Search Documents

By R. L. Howell, L. C. Atkinson

Typical sedimentary sequences overlying coal seams consist of interbedded sandstones, siltstones, shales, and rider coal seams. In many surface coalmine settings, these sediments are saturated; and prior dewatering of them is necessary for effective and economic mining, including the stacking of saturated spoils. Such sedimentary sections usually have a very low vertical hydraulic conductivity that does not allow them to drain in a timely manner prior to their being stripped. One potential solution is installation of drainwells. Drainwells are small diameter wells that can collect water laterally from the various more permeable layers in the overburden and then gravity drain it to a lower layer – often the coal seam being mined – where it can be removed by pumping wells or sumps located in the bottom of the pit. A ground-water flow model utilizing the 3-dimensional finite element code MINEDW has been used to evaluate the effectiveness of usingdrainwells in a hydrogeologic setting that is typical of the Powder River Basin. A series of numerical simulations were completed using various combinations and spacings of drainwells and pumping wells to dewater the overburden and coal seams. The numerical simulations suggest that drainwells can be a very effective method of overburden dewatering.

Jan 1, 2000

By R. Bauer

Adaptations and redesign of the existing already very successful and proven road milling machine concept and technical innovations such as an optimized, specifically for mining application developed cutting drum, cutting housing design and cutting tools, high manoeuvrability achieved via a tight turning radius, a three disk clutch system and a cutting drum drive that allows for the acceptance of higher loads, a complete reinforcement of the chassis to withstand higher vibrations and torque, the installation of increased engine power via a modern drive unit, a specifically for mining/construction applications developed operator’s platform and finally a redesigned air intake system and the adaptation of the levelling system resulted in far more cost effective and advantageous capabilities of Wirtgen Surface Miner in soft to medium hard mining and construction applications. As the achieved results show for the first time in modern surface mining history mechanized cutting is capable to compete successfully against traditional drill, blast/ripping and other conventional mining methods.

Jan 1, 2007

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner's cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head's effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By A. Guzman

The design and construction of a new 140-ton-per-day R. O. M. phosphate rock scrubbing and washing plant was undertaken by Western Knapp Engineering Company, a Division of Arthur G. McKee and Company, for the J. R. Simplot Company, Minerals and Chemical Division, Pocatello, Idaho. The new plant replaces the owner's existing facilities at Conda, Idaho, seven miles northeast of Soda Springs in the southeast corner of Idaho. Replacement of the existing facilities became necessary because of loss in production and recovery. These losses were due in part to varying grades of raw ore from the mine and to the type of process equipment used in the old plant to upgrade the ore. Increase In production and grade was further necessary by demands created by expansion of facilities in Pocatello, Idaho, where all process ore from this plant is shipped. The new process scheme includes an ore-feeding system, scrubbing, screening, classification, wet cycloning, attritioning, filtering, drying, storage and shipping facilities. Space was also left for future increases of scrubbing and classification capacity and for heavy media separation. It is the purpose of this paper to take up some of the considerations necessary in the design of small mills in order to achieve the desired objectives of a successful plant, such as production, minimum operating cost and maintenance cost.

Jan 1, 1969

By M. J. Sapko

From 2001 to 2007, the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducted studies to develop alternative methodologies to full-scale explosion testing for deter-mining the ultimate strength of mine seals. As a result, the PRL developed and proposes an alternative seal-strength evaluation method based on a hydrostatic pressure-loading concept. The researchers suggest pressure loading a seal using water to twice the expected dynamic design load. The hydrostatic chamber test offers a means of validating seal designs, establishing appropriate resistance functions and determining the ultimate strength of seals through testing to failure. This article contrasts the full-scale explosion and hydrostatic testing of mine seals using a simple dynamic system model and principles.

Jan 1, 2008

By George M. McArthur

General Statement In Montana, as in most states, the requirements for water quality control are becoming more restrictive. What was once accepted practice is now obsolete. The planning and construction of water quality control facilities has taken on new importance. Past practices and new ideas must be examined to meet the challenge. By this paper we hope to encourage the exchange of ideas for the improvement of water quality control techniques. Both the mining industry and governmental agencies should benefit from such an exchange. The following is a summary of the work done and in progress by The Anaconda Company in Butte to provide an improved water quality related to production processes. We invite your comments. Acknowledgements This paper would not have been possible without the efforts of many individuals and departments in The Anaconda Company, including the Environmental Engineering Department, Mr. Frank J. Laird, Director; Montana Operations, Mr. M. K. Hannifan, General Manager, and their assistants.

Jan 1, 1972

Newmont Gold's methods for deposit modeling vary, depending on geology, mining and processing methods, economic feasibility and availability of historical information. It is argued that successful modeling requires understanding these factors, knowing the strengths and weaknesses of the various modeling techniques and being flexible in selecting the appropriate methods. Newmont is one of the world's largest gold mining companies, with operations in the United States, Peru, Mexico, Indonesia and Uzbekistan. And it is active in exploration worldwide. At the end of 1996, Newmont declared a total reserve of 1.15 equity kt (37.1 million equity oz) of gold and 2.17 equity Mt (2.39 million st) of copper. The gold deposits managed by Newmont totaled 752 Mt (829 million st) of ore containing 1.28 kt (41.3 million oz) of gold averaging 1.71 g/t (0.05 oz/st). In addition, Newmont is developing a porphyry copper-gold deposit that totals 9.1 Gt (1 billion st) of ore containing 380 t (12.1 million oz) of gold and 4.82 Mt (5.32 million st) of copper. (In May 1997, Newmont Gold Co. merged with Santa Fe Pacific Gold Corp., thus increasing Newmont's reserves to 1.72 kt or 55.2 million oz of gold and 2.17 Mt or 2.39 million st of copper.)

Jan 1, 1998

By Michael McNinch, LaTasha R. Swanson, Jennica L. Bellanca, Justin Helton

As manufacturers and mine operators develop and implement proximity detection systems (PDSs), they need to be mindful of the systems’ compatibility with mineworkers’ tasks, and possible unintended consequences. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) interviewed mineworkers at mine sites that currently use or previously have used PDSs on mobile equipment, including shuttle cars, battery haulers and scoops. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure and risk. Mineworkers also suggested that improved system task compatibility, training, logistics and PDS performance might help address these issues. Manufacturers and mine operators implementing this or similar technologies may also consider mitigating task incompatibilities up front, performing additional site-specific usability testing and restricting the use cases of the system to improve performance.

By Vladimir G. Kochnev

Crushing and grinding account for the major portion (60 to 80 percent) of the overall expenses for ore processing. Autogenous (AG) and semiautogenous grinding (SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills (Bassarear, 1982, MacPherson, 1989, Pithois, Casalis, 1983, Maripuu et al., 1983). However, there remains room for improvement to existing AG and SAG technologies and both technologies have immense economic benefit potential. Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that grinding in AG and SAG mills can be performed in a more effective way. The company's approach comprises the following elements: ? Novel mill design. ? New liners and lifters. ? Novel discharge grid design. ? Technique of treating material of critical particle size. Comparative tests that demonstrated the usefulness of these innovations are described in this article. Currently, there are hundreds of AG and SAG mills in operation throughout the world. Application of new internal elements of the mills and reconsideration of the circuit design of the existing grinding equipment using present technological solutions would significantly increase the throughput rate and diminish power requirement.

Jan 1, 2008

By R. W. Ballmer

Bingham Canyon lies in the heart of the Oquirrh Mountains, 25 miles southwest of Salt Lake City, Utah. In it is located the world's largest open-pit copper mine, owned and operated by the Utah Copper Division of Kennecott Copper Corporation. From the beginning of open pit mining operations in 1906 until 1963, the pit haulage, or materials transportation, was primarily by rail. In 1963, phase-in of a truck haulage system in the upper two-thirds of the pit was begun. The details of that conversion, its associated problems and the resulting pit operation have been covered in an earlier paper.1 The purpose of this paper is to discuss various factors for consideration in transportation system selection, and to discuss some of the alternatives considered prior to making the change from rail haulage to truck haulage for a portion of Bingham Canyon.

Jan 1, 1968

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and, thus, deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Sep 1, 2013

By J. A. Ryder

Compressed air is a relatively inefficient yet very convenient vehicle for transmitting mechanical energy. It is inefficient when compared to, say, hydraulic or electric energy systems since compressor and pneumatic machine efficiencies are quite low (in the range 20-65%) and reticulation losses can be quite high unless adequate pipe diameters are used to minimize friction drops. It is convenient in that capital and maintenance costs of pipes and machines are exceptionally low, the equipment is flexible and lightweight, the technological level is simple, the form of the energy supply is intrinsic- ally safe, and as an additional minor but psychologically important benefit, it provides a ready source of cooling and air supply for emergency use in deep hot mines. It is for these reasons that compressed air is a premier source of energy for many forms of underground equipment, in particular hand or rig-mounted rockdrills, some forms of rock- handling equipment, and a host of minor applications including agitators, small-lift pumps and temporary f am installations. In a typical S. African deep-level gold or platinum mine, compressed air generation accounts for 15% of the total mine electrical energy bill - more than is used for hoisting. In these mines it is not uncommon for over 100 km of underground compressed air piping to be installed, primarily to supply handheld rockdrills.

Jan 1, 1979

By Irwan S. Halim

For tunnels in horizontally bedded rock, geologic factors affect the selection and design of the initial supports, including the rock propensity toward parting along bedding and the resulting high potential for rock slabbing during excavation. To evaluate this ground behavior, numerical analyses and results with Mohr-Coulomb, Hoek-Brown, and Ubiquitous Joint constitutive models were used, using the Upper Rouge CSO tunnel in Detroit, Michigan as an example. The different rock models and other geologic considerations are shown to impact the selection of the tunnel initial support and design. This paper emphasizes the appropriate selection of an analytical model based on the site specific geology to achieve an optimum initial support design.

Jan 1, 2008

By Edward M. Dowey

The concrete lining for a long 8.05 km (5 mi) section of New York City Water Tunnel No. 3 was cast in place. The contractor, Grow-Perini-Skanska, placed over76,841 m3 (100,505 cy) of concrete, pouring 24 hours per day, 5 days per week. The concrete was dropped 204 m (670 ft) to the tunnel level, transported by rail to a concrete remixer and pump, and placed in 146.3m (480 ft) of full circle forms. Some of the many challenges include the sheer magnitude of the job, navigating through drifts, a raise and curves, dealing with ground water inflows, and placing the concrete within time limits.

Jan 1, 2001

By J. D. Morgan

In the first half of the year, lessening of cold war tensions was welcome. But Iraq's invasion of Kuwait in the second half led to the Persian Gulf War in January and February 1991. This caused an oil shock that dampened the economy. So the US gross national product rose only 0.9% to $5,463 billion (US billion = 109). The buildup of military forces in the Persian Gulf area focused greater attention not only on petroleum but also on other strategic materials. The Department of Defense continued to review stockpile goals and to upgrade several mineral materials. In addition, the Bureau of Mines continued to maintain the standby Emergency Minerals Administration. The Defense Production Act, which authorizes priorities, alloca¬tions and supply expansion, lapsed on Oct. 20. So the Selective Service Act of 1967 became the authority for assuring that orders of the armed forces and defense atomic-energy programs were given priority treatment. Consumer demand strongly affects mining worldwide. US citizens carry significant debt, and large stocks of housing and consumer goods are already in place. Some 250 million persons have 188 million licensed motor vehicles and 100 million dwelling units. Consequently, new car production fell 11 %, to 6.1 million units. Truck and bus production fell 8%, to 3.7 million units and new private housing starts fell 13% to 1.2 million units.

Jan 1, 1991

By Tina Živec, Žibertm Marko

"Civil design has changed in many ways using BIM (Building Information Modelling) technology in its most recent form. Such a technological breakthrough has not been successful so far in traditional oriented Engineering Geology, except in the Mining and oil exploration markets with budgets on much different scales. The fact is that paper, pencil and hand drawn sketches are still state of the art and a perfectly acceptable way of producing subjective geological interpretations.Using the technology available, we have developed a set of procedures and techniques to combine the latest surveying and remote sensing technology, GIS based tools to manage large data sets and BIM modelling techniques in a 3D geological environment.To demonstrate the concept, the forthcoming Karavanke tunnel project (Slovenia) has been chosen for testing techniques. The project, with its rich documentation from previous phases and new data available, represented a good basis for testing the possibility of digitizing geological data while communicating with Leapfrog Geo 3D modelling algorithms. This type of procedure would then allow engineers at the construction site to use the 3D model for prognosis and evaluation, while upgrading it daily with new information.INTRODUCTIONThe Karavanke tunnel crosses the mountain range on the border between Slovenia and Austria. As the geology is very complex due to its imbricate fan structure, a series of geological – geotechnical and hydrogeological investigations have been performed since the 1970s, resulting in extensive project documentation. The construction of the 7864 m long single-tube two-lane tunnel took place in the late 1980s. Currently, the tunnel represents a critical point on Pan-European Transport Corridor X (Salzburg, Austria – Thessaloniki, Greece), with insufficient safety measures. The need for improved traffic flow and enhanced road safety led the Slovenian government in 2013 to a decision to continue with activities regarding the construction of the second tunnel tube 70 m east of the existing tunnel.The extensive project documentation from previous investigation phases and construction of a new tunnel tube presented a good base for a pilot project, in order to test the emerging new technologies for data acquisition, processing and analysis in a 3D environment. Several products are available on the market for data acquisition and 3D geological modelling, but only a few can be applied in the civil design, as well. Developing a standard format and procedure for implementing the 3D geological model using new remote sensing techniques, 3D geological modelling tools, such as Leapfrog Geo and BIM (Building Information Modelling) modelling techniques would move the Engineering Geology, Geotechnics and Tunneling to a more advanced level. 3D modelling tools would therefore not only be used as a visualization tool, but would also contribute to in a more efficient communication and workflow between the professionals involved in the project."

Jan 1, 2016

By David W. Wisecarver

Kennecott Copper Corporation and the U. S. Bureau of Mines cooperated in a full-scale slope stability research project at the Kimbley Pit near Ely, Nevada. The west wall of the Kimbley Pit was mined from an over-all slope angle of 45° to an over-all slope angle of 57° and the pit was deepened nearly 50 feet. Mining was begun February 10, 1966, and completed October 30, 1966. Approximately 2.55 million tons of ore and waste were mined. The project was designed and carried out to learn more about the behavior of a pit wall as its slope angle is steepened and to obtain a possible insight into engineering parameters for use in design of future slopes. Data from this project are presented as obtained from (1) instruments installed in two adits for deformation and displacement measurements, (2) a subsidence network installed on the surface above the steepened wall, (3) pre- and post-mining observations of stress in rock, (4) sonic-velocity measurements, and (5) seismic and microseismic investigations. Changes occurred in measured quantities as the slope was steepened but stopped when mining was completed. Agreement was noted between the measured changes and predicted changes obtained from calculations using the finite element technique. Subsidence surveys and microseismic studies show the steepened pit wall to be stable.

Jan 1, 1968

By Paolo M. Brion, Z. Bade Sozer

"The Bypass Tunnel has high head conditions ranging from a minimum of 600 feet (183 m) under the Hudson River to a maximum of 875 feet (267 m) on the west side. The ground cover ranges from 425 feet to 900 feet (130 to 274 m). A two-pass lining is designed for the Bypass Tunnel. The bolted, gasketed precast segments carry the temporary hydrostatic and permanent ground loads. After the tunnel is put into service, the design assumes that the final lining, which varies from reinforced concrete to reinforced concrete with steel interliner, will carry the permanent hydrostatic loads. The design head for the segments is assumed at 775 feet (236 m), and the internal operating pressure head is around 1,200 feet (366 m). This paper discusses the design hydrostatic head and different load conditions considered for the segments, the load sharing between the segments and final lining, and the means employed to control water and hydrostatic pressure. PROJECT BACKGROUND The Rondout-West Branch Tunnel (RWBT), a segment of the Delaware Aqueduct, was built from 1937 to 1944 and provides about 50% of New York City’s total water supply. Monitoring and tunnel operations have shown that the RWBT is leaking up to 35 million gallons per day (MGD) (132.5 million L/day). In particular, two locations have been identified as areas of concern: Roseton and Wawarsing, as shown in Figure 1. The Wawarsing reach of the aqueduct will be repaired with an extensive grouting program when the RWBT is unwatered. However, because of the extensive nature of the leakage in the Roseton area, a Bypass Tunnel will be constructed to divert the flow around this area."

Jan 1, 2016

By William S. Alldredge

The Washington Metropolitan Area Transit Authority(WMATA) officially came into existence in February 1967 after the District of Columbia, Maryland, and Virginia joined in a com¬pact pursuant to Federal creative legislation signed the previous November to build a regional rapid rail transit system called METRO (1). The parent organization was the National Capital Transportation Agency (NCTA), a Federal agency, subject to Federal statutes and regulations. Soon after the completion of the transition from NCTA to the new "non-Federal" status of the Authority, the Board of Directors of the Authority formally adopted procurement policies and procedures (2). These are specific statements concerning competition by formal advertising for bids or by solicitation of proposals for negotiation, contracting authority, approval of awards, awards of contract modifications, and processing of claims and disputes. These policies and procedures are silent as to Federal procurement statutes and regulations. But because of the Authority's origin, the sensitive nature of the compact among the several sovereign jurisdictions, Federal financing of two-thirds of the costs, and the resultant surveillance by the General Accounting Office over staff operations, the Authority's procurement practices follow closely Federal regulations adapted to WMATA's needs. This is an important point and is the foundation of contractual relations between the Authority as the owner and its construction contractors. Various constraints and flexibilities of this arrangement with respect to excavation and tunneling contracts will be pointed out in the ensuing discussions.

Jan 1, 1974

By Lee Ann Arrington-Webb

Thiele Kaolin Co. has invested much time and money in achieving and maintaining its IS0 9002 certification. Through a regimen of process control and documentation, routine audits and a commitment to quality management, this kaolin producer is a competitive pigment supplier in a worldwide market. Background In 1987, the International Organization for Standards developed the ISO 9000 quality management system. This series of standards is used as a means to ensure customers that a quality management system is in place. Certification of a company does not mean that an individual product is of high quality. Rather, it demonstrates a supplier's ability to meet its customers' product and service needs. It also shows that a company has documented records to assure product consistency. The ISO 9000 system was begun in England during the early 1980s. During the mid-1970s, the British manufacturing industry was experiencing low quality. In an attempt to boost quality standards, the British government established the BS 5750 standards system. In 1987, BS 5750 was incorporated into ISO 9000. The ISO 9000 series consists of three levels of certification. ISO 9001 is the model for quality assurance in "design/development, production, installation and servicing." This standard applies to companies that rely on research and development to bring products that frequently change to market. ISO 9002 involves "production and installation" only. This standard is relevant to industries that produce a specific product according to specifications - either their own or their customer's. ISO 9003 is the model in "final inspection and test." This standard is the least detailed of the 9000 series. It is also the most applicable to companies that purchase, inspect or sort and resell. The quality system requirements for certification are outlined in the 18 elements of ISO 9002. These include: 4.1 - Management responsibility. 4.2 - Quality systems. 4.3 - Contract review. 4.4 - Design control. 4.5 - Document and data control. 4.6 - Purchasing. 4.7 - Control of customer-supplied product. 4.8 - Product identification and traceability. 4.9 - Process control. 4.10 - Inspection and testing. 4.11- Control of inspection, measuring and test equipment. 4.12 - Inspection and test status. 4.13 - Control of nonconforming product. 4.14 - Corrective and preventive action. 4.15 - Handling, storage, packaging, preservation and delivery. 4.16 - Control of quality records. 4.17 - Internal quality audits. 4.18 -Training. Continuous improvement, though implied in maintaining these requirements, could potentially be included in the quality system requirements in the next revision. The ISO 9000 requirements and documentation system is shown in the hierarchy pyramid (Fig. 1). A company's quality policy serves as the top of the pyra-

Jan 1, 1997