Search Documents

By Thomas M. Larimer

Prior to April, 1961, the coal charge to Clairtonts coke oven batteries was 3" x 0" mine waslied coal having approximately 6.0% to 7.0% moisture. Even at this size and moisture content, the arching, rat-holing and hang-up was excessive and the effective live storage of coal was only 60% to 70% of the rated capacity of the coal bunkers, depending upon the moisture of the coal. In addition, many production delays were encountered in the time and methods required to fill the larry cars. The need for an improved metallurgical coke led to the introduction of pulverized coal to a portion of the plant in 196 1. When the full potential of the pulverizing equipment was realized, we were able to serve seven batteries in our second unit of batteries with pulverized coal through two coal bunkers. The discharge hoppers of these bunkers were equipped with air vibrators to assist the flow of pulverized coal into the larry cars. The vibrators were helpful in this respect but required considerable maintenance and caused damage to the bin plates.

Jan 1, 1968

By James M. Barker

The occurrence of borates and zeolites at Mesa del Alamo is well documented by McAnulty and Hoffer (1) and Lefond and Barker (2). Further investigation indicates the presence of priceite and meyerhofferite in addition to the howlite (1) and colemanite (2). Analcime occurs in addition to the clinoptilolite and phillipsite (2). The Mesa del Alamo area is about 200 !a south of Tucson, Arizona, and 13 km southeast of Magdalena, Sonora, Mexico, just south of the unpaved road to Cucurpe (Figure 1). The geology and mineralogy of northcentral Sonora is known only on a regional basis except for small areas mapped in detail during copper exploration. The study area is within the Basin and Range province of North America from which borates and zeolites are now produced in California. The borates and zeolites at Mesa del Alamo occur in geological environments similar to those of the Mojave and Death Valley regions of California (3, 4). Thus, a detailed exploration pro- gram in the Magdalena area could result in the discovery of economic borate and/or zeolite deposits.

Jan 1, 1979

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT The pervasiveness of high-fidelity video games raises expectations of quality, detail, and lighting in virtual reality (VR) applications. However, high-quality models of mining equipment and environments are often not readily available, and developers may not be familiar with the latest techniques, such as physically based rendering (PBR). Because a consistent aesthetic is critical for maintaining immersion and controlling visual stimuli in research as well as in training, researchers at the National Institute for Occupational Safety and Health (NIOSH) created an asset development workflow. This paper details this workflow, including precision modeling and PBR techniques as well as a rigorous review process. It also describes lessons learned in the creation of photorealistic VR assets. BACKGROUND Virtual reality (VR) describes the simulated experience generated by an assemblage of hardware and software that are used to immerse the user. Over many years VR developers targeted the development of virtual environments (VE) toward various purposes: entertainment, the treatment of phobias [1], rehabilitation [2], and training [3]. A large part of the VE development includes digital assets, where digital assets refer to the non-programmed elements including 3D models, audio, and user interface. Because vision provides nearly 10Mbps of data [4] and accounts for the majority of all sensory input combined [5], a focused effort on asset appearance in VEs is warranted. Furthermore, research has shown that higher-resolution imagery increases search performance and training transfer, necessitating high-fidelity assets [6, 7]. In addition to being visually appealing, it is important that the assets and environment are also dimensionally accurate and consistent in order to elicit appropriate responses from the end users as they interact with and among these items [8, 9]. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed VEs and digital assets under several research projects over the course of the last two decades [10, 11, 12, 13]. This work has provided researchers with a strong knowledge base for digital asset development. However, the assets themselves have had limited reuse value. Due to the extended timeframes and limited scope of these projects, the previously developed assets are not consistent in visual quality and dimensional accuracy. Moving forward, researchers wanted to minimize future development time and use of resources as well as adopt new asset development tools and game engine technology. Therefore, the aim of this paper is to document a new asset development workflow including geometry, materials, UV layout, and shader implementation combined with review steps in order to produce high-fidelity simulation assets that are accurate with consistent characteristics, using repeatable methodologies that are well documented.

Jan 1, 2019

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By Edward D. Elkins

CalMat Co. is one of the largest producers of construction aggregates in the United States. The CalMat Reliance plant is located in Irwindale, California, and is situated on an alluvial fan formed by the San Gabriel River. The fan deposits are of Quaternary age and were derived from granitic and metamorphic bedrock exposed in the San Gabriel Mountains to the north. The sediments are poorly sorted and range in size from large boulders to clay size particles. The coarse material is hard and durable and consists of quartz diorite, granodiorite, granitic gneiss, schist and minor amounts of volcanic rock. The matrix is comprised of silty sand with varying amounts of clay. Thin silt and clay lenses occur sporadically throughout the deposit. The clay content of the matrix and the degree of weathering of the coarse material increases with depth. Based on seismic data, the alluvial fan varies from 200 to 400 feet thick and overlies crystalline bedrock. The Reliance plant was constructed in 1971 and 1972. It has a nominal capacity of 1200 to 1400 tons per hour, and typically produces more than three million tons of aggregate products per year. Alluvial fan sediments are mined from a gravel pit situated adjacent to the plant. The material is fed through a mobile, 48- by 60-inch, in-pit jaw crusher, then transported by conveyor to the main plant to be processed. The plant is modern and highly efficient. It has a typical wet and dry circuit and is capable of producing a wide range of aggregate products. To extend the life of the plant, a 9,000 foot conveyor system is being constructed to connect it to a granite quarry operated by Azusa Rock Inc. The quarry is located north of Irwindale, and is 50 percent owned by CalMat Co. The conveyor will be used to export crushed rock from the quarry to Reliance. The existing plant will be modified to process the crushed rock.

Jan 1, 1995

By Colin Lawrence

The Port of New York and New Jersey is one of the most heavily used transportation arteries in the world, handling nearly 40 per-cent of the North Atlantic shipping trade and directly providing nearly 230,000 jobs to the local economy. In 2004, $100 billion worth of consumer goods moved through the port. To accommodate future cargo volumes in the port, which are expected to double over the next decade and possibly quadruple in 40 years, deeper shipping channels are needed to provide access for a new generation of cargo mega-ships with drafts exceeding 13.7-m (45-ft) when loaded. Current channels within the harbor range in depths up to 13.7-m (45-ft), thus preventing carriers from using these larger ships, or requiring significant reductions in cargo to achieve lesser drafts to operate safely within the harbor. As part of the Harbor Deepening Project, the Anchor-age Channel would be deepened to 15.2 m (50 ft) below mean low water (MLW), for a length of 5,790 m (19,000 ft). The New York City Department of Environmental Protection (NYCDEP) owns, operates and maintains two existing water siphons in the harbor. Due to their shallow depth, both existing siphons must be relocated before dredging of the Anchorage Channel can be completed. Tom Costanzo, manager of capital programs for the Port Authority of New York and New Jersey (PANYNJ), says that ?While the re-location of the existing siphons under the Anchorage Channel is vital to the success of the deepening program, it is also a story of cooperation among key agencies at different levels of government resulting in improvements that will benefit the people of this region greatly.?

Jun 1, 2010

By T. Leftwich, G. Faison, K. Pavlich, R. Borden, S. Pavlou

Recent regulatory and policy initiatives under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect in risk reduction requirements for the mining and minerals processing industry. For example, Congress is considering regulating 20 special wastes from the processing of ore and minerals through RCRA Subtitle D and TSCA. The performance of risk analyses and environmental planning at mining projects is often driven by Federal and state regulatory standards. Recent regulatory and policy initiatives by the Environmental Protection Agency under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect on environmental planning and risk reduction programs for mining and minerals processing. Regulatory programs implemented under other Federal laws including the Safe Drinking Water Act, Clean Water Act, and Clean Air Act will also impact industry practices. This paper provides: 1) a brief overview of mining waste and mining waste management, and 2) a description of these regulatory initiatives and a discussion on the impacts of new requirements on environmental and risk reduction programs in the mining industry.

Jan 1, 1992

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By S. K. Kawatra

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1997

By CORA ROELOFS

While the COVID-19 pandemic has dominated the headlines, another epidemic in the United States has continued apace — the opioid epidemic. Half a million opioid overdose deaths have occurred in the United States since 1999, when the opioid epidemic began. The causes of the epidemic include the rise in prescriptions for opioid pain medications, including for work-related pain. Miners and other occupations identified as physically demanding and at higher injury risk have been found to be at increased risk for opioid overdose [1]. However, awareness of the risk factors that might lead to opioid use, the potential hazards associated with their use, and resources to prevent addiction and death can allow miners to make choices that can reduce these risks.

By Mitchell L. Fong

The Bay Area Rapid Transit (BART) District will be extending BART service south along an 8.7-km (5.4-mile) -long corridor in the city of Fremont, California as part of the Warm Springs Extension (WSX). The WSX project will link the existing BART system to the future BART to San Jose extension. A segment of WSX is located in Fremont Central Park (referred to as the Fremont Central Park Subway Project). The Fremont Central Park Subway is considered the most complicated and geotechnically challenging portion of the project with an underground subway box being constructed near the active Hayward Fault which is capable of ground motions up to 0.75 g and is located in an aquifer which is used for water storage and supply. Soil-structure interaction analysis was used in the design of the subway box to resist deformations due to earthquake ground motions. A water-tight excavation support system has been designed to allow subway box construction while minimizing impacts to the aquifer.

By J. M. Johnson, J. Vialpando, C. Lee

Since 1951, Molycorp has operated the Mountain Pass Mine in San Bernardino County, California to extract fourteen lanthanide elements, or rare earths, from a carbonate ore body. Wastes generated by the open pit mining operation consist of overburden and 1800 tpd of tailings. The tailings are classified as Group B mining wastes by California regulators. Paste tailings is one of several alternatives being considered during the permitting process for future mine operations. This paper presents the findings of study to assess the feasibility of using paste tailings to develop an unsaturated tailings stack instead of dilute slurry discharge behind a tailings dam.

Jan 1, 2004

By J. Gauntt

Calcium carbonate is one of the most widely used industrial minerals in applications like cement, lime, agriculture, power plant fluegas desulfurization (FGD) and construction aggregates. Most applications are generally high-volume and low value ($9/t or $10/st) or less free-on-board (f.o.b.) mine site) uses of this material. Specialty uses of ground calcium carbonate (GCC) are typically referred to as ?performance mineral? or ?extender and ?ller? applications. Primary specialty markets for GCC include paper and plastics as well as a number of construction applications including joint compounds, carpet backing, paint, and adhesives, caulks and sealants (ACS). Other important specialty applications for GCC include rubber, food and personal care products. A new and growing application for GCC is in nonwoven fabrics, where this mineral replaces a small percentage of the polymer. Typical specialty applications for GCC are color sensitive and require extremely white/bright materials. Although deposits of limestone are located in most states, high brightness resources are relatively rare and controlled by a limited group of suppliers.

By Helmut Hass, Michael S. Shultz

For many tunneling, deep shaft and deep excavation projects ground freezing is one of the best if not the only technique available to create a watertight and load bearing temporary support system in soft ground conditions. When appropriate attention is given to the details of the ground freezing system design, ground freezing is a very safe method and is economically viable with competing techniques and combinations of techniques. Recent innovative uses of the technique in Europe are highlighted in this paper and compared with current uses in North America.

Jan 1, 2005

By Shiwei Wang, Ziwen Li, Chenhu Zhang, Peng Chen, Chengyong Wang

Accurate prediction of the partition coefficients in coal gravity separation is key to improving the preparation efficiency of coal and promoting its clean utilization. In China, the approximate formula method (AFM) has been applied to the calculation of coal gravity separation partition coefficients for decades, but its accuracy is limited. To improve the accuracy of the predicted partition coefficients, and thus the product yield of coal preparation plants, the present study proposes a modified hyperbolic tangent model to derive direct calculation formulas for the heavy medium and water medium separation partition coefficients. Four groups of coal samples were used to verify the accuracy of the direct formulas, and their predictions were compared with those of the AFM. The results showed that the partition coefficients and partition curves predicted by the direct formulas were closer to the actual values than those predicted by the AFM. Further, when the cleaned coal ash content was basically the same, the cleaned coal yield predicted by the direct formula was lower than that predicted by the AFM, and was also closer to the actual value. These results demonstrate that the direct formula produces more accurate results compared to the conventional AFM. As this formula has a reasonable theoretical basis, is simple to apply, and produces accurate results, it is expected to help improve the design and management level of coal preparation plants.

Oct 15, 2022

By K. T. Mau

Hawaii is located approximately 2,500 miles from the mainland, but has basic needs for its thriving developing community. Cement is one of these needs Cement production in Hawaii is not without handicaps. The necessary raw materials are practically non-existent except for limestone. Even at that, the available limestone is marine in origin, coralline in nature and amorphous in characteristics - unlike calcite which is normally the calcium carbonate source for cement manufacture. There is no clay or shale for the argillaceous portion of cement raw mix. Hawaii being volcanic in origin is too young geologically for clays and shales to evolve and whatever there is, most likely is washed into the ocean.

Jan 1, 1982

By G. Deschênes

In Part I of the work, gold and silver were shown to be efficiently extracted from Kupol samples using lead nitrate in a cyanide leach system. In Part II, a comparison of the technical and economic merits of a new technology called CELP (CANMET Enhanced Leaching Process) was made with the cyanidation/AVR(Acidification-Volatilization-Recycling) process using 8 metallurgical variability samples as well as a large composite sample which represented initial two years of Kupol mill feed. The composite sample had 33.4 g/t Au and 289 g/t Ag. The metallurgical demonstrated that the CELP produced very similar gold and silver leach extractions compared to the standard Cyanidation /AVR leach conditions at 1/2 the cyanide concentration (1000 ppm NaCN in CELP vs. 2000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton, were approximately the same for the two technologies (total cost of the CELP with the use of Merrill-Crowe at $46.48/ton, with cyanidation/AVR at $46.13/ton). However, the implementation of the CELP would eliminate a capital expenditure of approximately $5 million. Eight variability samples used to confirm the previous results showed that on average the gold and silver leach extractions with the CELP and the feasibility leach conditions were very similar for gold extractions, but 4.6% higher for silver extractions compared to the conventional cyanidation. The decision was made to remove AVR cyanide recovery from the Kupol flowsheet and implement the CELP at Kupol. The ability to use conventional leach equipment with the CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2009

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. Contrary to most copper sulfide minerals where recovery is principally liberation controlled, the recovery of molybdenite is much more complex with fully liberated particles commonly lost to tailings. It is this complexity that facilitated the necessity for a geometallurgical investigation of molybdenite from the Bingham Canyon deposit. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes (i.e. morphology, angularity, liberation, size) have on the recovery of molybdenite in the processing circuit. A set of samples was collected from the ores and products produced by Rio Tinto Kennecott’s Copperton Concentrator. All samples were analyzed using normal polarized reflective light, Mineral Liberation Analyzer (MLA) and X-ray diffractometery (XRD) techniques. The results of this investigation revealed the presence of two distinctly different types of molybdenite, which have been identified as the two polytypes of molybdenite, i.e. hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the core of the Bingham Canyon deposit. The 3R polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Concerning their metallurgical behavior each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. For instance, the 2H polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high quality molybdenum concentrate under normal operating conditions common to most copper concentration operations. In contrast, the 3R polytype is difficult to grind and kinetically “slower” floating with surface attributes that less amenable to recovery under normal operating conditions. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to the normal operating parameters may be necessary to improve the recovery of molybdenum. Finally, a preliminary investigation into the metal budget of porphyry Cu and Mo deposits indicates that a positive correlation may exist between the total economic metal budget and the polytype content. For example, higher concentrations of the 3R polytype appear to be more prevalent in Au-enriched porphyries versus Mo-enriched porphyries. This observation may also serve to help explain why it is easier to obtain high rates of recovery in Mo ± W-rich deposits, which contain little to none of the 3R-polytype. Consequently, the potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present, as well as its impact on the economics (exploration) and/or on the processing circuit (plant design) could exist. In conclusion, this investigation highlights the necessity of understanding the mineralogical properties or characteristics of molybdenite and/or other economic mineral(s), as these can and will have a direct impact upon the performance and plant optimization."

Jan 1, 2016

By Richard W. Cannon

INTRODUCTION The authors, by means of this paper, will attempt to show the role of Induced Polarization and Resistivity surveys in the discovery of the orebodies of Gibraltar Mines Limited (N.P.L.). In this paper, we will also attempt to show the importance of conducting large enough surveys in order to properly evaluate the results obtained from these surveys. LOCATION The orebodies of Gibraltar Mines Limited (N.P.L.) are located on the western slope of Granite Mountain, central British Columbia (52°30' north, 122°16' west) (See Fig. 1). The property lies approximately 28 miles north of Williams Lake, B.C. and can be reached by way of 10 miles of newly improved road from McLeese Lake, on the Cariboo Highway. The area in and around Gibraltar Mines has a moderate topographic relief with elevations between 3,500 and 4,100 feet. {EARLY HISTORY AND GEOLOGY The present Gibraltar Mines property before amalgamation consisted of the Pollyanna property (Duval-Canex) and the Gibraltar property (original Gibraltar Mines) as well as some Coast Silver and McLeese Lake Copper claims (See Fig. 2). The Pollyanna property was first described in the 1917 B.C. Minister of Mines Report which referred to it as the "Rainbow Group". The development at that time consisted of several open-cuts on copper bearing quartz veins.

Jan 1, 1972

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014