surrounding rock in an abandoned roadway under 10 MPa internal pressure. The influence of buried depth, surrounding rock grade, and in situ stress state on roadway stability and the effect of surrounding rock permeability on roadway sealing were analyzed. Results showed that the stress, displacement, and plastic zone volume of surrounding rock were affected by high internal pressure when the buried depth was less than 300 m, but high internal pressure had little effect on them when the buried depth was more than 300 m. The suitable range of buried depth was more than 300 m. The optimal choice of surrounding rock grade was I and II, followed by grades III, IV, and V. The optimal choice of in situ stress state was σH > σh > σv, followed by σH > σv > σh and σv > σH > σh. The sensitivity of the stability evaluation parameters was ranked in descending order as follows: buried depth, surrounding rock grade, and in situ stress state. When the surrounding rock permeability was less than 1 × 10− 14m2, the 24-h air leakage rate of the roadway was less than 1%. The suitable range of surrounding rock permeability was less than 1 × 10− 14m2.

May 23, 2023